Search Documents

By David R. Alison

This study was conducted using field interview methods to determine the data and information requirements of the underground coal mining industry for improving mine ground control procedures in existing and future mines. The establishment of a central geologic and engineering information resource center with computer searchable abstract files that can locate and supply descriptive and case-study literature addressing specific mining problems is recommended. Research done under Bureau of Mines Contract J0395010, includes a Bibliography of Underground Coal Mine Ground Control Literature.

Jan 1, 1980

By Tom Tallone

In the majority of metal and nonmetal mining operations, narrow vein deposits are being mined with slusher hoists. Thin; method of mucking is costly, due in part to its inherent labor intense operation and to its inability to muck 100 pct of the deposits. Mechanized equipment would greatly improve the material handling in narrow vein mining and would dramatically reduce the operational cost. The Compact Loader/Trammer, known as the "mini-mucker" has been developed to increase productivity of the load/haul/dump portion of the typical narrow vein mining cycle. This is Volume II of the final report and concerns the operation and maintenance of the mini-mucker. Volume I covers a general and design review of the activities on the subject contract and are available under separate cover.

Jan 1, 1985

This Information Circular from the National Institute for Occupational Safety and Health (NIOSH) documents and supplements the information presented in a series of workshops held during 2002 and 2003. The primary intended audience consists of all who are involved in developing and conducting miners' training. According to the Mine Safety and Health Administration (MSHA), mine operators reported 240,000 full-time equivalent workers and independent contractors reported 42,000 full-time equivalent workers working on mine property during the year 2000. Unfortunately, these workers have a relatively high risk of suffering serious work-related injuries and illnesses. The mining industry has the highest rate of occupational fatalities among all U.S. industries. The fatality rate is 30 deaths per 100,000 workers compared to 4.6 for all private industry (Morbidity and Mortality Week Report, 2001; NIOSH, 2002). Compared to workers in other industries, miners also have a relatively high rate of nonfatal lost-time injuries, and their injuries tend to be more severe (Bureau of Labor Statistics, 1999). Many miners are also exposed to significant health hazards, including coal and silica dust, diesel exhaust, and noise. More than 1000 U.S. miners die of lung disease each year (NIOSH, 1999). Mine safety and health professionals have long recognized training as a critical element of an effective safety and health program. Federal regulations (30 CFR, Parts 46 and 48) require mine operators to provide initial safety and health training to all new miners, as well as a minimum of 8 hours of refresher training each year. The time and money being spent to train U.S. miners is substantial, and so there is a strong and steady demand for new and better mine training materials and methods. A growing concern among mine safety professionals regards the training of new workers. A major change in the mining workforce is anticipated within the next decade. In major segments of mining, especially coal, relatively few workers have been hired since the 1970's. Thus, as an entire cohort of miners in the current workforce nears retirement, the replacement of these employees will require an influx of new workers. New miners may be young people who lack the ability to recognize and respond to mining hazards in an appropriate manner. They may also have had different educational experiences than their older counterparts. Many safety professionals believe that these two cohorts require different approaches to training. The papers in this report should help prepare mine trainers for the changes about to occur in the workforce and acquaint them with strategies they can use to enhance the effectiveness of their training. The first three papers present basic principles for teaching adults. The five remaining papers are intended to illustrate how these principles can be applied to the development and imple¬mentation of effective training for miners. Below is an overview of these papers. 1. Kowalski and Vaught review the process and principles of adult learning. The learning model they present includes a discussion of goals, content, delivery, assessment, and remediation. Adults are viewed as active learners, experienced-based, expert in their own right in specific areas, independent, real-life centered, task-centered, problem-centered, solution-driven, skill-seeking, self-directing, and internally and externally motivated. Basic aspects of curriculum development are briefly reviewed. For further information about adult learning, see Camm and Cullen's paper. 2. Mallett and Reinke's first paper discusses issues related to training new miners who have recently or will soon be entering the mining workforce. These new generations of miners have different learning style preferences and training needs than Baby Boomers and other older miners. Even trainers who have been highly effective in the past should reassess their training styles and their classroom materials to determine if they are prepared to meet the needs of these young new workers. This paper provides information that will help mine trainers communicate across the generation gap. 3. Mallett and Reinke's second paper provide an overview of training evaluation. Trainers and decision-makers are given a framework for planning and assessing training evaluation strategies. The authors present Kirkpatrick's (2001) model of evaluation categories and discuss how to start an evaluation plan and various ways to collect data. They do not provide detailed instruction in evaluation methodologies, but give trainers a review of the things they need to consider when developing an evaluation plan. A good evaluation plan can inform revisions to a training course, assess trainee learning, and/or answer managers' questions about program effectiveness. 4. Brnich, Derick, Mallett, and Vaught discuss a technique for incorporating worker participation into fire prevention and safe equipment operation training. This technique involves development of short (5 to 7 minutes) videotapes coupled with toolbox talks that ground the content of the videos within the context of a miner's workplace. An example of one of these training modules is presented, along with the results of an evaluation performed on its effectiveness at improving miners' understanding of what types of information they should be sure to communicate during a mine emergency. 5. Wiehagen, Conrad, Friend, and Rethi discuss on-the-job training (OJT) as a method for teaching miners safety and production skills. Much of the training is done by experienced workers. This paper describes how small investments can help improve the effectiveness of on-the-job training. Effective on-the-job training involves some structure and planning in the transfer of responsibility for task performance from the trainer to the novice. Assisting the trainer could involve helping develop up-to-date job analyses and offering strategies for teaching and evaluating job skills. This paper addresses organizational considerations supporting structured on-the-job

