Search Documents

Provide improved permanent stoppings designed specifically for use in mines with large cross-sectional entries. Approach The large entry sizes in many mines, such as oil shale, salt, and limestone, make the conventional stopping construction techniques used in smaller opening mines unacceptable. The Bureau of Mines and Colorado Mining Association jointly sponsored a contract to design and test new or modified stopping concepts for these mines. The most promising concepts were then tested in an oil-shale mine having 30-foot-high by 55-foot-wide mine entry openings. All stopping designs tested were evaluated in terms of cost, air tightness, and resistance to blast damage.

Jan 1, 1987

By J. B. Umhau

During 1928 the United States consumed 73,270 long tons of virgin or primary tin, which was approximately 7.5 per cent more than the 68,198 long tons con¬sumed in 1927 and equaled 41 per cent of the world's production in 1928 (approximately 178,000 long tons). Consumers' stocks amounted to 9,268 tons on January 1, 1928, and 8,587 long tons on December 31, 1928, a net reduction of 681 tons. In addition to the virgin tin accounted for above, 12,106 long tons of secondary metallic tin were used by manufacturers of tin products in 1928. These figures are the result of an inquiry addressed by the Bureau of Mines to manufacturers to determine the amount of metallic tin used by them; in reply, 1,307 establishments reported consumption in 1928. The distribution of the amount consumed by various uses, as shown in the allowing tabulation based on Bureau of Mines canvasses for 1927 and 1928 in comparison with consumption by uses reported by the War Industries Board for 1917, emphasizes the fact that new uses for tin have been developed in only minor or insignificant amounts. Furthermore, although the studies for recent years show that some older uses have been discontinued, the amounts involved were all small and insignificant. Variation in consumption from year to year parallels the fluctuations in demand for the already well-established tin products. For example, the manufacture of bearing metals and solders for motor cars and trucks required 19,000 tons in 1928 compared to 16,000 tons in 1927; the canning industry continues to require the greater portion of the tin plate and also much solder. Growth in the electrical and the more recently developed industries (aeroplane, refrigerators, radio, etc.), while affecting total consumption of bearing metals, solders, etc., has made little change in the proportions required for these basic methods of using tin.

Jan 1, 1929

By G. J. Conroy

This Bureau of Mines study was initiated to determine whether or not a large-scale investigation of 400-Hz applications in coal mines was justified as a means of increasing safety in operations due to size and weight reductions in portable and other mining machinery. Potential uses for 400-Hz power in mining operations are explored, and cost and size comparisons with 60-Hz systems are made. The use of variable-frequency motor drive is suggested for conveyors. The conclusion was reached that there is no significant potential safety increase due to a general size and weight reduction, as the fact of such general reduction cannot be demonstrated.

Jan 1, 1974

By Paul M. Tyler

The enormous deposits of greensand in New Jersey and elsewhere in the United States, many of them close to important octant industrial centers, constitute a perpetual challenge for research chemists to convert them into a commercial asset of national importance. Following the introduction of more concentrated fertilizers, comprising synthetic mixtures of more soluble salts, the quantity of greensand used directly upon the soil has diminished, but deposits of such material still have at least potential value locally for use not only as fertilizer but also as a water softener. An annotated bibliography of the already extensive Literature on greensand, virtually complete to about the end of 1929, has been issued by the Bureau of Mines3/, and the commercial aspects as well as the technology of greensand utilization are discussed in available publications, The purpose of the present circular, therefore, is merely to provide a brief outline of certain general essential considerations for use in appraising the potential value of a greensand deposit in any given locality.

