Search Documents

By J. P. May

This U.S. Bureau of Mines report identifies and evaluates factors responsible for dump-point accidents involving mobile mining equipment. Information regarding the occurrence and severity of the accidents, the industries affected, the types of equipment involved, the primary and contributing causes, and pertinent Federal regulations is included. The aim of this report is to provide information that will aid mine operators in the recognition of hazards associated with mobile equipment operation near the dump points of stockpiles and waste dumps.

Jan 1, 1990

By R. R. Wells

For several years the Klukwan deposit near Haines, Alaska, has attracted interest as a potential source of iron. Limited field and laboratory investigation has indicated that the deposit contains a large amount of Iron that is recoverable as high-grade concentrate. This report summarizes the results of laboratory beneficiation testing of the Klukwan ore, as represented by six samples submitted to the Alaska Experiment Station of the Bureau of Mines, Juneau, Alaska, Iron is present in the ore as a fine-grained magnetite associated with a pyroxenite type basic rock.. Satisfactory magnetic-separation procedures were developed for the production of concentrates assaying more than 60 percent Fe and 2 to 4 percent Ti02. During the investigation many data were obtained and compiled, but for convenience and clarity data of secondary importance have been omitted or condensed; only the more pertinent test results are discussed in detail.

Jan 1, 1953

By David R. Peterson

This user's manual covers a set of 5 computer codes which were generated during development of a simulation of deep ocean mining operational economics. Table 1.1 provides a summary of these codes, and a more thorough description of each follows, In addition to the descriptions in this user's manual, internal documentation is provided throughout each code, except for the very simple ones, for ease of understanding or possible modification. The two major codes are MINER, which performs the deep ocean mining system operational simulation, and MSWEEP, which calculates the sweep and feed efficiencies for a set of collector paths generated by MINER. The standard operating procedure is to input the system and operating parameters to MINER, which computes a set of collector paths automatically and stores the information in the fife PATH.DAT. MSWEEP subsequently retrieves the collector path data in PATH.DAT, and uses it to calculate sweep and feed efficiency. Separating MINER and MSWEEP allows parmetric execution of MSWEEP without recomputing the collector paths with MINER. PIPEST, RESP, and OBSTCL are special-purpose codes described in more detail in the following documentation.

Jan 1, 1979

By W. P. Yant

A previous report of the Bureau of Mines dealt with the toxicity of dichlorodifluoromethane, a new refrigerant that has a remarkably low toxicity. Continued research by the Frigidaire Corporation and toxicological experiments performed in the Laboratory of Applied Physiology of the University of Cincinnati revealed another organic fluoride, dichlorotetrafluoroethane, whose toxicity also appeared to be of a very low order and whose physical and chemical properties make it suitable for refrigeration purposes. In addition to low toxicity, safety in its use is further enhanced by its physical properties, which permit the design of equipment that operates at comparatively low pressures and hence mitigates the dangers and problems of leakage. The investigation described in this report was performed by the Bureau of Mines at the request and with the cooperation of the Frigidaire Corporation.

Jan 1, 1932

By Joseph A. DeCarlo

This publication presents a tabulation of oven-and beehive-coke plants in the United States as well as pertinent statistical data on the number, capacity, kind, and condition of the ovens. Coke is an essential raw material in pig-iron production and the coal-chemical materials produced during the coking process are used to manufacture fertilizers, paints, plastics, synthetic rubber, explosives, detergents, nylon, pharmaceuticals; dyes, and many other products necessary to the high standard of living in this country. In table 1 the oven-coke plants in the United States on December 31, 1959, are listed. This shows the name and address of the company, location of the plant, classification or type of ownership, number and type of ovens, annual coke capacity, and the coal-chemical materials produced. The "furnace" plants I are those owned by iron and steel companies and most of them are integrated with blast furnaces to facilitate transportation of raw materials for steel making. Furnace plants represented 87 percent of the total coking capacity and their average annual capacity was 1. 3 million tons. The "merchant" plants are those associated with chemical companies, gas utilities, as well as those that produce metallurgical, industrial, and residential-heating grades of coke and coal-chemical materials for sale on the open market. These coke plants are smaller than furnace plants and in 1959 their average coke capacity was only 520 thousand tons annually. On December 3l, 1959, there were 54 furnace and 20 merchant oven-coke plants in existence in the United States.

