Search Documents

By Martin H. Stanczyk, I. L. Feld

Continuous open - circuit attrition grinding of a coarse commercial kaolin to produce paper - coating clay , which must have a particle size analysis of 70 percent or more minus 2 - micron equivalent spherical diameter ( esd ) , was studied by the Bureau . The coarse clay , containing about 11 percent minus 2 -micron esd material , was ground in a 10 - inch- diameter attrition grinder using continuous single- and multiple - stage grinding circuits . The clay feed rates varied from 10 to 480 pounds per hour . In some tests , the influence of varying loads of sand grinding media on particle size reduction was studied . Batch grinding tests also were made for comparative purposes . Multiple- stage grinding gave better results than single - stage treatment when equivalent raw clay feed rates were used . In the best test made , a product containing about 80 percent minus 2 - micron esd material was obtained when grinding 60 pounds of raw clay per hour using a three - stage grinding circuit . Power consumption in the test was about 318 kilowatt -hours per ton of clay treated or 475 kilowatt - hours per ton of minus 2 - micron esd material produced .

Jan 1, 1963

By Sam S. Taylor

The disposal of oil-field brines by injection into subsurface formations other than fresh-water-bearing strata is a positive method of eliminating the harmful effects of mineralized water on fresh-water supplies, vegetation, and aquatic and other animal life. The methods used most generally for the disposal of brines produced with oil are (1) impounding in evaporation ponds, (2) controlled diversion into surface streams, and (3) injection into subsurface formations. Various States recognize one or more of the methods as legally authorized procedure. As a general rule, impounding brine in ponds and solar evaporation have not been entirely successful, principally because of the large volumes handled; the porous nature of the soil, and the low rate of evaporation. Likewise, the diversion of brine into freshwater streams by controlled dilution has not proved satisfactory in some areas, especially in parts of Kansas and Oklahoma where the rainfall is relatively low, because it has been impossible to obtain enough fresh water for such dilution.

Jan 1, 1939

By G. R. Hopkins

One of the largest items in the expense of operating a refinery is the cost of the fuel used in distillation and for miscellaneous purposes such as in the heating of buildings and in the generation of electricity, On a B. t. u. basis, the average refinery consumes approximately one-tenth as much fuel as it produces. Theoretically, the fuel consumption at refineries should be much smaller than this, but furnaces can riot be designed to be 100 per cent efficient' and, in addition, a large part of the waste heat is low-temperature heat which would not pay for the expense of recovering it. Annual surveys of fuel consumption at refineries have been made by the United States Bureau of Mines, beginning with 1925. During the 5-year period, 1925-1929, the refineries made steady progress in fuel economy. This is evidenced by the Computed figures of heat requirement Per barrel of crude oil refined, which show a decline from 829,000 B. t. u. in 1925 to 639,000 B. t. u. in 1929 (see fig. 1). In 1930, however, the trend in fuel economy was reversed and the quantity of heat utilized in refining the average barrel of crude oil rose to 672,000 B. t. u. There were undoubtedly a number of reasons for the apparent decrease in fuel economy at refineries in 1930, chief of which were the tendency to carry the distillation farther instead of merely topping the crude and a gain in the consumption of waste oils, such as acid sludge, which in actual practice yield less heat per unit consumed than has been theoretically assigned to oil. The consumption of natural as fuel at refineries has declined since 1927, but this has been more than compensated by a rapid increase in the use of refinery or still gas. The total consumption of oil as refinery fuel in 1930 was not much below the 1925 total, but the consumption of coal has declined rapidly, so that in 1930 liquid and solid fuels contributed only 56 per cent of the total heat units- utilized at refineries as compared with 77 per cent in 1925 (see fig. 2).