Jan 1, 2002

By K. J. Liles

The Bureau of Mines conducted laboratory semicontinuous and continuous heavy liquid tests to determine the feasibility of producing commercial-grade products from the high-clay sylvinite ores of the Permian Basin in New Mexico. Continuous test operations demonstrated that concentrates containing 59.9 percent K2O and recoveries of over 75 percent of the contained potash can be obtained. The organic heavy liquid was effectively recovered by vaporization, condensation, and absorption methods. Less than 5 parts per million of heavy liquid vapors were released to the atmosphere. This loss represents only 0.02 pound of heavy liquid per ton of ore treated.

Jan 1, 1973

By T. C. Woo

This report describes the program that studied the theoretical and practical aspects of the belt cleaning systems, investigated-the possibilities of a self-replacing and/or sell-adjusting belt cleaning device, and designed a horizonal pentagonal turret setup for the underground mine belt conveyors. This design resulted from comprehensive literature survey (both academic and commercial), actual mine visits, study of the mechanics of belt cleaning and bench-type experiments. It has complete working drawings and rough cost estimates.

Jan 1, 1977

By L. C. IlsLey

The Bureau of Mines has collected field data and made laboratory investigations of trailing- cable performance in the hope of developing a better and safer cable for use with permissible mining machines . Because of their better insulation and performance , only rubber- sheathed cables were finally considered . The cables tested represented the product of six manufacturers . : After consideration of the results of the preliminary investigations , the conditions under which cables are used in mines , and the better performance of the later types of cables that were submitted as the investigation progressed , the bureau formulated a performance - test requirement and notified the cable manufacturers as follows : The hazards of the trailing cable are such that the bureau has been unable to extend beyond the machine its formal approval to cover the cable as at present developed . However , in the attempt to reduce the hazard as much as possible , cables passing certain tests will be recommended for this service and it is hoped that several cables will be developed to meet this requirement .