Jan 1, 1960

By Nicholas Kyriazi, John P. Shubilla

The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory, has undertaken a study to determine how well self-contained self-rescuers (SCSRs), deployed in accordance with Federal regulations (30 CFR 75.1714), hold up in the underground environment with regard to both physical damage and aging. This report presents findings regarding laboratory-tested SCSRs in the sixth phase of testing from mid-1996 to early 1998. The SCSRs were tested on human subjects and on a breathing and metabolic simulator. These results indicate that most of the apparatus, if they pass their inspection criteria, perform satisfactorily. However, the deployed CSE SR-100s exhibited significantly higher inhaled CO2 levels than new units, as in the previous phase. This will cause higher ventilation rates in most users, which will, in turn, result in higher breathing pressures, possibly causing users to prematurely remove the apparatus. CSE Corp. has developed a noise test that can identify apparatus suffering from chemical-bed degradation causing the early CO2 breakthrough. This test was added to the inspection criteria for the SR-100. In addition, several of the MSA Portal-Packs that passed their inspection criteria were found to have KO2 dust in their mouthpieces. Further investigations by NIOSH and the Mine Safety and Health Administration confirmed these findings, which resulted in the decertification of the apparatus and their removal from service.

Jan 1, 2000

By S. J. Pearce

The Bureau of Mines has prepared, as circumstances have dictated, a series of Schedules setting forth the minimum requirements that various types of equipment should meet to be considered safe and satisfactory for use in certain hazardous or unhealthful conditions. These Schedules cover a wide variety of devices ranging from explosives to electrically operated mine locomotives. This paper deals with those Bureau of Mines Schedules under which respiratory protective devices are tested and approved, and its purpose is to explain the function and operation of these Schedules. Provisions have been made for testing and approval of the following types of respiratory protective devices: Self-contained breathing apparatus,2/ supplied-air respirators,3/ gas masks,4/ dispersoid respirators,5/ and chemical cartridge respirators.6 These devices are tested at the Central Experiment Station of the Bureau of Mines in Pittsburgh, Pa. Self-contained breathing apparatus is tested by the Safety Branch, and the other types of respirators are tested by the Health Branch.

Jan 1, 1951

By Raymond B. Ladoo

Toward the end of 1920 , the average grades of ground feldspar offered to the pottery industry were so poor and so generally unsatisfactory that many of the largest consumers decided to take active steps for their own protection . A few of the potters made arrangements to grind their own feldspar , while others asked the Bureau of Mines to make a detailed study of the problem and to suggest methods of improvement . Accordingly such a study was undertaken, the partial results of which are outlined in this preliminary report . The outstanding features of the present feldspar industry which are of interest in this connection are stated below. (1 ) Many grinding companies do not own or control all or even a major part of their sources of crude material , but buy in job lots from many sources . (2 ) There is great need of more adequate engineering and chemical control over mines and mills . ( 3) ~ Out of date , inefficient methods and equipment for mining and grinding are in common use . (4) Little or no cooperation exists between feldspar producers , but on the contrary many feldspar companies are exceedingly secretive . This tends towards (a) preservation of obsolete methods ; ( b ) want of knowledge of the essential features of production , market requirements , and the relation between total milling and consuming capacities of the country; ( c ) inefficient and often mistaken trade practices ; ( d) unprofitable and even ruinous competition in dull periods . (5) The small size of many feldspar deposits precludes maintenance of an efficient organization at each individual mine . ( 6 ) Many of the best deposits of feldspar situated close to railroads are becoming depleted , which results in gradual lowering of grades , and increase in cost for better grades . (7) There is a lack of exact mowledge of the ceramic properties and behaviour of feldspar by some consumers , which results in ( a) purchase of feldspar on the basis of price alone , thus encouraging low production costs at the expense of quality , and ( b) inefficient and expensive cross- hauling of both crude and ground feldspar .

