Search Documents

By James A. Browning

Following an unsuccessful attempt earlier in the program to develop and market a drill channelling machine, we have designed and tested a new continuous channelling method which reduces operating sound levels to below 100 db. This new method relies on a small diameter oxygen-enriched burner to produce narrow channels. Sound intensities are reduced substantially compared to conventional channel widths. They are further reduced by a water spray directed immediately above the flame. Baffles placed along the top of the channel will reduce sound levels to below 90 db. Cutting rates are greater than those of existing channelling burners with costs per unit of channel area substantially reduced for those cases where oxygen costs are reasonable.

Jan 1, 1981

By W. C. McLaughlin

Under a cooperative agreement, the Bureau of Mines, Magma Copper Co., and ASARCO, Inc., tested backfilled ground support systems at t.wo elevations in Magma's San Manuel, AZ, mine. The tests were mainly for guidance in designing the loading crosscuts of the new ASARCO Sacaton underground mine. Two-piece, wide-flange steel sets for 8-by 8-ft (2.44-by 2.44-m) and 11-by II-ft (3.36-by 3.36-m) openings were designed. Set spacing was 3 ft (0.91 m) and 5 ft (1.52 m), respectively. After erection, the sets were lagged with various test materials. The void between the lining and the ground was backfilled with sand and pea gravel. Instruments measuring strain (used to determine changes in stress) were placed beneath the sets and in the backfill. Results indicate the backfilled sets in the smaller drift (2315 grizzly level, panels 6 and 7) of 8-by 8-ft (2.44-by 2.44-m) cross section are a viable permanent support system, lower in cost than the standard formed concrete. Results are inconclusive in 2615 grizzly level, panels 5 and 6, where wide-flange steel sets were used with 5-ft (1.52-m) long concrete gob lagging of T-design.

Jan 1, 1983

By Oliver Bowles

"Asbestos" is not the name of a distinct mineral species but is rather a commercial term applied to fibrous varieties of several minerals. The origin and significance of names applied to asbestos by early writers are discussed in the section devoted to sources of supply and terms employed in ancient times. VARIETIES The most useful variety of asbestos is chrysotile, a fibrous serpentine the composition of which is expressed by the formula H4Mg3Si209. Chrysotile is characterized by a strength and flexibility that permit the use of the longer fibers for spinning. The bulk of the world production of both long and short fibers, is of this variety.

Jan 1, 1935

By Robert A. Jankowski

"Following passage of the Coal Mine Health and Safety Act of 1969 (Public Law 911173), the Bureau of Mines initiated a research program aimed at controlling respirable dust exposures of coal mine workers. Respirable dust is the dust that gets into, and interacts with, the lungs of those who inhale it. It has long been recognized as a severe health hazard to mine workers. This program has been implemented by a team effort consisting of the Bureau's in-house capabilities, the Generic Center for Respirable Dust, and contractors, as necessary. Over the years, Bureau research has addressed principally three areas:o Compliance with the Federal 2.0 mg/m3 dust standard (1970-76).o Dust control for longwall mining (1976-1983).o More stringent respirable dust standards due to quartz dust (1983-1987).In addition, fundamental studies have been conducted by the Generic Center for Respirable Dust, with emphasis on penetration of dust into the lung. Accomplishments have been significant, but problems remain, as noted later.The Coal Mine Health and Safety Act of 1969, established a 2.0 mg/m3 dust standard for all coal mining operations, underground as well as surface. At the time of enactment of this legislation, the industry was averaging approximately 4.0 mg/m3. The Bureau of Mines respirable dust research program played a significant role in identifying and developing effective technology to allow better compliance with this new standard, thanks to industry implementation and Federal enforcement."

Nov 1, 1988

By Carlton E. Brown

Impinger dust-counting methods are used by industrial hygienists for determining the number concentration of unhygienic siliceous dusts in industrial atmospheres. Various statements have been made regarding the size of the smallest particles revealed by the microscopic employed in such determinations. Published data on the subject are quite limited. This report presents information on the size of the smallest particles revealed by light-field and dark-field techniques applied to impinger and electric precipitator samples collected from experimentally established aerosols of silica dust and bituminous-coal dust. Size distribution and number concentration of particles of the various sizes in the aerosols were determined from samples collected by thermal precipitation simultaneously with the impinger and electric precipitator samples. The size of the smallest silica and bituminous-coal dust particles determined in the light-field counting method used was about 1./1, . There was relatively little variation in the values from 8 impinger and 33 A.-C. precipitator samples of silica dust and 13 impinger and 13 A.-C. precipitator samples of coal dust. The coefficients of variation of the values from the four sets of determinations were low, ranging from ± 7.7 to t 10 percent. This size of 1,14 is close to the limit of resolution of the microscopic method used and to various previously suggested values. The size of the particles determined in the dark-field counting method used was smaller than the size (about 0.28A ) of the smallest particles determined in the light-field, oil-immersion method used for the thermal precipitator samples.

