Search Documents

By G. R. Hopkins

The average quantity of heat needed to refine a barrel of crude oil in 1934 was 638,000 B.t.u., or about as much heat energy as contained in 5 gallons of fuel.oil. Although the total heat utilized in 1934 was slightly above 1933, crude runs to stills increased 4 percent, hence the average requirement per barrel declined from 660,000 B.t.u. in 1933 to 638,000 B.t.u. in 1934 (see fig. 1). The average for 1934 constitutes a new record for firing efficiency, being just under the previous low of 1929. Heat consumption at refineries depends on many factors, of which the trends in yields of gasoline and lubricating oils are probably most important. The yield of gasoline is indicative of activity at cracking plants, which typo of plant utilizes more thou the average amount of heat per gallon of product. The yield of lubricating oils is indicative of the extent to which crude oil is refined; that is, it takes considerably more heat to refine a barrel of crude through lubricating oils than it does to separate only gasoline and kerosene. The yield of gasoline decreased from 43.7 percent in 1933 to 43.4 percent in 1934; on the other hand, the yield of gas oil and fuel oil increased. Although the yield of lubricating oils increased slightly in 1934 the theoretical increase in fuel requirements probably was offset by technical improvements, such as solvent refining. Although no outstanding technical developments of a fuel-saving nature were made in 1934, some progress undoubtedly was recorded. Heat exchangers, an effective fuel-saving device, wore enlarged, and some refiners now take off several cuts before the crude reaches the pipe stills. The total capacity of pipe stills increased 2.5 percent in 1934, and many of the less efficient shell stills were torn out.

Jan 1, 1935

By A. F. Colombo, D. W. Frommer

Bench- scale tests were made to determine the applicability of flotation as a means of upgrading finished and semifinished magnetic concentrates prepared from reductively roasted iron ores . Both anionic and cationic flotation methods were used to remove siliceous gangue from the magnetic concentrates and produce upgraded products . Seven magnetic concentrates , containing from 6.7 to 13.7 percent SiO2 , were improved by the flotation treatment , yielding final concentrates containing less than 6.0 percent Si02 . Cationic flotation methods were studied on four of the seven samples ; of this group only one sample yielded better results by cationic flotation than by the anionic method .

Jan 1, 1964

By C. N. Adams

The purpose of this investigation was to evaluate the physical and mechanical properties of high-purity titanium made by two processes. Sodium-reduced metal with 58 Brinell hardness number (B.h.n.) and electrorefined metal with 60 B.h.n. and 70 B.h.n. were used. Titanium of these hardness levels did not work-harden excessively, and beyond 40 percent cold work the hardening effect was not great. Rapid softening occurred when the metal was annealed at temperature between 300° and 600° C. Full annealing, as determined by property and microstructure studies, was accomplished after 30 minutes at 700° C. A recrystallization diagram is presented which is based on determinations of annealed grain size as a function of rolling reduction and annealing time. For reductions of less than 20 percent, exaggerated grain growth occurred during annealing; for reductions greater than 20 percent, the variation in grain size for each annealing temperature was minor.

Jan 1, 1961

By J. M. Mutmansky

"This study analyzed laboratory comminution techniques for respirable mine dust generation and the properties of the resulting dusts. It was the objective of the study to determine the suitability of the resulting dusts in reflecting the properties of natural airborne dust. This paper deals specifically with the amount of contamination introduced into the generated dust as a result of abrasion when using nine different grinding methods. The analysis was made by comparing the content of 25 chemical elements in the lab-generated dusts with the same elements in the airborne coal mine dusts. It was found that all the lab-generated dusts possessed contamination but that several methods produced smaller percentages of contamination and that the residence time in the grinding device was an important factor in the contamination levels. INTRODUCTIONDust in the atmosphere is a health hazard and a major source of occupational diseases in the coal mining industry (Anon., 1980; Merchant, Boehlecke, and Picket-Hamer, 1986). It has been shown that coal workers' pneumoconiosis (CWP) is directly related to the inhalation and accumulation of respirable coal dust in coal miners' lungs. In order to effectively protect coal workers from coal dusts, we must have a clear understanding of dust properties including dust generation and dust-lung reaction mechanisms. This requires extensive biomedical research. Dust related research often requires large samples of respirable coal dusts to be collected, either for repeated experiments or stored for future reference. Unfortunately, current sampling instruments are not able to meet this demand. Ali a result, laboratory-generated coal dust ls frequently used as a substitute for coal mine dust in biomedical and other research applications. Now, the questions are how close the characteristics of laboratory-generated dusts are to those of mining-generated dusts and which equipment is moat appropriate for research dust production in the laboratory . These are some of the interests of this research project. The primary objective of this project was to find a laboratory technique which can generate coal dusts possessing properties similar to coal mine dust with respect to particle size distribution, chemical composition, and particle shape and morphology. However, this paper will focus only on the chemical compositions of the prepared dust samples and try to identify the sources of chemical contamination from various size reduction processes."

