Search Documents

By C. O. Hawk

Distillable oils derived from coal were desulfurized and hydrogenated at 2,500 psig in a two-step vapor-phase catalytic operation to give a product rich in saturated cyclic hydrocarbons. The first step was mainly a desulfurization at 400 C, the second a saturation at 300 C. One of the oils used as feed stock was from low-temperature carbonization of a bituminous coal, the other was from the liquid-phase hydrogenation of coal in the Bureau's pilot plant. The product from the saturation step was distilled to remove the light ends and high-boiling residue and to recover a fraction having acceptable properties with respect to heating value, density, freezing point, viscosity, and boiling range according to specifications suggested by the Air Force for ultra-high-speed aircraft fuel. Quantities of the fuel fraction available were too small for the thermal stability test approved by the Air Force. The experiments, performed on laboratory scale, comprised mostly a study of the effect of varying the oil feed rate (at constant oil-to-hydrogen ratio) on the yield of the desired fuel fraction. The yield of the fuel fraction made from low-temperature carbonization oil was a little more than 1 percent of the weight of coal carbonized; that from coal-hydrogenation oil was about 12 percent of the weight of coal hydrogenated. A few attempts to do both desulfurization and saturation in one operation with sulfur resistant catalysts, developed for vapor-phase hydrogenation or hydroforming, were unsuccessful. By leaving the low-boiling ends in both feed stocks to desulfurization, another product was obtained: a low-sulfur aromatic cut boiling below 200 C. This material would be suitable as a solvent or a chemical raw material.

Jan 1, 1965

By P. L. Woolf, N. Bernstein, M. M. Fine

Continuous experimentation utilizing a 3- by 36 - foot rotary kiln was conducted to demonstrate the feasibility of simultaneous induration and reduction of magnetic taconite concentrate . Lignite , or lignite - anthracite mixtures , and green magnetite pellets (64.2 percent Fe , dry basis ) were heated in a rotary kiln to about 2,100 ° F. After separation from excess reductant , the product pellets were found to be highly reduced and acceptably hard . A total of 140 tons of prereduced pellets with an average Fe content of 79.0 percent was produced at Minneapolis and smelted in the Bureau's experimental blast furnace at Bruceton , Pa . Two additional supplies of prereduced pellets were obtained from The Steel Company of Canada , Ltd. , Hamilton , Ontario , which contained 83.8 and 91.3 percent Fe , respectively . Smelting of prereduced pellets was compared with that of unreduced pellets obtained from The Hilton Mines , Shawville , Quebec , and from the Erie Mining Co. , Hoyt Lakes , Minn . Blast furnace tests established that a substantial decrease in coke rates and higher production result from the use of prereduced pellets .

Jan 1, 1964

The following are abstracts from papers presented at the 4th Symposium on Respirable Dust in the Mineral Industries and· were produced through research funding under the Generic Mineral Technology Center for Respirable Dust. Full articles appear in the proceedings published in July 1996 in Applied Occupational and Environmental Hygiene. (Volume 11, Number 7). The two addresses included in the proceedings point to the progress, prospects, problems, and perspectives on control of respirable dust and dust-related disease in the mineral industries. The symposium papers deal with respirable dust issues that are longstanding such as characterization, health effects, control of airborne coal dust, new and emerging issues such as iron toxicity, diesel particulates, and sampling. The papers were grouped into the following topics: continuous dust monitoring, encompassing the development of a fixed-site monitor that will provide continuous information on instantaneous and time-weighted respirable dust concentrations; mechanisms involved in the generation of dusts in mine environments, important for dust control at the source; characterization and control of diesel emissions (particularly diesel particulates) in mine atmospheres; mining systems effects and models; dust control in mine working faces and in milling environments; characterization of the physical, chemical mineralogical, and biological properties of the dust and their relevance to health effects and sampling; dust-lung interactions, encompassing results from several biomedical studies dealing with acute and chronic inhalation of airborne dusts and associated lung responses; the role of iron in causing lung injury; and therapeutic strategies for ·the control of pulmonary disease. All papers submitted to the organizers were peer-reviewed. In the proceedings, we have not differentiated among the platform and poster papers; rather, they have been grouped into the above topical areas. Taken together, these papers reveal significant progress in the control of dust generation, characterization of dust, understanding of dust-lung interaction, and mining and milling practices to reduce dust exposure - all essential for reducing dust-related occupational hazards at the workplace.