Sep 1, 1930

By Kenneth B. Higbie

METALLURGICAL ACTIVITY in 1963 was again dominated by the insatiate demands of research and development conducted in conjunction with the nation's defense and aerospace programs. An increasing effort was noticeable throughout the year, however, to apply to the commercial field many of the processes and techniques that have been developed by government-sponsored research. Particularly effective has been the Industrial Applications Program of the National Aeronautic and Space Agency through which many of the technological advancements made during the course of NASA research and development have been published and released to the public. POWDER TECHNOLOGY Powder metallurgy techniques for fabricating metals, not long ago declared outmoded because of improved casting and shaping methods, have since made an astonishing comeback. Traditionally mechanical pressing of powder shapes has been employed when melting and casting was difficult or impossible, when phase relationships needed to be sidestepped, or when machining costs could be avoided. Hence, it has long been used for producing relatively small special shapes of high-melting metals and alloys. Small iron parts produced with a punch and die have been common for many years, but powder metallurgy techniques are now applicable to a wide range of materials and items. Hard-to-handle materials including refractory metals and their alloys are now rolled, forged, or extruded from billets made by sintering isostatically compacted powders. The major element of the powder metallurgy industry still comprises iron shapes, however, and two-thirds of the annual 100,000 tons of powder metallurgy products are made of iron. The largest single user of powder-forming techniques is the automobile industry which currently consumes 14,000 to 16,000 tons of iron powder per year. A typical 1963 model auto contained more than 100 pressed powder parts (e.g., transmission gears, timing gears, sprockets, ball joint suspensions) totaling 5 to 7 pounds per car. Some of these powders are used in self-lubricating parts of porous copper and copper alloys containing as much as 20 volume-percent lubricating oil. The expanded use of powder techniques, coupled with

Jan 1, 1964

By Robert P. Apa

Energy Incorporated has prepared this final report presenting the results obtained from the program for extracting alumina from anthracite culm along with the recovery of energy. This work has been accomplished under the auspices of the U.S. Bureau of Mines with technical coordination through the bureau's Reno, Nevada facility. The objective of this program was to develop a process to recover alumina and energy from Northeastern Pennsylvania anthracite mining waste. The program included Identification of sufficient resources to support a commercial facility, identification of the operating parameters which maximize alumina and energy recovery, the development of a conceptual process design, preparation of material and energy balance(s), and the performance of a system economical analysis. The program was conducted in three major phases. In the first phase the program concentrated on selecting several anthracite culm banks capable of supporting a commercial alumina producing facility. The chosen banks were then sampled and analyzed leading to the selection of two banks which were chosen far testing. The Harry E. and Eckley culm banks were the ones selected. Material from these banks was tested in Energy Incorporated?s Idaho Falls, Idaho testing facility. Parametric testing was accomplished in an eight-inch-diameter fluidized bed test facility. The test program consisted of twelve separate tests. After critical operating parameters were determined, the second phase started: process development in EI's 18-inch fluidized bed test facility. Three material and energy balance tests were completed in this facility. Following these tests a 72-hour demonstration test was performed. The data acquired from these tests were used in the last phase: the process conceptual design and economic analysis. The design basis was a commercial scale facility capable of producing 500,000 tons of alumina per year for 15 years. Based on the test program, It is technically feasible to build and operate such a plant today. The facility would produce, along with the alumina, 81.5 MWe of electricity for outside consumption. A preliminary rate of return indicates that the plant is not feasible with today's economic conditions. An increase in the market price of either the alumina or the electricity is required to provide an attractive rate of return for the facility.

Jan 1, 1982

By James C. Barker

Unverified reports of rare earth element (REE) concentrations in gold placers and radioactive mineral prospects in the Zane Hills were investigated by the U.S. Bureau of Mines as part of the Alaska critical minerals program. REE is reported to occur in dredge concentrates at the Hogatza mine and up to 1.2 pct REE was previously analyzed in alkalic syenite (bostonite) dikes marginal to the pluton. In addition, numerous thorium-rich veins, explored for their uranium content but unevaluated for REE, occur on the western margin of the Zane Hills. The Bureau mapped and sampled all of the reported or suspected REE occurrences. Dredge concentrates contain abundant uranothorianite, a mineral species which incorporates cerium subgroup REE. Bostonite dikes occur in conjunction with a multi-phased zoned alkalic intrusion, however, no significant REE concentrations were found. Thorium-rich veins contain nil to 0.5 pct Y but resource potential is limited by this relatively low grade, the ultimate low tonnage potential, and the lack of uranium as a major economic element. The Zane Hills exhibit attractive exploration targets for uranium deposits, primarily in a sedimentary form. Gold may be found peripheral to the pluton in both placer and lode deposits. Resource potential of REE, however, appears limited to a placer by-product of REE-Zr-Ti that is recoverable only during large scale gold placer mining. Placer exploration of the lower Wheeler and Dakli Creeks is suggested.

