Search Documents

By T. E. Gray

This report describes the preparation characteristics of the most significant coal beds in Wise County, Va. It is one in a series of reports planned to determine coals suitable for the production of metallurgical coke, either as mined or after beneficiation. Wise County produced approximately 6,600,000 tons of coal in 1955, of which about 2,110,000 tons was cleaned mechanically. The Federal Geological Survey has estimated that 1,341 million tons of measured and indicated coal reserves remained in the county as of January 1, 1951.

Jan 1, 1958

By S. H. Katz

Artisans and laborers in mineral industries where the air is dusty with particles of reel: are subject to a peculiar pulmonary disease known as miners' phthisis or stone cutters' consumption. In granite cutters the disease is specifically designated as granite pneumoconiosis. Very fine particles of the harder rocks are especially injurious when inhaled into the lungs. It is estimated particles about one micron (1/23000 part of an inch in diameter) are most injurious, because larger particles are more readily removed by the cilia and,wet surfaces of the respiratory passages before reaching the lungs, while smaller particles either do not readily lodge or are more easily eliminated. Silica, of which quartz and flint are composed, and which forms a large part of granite, is one of the hardest of the common rock-forming materials. It is also very insoluble when silica lodges in the lungs elimination is difficult. Rock constituents of granite other than silica are probably injurious but in a lesser degree, and this is also probably true of limestone and the softer rocks. Ultimately a worker who daily inhales much granite dust has considerable deposited in his lungs. If he continues at his trade the lung tissue becomes harder and less elastic, he finds himself short winded, and in extreme cases death may come either directly or indirectly as a result of lung failure.

Feb 1, 1921

[Thin roport. C"WAW; I Ac rvq"I LN 01 a tvchniv&ll nnd oco I in j ;- I iv It i on c)l roncc p Ln,I I Lc!iin I OV Lhe undprnro"nd vNing, ruh h! i zn(kn, And 1" viiii rutoriin- of Opp &L :;halo drponi1q. Study L-I 10 1 1:; ..vi c I i rst d it cc tvd L ""Ards "vA I "it Wit "I the ippLWAhle q(t)¬logy, .in:;"(OLud ;hintvirak, r"ck muchnnics, ii; Olu rolturving, acum; mining, votitiInthn, iiiHtl I' it inn, vaFrry, :ind nn': iru"muniAl iNpiet InvI ors ConroptuAl mv:Lvmn wore nv"tWqjW rind Wen ovALUOILed agalnSt I lIt"n I it' 1 ttCS I runt ho I I I ;I I cc!ii i (.:I I A I I( I ocon "mi t?. vivwpn Lnt . Thu I CS" ICS 01 Lhunv vv&"Mions wpru thun ;lira ly-Ptl ind, KNqwd upon this analls is , hit foll"wkg two syntvmn writ' 5VIecLind lor furLhpu study in Phaso Ll: 4 -Ili I I : kcoiii nid Pi I lair -Art ica L DrL I I and Blasr SyKyw 1V: THOW Hori"g-Horiz"nuaL Ring Drill anti BI-ast Thiq rvpnrL is nahmillrd in fulAllarrit or We Phzni, J parLion ul (Arnt KICL Oinhou SON LO/ 1 by Nni x & Kc Won , I nc. Co thp D. nvor Rostnrch Cvntpr, Uni-LPd AL"tpn DWPAUxiont of the InLerilor, QUrCJlH of Mines. Ark wns tonpirrind as of March, 1979.]

Jan 1, 1975

By Charles H. Atkinson

The Rio Blanco massive hydraulic fracturing demonstration has been undertaken by the Bureau of Mines, Atomic Energy Commission, and a group of 15 industry participants. CER Geonuclear Corp. has been retained as program manager to evaluate the stimulation effects of very long fractures, suitably propped open in thick sections containing multiple intervals of low-permeability gas-bearing sands. The zone of interest for this demonstration includes Fort Union and Mesaverde sands from about 5,800 to 8,.200 feet deep in Rio Blanco County, Colo., about 1 mile from the site of the May 1973 triple nuclear detonation aimed at stimulating production from the same reservoirs. Drilling the test well and evaluating the reservoir prior to fracturing was funded by Government participants; fracturing and production testing will be funded by industry. The test well has row been completed at a total depth of 8,170 feet, and data obtained from logs, cores, production and drill-stem tests indicate reservoir conditions to be less favorable for gas production than anticipated. Structural position is lower than expected, resulting in higher water saturation than was determined for the same sands at the nuclear fracturing location. The lower sands of the Fort Union sequence appear to have higher shale content than has been encountered in other wells in the area. Despite the likelihood that gas productivity will be undesirably low following stimulation, the industry participants decided to proceed with the stimulation program with the thought that the resulting data would be useful. The success of the stimulation test probably will have to be judged by production increase rather than by production volume.

