Search Documents

By E. H. Denny

Colorado coal-mine fatalities, which have gradually decreased since 1914, have shown a marked decline since 1924. Data on coal-mine fatalities in Colorado published by the U. S. Bureau of Mines5 indicate that the deaths per thousand 300-day workers have decreased from 9.13 in 114 to 6.14 in 1926, and that the deaths per million tons produced have decreased from 9.18 in 1914 to 4.98 in 1926. Table 1 gives fatality rates in Colorado and in the United States from 1914 to 1926 inclusive. [ ]

Jan 1, 1929

By Foster Fraas

A comparison has been made between cubes and spheres in the matrix of the high-intensity wet magnetic separator. For two inclined plane surfaces, such as may occur with cubes, the maximum force value, H [dH-dx] is at the point of nearest approach and is much higher than the force resulting from adjacent spheres. Although the maximum force value for cubes is higher, it decreases more rapidly at increasing distances. The maximum force for spheres is at an appreciable distance from the point of nearest approach. At field intensities for magnetic saturation of the iron spheres, the force extends to further distances with greater uniformity approximating that of the constant force or isodynamic field. The force is also independent of the sphere diameter, which permits the scaling of the sphere diameter to provide changes in particle migration distances without changes in force gradient.

Jan 1, 1972

By C. O. Karacan, S. J. Schatzel, W. P. Diamond

In coal mining, longwall mining is a preferred method to maximize production by extracting large blocks of coal that have been outlined with a set of development entries. In U.S. mines, longwall panels are typically 305 m (1,000ft) wide (with a continual trend towards even wider panels), and usually over 3,050 m (10,000ft) in length. The increasing size of longwall panels, while helping to increase coal production, may also increase methane emissions due to the exposure of the mining environment to a larger area of fractured, gas-bearing strata. Thus, understanding the impact of increased panel widths on methane emissions, and designing gob gas ventholes and bleeder systems accordingly, can enhance the safety of the underground workforce by reducing their exposure to potentially explosive accumulations of methane/air mixtures. As part of its mine safety research program, NIOSH’s Pittsburgh Research Laboratory has initiated a reservoir modeling effort to better understand the interaction of the various geotechnical factors influencing gas flow within and to the underground longwall mining environment. A focus of this modeling effort has been 1) the prediction of the incremental amount of methane emissions to be expected due to increasing longwall panel widths, and 2) optimizing gob gas venthole completion practices to capture more of the gas in the subsided strata above longwall panels before it can enter the ventilation system of the underground workplace. The history matching phase of the study has been carried out on a 381-m (1,250ft) wide panel in the Pittsburgh Coalbed. Simulations have also been completed for a 442 m (1,450ft) wide panel to estimate the incremental increase in methane emissions and the performance of current gob gas venthole placement configurations. Additional venthole placement configurations were simulated to investigate options for optimizing methane capture from the subsided strata above the wider longwall panel.

By E. G. Davis

The Bureau of Mines investigated gaseous direct reduction of low-grade iron ore concentrates in a continuous fluid-bed reactor. These studies were made in a 4-inch diameter fluid-bed reactor using hydrogen alone, and oxygen-or air-reformed natural gas as the reductants. The percent reduction is directly dependent on the mole ratio of hydrogen in the reducing gas to the oxygen associated with the iron oxide in the ore. Two-and three-stage fluid bed tests were simulated by repeated continuous tests. The results showed that percent reduction of the final product was dependent on the mole ratio of the quantity of hydrogen in the gas of each stage to oxygen in the iron oxide of the initial ore feed. Reduction as high as 87 percent in the single stages and as high as 94 percent in the multistages was obtained when either hydrogen or reformed natural gas was used as the reducing gas. Magnetic separation and concentration of the highly reduced fluid-bed product yielded a high metallic iron concentrate analyzing 85 percent total iron and 80 percent metallic iron with total iron recovery as great as 90 percent. Agglomeration of the high-grade metallized concentrate produced hard pellets analyzing 85 percent total iron and 78 percent metallic iron. Green pellets, with good strength, were made without any binder in a drum pelletizer. Direct melting of the high-metallic fluid-bed product in a basic lined arc furnace produced a nearly pure iron which contained 0.09 C and 0.01 P with 95 percent recovery of the metallic iron in the metal.

