Search Documents

By E. J. Gleim

During the past 10 years the Bureau of Mines has had a broad experience in the tasting and inspection of electric motors for gaol-cutting machines, cowl drills, storage-battery locomotives and other equipment Which is used in mines where explosive mixtures of methane and air may be encountered. From this experience the Bureau's engineers have reached the conclusion that the most satisfactory method of protecting a motor so as to prevent any sparks resulting from rough commutator, loose contacts or short-circuits in it, from igniting he surrounding atmosphere, is to totally inclose the motor with a substantial casing; having flanged joints. These joints should be metal-to-metal contact so that the shortest path from the interior to the exterior Of the casing is not less than one inch in length. On account of this experience with mining machinery, the Bureau has been asked whether an equal or loss degree of protection would be sufficient for motors for service in or about places such as refineries, gasoline filling stations, cleaning establishments and pumping stations, or in any place where there is liklihood of explosive mixtures of gasoline or naphtha vapors and air accumulating.

Jan 1, 1922

By Robert W. Freedman

In the Bureau of Mines study, a filter with a 20-by 20-inch-square cross section was inserted into the exhaust ducting of a 4-stroke-cycle, 90-hp diesel engine, and the efficiency of removal of total particulate was measured gravimetrically as a function of time. Removal efficiencies were close to 90 pct during the main portion of several extended runs employing several combinations of filter beds. Variations in engine load had little effect on collection efficiency. Particle size as measured by a Bureau-developed online instrument centered on 0.07 m based on number count. Removal efficiency increased rather sharply for both larger and smaller particles.

Jan 1, 1979

By Edwin B. Cook

Studies of flame and combustion phenomena at the Bureau of Mines have been facilitated by computer evaluation of the thermodynamic properties of gases formed by constant-pressure burning.4 5 This report is the sixth of a series6-10 presenting results of such calculations; it deals also with constant-volume deuterium-air flames.

Jan 1, 1961

By M. B. Cooke

An analytical method for the determination of the gum-forming material in gasoline has been developed by the Bureau of Mines, during a study nor in progress to determine the best rays for elimination of such constituents from gasoline. This method is similar in principle to that previously described by Smith end Cooke,2 which involved evaporation of e sample of gasoline in a small glass dish. The evaporation was started on an actively boiling steam bath and completed in an air oven at 105°C. In the improved method described below, the stem bath has been replaced by a steam heated oven in which an inert atmosphere is maintained. Air is excluded from the oven, consequently the precision of the determination is increased. Furthermore, evaporating dishes different from those previously described may be used.

Jan 1, 1925

By E. H. Boyle

The Bureau of Mines has evaluated the potential availability of silver from 436 mines and deposits in 41 market economy countries (MEC?s) comprising five major economic categories of deposits: predominantly silver deposits and predominantly zinc, lead, copper, and gold deposits. This study evaluated the long-term cost and availability of primary silver production from 53 producing and 13 nonproducing predominantly silver properties in 11 MEC's and estimated the total recoverable silver from 370 properties as a coproduct or byproduct of zinc, lead, copper, or gold production. This study resulted in estimates of a demonstrated resource of 5.99 billion tr oz of recoverable silver as of January 1984. Of this total, 23.5 pet is in the 66 mines and deposits classified as predominantly silver properties. The largest quantity of recoverable silver, 43.9 pct, lies in the 121 properties classified as predominantly zinc, with 26.5 pct in 120 properties classified as predominantly copper, 4.1 pet in 21 predominantly lead properties, and 2.0 pct in 108 predominantly gold properties. At current silver prices, the economics of silver production favor silver that is a byproduct or coproduct of zinc, lead, copper, or gold, and much of the silver production in the United States from the predominantly silver mines is at an economic disadvantage in comparison with silver production in other countries.

Jan 1, 1986

By W. R. Reed, G. J. Joy

The personal dust monitor (PDM) is a new coal mine respirable dust sampling instrument that has the ability to provide accurate end-of-shift and real-time respirable dust exposure data. A hypothetical cost comparison analysis of the PDM with the current MSHA-required coal mine dust personal sampling unit (CMDPSU) was conducted. Some simplifying assumptions were made to create hypothetical cases for analysis. This analysis was limited to respirable dust sampling of one designated operator (DO) and one designated area (DA) for one mechanized mining unit (MMU) which operated one shift per day. Only sampling intervals of the minimum sampling as required by federal regulations and continuous sampling were analyzed. This cost analysis from the company perspective is only one part of an overall cost/benefit analysis that should be conducted at a later date. In this analysis, company-associated costs were examined for both sampling systems. Results show that the PDM, while it has high initial costs of approximately $12,600, may be a cost-effective sampling system for measuring coal mine respirable dust. The estimated present worth cost of conducting the minimum required dust sampling over a five-year life ranges from $5,850 to $19,000 for the CMDPSU, with the higher present worth cost including costs of potential violations incurred. For the PDM, the comparable present worth cost is $14,900 to $19,300, with the lower present worth cost representing a lower capital cost of $8,150 per unit if more than 850 units are produced per year, while the higher present worth cost reflects the result with the higher $12,600 capital cost.

