Search Documents

By Laxman S. Sundae

A U.S. Bureau of Mines designed and fabricated in-seam tester (1ST), retrofitted with a dust shroud, was used to establish a respirable dust index (RDI) and to determine cutting forces from a variety of bit types in four coal mines and a salt mine. Results from cutting tests at four coal mines showed that radial bits required the lowest cutting force and the least specific energy. Generally, for each conical bit the RDI and cutting force increased when the included bit tip angles increased from 70° to 90°. During field tests it was not possible to measure the total quantity of respirable dust produced by each cut; therefore, attempts were made to determine the amount of dust that became airborne from each test cut. The test results show that the quantity of airborne respirable dust is very erratic and cannot be related to bit type. Two statistical methods were employed to analyze RDI, but no correlation was found between the RDI and bit type. Despite scatter in test results for RDI, significant difference was found in RDI generated in four coal seams. In general, RDI increased with the increased cutting force for each coal seam from mine 1 through mine 4.

Jan 1, 1989

By R. P. Beyer

[The Bureau of Mines has measured the low-temperature heat capacities and high-temperature enthalpies of crystalline K2Si2O5 as part of a program for advancing mineral resources technology with energy economy. High-temperature enthalpies of glassy and liquid K2Si2O5 and crystalline K2SiO3 were also mea¬sured. An adiabatic calorimeter operating over the range 5 to 308 K was used for the heat capacity measurements for K2Si2O5 from which the standard entropy at 298.15 K, S°298 = 45.55 ±0.05 cal/deg-mole, was calculated. Tabulated values of Cp°, S°, -(G° -HO°)/T, and H°-HO° from 5 to 300 K are given for K2Si2O5. A copper-block drop calorimeter was used in the enthalpy measurements, operating from 298.15 to 1,198 K for K2SiO3 and from 298.15 to 1,453.8 K for K2Si2O5. No transitions were found for K2SiO3. The KI2Si2O5 showed two reversible first order transitions, one at 510 K with a heat of transition of 0.29 kcal/mole and one at 867 K with a heat of transition of 0.38 kcal/mole. The heat of fusion for K2Si2O5 20 5 was calculated to be 8.42 kcal/mole. Relative enthalpies are given in equation form, and high-temperature values are tabulated for Cp°, S°, - (G°-H°298 )/T, and H°-H°298 . Also tabulated are ?H°, ?G°, and log K for formation of K2SiO3 and K2Si2O5 from both the elements and the oxides.]

Jan 1, 1979

By Martin H. Stanezyk

The Bureau of Mines investigated leaching of selected copper sulfide minerals and a composite of impure flotation concentrates at elevated temperatures and pressures with ammoniacal solutions. Copper 1 (tractions of 96 percent were obtained by leaching chalcopyrite at 75° C under oxidizing conditions for 60 minutes. An extraction of 99 percent of the copper contained in the composite concentrate was obtained by leaching the product for 90 minutes at 75° C. In tests of bornite, chalcocite, and covellite, 90 to 97 percent of the copper was extracted at 20° C provided an 8-hour reaction period was used. At 75° C essentially complete dissolution of the copper from these three minerals was accomplished in 60 minutes. Additions of ammonium sulfate to the leach solutions were required to obtain high-percentage extractions of the copper from bornite, chalcocite, and covellite. Although ammonium sulfate was not required when digesting chalcopyrite, copper extraction was enhanced and less free ammonia was required when ammonium sulfate was added to the leach pulps. The chemistry of leaching copper minerals was studied. It was C, termined that chalcocite altered to covellite as one step in the dissolution When leaching iron-bearing copper sulfides, hydrated iron oxide formed on the mineral surfaces, indicating that a diffusion process prevailed. No evidence of covellite was detected.

Jan 1, 1966

By Terry S. Cory

This report describes a complete system design methodology for medium frequency (MF) wireless radio systems for use in coal mines. The emphasis Is on AC mines where no trolley wire exists and, for which, conventional trolley phone communications can not be used. The report constitutes an MF system design handbook and includes a compendium of all previous MF technology elements as well as a reference Index with abstracts of all pertinent literature. A particular strawman system design analysis is Included for the Helvetia Coal Co. Lucerne #8 mine In the Upper Freeport seam.