Jan 1, 1931

By Henry Kreisinger, WALTER T. RAY

The investigation of the transmission of heat into steam boilers is one of several researches now being carried on by the Bureau of Mines that have for their object the testing of methods by which the mineral fuels in this country may be used more efficiently. A better understanding of the laws governing heat transmission into boilers will result in the design of more efficient boilers, and more efficient boilers will reduce waste in the use of fuel. The results of the investigations described in this report indicate that the conductivity of the heating plates of steam boilers is so high that the present steaming capacities can be tripled or quadrupled by forcing over the heating surfaces three or four times the weight of gases now passed over them. With well-designed mechanical-draft apparatus this greater weight of gases can be forced through the boilers at a small operating cost. It is possible to increase the capacity of many of the present boilers in this way without reducing their efficiency much; in fact by a proper arrangement of the heating surfaces the efficiency can be made higher than the present rating. The efficiency of any boiler can be increased by arranging its heating surfaces in series with respect to the path of hot gases. New boilers of high efficiency can be constructed by making the cross section of the gas passages small in comparison with the length. In Bryan Donkin's book, entitled "The Practical Physics of the Modern Steam Boiler," it is stated that James Watt obtained nearly as good an evaporation per pound of coal and per square foot of heating surface as is obtained now. The remark is probably true. At any rate, about the only decided superiority of the modern steam boilers over older types is in mechanical construction, and for this superiority credit should be given to the designers of machine tools quite as much as to the boiler engineer. The main reason for tardi- ness in boiler improvement probably lies in the reluctance of educated engineers to do the dirty and disagreeable work involved in boiler tests.

Jan 1, 1912

By M. K. Larson, B. G. White

Researchers at the National Institute for Occupational Safety and Health (NIOSH) are investigating the causes and mechanisms of roof failure in underground mines. It is expected that a better understanding of these causes and mechanisms will lead to better layout and support designs that will help prevent accidents and fatalities associated with fall of ground. Two numerical experiments were conducted by NIOSH researchers using the Fast Lagrangian Analysis of Continua (FLAC) computer modeling program with a strain-softening continuum to simulate fracture zones. Two models, one of a round hole in a plate and one of a rectangular opening, were constructed and boundary conditions were applied to simulate far-field shear. The Particle Flow Code in Two Dimensions (PFC2D) computer program was used to look at the effects of far-field shear in generating fractures around an underground opening, but these models are preliminary until boundary conditions, strengths, and stiffnesses are matched to the FLAC models. Results showed that shear zones propagated from the opposite corners of openings in directions that appeared to be determined by opening shape and far-field stress. Tensile failures also formed and extended away from these shear zones. The consistent direction of shear deformation with respect to far-field shear provides a plausible explanation for preferred directions of shear as seen in geologic environments.

By N. C. Tomoeda, W. D. Bensema, J. W. Adams

Measurements of surface magnetic field noise were made at various locations over the Geneva Coal Mine near Price, Utah, on June 12, 1973. The locations selected were on the surface over emergency locator beacons underground at depths between 350 meters (1150 ft .) and 488 meters (1600 ft .) . The surface terrain where these measurements were made was mountainous, and access was difficult. There were no power lines within several miles, and the weather was clear; therefore, the magnetic noise levels were about as low as will normally occur. Results of measurements of distant sferics indicate rather sharp cutoff frequencies below which broad- band, impulsive noise is attenuated. The mechanism of propagation for this noise above the daytime cutoff frequency of 3500 Hz and the nighttime cutoff frequency of 1700 Hz is deduced to be a waveguide formed by the D or E layers of ionosphere as an upper plane and the earth as a lower plane. The measurement systems used are similar to those used earlier. The technique is to record broadband, analog signals, digitize the data, and use a fast- Fourier transform to obtain spectral plots. This tech- nique is novel in that it can measure simultaneously all magnetic field energy within a limited portion of the spectrum for a limited time, and, after processing, reproduce the events occurring in that time interval in great detail .

Jan 6, 1974

By J. P. Schmid

Results of a comprehensive investigation of the impact of underground mine waste disposal on the health and safety of miners are presented. Information was gathered through an extensive search of American and foreign literature and personal communication with professionals in private industry and government. All conceivable health and safety hazards directly or indirectly related to underground mine waste disposal are analyzed, catagorized, and ranked on an industry-wide basis. Positive health and safety effects are analyzed and ranked in a similar way. Both potential and known hazards and positive impacts are included. Recommendations on abatement techniques for the various hazards are presented. Case histories of a fill-related accident in a metal mine and a health hazard associated wtih coal waste backfilling are included and causes and possible abatement procedures are discussed. The rule of management in the promotion of health and safety in backfilling operation is discussed.