Jan 1, 1975

By O. C. Blade

This report on the properties of motor fuels sold through service stations in the United States was made in accordance with a cooperative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. This paper is a continuation of a series made in cooperation with the Coordinating Fuel Research (CPR) Committee of the Coordinating Research Council (CRC), Inc. The first of this series of reports presented data on motor gasolines sold during the winter of 1935-36, and succeeding reports described motor gasolines sold during the summers and winters to and including the summer of 1941. No reports were made on motor gasolines sold during the winter of 1941-42 and during the summer of 1942. However, starting with the winter of 1942-43, the semiannual reports were resumed.

Jan 1, 1949

By J. W. Thompson

ORE CONCENTRATION PROCESS-PATENT OIL FLOTATION PROCESS. The invention of the patent issued to Sullman, Picard & Ballot November 6, 1906 (United States Letters Patent No. 835120), is based upon the discovery of an wholly unexplained phenomenon arising from the agitation of ore pulp containing oil and air in certain proportions. This was a discovery in an art in which it was well known that the elements of oil, air, and agitation possessed certain characteristics and produced certain results. As early as 1860 a British patent first suggested the use of oil in water concentration of ores by pointing out the affinity which oils have for metallic sub- stances in preference to gangue. Subsequently many patentees employed the known affinity of oil for metal in ore concentration proc- esses by using oil in proportions varying from 2 per cent to 300 per cent of the ore and recovering the oil-coated metal particles by causing them to rise to the top or sink to the bottom of the pulp. In these processes the agitation was either gentle or thorough but never great, and though always employed to produce thorough oiling of the metal it was used in different degrees for the sole pur- pose of causing the metal particles to rise or sink. In the prior art the oil was used for its known selective affinity for metal, agitation was em- ployed to mix the oil with the metal, and air was introduced to supple- ment the buoyancy of oil in raising oil-coated metal particles to the surface. To this extent had the art of oil flotation advanced when the patentee entered it, having reached the commercial stage in only two processes, representing respectively metal-flotation and metal-sinking processes, and having reached the stage of success in none. In the line of experiments by the patentee when the proportion of oil to ore was reduced to 1.5 per cent a "float" appeared; at 1.04 per cent still more "float" appeared; at 0.32 per cent the "float" again vastly in- creased; at 0.1 per cent the "float" again vastly increased. It thus developed that in using oil at 0.1 per cent or even at 0.05 per cent of the ore and after violently agitating the pulp from 24 to 10 minutes, there arose to the surface when the pulp was brought to rest, a thick froth or foam of oil-coated air bubbles carrying oil-coated metal particles to the extent of about 90 per cent of the metal con- tent, the foam being sufficiently stable to permit removal and metal recoveries. This was a new result based upon phenomenon then unknown and still unexplained and constituted discovery and promised a change in the art of oil flotation from laboratory experi- ments and mill failures to commercial success. The patent referred to covering the points mentioned has been sustained by the District and the Circuit Courts of Appeals and by the Supreme Court. Miami Copper Co. v. Mineral Separation, 244 Federal, 752, pp. 754-757. ORE CONCENTRATION PROCESS-OIL FLOTATION-INFRINGEMENT. The Miami Copper Co. in its process of concentrating ores by the oil flotation process used three distinct processes that were either the processes included and covered by the Sullman, Picard & Ballot patent or their fair equivalent and which were clearly an infringe- ment of the patent, and the company can not escape liability for such infringement by taking an additional step, although such additional step if taken alone would not constitute an infringement of the Sullman, Picard & Ballot patent. Miami Copper Co. v. Mineral Separation, 244 Federal, 752, p. 768. ORE CONCENTRATION PROCESS-VALIDITY OF GREENWAY PATENT. The patent issued to H. Greenway, June 9, 1914 (Letters Patent No. 1999699), is valid. The process disclosed in this patent was a substantial departure from processes of the prior art. The heating of water is a matter of large moment and the use of acids is a matter of constant and considerable expense. By wholly dispensing with both by the use of a minute quantity of hydroxy compounds, the patentee has disclosed an original and novel plan which has broad- ened and made more simple the agitation process of air flotation. The novelty and inventive character of Greenway's discovery is patentable.

