Search Documents

By N. H. Coates

A small, special-purpose centrifugal compressor was developed to circulate 60 pounds per hour of helium at 1,000° F and 250 psig because standard, commercial units were not available. Performance characteristics of this compressor were determined at helium flows of 2,000 to 18,000 std cu ft per hour, pressures of 100 to 250 psig, and temperatures of 100° to 1,000° F. This range is 2 to 90 actual cu ft per minute. Several graphs show the adiabatic head developed by the compressor over this wide flow range at various combinations of temperature and pressure. A compressor performance map relates pressure ratio to mass flow, temperature, pressure, and speed. This map can be used to accurately predict compressor performance factors within the range of operating conditions covered by the experiments.

Jan 1, 1963

By C. E. Hennig

On January 1, 1959, the United States had 313 petroleum refineries with a total installed crude-oil throughput capacity of 9,819,846 barrels per day, according to the Bureau of Mines annual survey. Compared with a year ago, this represents a net decreased of five in the number of slants mild a net increase in capacity of 412,139 barrels per day. The continued increase in total capacity and decrease in number of plants raised the average capacity of a refinery to a new high of 31,373 barrels per day. During 1958 total capacity increased in every refining district except the Louisiana Gulf district, which showed a 2-percent decrease due mainly to the retirement of the American Oil Company's plant at Destrehan, La. The largest increase, 14 percent, occurred in the Texas Inland district followed by a 12-percent increase in the Arkansas-Louisiana Inland district. At the beginning of 1959 the industry was building facilities that would add 108,400 barrels per day to crude-oil capacity. It also had under construction a capacity of 226,100 barrels per day as replacement. On January 1, 1959, no new refineries were under construction.

Jan 1, 1959

This paper describes the sinking and lining of a 14 foot 6 inch finished diameter shaft down to and into the salt of a typical dome of the Gulf States region. The conditions and nature of the strata encountered divide the work into three distinct sections - that in (1) alluvial surface deposits, sunk through by open caisson methods, (2) water bearing rock, directly above the salt, and in (3) salt. ACKNOWLEDGMENT The writer wishes to acknowledge the cooperation of the sinking contractors, The Dravo Contracting Co. of Pittsburgh, Pa., through E. T. Gott, vice-president, in furnishing the data used in this paper.

Jan 1, 1932

By Robert J. Anderson

"Introductory Statement:In melting the nonferrous metals and alloys for foundry and rolling-mill work, even with the best practice, there is always a loss, due principally to oxidation. Melting losses are a serious source of financial loss in brass and bronze practice, but they are especially serious in the case of aluminum and its light alloys because of the relatively high price of aluminum. The indications are that the melting losses in many aluminum foundries of the United States are at times high, and in some plants (especially where certain furnaces are used) they are entirely too high when compared with the average practice. The fact that the oxidation losses in melting aluminum and its light alloys are high is well known, but it is doubtful whether the factors governing the most suitable methods of melting for a minimum of dross are equally well known. The metal losses involved in melting are worthy of especial attention now because of the rapidly growing importance of the aluminum industry.Factors in the operation of furnaces which affect metal and fuel losses:The essential requirements in the commercial melting of any metal or alloy are that the melting losses should be low, the melting should be rapid, and the melting cost should be low. Certainly it may not be possible to obtain these requirements in any furnace selected at random, and it follows that the design and the operation of furnaces for melting different metals are subjects that warrant the most extensive study and tests. As a general rule, in the industrial operation of furnaces, run on aluminum and aluminum alloys, an effort is made to keep the dross and oxidation losses as low as possible. In attempting to hold dross losses low, numerous factors involved in metal melting may be overlooked, or at least disregarded, and the net practical result may be that the furnace is exceedingly wasteful of fuel. In the case of aluminum and its light alloys, the effect of increasing the temperature of melting, at least in an atmosphere containing free oxygen and nitrogen, is to increase the net melting loss."