Jan 1, 1951

By James R. Boyle

The mining methods and practices used at the Young zinc mine, American Zinc Co. of Tennessee, have resulted in a low-cost, high-yield operation. Zinc ore (sphalerite) occurs in limestone-dolomite beds of the Kingsport Formation and is mined by modified room and pillar method. Utilizing trackless mining equipment which incorporates a high degree of flexibility, this operation has had a steady increase in productivity.

Jan 1, 1965

By Lloyd M. Kniffin

[This paper is one of series being prepared by the United States Bureau of Mines on mining methods, practices, and costs in the various mining districts of the United States. It describes the mine of the Hanover Bessemer Iron & Copper Co. at Fierro, Grant County, N. M., which is the only operating iron mine in the southwestern part of the United States. This mine is in a district noted for the great variety of ores that it produces. Within a small area, as shown is Figure 1, there are noteworthy deposits of nearly all the common metals. The ore occurs in lenticular masses dipping at about 50°. An underhand stoping method has been developed that requires but a very small amount of handling of ore. As the ore is very irregular in iron content and also in the distribution of the impurities--chiefly sulphur, silica, and magnesia--a method has to be used that will permit selective mining and will also allow ore and waste to be taken out separately as conditions change. A magnetic cobbing plant raises the grade of the ore shipped about 10 per cent.]

Jan 1, 1930

Norton Co., a manufacturer of abrasive products and diamond drilling and coring bits for oil and gas exploration, is building a $19.1 million addition, scheduled for completion in late 1980, to the Huntsville, AL. The plant makes alumina-zirconia abrasive grains used in grinding wheels and coated abrasives. ALUMINUM Martin Marietta Aluminum Inc. announced plans to expand production capacity of its 112,000-ton-per-year primary aluminum smelter at Goldendale, WA to 177,000 tons per year. The $125 million expansion was scheduled to come onstream in 1981. The Aluminum Company of America announced plans to restart a fourth potline during October at its 185,000-ton-per-year Point Comfort, TX primary aluminum smelter.

Jan 1, 1979

By Charles L. Harness

The barite industry has made notable progress since the days when barite was used only as an adulterant in white-lead paints and the only method of mining it was with pick and shovel. The following chronological record may serve to show how this heavy white mineral has grown in importance in the national exonomy and at the same time to indicate development of methods for obtaining it. 1845. - Barite first, mined in Fauquier County, Va., for use as an adulterant in white-lead paints. 1850 (approx.). - French settlers 60 miles southwest of St Louis, Mo., discovered barite; called it "'tiff;' meaning white. It was mined and shipped to St. Louis for use in paint.

Jan 1, 1946

By Alvin Schallis

Of all the uses for dolomite that depend on its magnesia content, perhaps the most important is its use in basic refractories. The quantities of dolomite (including both that used as crude and that calcined before use) sold or used for refractory purposes by producers in the United States for 1920-41, inclusive, are shown in figure 1. As can be seen from the chart, the utilization of dolomite as a basic refractory is far from new; it was, in fact, the first basic refractory used extensively in open-hearth steel furnaces. After large deposits of magnesite were opened in Austria-Hungary, the use of dolomite in the open hearth declined somewhat, only to be actively revived during the World War of 1914 to 1918, when supplies from Austria were shut off. The use of dolomite as a refractory in the steel industry again declined slightly for a brief period after the Armistice, but subsequently its use has tended steadily to increase, latest statistics indicating that more dead-burned dolomite is used per ton of open-hearth steel now than during the World War of 1914 to 1918. Despite fluctuations in consumption, dolomite has continued to be by far the most widely used basic refractory material. The following table, showing the quantities of basic refractories consumed in the manufacture of steel, the principal outlet, indicates the relative importance of dolomite. The chief reason for the widespread use of dolomite as a basic refractory is its relatively low cost. Its abundance and the proximity of the deposits to the steel industry (see fig. 2) afford every incentive to enhance the desirable physical properties of dolomite refractories and to ameliorate certain of their less desirable characteristics. The present emergency, with its huge demands upon the steel industry, has lent further impetus to the work of improving dolomite refractories.