Jan 1, 1934

By W. E. Wallace, S. -G. Xing, M. J. Keane, J. C. Harrison

"SummaryDiesel-exhaust particles from two sources were dispersed in aqueous mixtures of dipalmitoyl phosphatidyl choline, a major component of pulmonary surfactant, and were tested for genotoxicity. Diesel samples from the same sources were extracted with dichloromethane and transferred into dimethyl sulfoxide and subjected to the same assays. Both types of extractions yielded similar results in both the Salmonella mutagenicity assay and the sister-chromatid exchange assay using V79 cells. After separation of the samples into supernatant and sediment fractions, the activity of both diesel samples was shown to reside exclusively in the supernatant fraction for the solvent-extracted samples, and exclusively in the sedimented fraction for surfactant dispersed samples. These findings indicate that genotoxic activity associated with diesel particles inhaled into the lung may be made bioavailable by virtue of the solubilization / dispersion properties of pulmonary surfactant components.While diesel engine emissions are associated primarily with transportation, they are also very common in the workplace. Estimates for the U.S. are that as many as 1.35 million workers in as many as 80 000 workplaces are exposed to the combustion products of diesel engines (NIOSH, 1988). These occupations include, but are not limited to mining, agriculture, motor vehicle maintenance, fork lift truck driving, truck driving, and tunnel and bridge operation."

Mar 1, 1992

Reduce respirable dust exposure of workmen operating auger-type continuous mining machines. Approach: An auger miner was fitted with an exhaust system which draws dust laden air through a [scruber] and discharges it behind the line curtain. How It Works: Dusty air is drawn into the space above the coal conveyor and through a scrubber, by two fans mounted side by side above the conveyor. Exhaust from the fans passes through a duct to the side of the auger miner, and into tubing that runs back and into the air return passage formed by the line curtain. See Figure 1. Of the 5,000 cubic feet per minute of air normally entering the working place, 4/5 is drawn out through the dust exhaust system. The system was installed on a Wilcox Mark 20 Miner and tested underground by personnel of the Bureau's Pittsburgh, Pa., Mining and Safety Research Center, under a cost sharing

Jan 1, 1976

By R. L. Montgomery

The heats of solution of erbium chloride in water and in hydrochloric acid and of erbium oxide in hydrochloric acid were determined. The results reveal a discrepancy of 10.5 kcal. per gram-atom between the heats of combustion and solution of erbium reported in the literature, the heat of combustion being more negative. The heat of combustion of erbium t4)4 and its heat of solution in hydrochloric acid (1, 18) have been reported in the literature. The heat of solution of erbium chloride was determined in two studies (2, 19). The present work was undertaken to check the reported heats of solution of erbium chloride and to determine the heat of solution of erbium oxide in hydrochloric acid. The latter quantity permits the heats of combustion and solution of erbium to be compared for mutual consistency. It was also desired to determine the degree of similarity between the thermochemistry of yttrium and erbium.

Jan 1, 1961

By Thomas O. Glover

Cameroon continued to enjoy sustained economic growth that began with its independence in 1960. Growth in the gross domestic product (GDP) averaged 2.8% per year during the 1960's and the first half of the 1970's. Starting in 1976 and for the succeeding 10 years, the GDP accelerated rapidly owing to the coming on-stream of Cameroon's small but domestically significant offshore oil industry. In 1985, the GDP grew by 7.8%, but in 1986, it was only up 5.5%. The country's sustained economic growth in dollar terms of gross national product (GNP) per capita reached $1,075 in 1986. The ranking in GNP per capita by the International Monetary Fund put Cameroon in the middle-income category for developing countries. The sustained economic growth rate up to 1986 was due to the injection of income from oil into the economy, but crude oil price reductions in 1986 brought a slowdown. In 1986, crude oil production grew to 200,000 barrels per day, an increase of 8.2% from that of 1985. Most of the oil came from the Société Nationale Elf Aquitaine (SNEA) wells in the multifield Rio del Rey complex. Additional output came from the Moudi Field operated by Compagnie Française des Pétroles S.A. Proven oil reserves in Cameroon were 540 million barrels. At 1986 production rates, and in the absence of further discoveries, Cameroon will have exhausted its recoverable oil reserves by the year 1995. Owing to worldwide crude price reductions, the country's oil income fell 60% between 1985 and 1986, from $1.82 billion2 to $0.72 billion. Cameroon's refinery operator commenced operating the Sonara refinery in 1981 at Point Limboh. Sonara's capacity of 43,000 barrels per day was small by most standards. In 1986, natural gas reserves, estimated at 100 billion cubic meters, were not produced commercially because there were no domestic users. Proposals for a multibillion-dollar liquefied natural gas plant at Kribi had been submitted; however, work on the plant had not commenced.