Jan 1, 1998

By K. K. Kelley

This work is both a revision and an elaboration of Bureau of Mines Bulletin 371, which was published in 1934 and included data available to October 1933. During the intervening years, a large number of new experimental, high-temperature, heat-content data have become available through continuous, systematic efforts of the Pacific Experiment Station of the Bureau of Mines and the Laboratory for Inorganic and Physical Chemistry of the University of Groningen (Netherlands), coupled with various individual investigations at many institutions. In addition, calculations from spectroscopic and molecular constant data have been extended and applied to a wide variety of gaseous substances. This bulletin purposes to collect and correlate all available high-temperature heat-content and specific-heat data for inorganic sub-stances and to formulate tables and algebraic expressions for their representation. It is hoped in this manner to remove some of the tedium of thermodynamic calculations for industrial metallurgical research workers and engineers who often have available only an inadequate library in this field. It is expected also that this bulletin will have value to those teaching courses in metallurgical and chemical thermodynamics.

Jan 1, 1949

"The present and possible futures commercial production of potash from various sources in the United States is discussed below under the following heads:1. Potash from the saline lakes.(a),Nebraska lakes.(b),California lakes.(c),Other lakes.2. Potash as by-product from the cement kilns.3. Potash as by-product from the iron blast furnace.4. Potash from silicate rocks.(a),Feldspathic material.(b),Leucite rocks of Wyoming.(c),Sericite slates of Georgia.(d),Glauconite (greensand) of New Jersey.5. Potash from Alunite.6. Potash from organic sources other than kelp.7. Potash from kelp.In this discussion very little more than passing reference, if any, will be given to those projects which up to date have been de¬veloped only slightly, if at all, beyond the small scale laboratory stage, or for the development of which there appears to be very little financial and technical backing at the present time. Nether or not many of these proposed projects have merit can be determined only by an actual operating demonstration.Generally speaking, the potash industry of the United States has been hardly more than marking time since the armistice. This is, largely due to the fact that the consumers of potash have been expecting that heavy shipments of foreign potash to the United States would be resumed soon at somewhere near the pre-war prices, and they have not been buying domestic potash at present prices for many months. The result has been that domestic producers have been unable to sell their product at even cost and many producers of potash have been obliged to close down. Thu Nebraska lake plants were closed down in February. The California saline plants were operating at below capacity, and the only large alunite plant is closed down. Even the cement plants have little or no inducements to recover the potash being lost in their waste gases, and the production is very small at present."

Jan 1, 1919

Martin Marietta Aluminum, Inc. followed Howmet Aluminum Corp., Revere Copper and Brass, Inc. and Anaconda Co. in lifting August prices of 99.5 percent unalloyed aluminum ingot by 3 cents to 56 cents per pound. Prior to these moves, Kaiser Aluminum and Chemical Corp. raised its June ingot listings by 4 cents to 57 cents and Consolidated Aluminum Corp., 4.5 cents to 57.5 cents. Domestic merchants increased July quotes by slightly more than 1 cent to 51.3-51.8 cents per pound. ARSENIC The Occupational Safety and Health Administration (OSHA) issued new standards, effective August 1, for worker exposure to inorganic arsenic, a toxic substance linked by OSHA to lung and lymphatic cancer. The new standard will limit worker exposure to 10 micrograms per cubic meter of air over an 8-hour period, a drastic reduction from the previous standard of 500 micrograms for a like period. Implementation of the new standards may be the most difficult and costly for copper smelters where arsenic is associated with the copper feed material but problems will also be encountered by producers of arsenic containing products such as for pesticides and herbicides. The new standards allow use of personal protective gear for workers as an interim measure until plant engineering controls can be put into effect.

Jan 1, 1978

By H. G. Skavlem

This paper is prepared the United States Bureau of Mines and is descriptive of methods, practice, and costs at the McIntyre Porcupine Mines, Ltd., Schumacher, Ontario. The property is located in the Pearl Lake section of the Porcupine mining district. It is reached by a branch line of the Temiskaming & Northern Ontario Railway from Porquois Junction. There is also a good motor road into the district. The Hollinger Consolidated Gold Mines and the Coniaurum Mines, Ltd., are adjacent properties. Power for both the mining and the pulp and paper industries in the district is supplied by an extensive development of the water-power resources. Weather conditions are favorable for mining operations.