Jan 1, 1979

By Wilton Johnson

The development and use of minerals and mineral fuels are essential to national security and to the maintenance of an expanding economy. As a Nation, we often met these needs but failed to recognize and assess the impact that mining and mineral processing activities have on other natural resources. Currently, the growing demand for energy and minerals is accompanied by an increasing awareness that the provision of these resources must not conflict with society's demand for a clean and habit-able environment. Although present mining and mineral processing activities incorporate, or have under development, technology capable of minimizing environ-mental impacts on land, air, and water, many older operations, particularly in the first half of this century, lacked the technological, social, and environmental insights that exist today. Consequently, a substantial backlog of damaging and potentially damaging conditions remains from such problems as mine subsidence, acid water generation, burning and nonburning waste banks, abandoned surface-mined lands, abandoned underground mine fires, and abandoned mine shafts and oil and gas wells.

Jan 1, 1979

By Jeffrey Shawn Peterson

Among underground coal miners, hearing loss remains one of the most common occupational illnesses. In response, the National Institute for Occupational Safety and Health (NIOSH) conducts research to reduce the noise emission of various underground coal mining equipment, an example of which is a roof bolting machine (RBM). After the removal of coal or rock, the remaining strata may be subject to fall, either from overhead (the roof) or from the side (the rib). One method used in underground coal-mines to prevent failures requires the installation of roof bolts. The roof bolting machine operator trams the machine to the required location, drills a hole into the strata, and then installs a roof bolt, supporting the roof or the rib, as the case may be. Field studies support the premise that, on average, drilling noise is the loudest noise that a roof bolting machine operator would be exposed to and contributes significantly to the operators? noise exposure. NIOSH has determined that the drill steel radiates a significant amount of noise during drilling. NIOSH is developing bit and chuck isolators to reduce vibration, and thus noise radiation of the drill steel, with the longer-term goal of reducing roof bolting machine operator noise exposure. Laboratory testing has shown that operator ear sound pressure levels may be reduced by 3 to 7 dB(A), depending upon the test configuration and drilling media.

Jan 1, 2009

By Thomas E. Green

A combined solvent extract ion-spectrophotometric method for the determination of as little as 1 ppm of copper in tungsten metal or tungstic oxide has been developed and evaluated. Metallic samples are converted to tungstic oxide by treatment with hydrofluoric and nitric acids. The oxide is then dissolved in sodium hydroxide, and the copper is extracted as the colored neocuproine complex. Total elapsed time for the analysis is approximately 1-1/2 days; however, actual working time for a group of six or eight determinations is less than 4 hours. Precision at the 2-ppm level is better than 0.1 ppm.

Jan 1, 1963

By David C. Oyler

The Bureau of Mines is cooperating with the U.S. Department of Energy in a directional degasification project at the Emerald mine near Waynesburg, Pa. This project is designed to combine the highly successful underground horizontal degasification technology with surface drilling methods. The objective of this program is to demonstrate that directional drilling can be used as a technique for degasifying coalbeds ahead of mining to reduce the hazards of methane-air explosions in coal mines. The directional hole at the Emerald mine is designed to start vertically and enter the Pittsburgh coalbed horizontally. A 3-inch-pilot hole entered the Pittsburgh coalbed at a vertical depth of 999 feet. The hole will be reamed to 8-3/4 inches in diameter, and 5-1/2-inch casing will be cemented in place. Three individual 3-inch-diameter, 3,000-foot horizontal gas collection holes will be drilled into the coalbed in a "bird foot" pattern. A corehole and vertical dewatering hole have been completed at the anticipated coalbed intercept. The dewatering hole was drilled to 130 feet below the Pittsburgh coalbed, a depth of 900 feet, and 880 feet of 7-inch-OD casing was cemented in place. Seven vertical holes for monitoring the extent and progress of degasification have been drilled within the horizontal drilling area.

Jan 1, 1979

By Terry S. Cory

This report describes a complete system design methodology for medium frequency (MF) wireless radio systems for use in coal mines. The emphasis Is on AC mines where no trolley wire exists and, for which, conventional trolley phone communications can not be used. The report constitutes an MF system design handbook and includes a compendium of all previous MF technology elements as well as a reference index with abstracts of all pertinent literature. A particular strawman system design analysis is included for the Helvetia Coal Co. Lucerne #8 mine in the Upper Freeport seam.