Jan 1, 1982

By Jeffrey M. Listak

The Bureau of Mines has conducted a rock mechanics study to monitor deformation of near-seam strata above a longwall panel in the Pittsburgh Coalbed. The primary goal was to determine the height of caving immediately behind advancing longwall face supports. This study, although site specific, provides information on the caving mechanism associated with longwall extractions so that strata behavior and its interaction with longwall face supports can be better understood. Two holes were drilled, approximately 550 ft apart along the center line of a longwall panel, from the surface to the coalbed approximately 650 ft below. Various downhole geotechnical instruments were used to monitor strata deformation. In addition, surface elevation surveys were conducted to differentiate between surface and subsurface activity. This report discusses the caving characteristics of the strata as the longwall panel approached and passed beneath the boreholes. Physical property data are also presented to demonstrate the relationship between caving behavior and local geology. Data show that immediate caving of strata above the longwall face occurred at a height less than 23.5 ft and that strata behavior above longwall extractions is highly dependent upon lithology, with major disturbances occurring at weak lithologic zones.

Jan 1, 1986

By T. H. Davis

Twelve laboratories from the Western United States and Canada participated in radon progeny intercomparison measurements at the U.S. Bureau of Mines radon calibration facility in March 1987. The participants intercom pared grab-sampling and automated equipment methods at high and low concentrations of radon progeny and condensation nuclei (CN). The objective of this intercomparison was to determine if the measurement procedures and equipment of the North American facilities are equivalent. The sampling results showed good agreement among all participants. The standard deviation for the working level measurements was less than 3.5% for 1.70 working level (WL) and less than 8.8% for 0.21 WL. This relatively good agreement was achieved by using alpha standards calibrated by National Bureau of Standards (NBS) and by closely checking and monitoring airflows.

Jan 1, 1989

By A. B. Whitehead

A spectrographic method for the determination of 18 impurities in cerium is presented. The carrier distillation technique is utilized to separate the spectra of impurities from the complex spectrum of cerium. Metal samples are ignited to the oxide, mixed with silver chloride carrier containing an internal standard, and excited with a 20-ampere direct-current arc. An additional exposure, made after carrier depletion, provides for the determination of refractory elements. Experiments to determine the best carrier, sample-carrier ratio, electrodes, arc current, exposure conditions, internal standards, and any matrix effect are described. The relative standard deviation of the method at the 20- and 200-part-per-million levels is about 25 and 15 percent, respectively. The average relative error is about 20 percent in the 10- to 1,000-part-per-million concentration range.

Jan 1, 1962

By H. H. Fields

The Bureau of Mines is in the process of degasifying a virgin area in northern West Virginia from the base of an 839-foot-deep vertical borehole¬. An in situ gas pressure hole 199 feet long, and seven degasification holes ranging in depth from 500 to 850 feet (average 618 feet) were drilled in an 8-foot-thick virgin Pittsburgh coalbed from the enlarged (14-foot-diameter) bottom of this borehole. The in situ pressure at the back end of the hole and the range of gas and water flows from degasification holes as they were completed and closed off were 203 psi, 79,000 to 257,000 cfd (average 160,000 cfd), and 5 to 8 gpm per hole (average 6.8 gpm), respectively. Twenty-four hours after the seven holes were connected through individual water traps to a common collector for natural venting of the gas through pipes to the atmos¬phere, the total gas and water flows and the in situ pressure dropped, respec¬tively, to 971,000 cfd, 1.3 gpm, and 18 psi. Eighty days later the correspond¬ing values dropped to 529,000 cfd, 0.50 gpm, and 13 psi. After 180 days of degasification, 91 million cubic feet of gas had been removed from the affected virgin area. This represents 60 to 70 percent of the gas calculated to be contained in the area of coal affected by the holes.