Jan 1, 1918

By Thomas C. Miller, Charles E. Mongan

"This publication is a progress report on Bureau of Mines studies in applying sonar techniques to roof-control problems in coal mines. Preliminary tests in the laboratory were made on layers of roof rock. To apply the experience thus obtained, a unit was designed and constructed and was used underground.The term ""sonar technique"" refers to the system of generating a beam of sound waves, shaping and directing the beam, introducing the beam into a medium to be studied, and examining any returning waves with a view of inferring the nature of the material traversed by the waves and the presence of interfaces or obstacles in the medium.The theory and actual underground experiments indicate that the sonic method is feasible. Information from physical tests made in the Bureau's Experimental mine confirmed the validity and potential usefulness of the sonar method. Lighter and more compact apparatus is desirable, and permissible equipment suitable for use in gassy or dusty mines must be developed. However, no particular difficulties are anticipated; consequently, this scientific approach to the exploration of roof strata shows definite promise. INTRODUCTIONThe problem of roof control in the coal-mining industry is of major importance. More than 50 percent of all coal-mine fatalities and 25 percent of all nonfatal serious injuries are caused by falls of roof, face, or ribs. The Bureau estimates that more than $128 million was spent by the coal-mining industry in 1958 for supporting roof."

Feb 1, 1960

By J. M. Stuve

Thermodynamic properties were determined by the Bureau of Mines for the intermetallic compound, TiA13. Heat capacities were obtained from 5 to 303 K by adiabatic calorimetry. The derived value of S2 1s is 22.08±0.07 cal/deg¬mole. Enthalpies relative to 298 K were obtained from 298 to 1,413 K by copper-block drop calorimetry. No anomalous thermal behavior was noted in the temperature ranges investigated. Low- and high-temperature data were combined with a known enthalpy of formation at 298 K to give values of enthalpy of formation and Gibbs energy formation, 0 to 1,400 K.

Jan 1, 1974

By C. W. Smith

The Bureau of Mines conducted laboratory-scale beneficiation tests on a sample of corundum gneiss from Montana to devise a method for beneficiating corundum for use as a substitute for refractory-grade bauxite. A flotation process utilizing petroleum sulfonate as the collector in an acid circuit was devised. Results showed that two flotation schemes each produced a concentrate exceeding the national stockpile specifications for calcined bauxite. From a feed containing 28 pct corundum concentrates containing up to 92.5 pct alumina (A1203) were produced with a corundum recovery of 78.5 pct.

Jan 1, 1987

By Lippe D. Sadwin

A high-speed streak camera method for making equation of state measurements (shock and particle velocities) on samples of rock under dynamic load conditions is described. Experimental data are given for tests on 12 samples representing 5 rock types. Analysis of these data shows that the method is practical and that good reproducibility of results can be obtained. The pressure range covered in the tests was from 1 to 50 kilobars.

Jan 1, 1966

By Clark F. Grain

These investigations were undertaken as part of the Bureau of Mines program for the development and evaluation of high temperature nonmetallic materials. This report consists of thermal expansion and phase inversion measurements by high-temperature X-ray diffractometry on the principal oxides of beryllium (BeO), calcium (CaO), titanium (TiO2 ), zirconium (ZrO2 ), hafnium (HfO2), and thorium (ThO2); all were high-purity commercially available oxides. Thermal expansion values were calculated from unit cell dimensions measured at selected temperatures. Expansion was determined parallel to each major crystallographic axis for the anisotropic oxides: BeO, TOi2, ZrC2, and HfO2. Combined random and systematic errors in the thermal expansion values are considered to be less than 3 percent of the total expansion at 500° C. and approximately 2 percent at 1,000° C. No hysteresis in the expansion curves was noted between heating and cooling cycles. The Bureau's values were compared with published expansion measurements obtained by X-ray diffraction, dilatometric, interferometric, and telemicroscopic techniques. For anisotropic oxides, average linear expansion values were calculated from the volume expansion.