Jan 7, 1979

By G. S. Scott

The flammability of trichloroethylene vapors in air has been determined in a 7-inch cyclindrical vessel. Saturated flammable mixtures were formed with air at atmospheric pressure between 30° C (86° F) and 82° C (180° F); the trichloroethylene concentrations at these temperatures are 12.5 (lower) and 90 (upper) volume-percent, respectively. Further study is necessary to assess the effects of different variables on the flammability of this material. INTRODUCTION Trichloroethylene (TCE) (ClHC = CCl2), sold under various trade names (Blacosolv, Perm-A-Clor, Tri, Triad, Triclene, Trivec, Tromex, Vapoclean, Vapoclor, Westrosol, etc.), is an important industrial chemical. A summary of its physical and chemical properties is given in table 1. It is used to degrease metals, leather, and textiles, to extract residual oils from vegetable oil cakes, for dry cleaning, and in soap. It is a powerful solvent for fats, resins, bitumens, rubber, sulfur, and phosphorus. Several explosions in which trichloroethylene was involved prompted an investigation by the Bureau of Mines to determine the conditions under which such accidents can occur.

Jan 1, 1963

By G. W. Jones

In a previous report'/ results were given and a method outlined whereby from a knowledge of the composition of the natural gas and of the inflammability limits of the individual constituents composing the natural gas, the limits of inflammability of natural gas and air mixtures could be closely calculated. This method is based on the application of Le Chatelier's law as modified by Coward, Carpenter and Payman,5/ to apply to a mixture of any number of combustible gases. This law must not be used indiscriminately, because many exceptions have been found. For example, when ethylene, acetylene, hydrogen sulphide, or chlorinated hydrocarbons are present the law may not hold. For a discussion of the many exceptions which have been found, reference should be made to a report by Coward and Jones.6/

Jan 1, 1933

As mining operations in the United States (US) have become more productive, controlling the dust exposure of mine workers has become more challenging. In response, US mining operations are applying basic controls at elevated levels and are looking to emerging control tech­nologies in an effort to better control airborne respirable dust levels. The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) conducts research to develop and/or improve control technologies that reduce the respirable dust exposure of workers in underground coal mines. The goals of this research involve optimizing the use of water sprays and ventilating air, as well as, evaluating emerging control tech­nologies. An overview of dust controls typically utilized in underground US coal mines will be provided. An update on ongoing PRL research efforts that are evaluating new control technologies will also be presented.

Jan 1, 2008

By d&apos, D. V. Andrea

Nine rock properties were determined for rocks coming from 49 locations and having a wide range of compressive strengths. Plots of the nine rock properties versus each other were prepared. A stepwise multiple linear regression analysis was performed to obtain several equations for predicting compressive strength. Both linear and curvilinear relationships were assumed between compressive strength and the other rock properties. The prediction equations had multiple correlation coefficients ranging from 0.947 for an equation with 1 variable (point load tensile strength) to 0.986 for an equation with 25 variables. Of the properties tested only point load tensile strength could be used alone to estimate compressive strength with fair accuracy.

Jan 1, 1965

By Richard D. Hagni

The character of phosphorous-bearing minerals in the Birmingham red Iron ores and iron-bearing minerals in the Eufaula bauxite deposits in Alabama has been Intensively studied by petrographic, ore microscopic, luminescent microscopic, scanning electron microscopic, electron microprobe, and x-ray diffraction techniques. A total of 15 types of phosphorous-bearing mineral grains have been recognized in Birmingham iron ores by their characteristic sizes, shapes, and distributions. Size measurements, modal analyses, and texture analyses have permitted an estimate of potential liberation of phosphorous from the iron ores by beneficiation to be 27% In areas of previous mining and 60% in areas of current iron reserves. Fine grinding, selective flocculation, and flotation may constitute the best beneficiation technique for future research. Hematite and goethite are the most important iron minerals in Eufaula ferruginous bauxites, but pyrite, marcasite, and siderite are Important iron minerals in some varieties of ferruginous bauxite, and lepidocrocite and ilmenite occur locally in minor quantities. Although simple screening will remove the coarsest iron-bearing grains, research on the utilization of high gradient magnetic separation to reduce the amounts of iron-bearing grains is recommended.