Mar 1, 1992

By Summer S. Smith

The year 1916 broke all previous records of mineral production in the Territory. As a consequence, there has been a noteworthy increase in the number of mines in active operation or under development, though the greater part of the increased output is the result of greater activity at mines already producing rather than of opening new mines. Owing to available funds not being sufficient to meet the cost of travel in the interior of the Territory during the winter months, the Federal mine inspector was unable during the spring to visit the placer mines of the interior as has been his custom in the past. However, by working in close cooperation with the Territorial in- spector, who left Juneau in June to take the first boat down the Yukon to Fairbanks after the spring break-up, it was possible to visit hurriedly all the larger mining centers of the Territory. The Territorial inspector covered the districts from Fairbanks to Nome and the Federal inspector covered those of southeastern and south- western Alaska. A number of applicants have begun mining coal on ground held under free-use 10-acre permits, and have furnished coal for local use. The larger leasing units in the Bering River and Matanuska coal fields have been advertised and applications for leases have been submitted. These applications came too late in the fall for active development to begin before the end of the year. The Government railroad has been built from Anchorage to the center of the Matanuska coal field, and private interests have under- taken the building of a standard-gage road from a point known as Goose City on Controller Bay to Canyon Creek, in the Bering River field. Capital has become interested in the oil fields on Controller Bay, and plans have been made for more active exploration and production. The work of the Federal mine inspector is still handicapped by the lack of funds for additional field assistants and of the office ac- commodations necessary for carrying on the work with the efficiency that its importance warrants.

Jan 1, 1917

By E. D. Gardner

"The Bureau of Mines has studied blasting practices in metal mines of the Southwest. The investigation of blasting drift rounds showed among other results, that cut-holes in ground difficult to break could be chambered to advantage under some conditions.In open--cut mines, chambering nearly all holes before blasting is the common practice. Two or more free faces are generally maintained in this type of work, and the amount of explosive necessary to break any bench or bank can usually be estimated from the yardage to be moved. However, in blasting drift or tunnel rounds only one free face is available before the cut-holes are shot, and the quantity of explosive required is generally ascertained best by trial.In addition to being the most difficult to break, the cut-holes are the most important of a drift round. When the cut-holes ""break bottom"" less work is required of the other holes, and a full break of the round is generally obtained. In ground difficult to blast, extra care and expense are justified to insure that the cut-holes ""break bottom.""At many mines the work is so organized that all blasting is done at the end of the shift, and a decided advantage would have to be gained to make chambering of the cut-holes economical. Also, in many mines blasting during the shift would not be practical. One or two holes could probably be drilled during the time necessary to do the chambering. However, under certain special conditions, such as in small operations or those where ""leasers"" or contractors are working, drill holes could be chambered should there be an advantage in doing so. Moreover, in some mines it might be practical to chamber the cut-holes at the lunch hour. In ordinary rounds the cut-holes are generally drilled by noon. It would not be necessary to tear down the drill or remove tools from the face to do this work of chambering."

Feb 1, 1928

By G. R. Hopkins

The average quantity of heat needed to refine a barrel of crude oil in 1934 was 638,000 B.t.u., or about as much heat energy as contained in 5 gallons of fuel oil. Although the total heat utilized in 1934 was slightly above 1933, crude runs to stills increased 4 percent, hence the average requirement per barrel declined from 660,000 B.t.u. in 1933 to 638,000 B.t.u. in 1934 (see fig. 1). The average for 1934 constitutes a new record for firing efficiency, being just under the previous low of 1929. Heat consumption at refineries depends on many factors, of which the trends in yields of gasoline and lubricating oils are probably most important. The yield of gasoline is indicative of activity at cracking plants, which type of plant utilizes more than the average amount of heat per gallon of product. The yield of lubricating oils is indicative of the extent to which credo oil is refined; that is, it takes considerably more heat to refine a barrel of crude through lubricating oils than it does to separate only gasoline and kerosene. The yield of gasoline decreased from 43.7 percent in 1933 to 43.4 percent in 1934; on the other hand, the yield of gas oil and fuel oil increased. Although the yield of lubricating oils increased slightly in 1934 the theoretical increase in fuel requirements probably was offset by technical improvements, such as solvent refining.