Jan 1, 1973

To determine the relative permeability of the soil a series of percolation tests were performed at the three locations of interest at Lanse, i.e., 3C, 03A and strip bank, and KA and KB at Kato. Soil cores were removed to 2, 8, 16, 24 and 32 inch depths with the thin wall sampler tube, each core separated from the next by about fifteen feet. Then two-foot-long thin-wall tubes were inserted into the 2, 8, and 16 inch deep holes and three-foot long tubes were inserted into the 24 and 36 inch deep holes. Each tube was tamped down about one inch further to assure a bottom seal; the tubes were filled with water and the rate of fall was measured. The test is similar to those done for septic tank percolation studies 6; but is not quantitatively related to Darcy's coefficient of hydraulic conductivity because the water can flow in three dimensions from the bottom of the tube. The measurements are dependent on the length of test, since the rate of fall is a function of the head. Therefore, it should be noted that the 24 and 32 inch deep tubes should give faster percolation rates because of the one foot greater head. At locations 03A and 3C the data show a sharp decrease in percolation at increasing depth, Table XV. However, the percolation at 03A and 32 inch depth is much higher than at 3C (0.2 vs. 0.01 inches/hour); the fragipan layer must be deeper at the 3C location since this area does experience a perched water table. On the strip bank the rates of falling head are randomly variable, appearing to be as much dependent on the particular location of insertion as on depth of placement. For example, water drained from the 16 inch tube as fast as it was added, probably into a sub-surface cavity or crevice. At Kato the tubes were more difficult to place because of interference of tree roots. For this reason 2 inch deep tubes were not inserted. These short tests at Kato were inconclusive, varying extensively when the tubes were moved. Field permeability tests were also performed in two (previously described) eight-inch diameter permeater tubes at Lanse and one at Kato. Because the soil is confined inside the tube, hydraulic conductivity can be calculated according to Darcy's flow equation. The high values reported in Table XVI experienced when the tubes were rewetted from a dry surface condition, enable us to conclude that infiltration is faster than the saturated permeability of the soil. In contrast to the falling head percolation tests, these permeability results do not show a high variation between locations.

Jan 1, 1972

By W. P. Yang, L. B. Berger, G. W. Jones

"Any burning carbonaceous material, unless supplied with enough oxygen for complete combustion, will liberate carbon monoxide. Since tobacco in its many different forms consists largely of carbonaceous material, and duo to the conditions under which it is smoked (burned), carbon monoxide should be liberated. That this is true has been shown by Armstrong.***** who found that undiluted smoke from cigars contained in some tests more than 3.00 per cent carbon monoxide, the amount present depending upon the size and closeness of packing of the tobacco during manufacture and on the rate of burning.****** Cigarets gave much less CO, varying from 0.06 to 1.40 per cent. The rate of consumption and carbon content of the tobacco are not g.ven, so that a correlation of the values reported to conditions in closed spaces where people might be assembled are difficult, if not impossible.The Bureau of Mines is interested in the general question of carbon-monoxide hazards from tobacco smoke, mainly with regard to mine ventilation. In non-gaseous mines, especially metal mines, the question arises, whether, if groups of miners are permitted to smoke while working at unventilated faces or entries, would the accumulation of tobacco smoke in these places create an' additional hazards the to carbon-monoxide poisoning. The results should, in addition be of general interest in connection with ventilation of building and inclosed places where people may be assembled and smoking is permitted. The investigation described in this report was made with the above idea in view."

