Search Documents

By R. Barany

The heats of formation of gehlenite and talc were determined by hydro-fluoric acid solution calorimetry. The results are reported in terms of the constituent oxides (?H298.15 = -31.1 ± 0.5 kcal/mole for gehlenite and ?H298.15 = -44.9 ± 0.3 kcal/mole for talc) and in terms of the constituent elements (?H298.15 = -952.8 ± 0.7 kcal/mole for gehlenite and ?H298.15 -1,415.5 ± 1.4 kcal/mole for talc).

Jan 1, 1963

By F. Sillers, R. T. C. Rasmussen

"INTRODUCTION This is the fourth report of investigations dealing with the cooperative tests between the Bureau of Mines and industry on the use of electrolytic manganese in steelmaking. The first report dealt with the use of electrolytic manganese in the manufacture of stainless steel 3/ the second with its use in acid electric steel practice, 4/ and the third with its use in low-carbon basic open-hearth steelmaking. 2/ A résumé of those investigations E7 appeared in the magazine STEEL. 5/ The present report deals with the use of electrolytic manganese in the manufacture of four types of stainless steel and the new Timken 16-25-6 alloy. The Bureau of Mines supplied The Timken Roller Bearing Co. with 62,000 pounds of electrolytic manganese for use in the tests.The electrolytic manganese was produced at the Bureau of Mines pilot plant, Boulder City, Nev., by the process developed by the Bureau and described in Bulletin 463, Operation of Electrolytic Manganese Pilot Plant, Boulder City, Nev., by J. H. Jacobs. J. W. Hunter, W. H. Yarroll, P. E. Churchward, R. G. Knickerbocker, R. W. Lewis, H.A. Heller, and J. H. Linck. The workcarried out under the direction of R. S. Dean, formerly assistant director, Bureau of Mines, and R. G. Knickerbocker, formerly chief, metallurgical branch, as part of a long-range program involving the development, manufacture, and use of manganese from domestic ores. Preliminary arrangements for the plant tests were made by the late A. A. Dow. 7/"

Jun 1, 1947

By Robert F. Randolph, Dana C. Reinke, Richard L. Unger

Purpose The NIOSH Hearing Loss Simulator is a software training and communication tool for promoting hearing loss prevention. It allows a user or trainer to demonstrate the effects of noise exposure on hearing without experiencing an actual noise-induced hearing loss. Estimates of the effects of different levels of noise exposure are based on the American National Standard Determination of Occupational Noise Exposure and Estimation of Noise-Induced Hearing Impairment, otherwise known as ANSI S3.44. This standard specifies the predicted hearing loss for noise-exposed populations of individuals based on risk factors that include gender, age, sound levels (in A-weighted decibels or dBA), and years of exposure. Algorithms specified in the standard were derived from empirical studies of populations that had no exposure to loud noise and other populations that had experienced various levels and durations of noise exposure. This manual explains the major objectives that can be addressed with the simulator and training scenarios that can be applied to real-life, real-worker scenarios. The majority of this guide explains the simulator's functions in detail. Simulator users are encouraged to read this manual while learning how to run the software. [ ] Training Objectives The main objective of the Hearing Loss Simulator is to increase motivation for taking effective hearing prevention action by demonstrating simulated noise-induced hearing losses. [The Simulator can also help teach the following facts about hearing loss. Hearing loss is affected by noise levels. Hearing loss worsens as the noise exposure duration increases. Hearing loss can become permanent. Hearing loss makes it harder to hear what others say. Most hearing loss is not caused by age. Speech is made up of both low and high pitch sounds. Hearing loss due to noise makes it harder to hear high pitch sounds. Hearing loss due to noise has less of an effect on hearing low pitch sounds.]

Jan 3, 2008

By Brian P. Stapleton, Bill M. Stewart, Joel R. Warneke, Curtis C. Clark

Of the 28 accident/injury classifications listed by the Mine Safety and Health Administration, handling materials is second only to roof falls in terms of generating the highest number of reportable accidents in active underground coal mines. Two materials-handling activities that cause numerous injuries each year are the categories of “handling supplies or material, load and unload” and “moving power cables.” Mechanization and mine worker activity training are two methods that can aid in preventing these injuries. This paper describes three mechanical methods—the mobile manipulator, the in-mine hoist, and a cable-handling system—being developed and tested at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health. Two of the devices are specifically designed for loading, unloading, and moving supplies and materials, and the third device is for handling trailing cables in the confined spaces of coal mines. Also described are safety solutions developed for underground coal mines geared to showing miners safe and unsafe ways of performing various materials-handling tasks.