Jan 1, 1991

By R. V. Ramani

This volume is the first of a four-volume final report on research carried out under a contract from the U.S. Bureau of Mines on the development of a computer simulation model for surface mine reclamation planning. The other volumes are titled as follows: Volume II: Dragline Model, Volume III: Mine Coordinate Generator System, and Volume IV: User's Manual for OPMHS/2. This report deals with the development of a geological model for surface mine planning. The most common orebody modeling techniques are described. A brief review of geostatistical theory and concepts is presented. A geostatistical option for orebody modeling is developed and validated. Computer programs and sample outputs are appended.

Jan 1, 1985

The selective placement of coal stripmine overburden is examined. Physical and chemical properties of spoil detrimental to revegetation and groundwater are detailed. The United States is divided into regions or similar problems. Five mining methods already used in the industry, that are capable of selectively handling waste are examined in detail. Technical and economic comparisons are made for the systems when applied to realistic mine settings. The same analysis is conducted for five novel methods capable of selectively handling waste. Comparisons are made between novel and existing methods. Suggestions for new and modified equipment are outlined. Recommendations for further research are provided. This volume contains all Appendices to the report.

Jan 1, 1981

By (NIOSH) Publication

In 2004, a total of 2,011 coal mining operations reported employment to the Mine Safety and Health Administration (MSHA). Coal mines comprised 13.9% of all mining operations.

Sep 1, 2007

By Jonisha P. Pollard

In restricted vertical working heights such as low-seam coal mines, workers are forced to assume kneeling or squatting postures to perform work. These postures are associated with increased risks for the development of significant knee pathologies such as meniscal tears and osteoarthritis [1,2]. Previous research has shown an increased applied knee flexion moment when kneeling in high flexion [3]. However, these models have been applied to flexion up to 140° which neglects contact between the thigh and calf which occurs beyond 140°. In addition to thigh-calf contact, when kneeling near full flexion there may be additional contact between the heel and gluteal muscles. To the author?s knowledge, heel-gluteus contact has not been previously investigated, but thigh-calf contact has received some attention. Zelle (2007) reported thigh-calf contact forces up to 30% bodyweight (BW) [4]. Zelle (2009) reported decreased knee forces when accounting for thigh-calf contact [5]. Caruntu (2003) reported erroneous force and moment estimations when thigh-calf contact was neglected from models to determine muscle and ligament forces [6]. In this study thigh-calf and heel-gluteus contact forces were quantified to determine their effect on the externally applied flexion moment in high flexion.

Jan 1, 2009

By M. G. Wallis

This report presents the results of a study to develop a detailed mining method design based on longwall mining with sublevel caving. The method is applicable to low-dipping coal seams 20 or more feet thick such as are found in the western United States. The report covers (1) the development and description of the mining method, (2) evaluation of the engineering feasibility of the design, (3) estimates of productivity and recovery, and (4) an engineering cost analysis and economic feasibility evaluation of the mining method design.

Jan 1, 1977

In 2007, a total of 4,639 stone mining operations reported employment to the Mine Safety and Health Administration (MSHA).1 Stone mines comprised 31.2% of all mining operations. ? Mines producing the primary commodity of limestone (crushed and broken) comprised the largest number of operations (n=2,051; 44.2%). ? Stone mining operations were located in all states and territories except Delaware and North Dakota. ? Pennsylvania had the most stone mines (n=373; 8.0%), followed by Texas (n=352; 7.6%).

Aug 1, 2009

In 2007, a total of 2,030 coal mining operations reported employment to the Mine Safety and Health Administration (MSHA).1 Coal mines comprised 13.7% of all mining operations. ? Bituminous mines comprised 92.4% (n=1,875) and anthracite mines 7.6% (n=155) of coal mining operations. ? Approximately 72% of all coal mines were located in three states: Kentucky (28.4%), West Virginia (22.6%), and Pennsylvania (20.5%).