Oct 1, 1923

By J. Gautam, T. Ong, W. E. Wallace, M. Keane, S. Xing, J. Harrison

"INTRODUCTIONOrganics extractable from respirable diesel exhaust soot particles by organic solvents have been known for some time to be direct acting frameshift mutagens in the Ames Salmonella typhimurium histidine reversion assay (Huisingh, et al). Upon deposition in a pulmonary alveolus or respiratory bronchiole, respirable diesel soot particles will contact first the hypophase which is coated by and laden with surfactants. To model interactions of soot and pulmonary surfactant, we dispersed soots in vitro in the primary phospholipid pulmonary surfactant dipalmitoyl glycerophosphorylcholine (lecithin) (DPL) in physiological saline. We have shown that diesel soots dispersed in lecithin surfactant can express mutagenic activity, in the Ames assay system using S. typhimurium TA98, comparable to that expressed by equal amounts of soot extracted by dichloromethane/ dimethylsulfoxide (DCM/DMSO)(Wallace, et al, 1987). Here we report additional data on the same system using additional exhaust soots and also using two other phospholipids, dipalmitoyl glycerophosphoryl ethanolamine (DPPE), and dipalmitoyl phosphatidic acid (DPPA), with different ionic character hydrophilic moieties. A preliminary study of the surfactant dispersed soot in an eucaryotic cell test system also is reported.MATERIALS AND METHODSSoots D4 and D6 were collected at two different times as scrapings from the exhaust pipe of a diesel tractor-trailer immediately after the engine was stopped. Surfactant dispersions were made by ultrasonic probe sonicating 25 mg of commercially obtained DPL, DPPE, or DPPA into 1O ml of O.85% physiological sterile saline (PSS) for 10 min at 40 watts power. For surfactant dispersions, 2.5 mg soot was mixed into 2.5 ml of the appropriate phospholipid dispersion. Mixtures were sonicated by 40 watts sonicator probe for one min, then incubated in the sonicator water bath for 30 min at room temperature; the mixture was then incubated for one hour at 37C while being rotated continuously. Dilution series were made with saline. For solvent extraction, 2.5 mg soot was mixed into 2.5 ml of DCM and incubated in a sonicator water bath for 30 min at room temperature. The sample was then mixed with 2.7 ml DMSO, placed in a dry bath at 45C, and the DCM evaporated under a stream of nitrogen gas until 2.5 ml of liquid remained. Ames salmonella/microsome assay utilizing TA98 for frameshift mutation was used for mutagenicity testing, with and without S9 activation, as described by Ames et al (1975). Unfiltered sample extractions or dispersions were preincubated with tester cells for 90 min at 37C : 0.1 ml of sample was mixed with 0.5 ml of PSS, or of S9 mixture, and 0.1 ml of an overnight TA98 culture incubated samples were then added to 2 ml of top agar supplemented with biotin and a trace amount of histidine, and overlayed onto Vogel-Bonner minimal media plates. After 48 hours incubation at 37C, revertant colonies were counted. Solvent controls were DMSO, DPL, DPPE, DPPA, and saline. Positive controls were trinitrofluorenone (1 ug/plate), for samples not treated with S9, and 2-aminoanthracene for S9 treated samples (2.5 ug/plate). All samples were assayed in duplicate. Sister chromatid exchange (SCE) assay was performed, following Lett, et al (1981), using V79 cells, of Chinese hamster pulmonary fibroblast origin. Stock diesel sample suspensions were made as 10 mg soot/ml DPL suspension, or 20 mg soot/ml in DMSO. Aliquots of these soot preparations were added to 15 ml of culture medium per sample flask to result in concentrations of 25, 50, and 75 ug soot/ml medium. After 12 hours incubation, 200 ul of 25 uM 5-bromodeoxyuridine (BrdU) was added to each flask. After another 35 hours incubation, 200 ul of 10 ug/ml colcemid were added; and the cells were harvested three hours later. Cells were swollen by hypotonic saline, and fixed twice with methanol/acetic acid, and burst on microscope slides. Cells on the slide were stained with Hoechst 33258, exp"

Jan 1, 1990

By W. H. Somerton

Many oil-producing formations contain significant amounts of clay. Because of the large surface area and reactivity of such surfaces, the response of the formations to various recovery processes may be dominated by the reactions of fine-grained minerals, including clay minerals, in the formations. Thus, the success or failure of enhanced oil recovery (EOR) methods may be controlled to a large extent by the amount and nature of these minerals in the formations to which the methods are being applied. One of the deterrents to the successful application of chemical EOR methods is the loss of chemicals injected into the formation, to non-oil recovery processes. These chemical loss processes include adsorption onto mineral surfaces, chemical reactions with rock and fluids in the formations, possibly leading to precipitation and plugging of the formation, and trapping of chemicals in parts of the rock structure so that they become unavailable for displacing oil. Chemicals that may be injected include surfactants, polymers and caustic solutions which react with organic acids in the crude oil to produce surfactants in-situ. These losses are most pronounced in fine-grained reservoir rocks containing substantial amounts of clays.