Jan 1, 1942

By J. B. Cunningham

Lithium in the form of metal, salts, and alloys is particularly important because of increasing industrial uses resulting partly from wartime developments. Lithium carbonate and lithium strontium nitrate, which impart a brilliant red color to a flame, are used in pyrotechnics. Lithium chloride and fluoride are used in fluxes for welding aluminum to dissolve the oxide coating on the aluminum and prevent oxidation of the molten metal. Lithium carbonate is used in ceramics in raw alkaline glazes because of its unusual fluxing properties. The use of 9 to 12 percent lithium carbonate permits a marked increase in the amounts of alumina, calcium, and silica that may be Used and results in a more stable glaze with sufficient alkalinity to produce vivid copper blues and other typically alkaline colors. Lithium stearate is used as a grease in airplane engines because of its ability to withstand wide changes in temperature. In view of its great affinity for nitrogen, hydrogen, oxygen, sulfur, phosphorus, carbon, and silicon, lithium has an excellent scavenging action on molten metals. It forms stable nonmetallic compounds of low specific gravity or gases that are eliminated at pouring temperatures. Lithium is generally added to the melt in the form of a lithium-calcium alloy consisting of 50 percent of each ingredient or as an alloy of 98 percent copper and 2 percent lithium. The lithium-calcium alloy added to cast iron before pouring, acts as a scavenger and increases the fluidity of the melt. This alloy also is said to increase the corrosion-resistant properties of stainless steel alloys and to improve their polishing qualities.

Jan 1, 1948

By D. B. Taliaferro

An accurate knowledge of the water content of oil-bearing sands4/ now is recognized as an important factor in calculations of the flow of oil through the sands to producing wells and in the estimation of oil reserves, To this end the Bureau of Mines laboratories are using a method that is an adaptation of the A. S. T. M. method of determining the water content of petroleum products (1).5/ However, the apparatus and technique have been altered slightly, as described in this report, to increase the precision of the method without affecting the simplicity of procedure or speed with which determinations may be made. Until recently petroleum engineers, when estimating reserves assumed that the entire pore volume of the oil-saturated parts of producing sands was filled with oil, as it was generally thought that the oil, water, and gas in any formation had separated completely during geologic time into distinct layers because of their difference in density. In 1929 Lindthrop and Nickolaeff (12) reported experimental results from which they concluded that 22 to 30 percent of the pore volume of producing sands in the Grozay district, Russia, was filled with water when the fields were discovered. Since that time numerous investigators (5, 7, 8, 10) have found evidence of water in the sands of now oil-producing fields and old fields that never produced water with the oil.

Jan 1, 1940

By J. W. Paul

This report is the second of a series of papers on coal-mining methods and costs which are being prepared by the U. S. Bureau of Mines for the purpose of placing before those interested in the industry a knowledge of the mining methods employed in this particular mine, and cost data on the several operations pertaining to removing the coal from the face into the railroad cars at the tipple with economy and safety. The methods employed are influenced by the natural local conditions, with respect to the thickness of overburden, frequency of local "wants," and the means employed for roof support, and its control

Jan 1, 1929

By A. C. Johnson, McHenry Mosier

The Bureau of Mines has adapted its activities to needs of national defense and to conditions brought about by the war program . Its work is now oriented solely to war problems . After studying about 1,600 deposits of war minerals , exploration projects have been undertaken on 96 of the most promising , of which 56 have proved successful . These have indicated that 56 million tons of ore of commercial or near -commercial grade can be utilized to meet war requirements . Included in this amount are 1 million tons of tungsten ore ; 4 million tons of chromite ore, 10 million tons of manganese ore , 2 million tons of antimony ore , 1 million tons of mercury cre , and 28 million tons of iron ore . Work done in connection with exploration projects included 172,000 feet of surface trenching , 210,000 feet of drilling , and 21,000 feet of shaft sinking . Nearly 100,000 samples were taken, on which 500,000 analyses were made . Extensive metallurgical tests were made on ore from many of these deposits , both in the laboratory and in pilot plants , in connection with research to develop metallurgical processes for their treatment .

Jan 1, 1943

By George T. Motock

In Germany the extraction of lithium and its salts has been handled mainly by units of the two major concerns - Metallgesellschaft A, G. and Deutsche Gold und Silber Scheide Anstalt, both with headquarters in Frankfurt. Zinnwaldite, which belongs to the mica group, is the major source of the lithium-containing raw material in Germany. Lepidolite and amblygonite also are used when available, but they are imported, as there are no major deposits of these two minerals in Germany.