Jan 1, 1981

By E. G. King

Low-temperature heat capacity determinations of the minerals goethite and pyrophyllite were made in the temperature range from 510 to 298° K. The entropies at 298.15° K were evaluated as 14.43 ±0.15 cal/deg mole for goethite and 56.6 ±0.5 cal/deg mole for pyrophyllite. The entropies of formation from the constituent oxides are -4.4 ±0.2 cal/deg mole for goethite and -12.3 ±0.6 cal/deg mole for pyrophyllite. The standard free energy of formation of goethite from its oxides is ?G°298.15 = 0.16 ±0.20 kcal/mole.

Jan 1, 1970

The strike of the Canadian asbestos miners entered its seventh month with increasing signs of early termination. Both unions are in the midst of heavy negotiations with management, and an optimistic industry source predicted that work would resume by October 1. Recession recovery in some segments of the asbestos manufacturing industry is being impeded by lack of fibers, CADMIUM - On September 9, St. Joe Minerals Corp. reduced the price of cadmium metal to $2.75 per pound. The producer price bad been uniformly quoted at $3.00 per pound since June 26, 1975. Subsequently, Amax, Inc. and National Zinc Co. reduced their prices to $2.50 per pound. By mid-September all five U.S. cadmium producers were marketing the metal at $2.50 per pound.

Jan 1, 1975

By Welton J. Wenger

Apparatus for the analytical distillation of crude oils under an artificial pressure of 760 mm. of mercury has been designed and constructed. This apparatus enables laboratories at high altitudes to make Bureau of Mines routine analyses of crude oils with results similar to those obtained by laboratories at sea level. This is especially important for laboratories in the Rocky Mountain region, where barometric pressures of approximately 600 mm of mercury are encountered. During the past 30 years, the ?Bureau of Mines has made several thousand analyses of crude oils from various parts of the United States and from foreign countries. The first part (stage 1) of the distillation for the analysis is made at atmospheric pressure, and as most petroleum laboratories are near sea level, comparable results are obtained ordinarily. However, the increased use of the method by .laboratories at high altitudes has caused difficulty, as the analyses cannot be accurately compared with analyses from laboratories at sea level. For instance, laboratories at 7,200 feet generally report 2 to' 4 percent (based upon the crude oil) more gasoline than sea level laboratories. The use of the pressurized apparatus developed by the writers makes it possible for these high-altitude laboratories to duplicate analyses made at sea level.

Jan 1, 1949

By S. C. Schaefer

The Bureau of Mines investigated tIle standard Gibbs energies of formation, 8Gfo, for MllF2 (manganese difluoride) and CoF2 (cobalt difluo-ride). High-temperature galvanic cells employing CaF2 (calcium diflu-oride) as the solid electrolyte were used to measure the open-circuit potentials for the cell reactions ?

Jan 1, 1985

By A. B. Campbell

The mines in the eastern part of the now active region of the Tri-State zinc district of Missouri, Kansas, and Oklahoma have unusually acid water, which during periods of moderate or no rainfall is used in the mills to replace losses from evaporation, seepage-, and tailings disposal. Its use has caused difficulties by corrosion of equipment and by interference with flotation. The growing importance of flotation, which requires good water, and the increasing troubles caused by the corrosion of the milling equipment have prompted the Mississippi Valley Experiment Station of the United States Bureau of Mines, in cooperation With the Missouri School of Mines and Metallurgy, Rolla, Mo., to investigate the action of the waters on flotation and to undertake to develop means of obviating their harmful effects. The work was under the immediate direction of W. T. Schrenk, consulting chemist, United States Bureau of Mines, and professor of chemistry Missouri School of Mines and Metallurgy, and. Will H. Coghill., supervising engineer of the ore dressing section of the United States Bureau of Mines.

Jan 1, 1932

By Donald A. Voigt

This publication is intended as a guide for persons responsible for obtaining classifications and approvals Tor explosive compounds, mixtures, or devices from the U.S. Department of Transportation (DOT). It deals with the procedures for obtaining a recommendation for classification of an explosive compound, mixture, or device through the Bureau of Mines. Completion of the procedures detailed in this guide is necessary to obtain a final classification of an explosive compound, mixture, or device and assignment of an "EX" number by DOT, which will allow the producer to offer the explosive for shipment within the United States. This guide also gives procedures for obtaining United Nations (U.N.) classification for shipping outside the United States.

Jan 1, 1990