Jan 1, 1935

By James L. Eirls

Tracor MBA under a contract to U.S. DOI Bureau of Mines designed, developed, fabricated and demonstrated a conveyor belt service machine. It is self-contained, battery powered, rubber tired and capable of handling, storing and transporting conveyor belting, wire rope and associated structures for sectional conveyor belts. While moving the tail section to its next position the machine discharges the belting, wire rope and belt structures. The belting is elevated and separated to provide for the insertion of the structures with minimum expended effort. A hydraulic system provides the power for steering, braking, winding or unwinding under controlled tension the belting and wire rope, operating a load-bed slat conveyor, raising, lowering and locking connection hitches and powering external hydraulic tools. Also, a pneumatic system is available to operate air impact tools. The service machine, with its present components can function in coal seams as thin as 48 inches, double wind conveyor belting 42 inches wide, 400 feet long, load or unload 3/4" wire rope on two separate reels and is controlled by two operators. A complete belt move using this machine requires only four workers. Successful underground demonstrations were conducted in coal mines located in West Virginia and Kentucky.

Jan 1, 1983

By E. Morrice

As part of its efforts to maximize process efficiency and decrease energy requirements in mineral processes, the Federal Bureau of Mines has investigated methods for beneficiating bastnäsite ores from Mountain Pass, Calif. The results of a bench-scale study on the flotation of bastnäsite ore are presented. Flotation at a pulp temperature of 40° to 45°C yielded a cleaner concentrate containing 58.7 pct RE203 at a rare-earth recovery of 67 pct. These results are comparable to those reported for the commercial beneficiation method in which the pulp is heated to boiling before flotation. An attempt was also made to recover a barite flotation concentrate from the bastnäsite rougher tailing. Concentrates containing only 70 pct barite were obtained.

Jan 1, 1982

By Douglas F. Scott

Zinc, silver, copper, and tungsten are the principal minerals in Dardanelles RARE II area (No. 4982). Zinc with associated silver and copper occurs in a persistent shear zone in metasedimentary rocks and in a massive sulfide vein; tungsten occurs as disseminated scheelite in a tactite zone along a metasedimentary-intrusive rock contact. Since 1883, approximately 100 lode mining claims have been recorded, mainly it the eastern portion of area No. 4982 (fig. 1). Extensive workings on the Alhambra Prospect indicate past production; however, no records were found for the prospect. At the Alpine Mine, 500 tons of tungsten ore had been mined before 1943 (Hopson, 1943, p. 1) and possibly 1,000 tons of tungsten ore mined by 1947 (Benson, 194/, pp. 2).

Jan 1, 1982

By C. M. Frost

The hydrodesulfurization characteristics of a residual fuel prepared from Wilmington, Calif., crude oil were determined at temperatures from 600° to 900° F, pressures of 200 to 800 pSig, and space velocities from 0.2 to 2.0 Vo/Vc/hr, using cobalt molybdate type catalysts. A prediction equation, developed from the experimental data, satisfactorily predicts the fraction of total sulfur that can be removed under any combination of operating conditions within the ranges investigated. Yields and properties of the low sulfur product are correlated with the fraction of total sulfur removed. Kinetic calculations show that the apparent reaction order and activation energy change with space velocity and temperature.

Jan 1, 1970

By Richard G. Burdick

This Bureau of Hines report describes an interface between a minicomputer and peripheral device, The logic used to develop the device is discussed briefly, after which the device is described in detail; complete construction and operational details are given. The report should aid both in duplicating this device and in designing similar devices for different uses.