Jan 1, 1962

By E. C. Lane

The motor gasoline that is being marketed in the United States this winter is in general, more volatile than that sold a year ago. This increase in volatility is shown by a lowering of the distillation temperatures, ranging from 2°F. at the average initial boiling point to 5°F. at the average end point. During the past eight and. one half years the Bureau of Mines has made semi-annual surveys of the gasoline marketed in the United States, the survey Just completed being the seventeenth in the series. The cities in which samples have been collected, have been chosen as representative of the more important marketing territories, as it is obviously impracticable to obtain a sample of every gasoline sold in the entire country. Samples were collected in Boston for the first time since 1919. It was believed advisable to include samples from that district in order to give a better balance to the survey for the country as a whole.

Jan 1, 1928

By Loren R. Anderson

This Volume documents the use of the Cone Penetrometer data analysis computer programs VERT and HORZ. The programs are interactive in that they prompt the user for input data and allow correction and modification to be made. The programs read data from the results of cone penetrometer soundings and convert the data to values of tan ø. Mean, standard deviation, skew, kurtosis, linear trends and autocorralation are computed by the programs.

Jan 1, 1982

By Natesa I. Jayaraman

This report describes recent improvements the Bureau of Mines made in the design of its shearer-clearer water-spray system for dust control on lonwgall shearer faces. The improvements were based on findings from a field survey of six mines and laboratory test results. The report in-cludes information on installation and use of the improved shearer-clearer system and describes a field installation and 3-week underground test of the system. The improved shearer clearer, like its predecessor, reduces dust concentrations in the shearer operator's walkway by splitting the airflow on the upwind side of the shearer and confining the dust cloud to the face side of the shearer. The improved shearer-clearer system utilizes more practical-mounting locations for the water sprays and requires less water consumption. In the underground test, the improved system maintained the clean-air split in the walkway up to 40 ft downstream from the shearer. To further improve dust suppression, cooling-water manifolds were relocated into the loading zone. The laboratory and underground tests showed that the improved shearer-clearer system and the techniques described can significantly reduce the respirable dust exposure of shearer operators from shearer-generated dust.

Jan 1, 1985

By Carlton E. Brown

Broom and Yant6/ recently described a. microprojection method for determining the particle-size distribution and number concentration of samples of dust collected from the air by such samplers as the Owens jet dust counter) and the thermal precipitator8/ . This method was developed to obviate or reduce the eyestrain consequent to the regular filar-micrometer method9/ and to save time and work. The article stated that work was in progress on a micrcprojection method for counting impinger dust samples; this article describes the method developed. ACKNOWLEDGMENTS The assistance of the personnel of the ventilation Department of the Anaconda Copper Miring Co., Butte, Mont., in developing this method and particularly in suggesting a suitable material to use for the microprojector screen is sincerely appreciated. Much of the work was done in the laboratory of the Anaconda Copper Mining Co. on samples collected in Butte mines during a cooperative study with this Bureau.

Jan 1, 1938

By Carlton E. Brown

Brown and Yant6/ recently described a microprojection method for determining the particle-size distribution and number concentration of samples of dust collected from the air by such samplers as the Owens jet dust counter7/ and the thermal precipitator8/. This method was developed to obviate or reduce the eyestrain consequent to the regular filar-micrometer method9/ and to save time and work. The article stated that work was in progress on a microprojection method for courting impinger dust samples; this article describes the method developed. ACKNOWLEDGMENTS The assistance of the personnel of the Ventilation Department of the Anaconda Copper Mining Co., Butte, Mont., in developing this method and particularly in suggesting a suitable material to use for the microprojector screen is sincerely appreciated. Much of the work was done in the laboratory of the Anaconda Copper Mining Co. on samples collected in Butte mines during a cooperative study with this Bureau.