Jan 1, 1933

By R. B. Tippin

To study continuous operation of the heavy liquid separation (HLS) of minerals, the Bureau of Mines concentrated spodumene from a typical ore. The studies included heavy liquid concentration, removal of the heavy liquid from the mineral products, and recovery of the heavy liquid for reuse. The research program examined the influence of feed moisture, steam consumption, stripping time, and condition of steam. Operation of multiple cyclones in series resulted in spodumene concentrates assaying 92 to 95 percent spodumene and indicated mineral recoveries of 86 to 89 percent. Continuous filtration and steam stripping produced mineral products containing less than I pound of heavy liquid tetrabromoethane (TBE) per ton of material. Problems unique to this process are discussed, including heavy liquid properties and viscosity, toxicity, material handling hazards, and safety precautions.

Jan 1, 1970

By J. Pasini

The Bureau of Mines has investigated novel methods of stimulating petroleum production from reservoirs in the Appalachian Region. An important consideration in applying stimulative production methods is the control and removal of solid precipitates from the boreholes of production wells. Where paraffin-base crude oils are produced, as in the Appalachian Region, the accumulation of paraffin may be particularly troublesome. Paraffin deposition is a major production problem that has confronted the petroleum industry for many years. Although considerable effort has been expended by industry and government, a suitable solution has not been found because of the individuality and complex nature of the deposits. Remedial methods used to prevent or remove paraffin fall generally into four classes: (1) Chemical, (2) physical, (3) operative, and (4) combination. Each class has many subclasses that apply to particular problems in different oil- producing areas. Recently, chemical inhibitors and the sonic pump have assisted operators in preventing and removing paraffin deposits. Because these methods are relatively new, their degree of application has not been completely evaluated.

Jan 1, 1963

By Robert R. Stein

Using an automated drill test fooure, the U.S. Bureau of Mines measured the sound power levels produced by a small, pneumatic, rotary roof drill. A series of tests was conducted to determine (1) the relative effectiveness of several drill muffling schemes and (2) the relationship between drill sound power and pneumatic power supplied to the drill. The influence of rotation rate (i.e., airflow) and feed thrust on the penetration rate of the drill was also noted.

Jan 1, 1989

By Donald E. Redmon

This Bureau of Mines report reviews injury experience in the metallic mineral industries for 1966-67. For each of the years, 27 tables summarize disabling work injuries by department, source of injury, extent of disability, part of body injured, and nature of injury. Correlative information on employment, worktime, and operating activity is also presented.

Jan 1, 1973

By John C. Edwards

The Bureau of Mines developed a mathematical model to predict the oxygen requirements for a miner evacuating a mine. The model accounts for variations in the miner's escape speed with mine airway height, and for the empirically determined expressions for the weight-specific oxygen uptake rate for upright walking, stooped walking (duck-walking), and crawling. A Fortran computer program that is user oriented was prepared based upon the model's constitutive equations. Specific instructions for utilizing the program, as well as applications to miner evacuation from a mine, are presented.

Jan 1, 1986

By R. S. Dean

"It has long been recognized that the properties of polycrystalline substances are not the same as those of single crystals. These differences are especially marked in metels and metallic minerals, and are of greatest practical importance in metal working and ore treatment. The property changes encountered in passing from a metal single crystal to a poly-crystalline aggregate are the same as are produced by cold-working a metal or by the precipitation of a disperse phase. Hence, we may logically assume that the property changes are all due directly or indirectly to the formation of interfacial area or internal surface. Our problem, then, is to ascertain the physicochemical state of the metal atoms at such internal surface and show how this physicochemical condition accounts for the pronounced changes of mechanical, magnetic, and electrical properties that accompany increased internal surface.GENERAL CONCEPT OF INTERNAL SURFACEIn 1678, Huyghens attempted to explain the double refraction of calcite by postulating that crystals were built from a regular arrangement of ellipsoidal particles. Over 100 years later, Abbé Hauy concluded from his studies of cleavage that crystals might be built from small units, but the units were of the same shape as the entire crystal. This idea, which was prevalent in mineralogical thought before the advent of X-ray spectrometry, was discarded when the great success of Bragg made it appear that the chemical atoms were in reality the elements of structure. In the further development of X-ray technique, however, C. G. Darwin, in England, and P. P. Ewald, in Germany, found it necessary to postulate crystal units con¬taining many atoms. The latter gave the name of mosaic crystals to those so constituted. The individual units are supposed to Possess the ideal atomic arrangements revealed by the X-ray but are not oriented with respect to one another."