Jan 1, 1922

By John L. Miller

The synthetic fluormicas may be divided on the basis of silicon content into tetrasilicic, trisilicic, and disilicic. Properties of lead and barium disilicic fluormicas were determined to characterize these two representative members of the disilicic group. Properties described include unit-cell parameters from X-ray diffraction, optical data, chemical composition, density, melting point, and mechanical and dielectric properties. Both the lead and the barium micas were typically monoclinic; neither was sufficiently cleavable to yield usable mica splittings. Both yielded polycrystalline, machinable ceramics with excellent mechanical and dielectric properties.

Jan 1, 1963

By T. J. Batchler, T. M. Barczak

The Code of Federal Regulations (CFR) requires that the transverse load capacity of stoppings be equal to or greater than traditionally accepted in mine controls, which for block stoppings is generally accepted as 39 psf as referenced in the preamble to the CFR standard. This measure is based on physical testing of a freestanding wall in accordance with ASTM E 72 specifications, where our past research has shown that the dominant parameter is the tensile strength of the sealant. A new protocol based on rigid arch loading of the structure is proposed to determine the true transverse load capacity of block stoppings. Arching is achieved by the restraint of the stopping against the mine roof and floor, whereby compressive forces are developed within the wall. A laboratory procedure using the NIOSH Mine Roof Simulator (MRS) to simulate rigid arching of block stoppings was developed and results verified through full-scale in-mine tests. The rigid arch tests have demonstrated transverse load capacities more than an order of magnitude higher than the ASTM E 72 evaluation method from which the 39-psf requirement is derived. More importantly, the rigid arch tests have shown that the load capability is dependent on the physical properties of the block and geometric properties of the wall and not the sealant.

By F. E. Brantley

Research was undertaken by the Bureau of Mines to assess the technical feasibility of smelting cement-copper precipitate in an electric furnace to produce commercial-grade copper. The blister-grade copper produced in smelting was refined by gaseous oxidation and reduction methods to rive a product equal in quality to fire-refined copper. The cement copper used in the study was typical of the material produced in commercial operations. The sample product was received in a partially oxidized state and analyzed 77.5 percent Cu, 3.4 percent Fe, 0.8 percent Pb, 0.05 percent Ni, 0.6 percent Sn, and 0.9 percent S. Smelting tests were made on the precipitate using laboratory-size induction and electric-arc furnaces. Three types of furnace linings were tested during, the investigation: Carbon, including graphite; clay-graphite; and silicon carbide. Although all proved satisfactory, either carbon or graphite was preferred because of their superior refractory properties and low permeability to molten copper. Copper recoveries in the induction and arc smelting tests averaged 92 percent in commercial-grade metal assaying 99.8 percent copper. Refining the molten copper by oxidation and gaseous reduction or by chlorine lancing increased the purity to plus 99.9 percent.

Jan 1, 1961

By Richard J. Mainiero, James H. Rowland III, Marcia L. Harris

This paper reviews the potential hazards posed by the toxic fumes produced by detonating explosives in surface mining and construction operations. Blasting operations produce both toxic and nontoxic gaseous products; the toxic being mainly carbon monoxide (CO) and the oxides of nitrogen (NOx). The quantity of toxic gases produced by an explosive is affected by formulation, confinement, age of the explosive, and contamination of the explosive with water or drill cuttings, among others. Techniques to protect workers and the public from the potential hazards of explosive-related toxic fumes are discussed. These include: • Minimizing the quantity of toxic fumes produced. • Determining where the fumes may go so workers and neighbors can be moved out of harm’s way. • Preventing the fumes from moving towards workers and neighbors. • Monitoring the air near workers and neighbors so they can be relocated if fumes appear. • Ventilating structures or confined spaces until CO falls below a hazardous concentration.