Jan 1, 1972

By Robert H. Ridgway

Chromite has been produced commercially for slightly more than a century. Developed, at one time, chiefly as a chemical pigment raw material, it has subsequently found extensive application in other chemical industries - as a refractory material for furnace linings and as the sole source of the metal chromium. For some years prior to 1914, its use as a refractory predominated; but post-war development in alloy steels, principally stainless steels, enhanced the metallurgical demand in the form of ferrochrome with a consequent increase in the demand for chromite. More recently direct reduction of chromite in alloy-steel manufacture has been applied to a limited extent. Alloy steels containing varying amounts of chromium, with or without other alloying elements, now find extensive use in a ride variety of ways - in structural material, machines, industrial equipment transportation by land, sea, and air, sanitary equipment, food preservation, and a multitude of other uses. In recent years chromium plating has had wide application and has become important. industrially, but the amount of raw material consumed

Jan 1, 1936

By Louis A. Panek

The practice of roof bolting or rock bolting to stabilize rock surrounding underground excavations has increased tremendously within a few years. This widespread application has led to many questions concerning the mechanics of bolting and has pointed up the need for a quantitative method of designing bolting systems. To answer these questions a research program was initiated to determine the principles of roof bolting. The first problem chosen for investigation was the use of bolts to reinforce bedded roof, since the great majority of bolts are used under these conditions. The attack employed is a combination of theoretical and experimental stress analysis. Centrifugal testing of models was chosen as the experimental method because it is particularly suited to the study of stratified roof. This report describes the models, the experimental method, and the model-prototype relations. By using dimensional analysis, a general expression for a roof-bolting design formula in terms of the structural variables has been obtained. Certain model-prototype similarity requirements have been relaxed, thereby minimizing the number of variables to be studied and extending the applicability of quantitative test data to a large class of full size structures.

Jan 1, 1956

By Ren G. Dong, Richard McCormick, Dan E. Welcome

Vibration exposure at workplaces is generally multi-axial. The health effects of vibration exposure also likely depend on the vibration direction. Therefore, there is a wide interest in the simulation of multi-axial vibration in laboratory experiments. Advances in technology have led to the development of a new 3-D test system for studying hand-transmitted vibration exposure and health effects. The purposes of this paper are to introduce the system and to present the results of its preliminary evaluations. Test System As shown in Figure 1, the system is basically composed of three vibration generators, a multi-axis vibration control system, instrumented handle, handle fixture, and shaker-fixture linkages (stingers). [ ] Figure 2 shows the array of three vibration generators (MB Dynamics, Energizer BLACK-500 lbs) and their associated support bases and foundation developed by MB Dynamics (Cleveland, USA), which create the 3-axis simultaneous motion. These electrodynamic exciters are powered by power amplifiers which provide current proportional to the analog drive signal from a controller. The controller (JAGUAR Multi-Input/Multi-Output closed-loop vibration controller) was provided by Spectral Dynamics, San Jose, California, USA). NIOSH-designed instrumented handle was equipped on the system.

Jan 6, 2006

By BUREAU OF MINES

A complete list of permissible mining equipment, rescue apparatus and gas masks tested prior to July 1, 1928, was published in Bureau of Mines Information Circular 60772. The present list includes practically all equipment tested and, approved by the Bureau, up to and including Jan. 1, 1929. It covers electric air compressors, coal drills, mining machines, loading machines, conveyors, mine pumps, room hoists, mine telephones, rock-dusting machines, switches, electric cap lamps, flame safety lamps, electric hand and trip lamps, flash lamps, methane indicators and detectors, blasting units, storage barrery locomotives, tandem locomotives, power trucks, concrete mixers, self-contained oxygen breathing apparatus and gas masks. The system under which those devices were tested permits the manufacturer, after his equipment has passed certain tests prescribed by the Bureau of Mines, to mark his equipment with a seal shoring that it has been "approved" by the Bureau. These tests are designed to insure that the equipment has the minimum requirements for safety in use. The only object of the Bureau in making such tests and pub- lishing lists of permissible equirment is to safeguard the lives of workers and to help lesson the hazards of mining.

Jan 1, 1929

A system to continuously measure the concentration of radon in mine ventilating air has been developed and tested in a uranium mine. In use, the air/radon mixture to be monitored is pumped through filters into a scintillation cell where nuclear decay of the radon produces flashes of light. These are electronically counted, giving a quantitative measure of the radon present. Air is continuously drawn from the mine atmosphere into the radon sensor box. This air sample passes through two filters into the detector cell as shown in the schematic diagram. A portion of the radon in the detector cell will experience nuclear decay, producing polomium 218 and an alpha particle. The alpha particles from the fraction that decays strike a zinc-sulfide coating on the inside wall of the cell and produce flashes of light. These enter a photo-multiplier tube which records each flash as an electrical pulse. An amplifier increases the voltage of each pulse, allowing electronic screening to remove noise and other undesirable pulses. The remaining pulses are counted by a conventional data acquisition system.