May 1, 1938

By W. L. Dare

This information circular is one of a series published by the Federal Bureau of Mines in which the methods and costs of producing uranium ore on the Colorado Plateau are discussed. This report describes the three largest company-operated uranium mines of Climax Uranium Co. - the G-1, the Mineral Joe, and the Frank No. 1. Climax Uranium Co., a subsidiary of American Metal Climax, Inc., was [corporated] May 11, 1950, just 2 years after establishment of the domestic uranium program by the Atomic Energy Commission. Twenty-five years earlier Arthur H. Bunker, now chairman of the board, American Metal Climax, Inc., organized and operated the U. S. Vanadium Co. at Rifle, Colo.3/ Soon after Climax Uranium Co. was organized, it entered into a contract with the Federal Government to build a uranium-vanadium processing mill in Grand Junction, Colo. Under the contract Climax leased from the Federal Government certain uranium-bearing lands that had been withdrawn from public entry in 1948. From Minerals, Engineering Co. on June 12, 1950, Climax acquired other uranium-vanadium properties on Calamity, Outlaw, and Monogram Mesas in Colorado and on Polar Mesa and in the Yellow Cat area of Utah. To house the milling equipment, Climax leased the old Grand Junction sugarmill building of the Holly Sugar Co. Milling facilities, based on a then new process developed for treating both uranium and vanadium, were completed, and the plant went into production in 1951.

Jan 1, 1959

By R. D. Eash

The purpose of this research contract was to develop and test a Saran latex modified portland cement concrete lagging to be used as a replacement for wood lagging. The scope of work performed was divided into four phases: Phase I - Engineering Criteria; Phase-! I1 - Design Study; Phase III - Fabrication of Lagging; and Phase IV - Prototype Demonstration Project. Each phase of work was completed and is described in detail in this report. The prototype latex modified concrete lagging developed in this program weighed 52 pounds. When tested in flexure, it supported center point loading of 4500 pounds and under 1/4 point loading it supported loadings of 7000 pounds. Deflections at maximum loading ranged from 1/2 to 1 inch. Maximum deflections exceed 2 inches. The lagging does not exhibit catastrophic failure. Two hundred and twenty of the LMC lagging were produced and shipped to the Bunker Hill Company in Kellogg, Idaho for installation in their mine at the 17 level. The lagging are performing satisfactory after 22 months exposure in the mine.

Jan 1, 1980

By Leo A. Schrider

A prediction for oil recovery from a pilot waterflood in the Kane oil- field, located in Elk, Forest, and McKean Counties, Pa., was made and compared to actual field performance. Water-injection and production histories, well logs, other field data, and results from laboratory tests of core material were used in this analysis. Performance of the pilot waterflood, initiated in January 1963, was predicted using a modified Craig, Geffen, and Morse calculation technique. Maximum recovery from this low permeable, preferentially oil-wet formation was predicted to be about 22,500 barrels of oil after 300,000 barrels of water had been injected into the pilot waterflood area. After additional field data were collected it became necessary to reevaluate the pilot waterflood area. The gas saturation prior to the waterflood was estimated to have been 20 percent, based on an assumption regarding the required volume of water injected to initiate oil production. In view of the actual field performance, a gas saturation of 13 percent is indicated. When this gas saturation and the method originally proposed by Craig and others are used) the predicted results are more representative. In December 1965, field performance was further analyzed using a hyperbolic-decline curve as presented by Arps. Based upon this evaluation method, the pilot water flood in the Kane sand should produce 37,000 to 42,000 barrels of oil with the injection of 300,000 barrels of water into the pattern. By continuing this secondary-recovery project to a reasonable economic limit, ultimate oil recovery may be as much as 50,000 to 55,000 barrels, or 129 to 142 barrels per acre-foot from 36.5 acres.

Jan 1, 1967

By Mildred Nadler, Alvin Kaufman

To aid industry and Government in planning water developments the Bureau of Mines in 1963 canvassed mineral producers to determine water use in 1962. Water use by the mineral industry comprises only 2 percent of the water withdrawn by industry as a whole. The major water-using mineral industries are natural gas processing, phosphate rock, sand and gravel, and iron ore. Analysis indicated the following conclusions: 1. Total water use and new water intake is dependent on the quantity of material processed and the process water requirements of the particular indus- try or commodity. 2. Recirculation is dependent on the processing requirements of a par- ticular commodity, the manner in which the water is used, cooling and condens- ing requirements in certain large industries, the quality of new water intake, and the need to treat new and discharged water. 3. Consumed water is dependent on the quantity of water recirculated, the temperature and humidity in the area, and the proportion of water used for cooling and condensing. 4. A threefold increase in water use by the mineral industry by 1985 is forecast.