Jan 1, 1938

By Robert K. Koch

The reactions of alumina and alumina monohydrate with wet hydrogen fluoride gas were studied by the Federal Bureau of Mines to determine the feasibility of producing commercial-grade aluminum fluoride from offgases generated by pyrohydrolysis of siliceous fluorspars. The test results showed than an aluminum fluoride reactor operating at maximum efficiency could retain 96 percent of the fluorine contained in off-gases generated by pyrohydrolysis of siliceous fluorspar. The requirements are a reactor temperature of 200° C. and a reactor entrance gas containing 5 mole-percent hydrogen fluoride. Partial pressure equilibrium constants were determined for the reaction of alumina monohydrate and wet hydrogen fluoride gas from 200° to 350° C. and for the reaction of alumina and wet hydrogen fluoride gas from 350° to 700° C. Both reactions are reversible, and they proceed in directions that are dependent upon the temperature and the relative HF:H2O concentration. Logarithms of the equilibrium constants were used to plot the reaction isobars; these can be used to calculate the theoretical maximum efficiency of a reactor processing wet hydrogen fluoride gas between 200° and 700° C. The theoretical maximum efficiency decreases with increasing temperature.

Jan 1, 1961

By E. G. Davis

As a result of interest by the U.S. Department of Energy, the Bureau of Mines conducted studies on comminution of bituminous coal to the 2-um particle size range using the Bureau-developed turbomill. Both "plant grind" size (80 pct minus 75 um) and microsize (minus 10 um) coal can be produced in a single step with the Bureau's turbomill. In 15 min, minus 2.4-mm coal milled in water with steel shot was reduced tc 65 pct minus 75 m and 26 pct minus 2 m, with an energy requirement of 139 kW^h/mt coal. Plant-grind size coal milled in water, with Ottawa sand as the milling medium, was reduced to more than 45 pct minus 2 m in 15 min, at 175 kW?h/mt. Plant-grind coal milled with steel shot was reduced to 57 pct minus 2 um in 15 min, at 138 kW?h/mt. When diesel fuel was substituted for water, the milling of the coal was less effective and less energy efficient. Keeping the pulp dispersed was critical. Without an effective dispersant, the slurry became very viscous with increased milling time, resulting in higher energy requirements, low heat dissipation, and poor grinding efficiency.

Jan 1, 1987

By F. W. Brown

In 1942 the Explosives Division investigated electrostatic hazards associated with the manufacture, storage, and use of explosives. A report was issued in 19454/ presenting the data on the spark sensitivities of explosives. In 1948, the apparatus was redesigned and rebuilt to make the routine testing of explosives safer and more convenient. The rebuilt apparatus is described in this re-issue of the former report. Included are details of construction and a list of parts. PRINCIPLES OF METHOD In normal procedures without special precautions, it is possible for static charges to be accumulated on individuals or on ungrounded equipment or structures.5/ Static charges may be produced in many ways, but they are most commonly produced by rubbing or successive contact and separation of unlike surfaces, at least one of which is usually an insulator.

Jan 1, 1953

By H. A. Tucker

This Bureau of Mines investigation was conducted to determine the appropriate quantities of rare-earth methals (REM) in the form of silicides to add to an alloy steel for the purpose of increasing toughness and ductility. The work was conducted in a vacuum induction furnace with the rare-earth additions required to deoxidize and desulfurize a simulated basic oxygen furnace (BOF) vacuum-degassed steel initially containing 0.013 to 0.016 percent sulfur. The product proved to be as good or better than the best basic electric furnace steel of the same composition made by the steel industry. Twenty-three experimental heats of 5 Ni-Cr-Mo-V steel were made, cast into 50-1b ingots, and hot-worked in a press and a rolling mill to ½ inch plates which were then heat-treated to 130/150 ksi4 yield strength. Impact and tension tests showed that the addition of 0.025 to 0.100 percent, or ½ to 2 lb per ton, respectively, of rare-earth metals when compounded with silicon were appropriate for increasing toughness and ductility. These quantities resulted in retained cerium contents between 0.014 to 0.025 percent, and increased the Charpy V-notch energy absorption and the percent reduction of area significantly as compared with base heats at the same sulfur content levels. All the test heats, including those with additions of REH of as much as 4 lb/ton, had greater Charpy V-notch energy absorption values than the base composition could have developed at the starting sulfur range of 0.013-0.016 wt pct.

Jan 1, 1968