Jan 1, 1975

By S. H. Katz, J. J. Bloomfield

In studies of mine and tunnel ventilation conducted by engineers of the Bureau of Mines , various smokes are used to determine flow of air , direction of the currents , and the rate of mixing . The instrument for generating streams of sulphur trioxide (SO ) smoke , shown in the drawing herewith, has been found helpful , convenient and practicable for such purposes ; it is also especially useful in some places where fire for generating smokes is not permissible . The apparatus consists simply of a glass tube containing fuming sulphuric acid on granular pumice stone , attached to a rubber syringe bulb . When a squeeze of the bulb blows air through the tube , a stream of dense white smoke evolves, which follows and makes visible the air currents . The tubes after preparation are hermetically sealed to prevent deterioration . When ready for use , they are easily broken open at a file scratch for the purpose on both tips , and inserted into a rubber nipple at the bulb . Sometimes it is of advantage to attach them to a longer rubber tube leading to the bulb . Tubes of the size shown (about 1/2 inch outside diameter by 5 inches long) are usually sufficient for the needs of a day . Thereafter they cease to fume because the acid absorbs moisture from the air and looses its effectiveness . Smaller sizes of tubes and larger have been made , but the size shown has proved most practicable . Immediately after a person has finished using a tube it should be buried or disposed of in a place where it will not be touched by shoes or clothing, or come in contact with wooden floors , furniture , or metals , because the acid , which will eventually leak from the tubes , is highly corrosive . -- Reports of Investigations , Department of the Interior , Bureau of Mines .

Jul 1, 1923

By L. A. Stinnett

An investigation of hazardous surface openings of abandoned and inactive underground mines in the Black Hills area of South Dakota has revealed: (1) tracing legal ownership of mineral claims via county courthouses is confusing, complex, and oftentimes misleading, (2) in general, the selected mine openings in this investigation are to be considered relatively high in risks and hazard potential which poses a threat to the general public, (3) mine closure procedures and designs can generally be categorically implemented depending on the overall situation of the particular mine opening with subsequent unit costs estimates, (4) few preventive state or federal legal measures exist to date concerning mine closures, and (5) liability damages relating to mine opening accidents usually involve expensive and complex common law cases.

Jan 1, 1979

In attempting the predict coal cleat orientation in the subsurface for effective methane degasification of the coal beds in the Warrior coal field of Alabama, approximately 150 rock joint orientations and 45 coal cleat orientations were measured in each of 37 7 ½ minute quadrangles in Tuscaloosa, Walker, Jefferson, Fayette, Winston, Blount, and Bibb Counties. Data from these surface locations, and coal cleat data from eight underground mines was corrected for magnetic declination and titled beds rotated to the horizontal where necessary and plotted on rose diagrams for comparative analysis. Data collected on each joint and cleat consisted of attitude, quality, type, spacing, persistence, lithology, bedding thickness, surface texture, and filling. File data and published and unpublished reports from the State Survey and the State Mine Inspector's Office were re-viewed. Twenty-seven mining companies, most of which supplied information pertinant to the project were also contacted. The information obtained consisted of crop line information structure, and underground mine outlines, all of which were put on 7 ½ -minute topographic quadrangles. LANDSAT-1 imagery and Skylab photography were compared to dominant joint and cleat trends in the study area. Detailed results can be found in an open-file report entitled "Fracture Analyses in a Selected Area of the Warrior Coal Field, Alabama." A master's thesis entitled "The Relationship Between Surface Joints and Subsurface Structure in a Selected Area of the Warrior Coal Field" is being prepared to illustrate the relation-ship of the fracture system to the structure in the Warrior coal field. A proposal has been submitted for research on a project entitled "Rock Fracture Systems and Their Affects on the Extraction of Fossil Fuels in the Warrior Basin, Alabama"

Jan 1, 1976

By L. M. Demers, R. E. Edelson, M. P. Rose, D. T. Superdock

The pulmonary alveolar macrophage is a major defensive cell which counteracts the invasive properties of bacteria and particles when these substances invade the pulmonary environment. Pulmonary exposure to coal dust particles is believed to activate these macrophages to release a host of d1emical mediators which can neutralize or contribute to the harmful effects of these dust particles. Our efforts have been concerned with assessing a specific family of mediator substances produced by the alveolar macrophage from arachidonic acid when these cells are in contact with activating substances such as coal dust. Metabolites of arachidonic acid produce a vast array of effects which can impact significantly on pulmonary function both with normal pulmonary events and with pathologic processes of the lung. Our studies demonstrate that isolated alveolar macrophages obtained from rats or guinea pigs cultured in vitro release appreciable amounts of the cyclooxygenase products prostaglandin E2 and thromboxane A2 and release significant amounts of the lipoxygenase products .5-HETE and LTB4. In the presence of l x 104 -1x10·7 g/ml of a coal dust suspension, alveolar macrophages from the rats and guinea pigs alters their pattern of arachidonic acid metabolite release. In the rat, exposure of alveolar macrophages in vitro to the higher concentrations of coal dust causes a significant reduction in PGE2, TXB2 and LTB4 in a 4 hour time course study. In contrast, macrophages from the guinea pig in response to coal dust had little change in TXB2 release, only a slight inhibition in PGE2 production and an initial stimulation in LTB.t release over the 4 hour time course. Cells from guinea pigs released considerably more TXB2 than the rat under these conditions while rat cells formed considerably more LTB4 than guinea pig alveolar macrophages. These findings support the following conclusions.