Jan 1, 1988

By E. P. Youngman

This paper presents one of a series of digests of foreign mining legislation and court decisions that is being prepared in advance of a general report relative, to the rights of American citizens to explore for minerals and to own and operate mines in various foreign countries. This interpretation of the mining laws of British Guiana has been prepared from the best available sources in Washington and is, released subject to amplification and correction, if necessary, by United States foreign-service officials. INTRODUCTION The sources of information available in the preparation of this paper are the following: 1. The Crown lands ordinance, No. 32 of 1903, September 26, 1903.

Jan 1, 1934

By R. L. Solmer

During 1959-61, the Bureau of Mines investigated the strain and deformation induced in rock and concrete linings around mine openings by retreat panel caving at the Climax Molybdenum mine. Two concrete-lined slusher drifts on the Phillipson level of the mine were instrumented with both electrical strain gages and extensometers. Changes in strain and deformation were recorded over an 18-month period during the undercutting and caving of the mining panel. General agreement was found between the strain and deformation measurements and the hypothesis that the vertical component of the stress field on the openings is almost completely removed by undercutting. This phenomenon is a possible explanation for the structural failures that occur in the slusher drifts during the undercutting cycle.

Jan 1, 1965

By C. M. Palencia

The Bureau of Mines evaluated the potential availability of molybdenum resources from 88 mines and deposits that account for more than 90 pct of the demonstrated resource base in market economy countries (MEC's). For each property, tonnage-cost relationships were developed that indicate the molybdenum potentially available at different average production costs, including a 15-pct rate of return on invested capital. From the 23 MEC primary deposits, 2.5 billion 1b Mo was determined to be potentially available at a price of $411b, rising to 4.7 billion 1b Mo at $8/lb. Copper price-molybdenum tonnage relationships were developed for those mines and deposits from which molybdenum can be recovered as a byproduct of copper production. This analysis showed that another 3.4 billion lb Mo is potentially available based on a copper price of $0.7511b, rising to 4.3 billion lb Mo at $l.00/lb. The United States has been the world's largest molybdenum supplier since 1924. Its remaining resources are sufficient to meet the domestic demand of 57 million lb/yr Mo (averaged for a 10-yr period) through the end of the century. Production from primary domestic mines was suspended during most of 1983 because of oversupply of materials. A major concern is the cheap molybdenum byproducts from foreign copper operations in which employment and the need for hard currency override economics in meeting production goals.

Jan 1, 1985

In presenting this list of permissible explosives and blasting devices, the Bureau of Mines desires to call attention to pages 19 and 24 outlining, the conditions in use under which, and only under which, the explosive or blasting device is permissible. In view of a recent publication recounting trade practice favoring the use of a blasting device without stemming, particular emphasis is placed upon condition 4 on page 19 and condition 2 on page 24. An explosive or a blasting device enumerated in the permissible lists of this Bureau is not permissible in use unless it is properly confined with clay or other incombustible stemming.

Jan 1, 1940

In presenting this list of permissible explosives and blasting devices, the Bureau of Mines desires to call attention to pages 19 and 24 outlining, the conditions in use under which, and only under which, the explosive or blasting device is permissible. In view of a recent publication recounting trade practice favoring the use of a blasting device without stemming, particular emphasis is placed upon condition 4 on page 19 and condition 2 on page 24. An explosive or a blasting device enumerated in the permissible lists of this Bureau is not permissible in use unless it is properly confined with clay or other incombustible stemming.

Jan 1, 1940

By Sandip K. Mukherjee

This report presents the results of the economic analysis of several applicable alternatives to increase airflow in four underground coal mines. Pressure-quantity surveys were conducted underground and measurements were also made at the main mine fan(s). The existing ventilation networks were modeled using the modified Penn State ventilation simulator. The applicable alternatives were simulated. Performance data obtained from these simulation runs were utilized to conduct the cost-effectiveness analysis. The costs for each of the alternatives included capital, operating and operating costs. These costs were expressed as annual ventilation costs per active section in terms of dollars per cfm taking into account the economic life associated with each of the alternatives. The benefits were expressed as increased airflow quantity in the critical sections. A section of this report also deals with comparison of simulator predicted air quantity values against air quantity values measured under-ground. This volume constitutes Volume II of the report and contains the outputs of the computer simulation runs.