By D. V. Keller

Black lung disease, or paeumocomosis, is a serious health hazard for workers working in a coal mine. Though the exact cause of black lung disease is not known, it is certain that prolonged inhalation of fine coal particles, ever present in the mines, does give rise to black lung disease. For a long time, it also has been known that limestone applied to coal dust mine surfaces tends to hold down coal dust thus preventing it from refloating in the air of the coal mines. Since the humidity in the mines may be generally high, this also might be an important factor in the particular substrate system behavior. Fine solid particles stick to other particles and surfaces very indiscriminately. The term adhesion is used for the phenomenon of attachment of particles to surfaces whereas cohesion is used for the phenomenon of attachment of particles to each other. The measurement of the force of adhesion of coal particles to coal substrates presents a great problem, especially in the case of particles in the size range of a few microns. These micron sized particles are at the limit of the resolution of the optical microscope and therefore an electron microscope has to be used for this purpose. The forces of adhesion between these particles and substrate may be very strong and can exceed the weight of the particle by four to five orders of magnitude.

Jan 1, 1973

By D. O. Kennedy

THIS CHAPTER on minor nonmetals covers greensand, meerschaum, mineral wool, and wollastonite. Mineral wool was by far the most valuable material among these minor nonmetals reported in the United States in 1956. GREENSAND Output of greensand (glauconite) declined in 1956. The Kaylorite Corp., Dunkirk, Md., and the Inversand Co., Sewell, N. J., were the only firms that reported production of this commodity. Output came from open pits in Calvert County, Md., and Gloucester County, N.J.

Jan 1, 1958

By D. E. Pollock, J. A. Organiscak

Water sprays and water powered scrubbers have both been utilized in the mining and milling industry to suppress airborne dust. Unconfined water sprays operated at lower water pressures of ?689 kPa (?100 psig) can be very effective at wetting the mine product at the dust source and significantly reducing the amount of respirable dust that becomes airborne. However, unconfined waters sprays can be somewhat ineffective in actually removing airborne dust from the air. On the other hand, water powered scrubbers operating at higher water pressures of ?1,724 kPa (?250 psig) in physical enclosures or ducts have previously been demonstrated to be very effective in removing airborne dust from the air. These higher operating water pressures are uncommon in many mines and mills, so their use is limited. The National Institute for Occupational Safety and Health (NIOSH) recently investigated the performance of a lower-pressure, water powered inline series spray scrubber for removing localized airborne dust emitted at the source. Results showed noticeable improvements in airborne dust capture efficiency through the operation o f multiple inline series hollow cone spray nozzles within a round duct or pipe at the same water pressure as a single spray. Operating hollow cone spray(s) at higher water pressures noticeably improved airflow through the scrubber and yielded some additional scrubber efficiency improvements. Thus, in-line spray scrubber efficiency trade-offs were observed to be made by altering spray power components of water pressure and/or quantity (number of sprays). Results show that, on average, up to 0.23 and 0.32 m3/s (484 and 679 cu ft per min) of airflow at 0.81 and 0.69 dust capture efficiencies can be achieved with three 81° and 33°hollow cone inline series sprays, respectively, operating at 1,655 kPa (240 psig).

By Steven W. Schmauch

The Ruby Mountains study area encompasses 75,615 acres managed by the U.S. Bureau of Land Management in Madison County, MT. A mineral survey was conducted by the U.S. Bureau of Mines and U.S. Geological Survey in 1984. Bureau of Mines personnel reviewed literature and county mining records, and examined prospects or mineralized areas to determine mineral resources. Geological Survey personnel evaluated the area by geochemical sampling and geophysical surveys. There are no organized mining districts and no current claims in the study area. Significantly mineralized quartz veins, shear zones, or talc bodies apparently do not exist within the study area. A small part of the Kelly Iron Deposit is inside, but dips away from the study area; the main occurrence is estimated to have 32 million tons of subeconomic resources that average 21 percent iron.

Jan 1, 1985

By A. B. Campbell

The Bureau of Mines is developing alloys using ion implantation as an alternative to bulk alloys that consume large quantities of strategic materials such as chromium and nickel. These alloys are formed at the outer layer of relatively common materials. To more fully understand the corrosion characteristics and physical properties of this outer layer, it was necessary to deter-mine the alloy concentration as a function of depth into the substrate material. Also, since many of the ion-implanted alloys would be utilized at elevated temperatures, it was necessary to determine the diffusion behavior of the implanted element. Proton-induced X-ray emission and inert gas ion sputtering have been utilized to generate composition depth profiles for Fe-Cr, Fe-Ni, and Fe-AI ion implanted alloys fabricated by implanting 25-kev Cr+, Ni+, or AI+ into iron substrates. The data were fitted (utilizing a computer program) with symmetrical Gaussian profiles yielding values for the range and range straggle of the ions. These parameters were then compared with those calculated from theory. Changes in the profiles due to annealing were investigated and values for the diffusion coefficient were obtained assuming diffusion according to Fick's Law. For the Cr+ and Ni+ implantation, the profiles as-implanted agree reason-ably well with theory and exhibit ?norrmal" diffusion characteristics at 500° C. For the Al+ implantation, the profile as-implanted is much broader than predicted and exhibits substantial enhanced diffusion at temperatures up to 500° C.