Jan 1, 1984

By Paul L. Campbell

Investigations by the Federal Bureau of Mines of methods of upgrading tar obtained by low-temperature carbonization of lignite showed that ß,ß?-oxydipropionitrile, ß,ß?-iminodipropionitrile, and ß,ß'-thiodipropionitrile were effective solvents for extracting aromatics (aromatic hydrocarbons plus polar compounds) from coal-tar neutral distillate fractions. Batch extraction showed that these solvents extracted approximately the same percentage of aromatics from various neutral oil fractions boiling between approximately 170° and 350° C. In continuous countercurrent extractions using oxydipropionitrile and iminodipropionitrile, approximately 30 to 35 vol.-pct, and 65 to 70 vol.-pct, of the aromatics in 170° to 350° C. neutral distillate oil were extracted at room temperature when solvent-to-oil ratios were 2:1 and 12:1, respectively. As the concentration of aromatics in the neutral distillate oil fraction decreased, the capacities and, to some extent, the selectivities of these solvents for the remaining aromatics decreased. Aromatics were isolated from the extracts and the solvents recovered by washing the extract fractions with a low-boiling paraffinic hydrocarbon such as heptane, using hydrocarbon-to-extract ratios of at least 2:1. The heptane wash removed most of the aromatics but only part of the polar compounds (compounds containing oxygen, sulfur, and nitrogen) from the extracts. The recovered oxydipropionitrile and iminodipropionitrile, containing polar compounds, were effective in extracting aromatics from neutral distillate oils. The contaminated solvents showed essentially the same capacities and selectivities as the pure solvents.

Jan 1, 1961

By L. Nahai

Iran's petroleum industry is nearly 50 years old and the oldest in the Near East. According to published figures, Iran ranks third in production and reserves in the Near East. These reserves (including probable reserves) are estimated at 35 billion barrels and constitute about 11 percent of the world's total. Iran is the sixth largest producer of crude petroleum in the world. The 1961 output of more than 430 million barrels was 5 percent of total world output for the year. In the same year, Iran ranked fourth among world petroleum exporters, providing 8.4 percent of total world exports.

Jan 1, 1963

By L. Nahai

Iran's petroleum industry is nearly 50 years old and the oldest in the Near East. According to published figures, Iran ranks third in production and reserves in the Near East. These reserves (including probable reserves) are estimated at 35 billion barrels and constitute about 11 percent of the world's total. Iran is the sixth largest producer of crude petroleum in the world. The 1961 output of more than 430 million barrels was 5 percent of total world out-put for the year. In the same year, Iran ranked fourth among world petroleum exporters, providing 8.4 percent of total world exports.

Jan 1, 1963

By Jerry Bennett

This report describes the results of a survey of current blast area guarding procedures at surface and underground metal/nonmetal mines. It features five case histories (two surface and three underground mines) of blast guarding methods considered to represent the best systems in use in the U.S. Mining Industry. Elements of an effective blast guarding system are presented along with recommendations for improvements in current blast guarding practices. Industrial and military surveillance and detection technology was reviewed to determine if parallel technology exists for immediate application to blasting site security. While it is concluded that immediate transfer of industrial security technology will be limited, a number of recommendations are advanced for new research to adapt some of that technology for application to the mining environment. Two research areas considered to offer the most potential for improved blast guarding are presented. They are, computerized personnel tracking and blast area intrusion detection using infrared, microwave or E-field type detection systems.

Jan 1, 1981

By Frederick C. Trutt

A guide to the utilization and development of extensions and modifications to the APL Mine-electrical-system Load-flow Program is presented. These modifications include the development of algorithms to minimize computational operations within the iterative-solution techniques, as well as minimization of the number of required iterations. Extensions to the load-flow program include the development of algorithms for the calculation of balanced faults, simplified specification of fault parameters, optional inclusion of pre-fault currents, and an alternate-solution technique.

Jan 1, 1978