Jan 1, 1946

By Harmon E. Keyes

Many organizations, including the Bureau of Mines, have made intensive studies of the application of leaching methods to relatively small low-grade disseminated deposits of copper ores, containing both oxide and sulphide minerals. One of the principal difficulties has been to obtain a solvent that could be made at a low cost and would effectively dissolve the copper minerals. Another drawback has been the high initial cost of a plant and the refined type of mechanism ordinarily required by standard practice for carrying out the leaching cycle. The Bureau of Mines has attempted to develop a cheap and efficient solvent that would especially meet the requirements of smaller plants. (See Bibliography.) It has been known that dilute ferric sulphate-sulphuric acid solution is an excellent solvent for most copper minerals, such as chalcocite, bornite, and oxidized forms, but not for chalcopyrite and certain silicates. A method of producing this solution from sulphurous products and waste liquors was developed by the bureau and tried successfully on a test-plant scale at the Southwest Experiment Station in cooperation with the department of mining and metallurgy, University of Arizona, Tucson, Ariz. However, this work did not involve the actual leaching of ores with the solutions thus produced or the cyclic use of the iron solutions in the regenerator cell. Except for certain laboratory tests, in which known impurities were added, no data were available to show the effect on regeneration if accumulations of impurities were built up in the leaching circuit.

Jan 1, 1930

By F. C. Houghten, R. R. Sayers, C. P. Yalaglou

"Introduction.Atmospheric conditions relative to high temperature and humidity are of great importance in mining, as well as in such allied fields as railroad and vehicular tunnels. An extended investigation into the effect of these factors on men has been in progress for some time, both in the field under actual working conditions, and at the Pittsburgh experiment station of the bureau in cooperation with the American Society of Heating and Ventilating Engineers and the U. S. Public Health Service.For several years one of the writers (Dr. Sayers) and L. Harrington, supervising mining engineer of the bureau, have been studying the effects of hot humid atmosphere in metal mines on the comfort and efficiency of the workers. Some of the reactions experienced in still and in moving saturated mine air at temperatures of 90 to 100°F., with men at rest are presented in a recent paper.****The present paper is based on experiments made under carefully controlled conditions to determine the relative feeling of warmth experienced by men in atmospheres of various degrees of temperature and humidity. The work was conducted by the research laboratory of the American society of Heating and Ventilating Engineers, at the Pittsburgh experiment station of the Bureau of Mines, in special physchrometric chambers built for this purpose. It was carried on under the direction of F. Paul Anderson, director of the laboratory, Dr. R. R. Sayers and A. C. Fieldner of the Bureau of Mines. The results given in this paper are for still air only. Investigations of the effects of moving air are being continued, and will be reported later."

Jan 1, 1924

This report describes the new Bureau of Mines Core Repository System (CORES) and presents the methods for selecting, processing, and storing physical samples and descriptive data for future reference by earth scientists. The system preserves splits of chip samples and longitudinally sliced segments of core. A records retrieval system provides for storage of data on microfilm and magnetic tapes and uses the keysort parameters of location and commodity for the identification of data.

Jan 1, 1978

By A. R. T. Dennues

"INTRODUCTION There are presented in this report the results of limited studies by the Bureau of Mines of the firedamp safety of some powder-powered tools proposed for use underground in coal mines. This study was made to obtain general information and specific technical data for a cable splicer and some rail punches now commercially available, the aim being to keep abreast of developments and to anticipate hazards.ACKNOWLEDGMENTSAcknowledgments are made to the Mine Safety Appliances Co., Pittsburgh, Pa., for supplying equipment for these tests, and to the Pittsburgh Coal Co. for making possible observations of the use of these tools in coal mines.The assistance of other members of the Explosives Division is acknowledged: J. E. Crawshaw, for examination of ammunition and, propellant powders; H. L. Wilson, for analyses of the natural gas used in the gallery and Jerome C. P. Weinheimer and Martin Bashel, for conducting the gallery tests.GENERALDescriptions of the DevicesPowder-powered tools of the type tested utilize the energy of charge of,propellant powder accomplish tasks. They are essentially small guns adapted to special work. Of the family of such tools now commercially available from one manufacturer, two have been proposed for use underground in coal mines, namely a cable splicer known as model TI and two models of rail punch known as R40 and R60. These tools employ blank-cartridge ammunition and special projectiles to accomplish the work indicated by these descriptive names."

Jul 1, 1947

By Phillip W. Holland

The U.S. Bureau of Mines has developed a mass spectrometer method for determining helium in the parts-per-million to 10% range to an accuracy of ± 1%. The method employs a mass spectrometer, an inlet system utilizing a chromatographic gas-sampling valve, and an activated coconut charcoal trap cooled with liquid nitrogen. Gravimetrically prepared standards of helium in nitrogen were used to demonstrate the linearity of the method over the concentration range of 10 ppm to 10.66% helium.

Jan 1, 2010