By M. N. Plis

This report describes the initial results of long-range research on bit life conducted by the Bureau of Mines. Three commercial bit designs -a round-nose radial, 60° conical, and 90° conical with tungsten carbide (WC) inserts -and five experimental bits were tested. Four of the experimental bits were radial designs using polycrystalline diamond compact (PDC) inserts. The fifth was a 90° conical with an oversize WC insert. Bits were worn on a high-silica sandstone typical of coal mine roofs. The bits were mounted on a 34-in-diam drum section that provided a bit speed of 565 ft/min. Cutting forces were measured on a modified vertical slotter using a three-axis force dynamometer and recorded on an FM magnetic tape recorder. Changes in cutting forces, bit weight, and airborne dust due to gradual abrasive wear and catastrophic insert failure are presented. Tabulated and graphed data, photographs of the progression of bit wear, and selected qualitative visual and auditory observations of the bits taken throughout the experiment are found in the appendixes. The results show that bit life ranged from approximately 16,000 ft for the WC round-nose radial bit to over 125,000 ft for a PDC round-nose radial. Performance, in terms of bit life, cutting forces, wear rate, frictional sparking, machine vibration, and noise was in general best with the PDC bits, followed by the rotating WC bits, with the nonrotating WC bits (round-nose radial and locked 60° conical) being the worst. The results show variations in the included tip angles of new conical bits have an insignificant influence on bit performance when the effects are averaged over the life of the bit. In addition, new bits were generally found to entrain more primary respirable dust for a given cutting distance than worn-out bits. It is hypothesized that this is due to the difference in frictional behavior between new and worn bits. The results from these tests are being used in the Bureau's cutting system model (CSM).

Jan 1, 1988

By D. W. Frommer

As one phase of a general problem of recovering sulfide slimes, mineral-dressing research was conducted on flotation tailing from the St. Joseph Lead Co., Bonne Terre, Mo., mill to recover a significant portion of the residual, finely divided galena. Production of a high-grade concentrate was not part of the immediate objective. Only a reasonable ratio of concentration of lead sulfide slime was sought, since the problem of upgrading by mechanical or extractive processes would be considered in the later stages of this study. The results show that, from a feed material averaging 0.20 percent lead (about 70 percent finer than 400-mesh), a recovery of up to 45 percent could be effected by flotation in rougher concentrate analyzing up to 6.5 percent Pb. These results were obtained by using larger quantities of various xanthates and sodium sulfide than used customarily in mills. Sodium sulfide, which is ordinarily detrimental to flotation of galena, was beneficial in this case.

Jan 1, 1959

By S. J. Pearce

The Bureau of Mines has prepared, as circumstances have dictated, a series of schedules setting forth the minimum requirements that various types of equipment should meet to be considered safe and satisfactory for use under certain hazardous or unhealthful conditions. These schedules cover a wide variety of devices ranging from explosives to electrically operated mine locomotives. This paper discusses the functions and operations of schedules under which respiratory protective devices are tested and approved. It emphasizes that the aim of the Bureau respirator-approval system is to make available to the public respirators that meet definite performance requirements. The responsibility of the respirator manufacturer in pre-testing the device and in maintaining its quality after it is approved are explained. Aid is provided for the user in selecting the proper device for specific application, and a plea is made for better education of all concerned in the proper use of the devices. DISCUSSION Provisions have been made for testing and approving the following types of respiratory protective devices: Self-contained breathing apparatus,2/ supplied-air respirators,3/ gas masks,4/ dispersoid respirators,5/ and chemical-cartridge respirators.6/ These devices are tested at the Central Experiment Station of the Bureau of Mines in Pittsburgh, Pa. Self-contained breathing apparatus is tested by personnel of Health and Safety District B; other types of respirators are tested by the Branch of Health Research.