May 1, 1965

By R. Karl Zipf, Z. T. Bieniawski

"Researchers at The Pennsylvania State University are engaged in a project to understand the mechanics of respirable size fragment formation in coal. The project is based on the premise that a thorough understanding of the fundamental mechanics of fine fragment formation may lead to techniques for reduction and better control of coal dust problems in mines. Presently, it is believed that the mode of fracture propagation which can range from pure tensile to pure shear or any mixed mode in between and the loading or displacement rate can influence the amount of respirable size fragments that are generated on new fracture surfaces during the fracture propagation process The essence of any coal cutting process is one of mixed mode fracture propagation. To study the crack propagation process, a unique mixed mode testing rig was designed and fabricated. This rig is capable of applying loads to a prenotched test specimen that range from pure Mode I (tensile mode) to nearly pure Mode II (shear mode) or many mixed mode loading combinations. It is also possible to apply different loading or displacement rates to the test specimen. With this rig, it is possible to create new fracture surfaces via the different fracture modes and under various loading conditions.These new fracture surfaces are examined with a scanning electron microscope (SEM) to characterize the amount of structural damage and respirable size fragment formation that occurs during the fracture process. Initial observations suggest that the amount of fine fragment formation and the new fracture surface appearance is related to the fracture initiation conditions, particularly the fracture mode and the loading rate. Mode II loading and higher loading rates seem to generate more structural damage and respirable size fragment formation that Mode 1 loading at slower rates.With the mixed mode test rig, the mechanics of fracture initiation for a single crack can be controlled to better understand its influence on respirable size fragment formation. Such understanding may lead to methods which characterize the tendency of specific coal seams to produce undesirable fine fragments during the fracture process, or it may lead to rational recommendations and design guidelines or coal mining machines which inherently produce less dust.IntroductionAs part of a larger effort to reduce the incidence of coal workers pneumoconiosis (black lung) in coal miners, researchers at The Pennsylvania State University are engaged in a project to understand the fundamental mechanics of fine fragment formation in coal. This project is part of a com¬prehensive research effort within the Generic Mineral Technology Center for Respirable Dust which is jointly administered by The Pennsylvania State University and West Virginia University.The principal source of the coal dust in underground mining is the cutting operation. The U.S. Bureau of Mines (USBM) and various European research organizations have conducted investigations into the mechanics of coal cutting for many years. These studies of airborne respirable dust (ARD) formation have concentrated on empirical studies of the various cutting parameters and their effect on ARD for¬mation. The parameters study include depth of cut, cutting speed and bit spacing.(1,2) Other studies investigated the effect of symmetric and asymmetric bit wear and various bit geometries and designs (3-5) Roepke(6) summarized the principals of proper coal cutting to minimize dust formation by recommending to ""cut at maximum depth (maximum advance rate) at all times, at minimum RPM, with the fewest possible bits, having the lowest possible included tip angle."" Most coal in the U.S. is mined with the continuous mining machine which inherently cannot meet these design recommendations.(3)It is recognized that respirable size dust particles are formed and/or liberated by a fracture process. One extremely interesting and useful study performed very early in the USBM dust re"

Mar 1, 1989

By E. J. Lintner

This paper is one of a series being prepared by the United States Bureau of Mines describing gypsum mining and crushing methods and costs at various operations throughout the United States. These papers are designed to disseminate technical information regarding methods used. The cost tabulations represent local operating expenditures only and not total production costs. It is recognized that publication of total production costs may in many instances cause embarrassment to individual operators as well as to the industry as a whole. On the other hand, operating costs are essential to a technical discussion and study of the methods employed. The attention of the reader is called specifically to this differentiation so that there may be no misunderstanding of the scope of the cost tabulation. This paper deals specifically with the mining and crushing methods employed by Victor Plaster, Inc., Victor, Ontario County, N. Y. The maximum annual production capacity of this company is 150,000 tons of crushed gypsum. The methods and practices employed arc typical of those followed in the gypsum mines in western New York State. The shaft is, perhaps, the deepest and the thickness of the gypsum mined is above the average for the section.

Jan 1, 1937

By Northcutt Ely

This volume summarizes mining and petroleum legislation in 25 jurisdictions of East Asia and the Pacific. Within these jurisdictions, primary attention is given to requirements that must be met in each country for acquisition of rights to permit development of mineral resources. Coverage includes: First, identification of the controlling laws or statutes governing minerals acquisition and reference to the administrative authority; second, analysis of the laws governing mines and quarries and their products; and third, analysis of laws applicable to natural gas, petroleum, and related materials. Where pertinent, sections dealing with historical background or administration have been added. In countries where minerals are subject to control of States or Provinces, those areas are considered separately from the central government.

Jan 1, 1971