Apr 1, 1921

By ALICE V. Petar

Through the courtesy of the State Department, the Bureau of Mines has received a compreensive report on the jede industry of Burma, pre- pared by American Consul Winfield H. Scott, Rangoon, Burza. This mater- ial is the main basis for the present circular, although free use also has been made of reports on the jede industry in China and Germany by consular officers in those countries, to whom footnote credit is given. The word "jade" is said to be derived from the Spanish "piedra de ijada" (hijada) meaning, literally, "stone of the side," as jade was supposed to cure pains in the side; nephrite (a jade mineral) was named from the Greek word meaning kidney, because it was formerly warn as a re- medy for kidney diseases. To the Burmeso, jade is known as "Kyauksein," or green stone, and to the Chinese, all varieties of the material are referred to as "Yu" or "Yu-chi", According to Confucius, jade was symbolical of. justice, harmony, intelligence, and humanity, and the Chinese of today believe that by using ornaments made of this stone, the wearer is. protected from the "evil eye" as well as from diser.se. Ornaments of carved jade were known to the ancient civilizations of Mexico and Peru and to the peoples of other sections. of Central and South America, Jade ornaments also have been found in the lake dwellings of Switzerland and in Crete; thile in China, as far back as the Chou dynasty (B. C. 1122 B. C. 255) it was used in the production of various classes of precious vessels and as insignia of rank.

Jan 1, 1936

By T. R. Rehak

Blasting operations are an essential element in the recovery of our Nation?s mineral resources. The mining industry uses billions of pounds of explosives annually. The majority of blasting occurs in surface mining operations. Blasting results in the fragmentation and often the projection of rocks. Frequently, the rocks are thrown beyond the expected limits. Flyrock and failure to secure the blasting area dominate blasting-related accidents in mining, especially in surface mining. Blasting accidents in the mining industry tend to result in critical injuries or fatalities. Accident reports and information collected from the Mine Safety and Health Administration (MSHA) and other government agencies provide supporting evidence. According to the data collected, blasting-related accidents (in mining) were 11 times more severe than all other types of mining accidents. Blasting accidents are not unique to mining operations - the same situation exists in the construction field. In this paper the authors have compiled a list of the primary causes of flyrock and the failure to secure the blast area. In the next phase of this project, typical blasting scenarios will be reviewed which will highlight the main reasons flyrock and/or lack of blast area security occur. This will alert miners and construction workers to the current problems/hazards associated with blasting and to identify other safety measures to protect personnel.

Jan 1, 2000

By J. R. Thoenen

Occurrences of titanium, zircon, and other heavy minerals are widespread in Florida. Deposits concentrated as "heavy sands" by wave and wind action have been mined an or near Atlantic coastal beaches since 1916. An important inland concentration at Trail Ridge; .believed, to have formed along an ancient share line, was disclosed by preliminary investigations (1947) by the Bureau of Mines. This report describes investigations to determine the extent and grade of "heavy-sand" concentrations in other inland stabilized dune areas in the central and northeastern parts of the peninsular region of the State (fig. 1). Portions of the central highlands south of Trail Ridge and terraces and dunes in the coastal lowlands region, east and northeast of the ridge were investigated. Holes were drilled in 10 areas (see table 1 and fig. 2) along State and County roads and on private property. They were spaced 250 to 2,000 feet. apart to obtain a cross-sectional picture of "heavy-sand" content in the dune areas. These sections were generally placed in east-west directions normal to the general trend Of the peninsula to intercept one or more of the ancient shore lines in the various areas (figs. 3 to 13, incl.). A total of 433 drive piped and 333 jet holes were drilled, and 7,293 bulk and core samples were taken. Intermediate holes were placed at closer intervals when field analysis indicated 1 percent or more of heavy minerals present. All of the holes drilled and the analysis of samples that contain 1 percent or more of heavy minerals are listed in table 2. Profiles (figs. 14 to 20, inclusive) show the more favorable concentrations, which are irregular in outline and erratic in mineral content. The highest concentrations averaged 1.0 to more than 2.0 percent heavy-mineral content, but a few individual hole samples exceeded 3.0 percent in grade.

Jan 1, 1949

By William Seymour

"INTRODUCTION Byproduct-coke manufacture is one of our country's most essential in¬dustries; its importance was strikingly accentuated by the demands of World War II. This paper reviews recent progress in various phases of byproduct-coke operations for the production of metallurgical coke particularly that used as blast-furnace fuel.In the early days of the by-product-coke industry in the United States high-grade bituminous coking coals, both high-volatile or gas coal and low-volatile Pocahontas coal, were plentiful, and the selection and mixing of coals for coke-oven use were minor problems.The demands of World War I for the production of iron, steel, and coke aroused and stimulated new interest in the investigation of the reserves, characteristics, and properties of our coking coals. During that war the increased demand for coke reached a critical stage, and the shortage of high-grade coking coals necessitated the use of cols of inferior quality and of different coking characteristics than those previously used.The period of prosperity following World War I brought much progress and development in the by-product-coke industry. Methods of testing coal and coke were improved. The search for satisfactory coking coals was continued, and construction and design of byproduct ovens were improved."