Jan 1, 1979

By James R. McVey

A new method for measuring deformations of rock surfaces in underground excavations has been suggested by Dr. James Powell of Brookhaven National Laboratories (BNL) and subsequently developed and successfully demonstrated in a mining environment by the Federal Bureau of Mines, Spokane Mining Research Center (SMRC) and Brookhaven National Laboratories. The system uses 35-mm photography of targets strategically located on surfaces of interest, such as across the roof and on the sides of a mine drift or tunnel. The optimum tar-get, as determined in this investigation, consists of a white ?X? made with 1/8-inch-wide reflective tape on a black 6-inch square. Photographs, taken in pairs from two separated camera positions and at regular time intervals, were analyzed at the Bureau by hand and at Brookhaven National Laboratories using techniques and equipment similar to those used in cloud chamber film analysis. Test results show that deformation-measurement accuracies of better than ±0.020 inch in a drift that is 20 feet wide can be expected. This degree of accuracy, plus providing displacement data in the X, Y, and Z directions (rather than the one direction formerly possible), makes this a noteworthy and useful tool for industry as well as for mining research.

Jan 1, 1974

By E. R. Spencer, E. R. Bauer

Previous studies and research efforts have shown that noise-induced hearing loss (NIHL) is a problem in the U.S. mining industry. In response, researchers at the National Institute for Occupational Safety and Health (NIOSH) have been conducting a cross-sectional survey of equip­ment noise and worker noise exposures in the mining industry to estimate the potential for NIHL within the mining community. One commodity recently surveyed was the extraction of sand and gravel from surface pits and by dredging. To address the potential for NIHL in the sand and gravel industry, sound levels on and around the dredges and processing equipment were recorded to iden­tify areas of high noise levels. Full-shift worker dosimetry, in conjunction with task observations, was documented to determine the relationship between exposure and source. This paper presents research examining noise on dredges used in several surface mine sand and gravel operations and in the processing facilities. Results indicate that there are areas on the dredges (crane, suction pumps and diesel engines) where sound levels greater than 90 dB(A) are pres­ent. In addition, crushers and screens used in the processing of the sand and gravel also generate sound levels greater than 90 dB(A). Although no surveyed worker exceeded the Mine Safety and Health Administration’s (MSHA’s) permissible exposure level (PEL) of 90 dB(A) eight-hour time-weighted average (TWA8), laborers, mechanics, oilers, helpers, pickers and greasers are the workers most likely to be exposed to hazardous sound levels and to thus develop NIHL over time

By J. C. Johnson, W. G. Pariseau, D. F. Scott, F. M. Jenkins

In situ stresses are important input data for the design of safe, stable stope layouts and extraction sequences. However, it is commonly assumed that normal and shear stress gradients in a stress field are negligible and, consequently, that stresses are uniform throughout the region of analysis. To evaluate these assumptions and to provide input data for an analysis of a shaft pillar mining plan, in situ stresses were measured at the Homestake Mine, Lead, SD, using overcoring on hollow inclusion cells and borehole deformation gauges. These measurements were used with conventional least squares, best fit data reduction schemes. The results showed that normal stresses within the shaft pillar were less than, but comparable to, those estimated from finite-element modeling. Shear stresses were an order of magnitude less than normal stresses and varied considerably from site to site. Possible causes of this variability include effects of scale, elastic moduli, anisotropy, and axial strain. Because of the variability, it is not possible to determine the magnitude of horizontal stress gradients.

Jan 1, 1993

By Sidney Katell

The reaction of coal, oil, or natural gas with air and oxygen and/or steam yields a gas containing varying amounts of impurities. Depending on the raw material and the end use of the product, these impurities include solids, such as dust or slag, and gases, such as hydrogen sulfide, carbon dioxide, and nitrogen. Considerable effort has been expended in developing and operating purification systems, and the literature is replete with equipment data and operating results. The research problems, the design, and the operation of the various systems have been the subjects of patent applications, journal articles, and textbooks.

Jan 1, 1959

By K. K. Kelley, W. W. Weller

Heat capacity measurements of lead molybdate and lead tungstate were conducted over the temperature range from 51 ° to 298 ° K. The entropies were found to be S298.15 = 39.7 ± 0.5 cal / deg mole for lead molybdate and S298.15 = 40.2 ± 0.5 cal / deg mole for lead tungstate . The entropy values were combined with other pertinent data to obtain the entropies of formation of the two compounds from their constituent elements and oxides .