Aug 1, 2009

The title of this book, The Phoenix of Natural Disasters: Community Resilience is aptly chosen. ?The Phoenix is a mythical bird that never dies; the phoenix flies far ahead to the front, always scanning the landscape and distant space. It represents our capacity for vision, for collecting sensory information about our environment and the events unfolding within it.? (source: The Feng Shui Handbook, feng shui Master Lam Kam Chuen.) There are Chinese, Japanese, Russian, Egyptian, and Native American counterparts of the phoenix. All of these birds are identified with the sun and depicted as rising from the ashes ? living again. This is the essence of a community after a natural disaster ? they live again. The Phoenix of Natural Disasters: Community Resilience is edited by Kathryn Gow and Douglas Paton who have done an excellent job of creating a relatively seamless transition between chapters with different authors. The content is organized well with the first chapter providing an excellent overview of what is to come and each chapter including an abstract clarifying the focus of the chapter.

Jan 1, 2009

By E. Morrice

High-purity lanthanum metal was prepared by electrolysis of La003 in a LaF3-LiF-BaF2 bath at 950° C. The requisite bath temperature for the deposition of molten metal was maintained by supplying the heat as current directly to the electrodes. A current efficiency of about 60 percent was obtained. The lanthanum nodules contained carbon and oxygen as major impurities. The total impurity content was from about 0.1 to 0.2 percent.

Jan 1, 1962

By B. J. Dalton

The Bureau of Mines Helium Research Center has as a long-range objective the development of an equation of state for helium that will allow all of the thermodynamic properties to be calculated within the accuracy with which they are known. If this objective is to be realized, a method of calculation must be known. This report gives the principles of the method we use in such problems. A computer program was developed for predicting these properties, including those at the critical point, that is perfectly general and applicable to any equation of state. To demonstrate the efficacy of our method, this computer program was used to evaluate thermodynamic properties of a Redlich-Kwong fluid in the two-phase region. Expressions for calculating various thermodynamic functions specific for this particular equation of state are derived. Numerical values are tabulated and graphs are presented for all functions calculated. It is shown that for a Redlich-Kwong fluid there are finite discontinuities in (1) the second temperature derivative of the Gibbs free energy or chemical potential at the critical point, (2) the second derivative of the vapor pressure curve with regard to the temperature on passing through the critical point, and (3) the measured heat capacity at constant volume on passing through the critical temperature when the calorimeter is filled to the critical density. It is also shown that the heat of vaporization is infinite for a Redlich-Kwong fluid at absolute zero.

Jan 1, 1969

By M. A. Elliott, H. H. Schrenk, L. B. Berger, John C. Holtz

"INTRODUCTION Among the hazards that may attend the use of Diesel engines in mines, tunnels, or other underground operations the presence of harmful or objectionable constituents in the exhaust gas must receive due consideration to prevent the formation of unsafe or unhealthful working environments in these places. Previous reports of this series have presented discussions of the composition of exhaust gas from engines in proper mechanical condition, 6/ the effect of adding some of the exhaust gas to the intake air of the engine, 7/ the effect of operation in atmospheres containing natural gas, 8/ and the effect on exhaust-gas composition of conditions that influence the characteristics of fuel injection in Diesel engines. In all these studies the properties of the fuels used were in general conformity with specifications usually recommended by the manufacturers of Diesel engines. In evaluating the physiological significance of the various components of the exhaust in these experiments, the toxic or objectionable gases determined were carbon monoxide, carbon dioxide, oxides of nitrogen, and aldehydes. Because of the low sulfur content of' these fuels, compounds such as sulfur dioxide and sulfur trioxide were not determined, although in discussion of the test results attention was directed to the fact that if fuels of higher sulfur content were used, the concentration of such compounds in the exhaust would become a significant factor in establishing the quantity of ventilating air required to furnish satisfactory dilut1on of the exhaust gas in underground working places."

Jun 1, 1943