Jun 1, 1946

By John J. Henn

An evaluation is presented of the Bureau of Mines process for the recovery of metal and mineral values from municipal incinerator residues. This process employs standard mineral beneficiation techniques and is operating on a pilot-plant scale of 1,000 pounds of incinerator residue feed per hour. Products from this separation process include ferrous, aluminum, and copper-zinc scrap, and colorless and colored glass. Cost estimates were prepared for four plant sizes. The estimated capital and operating costs For the four plants follow: [ ] It is assumed that the separation plant is located adjacent to a municipal incinerator. Provision is made, however, for part of the residue feed to be delivered by truck so that one large separation plant can be used for residue from more than one incinerator.

Jan 1, 1971

By H. E. Peterson

A study was undertaken by the Bureau of Mines to develop a simple, reliable test for field detection of selenium in rocks and soils. Two methods are described for qualitative detection of selenium, dependent upon its form of occurrence and the presence of interfering constituents in the sample. Both methods involve fusion of the sample in a test tube to form elemental selenium that will volatilize and condense as a red deposit on the cooler upper portion of the test tube. The methods are sensitive to 10 parts per million, (p.p.m.) equivalent to 0.001 percent, and can be made semiquantitative by using suitable standard samples. INTRODUCTION Although selenium is widely distributed in the United States, the known deposits are either so small or so low grade that they cannot be processed economically for selenium alone-4/ At present, commercial production is a byproduct of the smelting and refining of base-metal ores, particularly copper.5/ About 0.75 pound of selenium is recovered per ton of electrolytic copper, and small amounts are recovered by special treatment of assorted smelter dusts and fume products. Since selenium is a strategic metal in short supply, new sources are being sought by both Government and private interests.

Jan 1, 1957

Measure the leakage through individual crosscut stoppings quickly and economically so that the worst ones can be identified and repaired. (Typically 60 to 80% of the air supplied to a mine short circuits before reaching a working face.) Approach Most of the leakage through a permanent stop-ping is channeled through two windows in a temporary stopping, and air velocities through the windows are measured; leakage is determined from a formula. How It Works A temporary stopping made of plastic brattice is erected in the same cross cut as the permanent stopping, either upstream or downstream. The brattice is fastened to the roof, bottom, and ribs of the entry with spads. Normal leakage of brattice was allowed for in deriving formula, and does not effect results. For best accuracy the brattice and the stopping should be separated by a distance of one hydraulic diameter.

Jan 1, 1979

By Harold L. Gibbs

The purpose of this paper is to encourage petrographers to prepare thin sections, as the demand for microscopic examination of rocks, ores, and metallurgical products is becoming more general in .the mining metallurgical-fields. This paper has been written with the knowledge that the successful thin-section methods and the several new techniques herein described will be helpful to all engaged in this field of work. Detailed instructions for making thin sections by methods developed at the Salt Lake-City laboratory of the Bureau of' Mines are given in this paper. Several new techniques are described for making thin sections of loose grains and fine sands and for making good thin sections of highly altered and friable rocks. The methods described insure superior bonding of the rock to the glass slide, thus virtually eliminating any failures due to parting of the section from the glass slide, and permit fast mounting, grinding, and finishing, thereby materially lessening the time required to prepare thin sections.

Jan 1, 1950

By Hsin Wei Wu

A real-time Diesel Particulate Matter (DPM) monitor has been developed on the basis of the successful National Institute of Occupational Health and Safety (NIOSH) designed Personal Dust Monitor (PDM) unit. The objectives of a recently completed Australian Coal Association Research Program (ACARP) study were to modify the PDM to measure the submicrometre fraction of the aerosol in a real-time monitoring underground instrument. Mine testing focused on use of the monitor in engineering evaluations to determine how conditions can be improved. Studies, including a selection during Longwall (LW) moves as described in this paper, demonstrated how DPM concentrations from vehicles fluctuate under varying ventilation and operational conditions. Correlation between the current SKC DPM measurement system and real-time DPM monitors were conducted and results from six mines show a correlation between elemental carbon (EC) and the new monitor DPM mass ranging from .51 to .81 with R2 >.90. These differences are suspected to be due to variations from mine to mine in aspects such as mine atmospheric contamination, vehicle fleet variations, fuel type, engine maintenance, engine combustion efficiency, engine behaviour or interference from other submicrometre aerosol. Real-time monitoring readily reflects the movement of individual diesel vehicles and allows pin-pointing of high exposure zones such as those encountered where various vehicles work in areas of constrained or difficult ventilation. DPM monitoring approaches that have been available for some time based on shift average monitoring do not readily allow successful engineering evaluation exercises to determine acceptability of pollution levels. Identification of high DPM concentration zones allows efficient modification of mine ventilation, operator positioning and other work practices t o reduce miners? exposures without waiting for laboratory analysis results.