Jan 1, 1978

By John C. Holtz

The Bureau of Mines studied air contamination caused by diesel exhaust in a 10,000-ft ventilated tunnel. Sequential air samples were taken at the ends and middle of the tunnel during an operating cycle. Observed and calculated results for carbon dioxide, carbon monoxide, and nitrogen oxides were essentially in agreement. Nitrogen dioxide was present only in trace amounts. It was found that contamination was related to the volume of ventilating air, the number of haulage trips, train speed, and engine load.

Jan 1, 1968

By L. B. Berger

The Haldane gas-analysis apparatus used by the Bureau of Mines is patterned after the device developed by Haldane 4/ and differs from it only in structural modifications that have been added to facilitate operation and simplify construction. The apparatus was developed to permit determination of carbon dioxide, combustible gases, and oxygen with a degree of accuracy not attainable with apparatus of the types ordinarily used for the analysis of fuel gases, flue gases, and similar mixtures. The Haldane apparatus is used by the Bureau of Mines chiefly in the analysis of air samples collected in coal and metal mines and other underground workings and is applied also in the analysis of many other types of gas mixtures when accurate determination of certain constituents is desired.

Jan 1, 1938

By E. P. Youngman

The law of June 5, 1911, suplements and amends the Laws of April 21, 1810 (the basic law) and May 2, 1837. The Royal Decree of September 15, 1919, coordinates the provisions of the Law of June 5, 1911, with those of the Laws of April 21, 1810, of May 2, 1837, and of July 8, 1865, that have remained in force, as well as with certain articles of the Law of September 1, 1913, which revisad the system of taxation. The revised code has been brought together in one volume.3 All citations in this abstract refer to the coordinating Royal Decree of September 15, 1919, unless it is otherwise specifically indicated.

May 1, 1930

By Larry R. Wilson

The development effort described herein was directed toward the design and development of a flexible communication system to provide two-way section communications between any telephone on an MCM-101 telephone FDM exchange and a miner provided with a uhf walkie-talkie transceiver. The system also provides normal communication between miners within a working section through the uhf coupler interface repeater.

Jan 1, 1976

By J. Grumer

Nine dust and gaseous inhibitors of propagating coal dust-air flames (lean, stoichiometric, and rich) were evaluated in a newly developed 15-cm-id, 3.6-meter-long instrumented flame duct, under conditions such that wall quenching was virtually absent and the dust concentration was temporally and spacially uniform to within about t5 percent. Listed roughly in order of increasing efficiency, the inhibitors evaluated were rock dust (calcium carbonate), powdered oyster shells (calcium carbonate), Halon 1301 (trifluorobromomethane), Halon 1211 (difluorochlorobromomethane), sodium chloride, Super-K (potassium chloride), regular-grade fire extinguishant powder (sodium bicarbonate), Purple-K (potassium bicarbonate), and Monnex (potassium bicarbonate combined with urea). Experiments were extended to clouds containing 1 and 2 volume-percent of methane. The inhibition of lean, stoichiometric, and rich methane-air flames without coal dust was also examined in a few instances; results agreed with those obtained for coal dust-air flames.

Jan 1, 1971

By H. W. Kilau

The U.S. Bureau of Mines is evaluating water spray additives for the purpose of improving respirable dust control during coal mining operations, with particular emphasis on the longwall shearer. Recent field tests of surfactant-polymer reagents at two production longwall operations have shown favorable respirable dust reductions compared with water sprays containing no additive. Gravimetric dust samples obtained by a technician downwind of the shearer while following or preceding the machine showed dust reductions in the range of about 40% to 60% for some of the reagent formulations compared with using water alone. Three polymers were tested: two polyethylene oxide compounds of different molecular weight and hydroxypropyl methylcellulose (HPMC). All were effective for dust reduction, and two were cost effective when used in combination with sodium di(2-ethylhexyl) sulfosuccinate surfactant. How-ever, the use of these reagents requires the longwall operator to be more aware of headgate dust control. Experimental evidence indicates that dust captured by reagent-treated sprays at the shearer can be reemitted in the headgate area if stagcloader-crusher sprays and other dust controls are inadequate.