Jan 1, 1957

By R. R. Sayers

The contemplated use of dichloro-difluorco methane in domestic and commercial refrigerating appliances and in air-conditioning equipment for public buildings and possibly homes, brims attention to the health hazards involved in a wide potential exposure of the public to vapors of another new product, and for the first time to vapors of an organic fluorino compound. The objective in the development of this new refrigerant, however, has been the mitigation of health and explosion hazards in automatic refrigeration, and accordingly these factors have been given primary attention. Early in the development, the Bureau of Mines as requested to make a laboratory study of the toxicity and potential hazard, and it was ca the oasis of the results is of this work and the results of a preliminary investigation made in another laboratory6 that the compound has been selected for commercial use. The investigation conducted by the Bureau of Mines is still in progress, enough information has been obtained to indicate the order of the toxicity and the magnitude of the health hazards involved in the use of dichloro-difluoro methane as a refrigerant. The following is a summarized report of the work completed to date:

Jan 1, 1930

By N. S. Dalal, X. Shi, V. Vallyathan

"Electron spin resonance (ESRJ spectrum of the hydroxyl (· OH) radical spin adduct with .the spin trap 5,5-dimethyl-1-pyrrolintt-N-oxide has been obtained in suspensions of freshly ground quartz particles. The concentration of the spin adduct (and hence of the • OH radicals) increases with the amount of grinding. The dust's potential for the generation of the· OH radicals is maximum when fresh (i.e., immediately after grinding) and decreases to 50% in about a day on storage in air. Studies involving metal chelates .indicate that the • OH radical formation involves mainly the silica surface and H20 rather than the Fenton reaction. The results suggest that hydroxyl radical reaction(s) could be important in the lipid peroxidation and fibrogenicity by quartz dust, particularly .in acute silicosis. INTRODUCTIONIn this paper we report on our electron spin resonance (ESR) detection of the formation of hydroxyl (·OH) radicals in aqueous suspensions of freshly crushed quartz particles. This work was undertaken with a view to find possible clues to the role of free radicals in the pathogenesis of quartz-induced fibrogenicity, commonly known as silicosis. We noted that while silicosis is one of the major health hazards in coal and mineral industries, the mechanism by which the quartz particles exert their toxic action on cells and the process(es) by which these actions progress to fibrogenesis are still poorly ·understood (Reiser and Last, 1979; Singh and .Rahman, 1987). It is generally thought, nevertheless, that the action of quartz particles on the biological membranes is the starting point of the silicotic process (Parazzi et - al., 1968). A possible clue to the mechanism of the membrane damage by quartz particles, in terms of the role of oxygenated free radicals, is suggested by the following observations. A suspension of quartz particles in contact with alveolar macrophages has been reported (Gabor et al., 1975; Koike et al., 1982) to initiate an enhancement of lipid peroxidation, defined broadly as the oxidative deterioration of polyunsaturated components of lipids. Hydroxyl (· OH) radicals are known to be capable of peroxidation by abstracting hydrogen atoms from cell-membrane lipids (Halliwell and Gutteridge, 1985) and of initiating lipid peroxidation in lysosomal membranes. (Fong et al., 1973). Arong other lines, it is known that exposure of cell membranes, fatty acids, and unsaturated food oils to ionizing radiation, which generates· OH radicals, causes rapid peroxidation (Halliwell and Gutteridge, 1985). Thus • OH radicals (and also other oxygenated species such as Oi, 10 2, and H20 2) might be expected to play a role in the toxicity of quartz. Earlier studies of the aqueous chemistry of quartz suspensions have reported detection of H2O 2 (Kalbanev et al., 1980), implicating the formation of ·OH radicals as transient species. However, we are not aware of any report of the detection of • OH radicals in quartz reactions, and thus the present study was undertaken. Since it-is known that, because of their high reactivity (hence short lifetime) in aqueous media, the • OH radicals cannot be detected via ESR directly (Finkelstein et al., 1980; Buettner, 1982) we have used .ESR combined with the spin-trap methodology (Finkelstein et al., 1980) for studying the· OH formation. The results show that· OH radicals are indeed formed in aqueous suspensions of freshly ground quartz; thus pointing to ·a possible new clue to the cytotoxicity of freshly formed quartz particles and thereby to silica fibrogenicity."