Jan 1, 2010

By D. A. Larson

This is the second in a series of Bureau of Mines reports which de-scribe experiments designed to devise an efficient, economic mechanical fragmentation technique for hard rock. The previous study described the development of the ripper cutting technique to successfully cut hard rock with 3-to 6-in-wide drag cutters. This study was conducted to test the ripper cutting technique at full scale using 9-in-wide drag cutters. The experiments were conducted with a special test device that cut shallow, 6-by 6-ft openings in 9,200-lbf/in2 compressive-strength concrete blocks. The tests showed that ripper cutting can excavate large-scale openings of the type required by the mining industry at a production rate that outperforms the conventional drill-blast technique. Moreover, the system can produce openings of various sizes and shapes, is simple to oper-ate and maintain, and produces very little dust or noise during operation. The system appears to meet all of the criteria for a successful hard-rock mining machine.

Jan 1, 1987

By Manuel Gomez

The heat contents of thermally dried lignite, subbituminous B coal, and their corresponding low-temperature chars were determined at various temperatures below the highest temperature to which these materials had been exposed before testing. Similar studies were made on high-temperature char and coke, spent shale, and ash prepared from both coal and spent shale. Heat content of the carbonaceous materials tested correlated well with temperature. Heat con-tent results for spent shale compared well with the published results. Statistical analysis of experimental data together with published information showed moisture, volatile matter, carbon content, and temperature to be the principal variables influencing the specific heat of coal. The specific heat of devolatilized carbonaceous substances, char and coke, approached that of graphite as the carbonization temperature was increased. The elemental specific heats of coal constituents, estimated from the ultimate analysis and the specific heat of coal, compared favorably with published elemental specific heats.

Jan 1, 1965

By F. N. Kissell

The machine-mounted continuous respirable dust monitor (MMCRDM) is a fixed-location area sampling device developed for possible use at the working face of an underground coal mine. This device, based on proprietary technology known as the tapered element oscillating microbalance, has evolved over the past eight years through a cooperative effort of the former Bureau of Mines, MSHA, and the Rupprecht & Patashnick Company in Albany, NY. The capability to measure respirable coal mine dust levels on a continuous basis, rather than depending solely on periodic samples obtained from the traditional coal mine dust samplers, has been a goal in the mining industry for nearly two decades. Recently, an extensive series of laboratory and underground tests was conducted by NIOSH with the cooperation of MSHA and coal operators to test the performance of the MMCRDM In preliminary laboratory testing, the MMCRDM seemed to work well. However, in every underground test, when compared to reference samplers placed close to the inlet, the MMCRDM failed to meet the 25% accuracy criterion specified in the contract under which it was developed. Two reasons explain this failure: First, in most tests the bias (the relative discrepancy between the average MMCRDM concentration and the average reference sampler concentration) was too great. Second, the variability of the samplers used for reference comparison was too large. Finally, the underground testing of the MMCRDMs showed that they are quite unreliable at this stage of development. In the majority of mine tests, no more than 10 shifts of data were taken before the MMCRDM failed to function properly. Major breakdowns, requiring the return of the MMCRDM to the factory for repairs, occurred on average every 28 days. To be considered mine-worthy, MMCRDM reliability must be substantially improved. KEYWORDS Dust, coal dust, dust instrumentation, dust sampling, dust monitoring, black lung, pneumoconiosis

By D. Harrington

Although for many years considerable attention has been given to devising safe and efficient methods of using explosives, with some success, relatively little has been done to provide satisfactory storage facilities for them. This was known long before the present war began, but it was emphasized during the past 30 months? inspections of explosive magazines by employees of the Bureau of Mines in administration of the Federal Explosives Act of December 26, 1941. These inspections have revealed woeful in adequacy as well as definite hazards and the urgent need for obtaining better storage facilities either by remodeling old magazines or constructing ink new ones that would afford suitable protection for the contents against theft, fire, deterioration, and detonation. The purpose of this paper is to offer suggestions and to show by sketches and drawings some of the fundamental features of suitable magazines. Type of construction and available materials differ with different; localities, but the information herein contained can be applied to most magazines, whether already constructed or the construct: on of which is planned. It is hoped that this information will be helpful and will aid persons who are trying to provide suitable storage for explosives end detonators. It is also hoped that States and cities will be made aware of the unbelievable laxity practiced in storing explosives in the United States and will take some remedial action.