By K. K. Kelley

Synthetic fluorphlogopite mica (KMg3AlSi3010F2) is a relatively new product developed at the Norris (Tenn.) Station of the Bureau of Mines, Thermodynamic data have applications both in the production and use of this product, and the work described in this paper was undertaken to fill the need for such data. Measurements were made of the heat of formation at 298° K., the heat capacity between 50° and 298° K., the entropy at 298° K., and the heat-content and entropy increments between 298° K. and a maximum of 1,804° K. These basic data are combined to obtain heats and free energies of formation of the mica from the elements and from molecular constituents at temperatures ranging from 298° to 1,800° K. Minimum heat requirements to form melted mica from commonly used ingredients were calculated.

Jan 1, 1959

By H. W. Sheffer

Technical and economic aspects of community refuse disposal systems and their effects on the environment are identified and described. Seven landfills and two incineration systems, located throughout the United States, are reviewed.

Jan 1, 1971

By H. Netuka, J. V. Horak, A. W. Khair

"A general review of major problems concerning mathematical modelling of roof bolting problem is given. A mathematical model (MM) of interactive set Bolt - Resin - Rock and its discretization based on the Finite Element Method (FEM) is developed to calculate numerically course of displacement, stress and strain fields in this set. This new MM enables to get also course of the normal and tangential components of contact stress vector, normal displacement and then mutual tangential slip at the bolt - resin and resin - rock interfaces, respectively.Behavior of system on all interfaces is modelled in the MM as a ""unilateral contact"" governed by so called non-classical boundary condition of Signorini's type including Coulomb's law of friction between resin and rock, and ""a given friction"" law between bolt and resin (see Duvaut, Lions (1972) for mathematical formulation).Numerical example and some values of resulting stresses are shown and remarks on necessary and sufficient conditions for solvability of the problem are also given.IntroductionAs is well known roof bolting has become the primary support system in almost all underground coal mines. But the ""theoretical"" design criteria for roof bolt patterns are rather problematic because: "" ... real mechanisms by which the roof bolts reinforce the immediate roof of underground coal mine entry are still relatively unknown"", see Peng (1986).The aim of this contribution is to present brief description of fundamentals of mathematical theory (see Hlavacek et al., 1988) which could be, according to our opinion and knowledge, very helpful for numerical modelling of a such type of problems. For the sake of brevity we restrict ourselves here to just one of the simplest possible problem: analysis of the behavior of interactive set composed by only single full - length - grouted bolt, resin (or cement) and suitable part of domain of a ""immediate"" neighborhood of bolt which should represent physical action of real rock material."

Dec 1, 1995

By C. R. Hubbard

The Bureau of Mines investigated the mineral resources of the Upper Missouri River Basin as a part of a comprehensive water and related land resources study by six Bureaus of the Department of the Interior, coordinated by the Department?s Missouri River Basin Field Committee. The mineral resource study covers an area of about 18,000 square miles within the Great Plains physiographic province of central Montana. Exposed formations in the plains are chiefly flat-lying Cretaceous sediments. Plutonic rocks crop out in the central parts of the mountain uplifts, with steeply tilted Paleozoic sediments exposed around the margins. Oil and gas have been produced from several fields in the study area; total value exceeds $45 million. Coal-bearing formations of Upper Jurassic and Cretaceous age cover approximately 45 percent of the study area. Total production of coal since 1880 has been between 40 and 50 million tons, exceeding $75 million in value. Total metal production has been about $52.5 million. Industrial mineral production from 1925 through 1960, is valued at $24 million.

Jan 1, 1964

By C. R. Hubbard

The Bureau of Mines investigated the mineral resources of the Upper Missouri River Basin as a part of a comprehensive water and related land resources study by six Bureaus of the Department of the Interior, coordinated by the Department's Missouri River Basin Field Committee. The mineral resource study covers an area of about 18,000 square miles within the Great Plains physiographic province of central Montana. Exposed Formations in the plains are chiefly flat-lying Cretaceous sediments. Plutonic rocks crop out in the central parts of the mountain uplifts, with steeply tilted Paleozoic sediments exposed around the margins. Oil and gas have been produced from several fields in the study area; total value exceeds $45 million. Coal-bearing formations of Upper Jurassic and Cretaceous age cover approximately 45 percent of the study area. Total production of coal since 1880 has been between 40 and 50 million tons, exceeding $75 million in value. Total metal production has been about $52.5 million. Industrial mineral production from 1925 through 1960, is valued at $24 million.