Jan 1, 1964

By R. A. Meyer

A table that greatly simplifies determination of metastable transitions in mass spectra has been prepared. All the mathematically possible metastable transitions of any compound whose molecular weight lies between 26 and 150 can be determined from the table without calculation. The method of utilizing the table is described, using selected peaks from the spectrum of normal butane for illustration. In the mass spectrometer, ions are formed in the isatron and accelerated through a series of slits. Most of these ions reach the collector without further change, but a few dissociate in transit to form new ions. These ions appear in the mass spectrum at neither the mass--to-charge ratio (m/e) of the original ion nor that of the new ion. A formula that relates the appearance of these new ions to the ion from which they were formed is: [ ]

Jan 1, 1957

By Peter H. Toepfer

This report presents the factual data obtained by the Bureau of Mines during diamond-drilling investigation of the Sunset copper deposit in the Index mining district, Snohomish County, Wash. The Sunset mine, first produced copper ore in 1902, but its main period of activity was from 1923 through 1930, The mine has produced 263,500 tons of ore, from which 1,500 ounces of gold, 156,000 ounces of silver, and 12,912,000 bounds of copper-were recovered. The mine has, been idle since 1946

Jan 1, 1953

By Paul T. Allsman

Iron-ore deposits in southwestern Utah, as the major source of iron ore for western steel plants, were investigated by the Bureau of Mines in 1942-45 in cooperation with property owners and operators and with the assistance of the United States Geological Survey with a view to determining and extending the known reserves. The factual data resulting from that project were presented in a previous report and in a report on the geophysical surveys now in course of publication. The present report has been prepared in response to expressed public interest in the ore reserves of Iron County. Mining began in the district in 1871} but. did not become important until 41 1923. From 1923 to 1946, inclusive) production totaled 10,139,500 long tons. In 1945 the district yielded 1,931,749 long tons containing 52.84 percent iron; in 1946 the corresponding figures were 1,317,671 and 53.75. The deposits lie .in a narrow, 23-mile long belt extending northeasterly from Washington 'County into Iron County along a line of mountains, chief of which are Iron Mountain, Granite Mountain, 'and Three Peaks in Iron. County. The deposits are hematite-magnetite bodies, chiefly in limestone near its contact with the monzonite of the mountain masses, but with a few important veinlike bodies in the monzonite or at the contact. They range in size from small pods to several millions of tons, and in depth from surface or near-surface to a known maximum of 1,300 feet:

Jan 1, 1948

By Jack D. Ramsdell

The objective of this investigation was to make a preliminary evaluation of titanium-vanadium-zirconium, alloys using room-temperature tensile properties as criteria for selecting promising alloys for future critical studies. Arc-melted titanium-vanadium-zirconium alloys ranging in composition from 5 to 20 a/o (atomic-percent) vanadium and 5 to 30 a/o zirconium, were investigated to evaluate hardness, hot workability, and room-temperature tensile properties. Metallographic examination coupled with hardness measurements were used to follow structural changes and aging response. Room-temperature tensile properties were criteria for evaluating mechanical and engineering properties of the alloys.

Jan 1, 1960

By Terry J. Close

In 1992, as part of the U.S. Bureau of Mines Idaho Land Assessment Program, the Western Field Operations Center investigated the mineral resources of the 30,300-hectare Elk Summit study area. The area is in the Clearwater National Forest, adjoining the Selway-Bitterroot Wilderness in Idaho County. Idaho. The study area is underlain by granitic and metasedimentary rocks. Associated with these rocks are road metal (stone) resources, black sand mineral placer resources, and thermal water resources. Also present are abundant sand and gravel. Two of the five sites examined during the Bureau study have road metal (stone) resources, one has black sand mineral resources, one has thermal water resources. The fifth site is a black sand mineral placer occurrence. There is no evidence of petroleum or coal resources. Idaho County records indicate that 38 mining claims, mostly black-sand placer, have been located in the study area, Twenty-three of the claims are current. Workings consist of a few pits and trenches at the placer, and two borrow pits. The only mineral commodity produced from the area was about 1,500 tonnes of stone excavated from the Savage Pass and Swamp Creek borrow pits along the Elk Summit road, north of Hoodoo Lake. The stone was used to surface the road; these stone resources will continue to be used as needed.

Jan 1, 1993

By A. B. Clayton

The Bumpus Cove area is in Unicoi County, Tenn., about 9 miles south of Jonesboro and 5 miles northwest of Erwin. Iron and lead ores were mined in the Bumpus Cove area before the American Revolution. The production of those metals continued intermittently until 1916. In 1850 this area was the most important producer of iron in the South. In 1911 several carloads of zinc ore was recovered from old dumps and shipped to Missouri smelters. In 1913 systematic mining of zinc ores was begun and continued until 1916. After that year, mining again became sporadic and continued so until discontinued in 1943.

Jan 1, 1949