Jan 1, 1983

By Robert G. Bottge

The Bureau of Mines investigated the availability of the land in south-central Alaska for exploration and mineral development of locatable minerals under State or Federal laws. The land ownership for an area of nearly 72.5 million acres in south-central Alaska was divided into 3 availability categories and 15 subcategories. In July 1985, 31.0 million acres of the study area were available for mineral exploration and development, 6.2 million acres were available with restrictions, and 35.3 million acres were unavailable. About 23.6 million acres in the study area are underlain by mineral terranes. About 9.9 million of the 23.6 million acres are available for mineral entry, 2.4 million acres are available with restrictions, and 11.3 million acres are unavailable. While much of the land currently classified as unavailable will be reclassified once it is conveyed to the State or to Native corporations, about 22% of the unavailable lands underlain by mineral terranes are now Federal parks, preserves, wildlife refuges, wild and scenic rivers, and military lands, all of which are considered permanently unavailable for mineral exploration and development.

Jan 1, 1986

By K. O. Bennington

Cancrinite is one eonstituentof "red muds," a high-volume waste product of alumina production by the Bayer process. The Bureau of Mines determined the thermochemical properties of cancrinite as part of a program to provide such data for minerals of industrial importance. Cancrinite [Na7.68(A16Si6024)(N03)1.68 (H2O)4.1] was synthesized by reacting aluminum silicate gel with a solution of NaOH and NaN03, and the composition was determined by chemical analysis, differential scanning calorimetry, and thermogravimetric analysis. The heat of solution was determined by hydrofluoric acid solution calorimetry. The standard enthalpy of formation at 298.15 K, ?Hf°298, is ?Hf°298 = -3,487.97 ±2.6 kcal/mol, and the standard enthalpy of formation from the oxides and NaN03, ?H°298, is ?H°298 = -215.20 ±l.8 kcal/mol.

Jan 1, 1983

By K. C. Dean

Changes in the types of materials used for the construction of recent automobile models have occasioned a review of the continued applicability of current recycling techniques. Plastics are being used increasingly in late model cars. To evaluate the changes occurring, a 1972 Mercury Montego, furnished by the Ford Motor Co., was completely dismantled and analyzed, and the composition was compared with that of a composite automobile from 15 vehicles ranging in date of manufacture from 1954 to 1965 and designated as a circa 1960 model. The composite vehicle contained about 26 pounds of plastics, while the 1972 model contained over four times that quantity. The increasing use of plastics in automobiles suggests that research to improve the economic potentiality of plastics recycling is warranted.

Jan 1, 1974

By Murray Jacobson

The respirable dust standard in the Federal Coal Mine Health and Safety Act of 1969 is designed to prevent disability and death from coal workers' pneumoconiosis. Beginning June 30, 1970, the operators of coal mines were required to maintain the average concentration of respirable dust in the active workings at or below 3.0 milligrams of dust per cubic meter of air. The standard is reduced to 2.0 milligrams per cubic meter after Dec. 30, 1972. This paper presents the equipment and procedures used by the coal mine operators in implementing the respirable dust sampling program established by the Secretary of the Interior and the Secretary of Health, Education, and Welfare and shows the effect of the law, during the first year, on the reduction of dust levels in selected mines. The system employed by the Bureau of Mines for analyzing and processing the dust samples is also presented.

Jan 1, 1971

By T. Estelle Gardner, A. R. Taylor

Heat capacity measurements were made on sodium bromide ( NaBr ) and sodium iodide ( NaI) in the temperature ranges of 7 ° to 300 ° K and 56 ° to 300 ° K using an adiabatic calorimeter . Smooth values of heat capacity, entropy , enthalpy function , and free- energy function were calculated from the heat capacity data at 10° K intervals and at 273.15° and 298.15° K. Entropy and free energy of formation values at 298.15° K also were calculated for the two compounds using entropy values determined in this study and other data reported in the literature . The entropy values calculated at 298.15 ° K were 20.75 ± 0.06 entropy units (eu ) for sodium bromide and 23.55 ± 0.07 eu for sodium iodide .

Jan 1, 1964

[In selecting deposits of exploration projects, tabular deposits or large mineralized masses are favored because they may be explored systematically and because they afford the best opportunity for blocking out reserves in advance of mining, whereas irregular, small pipes and scattered]

Jan 1, 1941