Jan 1, 1988

By Albert L. Brautigam, Michael R. Yenchek, Jeffrey Shawn Peterson, James C. Cawley

The National Institute for Occupational Safety and Health investigated how the starting of induction motors may cause nuisance tripping of short-circuit protection on coal mine power systems. This research had a dual purpose: 1) to identify how motor-start waveforms differ from those for short circuits and 2) to devise a method to provide short-circuit protection without intentional time delays to account for motor starts. This technology will help ensure that surface temperatures of energized electrical apparatus will not exceed gas or dust ignition thresholds when short circuits occur.

Bitumninous and semianthracite coal reserves underlie about 1,400 square miles of Arkansas, less than 2.7 percent of the state's total area. These deposits, located near the western border, contain an estimated 2.2 billion tons, of which about half are recoverable. This represents less than one-tenth of one percent of the national reserves. Most of the commercial coal is mined from thin beds that are at least 14 inches thick. In some locations, however, the coal beds can be as much as eight feet thick. Lignite was mined in southern Arkansas before the Civil War. Current estimates indicate that the reserves may be as high as 9 billion tons, which could be used in the state's coal-fired electric generating plants; however, these deposits are not being mined at present. Because many coal operations in Arkansas are small and the demand for coal is unsteady, the industry employs fewer than 25 miners on a daily basis. Arkansas gained primacy when its regulatory program was conditionally approved November 21,1980, subject to the correction of four minor program deficiencies. The regulatory program was fully approved January 22, 1982. Authority of the state to administer its Abandoned Mine Land Reclamation Program was granted upon approval of the Arkansas Reclamation Plan on May 2, 1983. Arkansas was the first state to assume responsibility for abandoned mine land emergency projects when its Reclamation Plan was approved.

Jan 1, 1992

By Edward L. McHugh, Louis J. Denes, Jami M. Girard

A prototype portable hyperspectral imager that operates in the visible and near-infrared ranges of the electromagnetic spectrum was field tested at an open-pit mine. The tests were sponsored by the Spokane Research Laboratory, National Institute for Occupational Safety and Health, as part of an investigation of remote sensing technologies for use in detecting and monitoring conditions in surface mines that could lead to catastrophic slope failure. The spectro-polarimetric imager, built at the Carnegie Mellon Research Institute, employs an acousto-optical tunable filter (AOTF) to control wavelength, a phase retarder to measure polarization signatures, and a digital camera and computer to capture data. The spectral range of the instrument is 450 to 1000 nm at 10-nm intervals. High-resolution hyperspectral images of highwalls, outcrops, hand samples, and drill core were collected in the field. Spectra from the images closely matched those of specific minerals present and were used to classify the images. The field tests were designed to examine the feasibility of using spectral imaging to assist in compiling objective geologic maps of mine highwalls and other hazardous slopes. Results illustrate the capability of the method to discriminate materials within the image, validating the concept of simplified spectral imaging. A contributing factor in many slope failures is the presence and distribution of mechanically incompetent, clay-rich altered rock in slope faces. Spectral features of clays and other minerals are more distinctive in the short-wave and mid-infrared part of the spectrum; the capabilities of the instrument need to be extended into this range to apply the AOTF-based technology to common geologic materials. A field-portable hyperspectral imager could find broad application in remotely identifying diverse materials from solids and coatings to gases.