Jan 1, 2010

By W. M. Traver, A. M. Evans

"INTRODUCTION The Bureau of Mines undertook exploration in the Torlingua district, Texas, during June 1943, at a time when the demand for mercury for war industries was considerably more than the anticipated domestic production. In view of the impressive past production of the mines and the favorable geologic conditions in several underdeveloped areas in the district, the investigation was considered of immediate importance.Prior to initiation of the exploratory program, a preliminary examination of the district was made in August 1942 by A. B. Needham, an engineer of the Bureau of Mines. This examination was followed by a comprehensive geological study by the Federal Geological Survey 3/ and further investigation the Bureau of Mines."

Jan 1, 1947

By W. H. Ode

Because trade increased among various nations after World War II, the Coal Committee of the Economic Commission for Europe established a Classification Working Party in 1949 to develop an International system for classifying coal. Although national classification systems existed, they had been developed in accordance with characteristics of domestic coals without reference to coals of other countries. Terms for describing similar or identical coals differed in each nation. This caused confusion in evaluating coals shipped in international trade and also hampered exchange of technical information on problems of coal utilization. Experts4/ participating in the classification project early in their work agreed that two systems should be formulated, one for the higher rank coals or so-called "hard" coals in European terminology and the other one for the lower rank coals, the latter designated mainly as brown coals and lignites in the various countries. Rank refers to the degree of metamorphism (progressive alteration) in the natural coalification series from lignite and brown coal to anthracite. The system for classification of hard coals was published late in 1956 as a document of the United Nations.5/ Results of a study for applying this system to American coals were published in 1958.6/

Jan 1, 1960

By George K. Schenck

This Bureau of Mines publication describes and evaluates a Standard Industrial Classification (SIC) based end-use data system for minerals that is designed to link the demand for minerals to economic activity in commercial uses. The new data system is two-dimensional. The first dimension of technical product classes (TPC's) measures the consumption of minerals in major primary intermediate products. The second dimension measures the consumption of these TPC's in SIC end-use sectors in sufficient detail to identify the major determinants of demand for each TPC. Intercomodity comparisons are achieved at the level of SIC two-digit major groups. The methodology was developed so that all available sources of information from Government and industry can be utilized at minimum cost. This information will be supplemented with additional data to be obtained by modifying existing Bureau of Mines canvasses so as to elicit additional quantitative responses from mineral producers. The new data system is expected to improve significantly the ability to forecast demand for minerals, and provide an information base that would, for the first time ever, permit resolution of such questions as trends in substitution among materials and the intensity-of-use of materials in end-use sectors. For the 42 TPC?s identified in the report, data are available for the new system from current sources or, except for three TPC?s that require new canvasses, can be obtained by modification of existing Bureau canvasses.

Jan 1, 1982

By L. K. Weaver

The objective of this Bureau of Mines publication Is to present a nomograph that provides a fast, convenient method for estimating hydrocarbon lease bonus bids for offshore acreage in the Gulf of Mexico. Discounted cash flow analyses were computed from a model derived to show the costs necessary to explore, acquire, develop, produce, and abandon a 5,000-acre block of offshore acreage, and the estimated income from the sale of the hydrocarbons produced from the block. The range of the variables in the financial analyses used to construct the nomograph are prices of oil, $2.50 to $5.00; recoverable hydrocarbon reserves, 44,651,476 to 127,575,645 barrels; and discounted cash flow (DCF) rates of return, 5.0 to 57.2 percent. A total of 1,234 sets of DCF data were used to construct the nomograph. The range of bonus bids shown on the nomograph is from 2 to 90 million dollars ($400 to $18,000 per acre).

Jan 1, 1973

By Gary Friedline

As a consequence of the Coal Mine Health and Safety Act of 1969(PL91-173), the Bureau of Mines (BOM) entered into a contract with Ocean Energy Inc. (OEI) to develop, fabricate, install, and evaluate a permissible lighting system for use on a longwall coal mining operation. The program schedule is shown in Figure 1.1. The proposed regulations are contained in Appendix A. The initial part of the program involved a survey of existing longwall lighting practices in Germany and England and an evaluation of a variety of lighting components on a mockup of a longwall mining operation that was fabricated under this program. Visits made to German and British mines uncovered major differences in lighting level requirements, permissibility aspects, size, and operating constraints which identified wide disparities and essentially eliminated from further consideration any known imported lighting devices for meeting the higher lighting levels and standards proposed for US coal mines by the Mining Enforcement and Safety Administration (MESA). The longwall mockup provided use¬ful information regarding the amount of illumination required, physical size and shape of lamps, light distribution problems, cable routing, use of connectors, signaling, glare, and other important factors unique to the lighting of low coal longwalls.

Jan 1, 1975