Mar 1, 1989

By D. D. Fischer

Recovery and separation of molybdenum and rhenium from a process solution was accomplished by a technique developed by the Federal Bureau of Mines involving a combined solvent extraction and activated carbon adsorption procedure. The processing sequence required treatment of the solution with S02 to reduce the chlorate ion and adjust the pR prior to solvent extraction of molybdenum and rhenium with a tertiary amine. Molybdenum and rhenium were stripped from the organic phase with an NH40H solution, and the strip solution was then passed through activated carbon to preferentially adsorb the rhenium. After washing entrained molybdenum from the column with a brine solution, rhenium was eluted with an MeOH-H20 mixture. The activated carbon was regenerated with water. Molybdenum was recovered as (NH4)6Mo7024 by evaporating the column effluent. Rhenium in the column eluate was reextracted with a tertiary amine, stripped from the organic phase with dilute NH40H, and recovered as NH4Re04 by evaporating the strip solution. The final (NR4)Re04 product contained < 80 ppm impurities. Sodium sulfate was crystallized from the first solvent-extraction raffinate by lowering the solution temperature to 0° C. Precious metals contained in the original process solution were adsorbed onto the activated carbon.

Jan 1, 1975

By W. A. Calhoun

Progress made in a second and final metallurgical investigation made by the Bureau of Mines of near-surface Hawaiian bauxitic deposits from Kauai, Maui, and Hawaii Islands, and on a deeper deposit from Kauai, is reported. Previously reported Al2O3 extractions were increased by modifying conventional processes to fit the ore being tested. Increases in Al2O3 extraction were: Kauai, from 82.8 to 95.4 percent; Maui, 85.5 to 94.1 percent; and Hawaii, from 79.5 to 86.4 percent. Use of a "caustic-reduction sinter, leaching, and magnetic separation process" for Al2O3 extraction also produced an iron concentrate of commercial grade, except for titanium content. No successful method was developed for the recovery of a satisfactory titanium concentrate.

Jan 1, 1967

By Michael S. Miller

In 1987, 1988 and 1989, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the Sperry Creek Wilderness Study Area (OR-003-035; 5,600 acres) and the Gold Creek Wilderness Study Area (OR-003-033; 13,600 acres), plus an additional area (OR-003-033; 2,180 acres) adjacent to the Gold Creek Wilderness Study Area. The wilderness study areas and the addition are south of the Malheur River and are about 20 miles east of Juntura, Oregon. The wilderness study areas and the addition are underlain by volcanic rocks, predominantly basalt and rhyolite flows, breccias, and welded ash-flow tuffs. Lacustrine deposits containing diatomites occur mainly at the east side of the Gold Creek Wilderness Study Area and addition. Alluvium lies along the Malheur River, in terraces and fans south of the Malheur River, and along the floors of some creeks. Shear zones and faults have offset the rocks and provided channels for eruption of volcanic rocks and epithermal mineralization by hot springs.

Jan 1, 1989

By Jay F. Colinet, John A. Organiscak

In This Chapter [Which dust source to address first How much air and water are needed Keeping dust out of the walkway Moving workers upwind Dealing with the stage loader-crusher Gob and wing curtains to aid airflow The shearer-clearer system Modified support movement practices and Dust control for future longwalls ] Controlling longwall dust is not easy. Longwall production levels are high, and there are several different sources of dust to contend with. If dust levels are high, the initial effort should be devoted to finding which source is the cause. Then, efforts to reduce dust can be concentrated where they will have the most impact. To control dust at longwalls, a large amount of ventilation air and spray water must be used. The water must be sprayed correctly so as not to blow dust into the walkway. Techniques to change local airflow patterns can be helpful. The shearer-clearer, as well as gob and wing curtains, are examples of such techniques. DECIDING WHICH DUST SOURCE TO ADDRESS FIRST [If a longwall is out of compliance with dust standards, knowing where the extra dust is coming from helps to get back in compliance quickly.]

Jan 6, 2003