Jan 1, 1945

By D. E. Sullivan

The Bureau of Mines investigated the availability of potash from 68 mines and deposits in 12 market economy countries (MEC's) containing, at the demonstrated resource level, approximately 11.7 billion metric tons (mt) of potash in assay terms of contained K2O; K2O as used by industry as a standard of comparison for the different forms of potash. These resources include almost 190 million mt in the United States, 9.63 billion mt in Canada, approximately 430 million mt in Western Europe (France, Federal Republic of Germany, Italy, Spain, and the United Kingdom), 1.24 billion mt in the Middle East (Israel and Jordan) and over 220 million mt in other countries (Brazil, Chile, and the Congo). This analysis his determined that future production of potash in MEC?s will most likely continue to be from the large resources associated with producing operations in Canada. Based solely on the demonstrated resources included in this study, potash mining in the United States would decline while overseas production from MEC's can continue into the next century at near current production levels. However, timely development of new or inferred resources would offset any such decline. Producing mines in Canada have the resources to increase and maintain increased production well into the next century. For U.S. potash users, Canada is a long-term stable and secure source.

Jan 1, 1986

By Charles B. Carpenter

The New Hope field was selected for study by; Bureau of lanes engineers because many problems met by, the operators during development and operation were unique to petroleum-engineering experience. Solving these problems is believed to have doubled the ultimate recovery of oil from the field. Since the discovery well was 'completed, in April 1943, an oil-productive area of 4,950 acres- has been delineated by the drilling of 64 wells, four of which were dry holes. Four oil-bearing reservoirs - the Bacon oolitic limestone, and the Hill, Pittsburg) and Elledge sandstones, all, in the Trinity group of the Lower Cretaceous series-- have been penetrated at depths ranging from 7,300 to 8,100 feet. Three of these reservoirs were found to be closed-type or solution gas-drive reservoirs, and one - the Hill - was an open-type or water-drive reservoir. During the course of the study, the Tide Water Associated, Oil Co. and -Seaboard al Co. of Delaware made available to the writers all well records, electric logs; and coring, production,, and pressure data. The ,writers performed Certain field and laboratory- tests on cores of ,the reservoir racks and' samples -of the reservoir Oils. Analyses of cores from the four reservoirs showed average .porosities ranging from 10 to 18 percent, average permeabilities of 17 to 297 millidarcys, and -average 'connate water contents ranging from 25.4 to 30.6 percent. Subsurface and recombined samples of reservoir oils indicated that the oils in the Bacon Hill, and Pittsburg reservoirs contained ,206 to 422 cubic feet of gas in solution per barrel initially, and that the, reservoir oils were undersaturated with gas. No samples' of oil from the Elledge reservoir were analyzed, and because of meager data this reservoir was not studied in detail. 4 The presence of free 'gas' or a' gas cap, however, indicated that the oil in the Elledge reservoir was saturated with gas. The rapid decline in pressures in- the' four reservoirs during the 'first year of operation alarmed the operators and provoked them to investigate the reservoir conditions to determine the cause.

Jan 1, 1949

By R. F. Abernethy

Recent investigations in the United States and in other countries have produced considerable information on the nature and occurrence of minor elements in coal. The possibility of recovering certain elements, particularly germanium and uranium, from coal ash and other coal products has received considerable attention. Some flue dusts are potential sources of germanium, and certain lignite deposits are potential sources of uranium, but industrial recovery of these elements has been limited to small quantities for technical and economic reasons. Considering the large amount of coal mined annually, a small percentage of a rare element may have industrial significance if an economical method of recovery can be developed. In 1944 information on the occurrence of rare elements in coal was reviewed in Bureau of Mines Technical Paper 669 (46).3 This report is a revision of that paper with the view of summarizing published information available for United States coals, and pertinent information concerning coals of other countries. Selected references from the original paper are retained. New references do not include all preliminary reports when more permanent literature describing complete projects is available. Consequently, the list of references should not be considered complete.

Jan 1, 1963