Jan 1, 1964

By Van E. Shaw, D. J. Bauer

Conversion of euxenite concentrate to sulfates with sulfuric acid and solvent extraction of the yttrium- rare - earth mixture with EHPA were studied to determine extraction and separation characteristics . Digestion with 3.5 pounds of 96 percent sulfuric acid per pound of concentrate at 336 ° C for 4 hours resulted in an easily handled product with a yield in excess of 98 per- A thorium- free product was obtained by calcining the sulfated material for 3.5 hours at 650 ° C prior to leaching with water . Di ( 2 - ethylhexyl ) phosphoric acid solvent is an effective extractant with preference for cerium ( IV ) and heavy - group rare - earth elements including yttrium . Separation of complex rare - earth mixtures into light- and heavy - group fractions is feasible , and these fractions can be further processed to isolate ytterbium , neodymium , and dysprosium by changing processing conditions to obtain separation factors greater than two between these and adjacent elements .

Jan 1, 1965

By J. B. Zadra

After the discovery of the rare-earth mineral deposit in the Clark Mountain area near Mountain Pass, San Bernardino County, Calif., two samples wore obtained through the Mining Division of the Bureau of Mines for investigation of possible method of concentration. Three other samples were received later from different locations in the same area. The rare-earth mineral in this ore had been identified by E. T. Schonk as bastnaesite, a fluocarbonate of the rare-earth metals containing cerium, lanthanum, praseodymium, thorium, uranium, etc. Associated with the bastnaesite were barite, silica, and some calcite. The bastnaesite contained a small amount of iron as a coloration and some manganese. Twenty to fifty percent of the weight of the samples studied was bastnaesite, or ten to twenty-five percent total rare-earth oxides; about half was cerium oxide. Apparently, none of this mineral occurred in pure form. Even the highest-grade particles 'wore contaminated by fine, interlocked grains of barite, calcite, and silica; barite contamination predominated, and the barite was interlocked with varying amounts of bastnaesite. While the specific gravities of pure bastnaesite and barite (approximately 5.0 and 4.50 respectively) differ enough to allow separation by gravity, the interlocking of the minerals nullified this difference. Consequently, only a partial separation could be made by gravity concentration. The extremely fine grained texture of most of the ore prevented grinding to a size that would make concentration by flotation practicable; a partial separation of barite by this means was effected.

Jan 1, 1952

This paper has peen translated from the Russian by the United States Bureau of Mines and is issued as one of a series of circulars dealing with mining methods and costs in connection with a general study of this subject sponsored by the bureau. The paper presents some interesting features in connection with the methods employed in Russia and describes certain variations in standard methods which might conceivably be applied to a limited extent in this country.

Jan 1, 1930

By S. J. Pearce

The Bureau of Mines has prepared, as circumstances have dictated, a series of Schedules setting forth the minimum requirements that various types of equipment should meet to be considered safe and satisfactory for use in certain hazardous or unhealthful conditions. These Schedules cover a wide variety of devices ranging from explosives to electrically operated mine locomotives. This paper deals with those Bureau of Mines Schedules under which respiratory protective devices are tested and approved, and its purpose is to explain the function and operation of these Schedules. Provisions have been made for testing and approval of the following types of respiratory protective devices: Self-contained breathing apparatus,2/ supplied-air respirators,3/ gas masks,4/ dispersoid respirators,5/ and chemical cartridge respirators.6 These devices are tested at the Central Experiment Station of the Bureau of Mines in Pittsburgh, Pa. Self-contained breathing apparatus is tested by the Safety Branch, and the other types of respirators are tested by the Health Branch.

Jan 1, 1951

By M. K. Quinn, N. P. Reddy, A. W. Khair

"An analysis of coal fragmentation due to the action of a continuous miner is presented. Underground coal cutting by a drum-type continuous miner was simulated in the laboratory using a specially designed unique automated rotary coal cutting simulator (ARCCS). The rotary coal cutter provided the versatility of varying the operating and in-situ parameters to provide information on the effects of generating 37 pm (0.0015 in) particles. In these tests, coal blocks with an approximate dimension of 50.8 x 35.6x 20.32 cm (20x 15x 8 in) were first subjected to confining pressures equivalent to in-situ conditions. The blocks were then cut by the rotary cutting head of the ARCCS, thus simulating the action of the continuous miner in underground coal mining. During the tests under a particular set of in-situ and operating parameters a number of other parameters such as (1) penetration of bit into coal, (2) penetration resistance (thrust and cutting pressures), (3) rotating velocity of' cutting head, and (4) acoustic emission activity in the coal block were monitored. During the test, all the cut products were collected for size distribution analysis. After each cutting cycle the fractured surfaces were photographed and a velocity survey was conducted using a sonic technique. At the end of each experiment the cutting paths of the bits in coal were photographed using a camera attached to an optical microscope.The results led to a better understanding of the mechanisms of the fragmentation process during coal cutting and the effect of operating parameters, in-situ conditions and coal type on the size distribution of the cut product:"

Jan 1, 1989

By W. F. M. GOSS

The locomotives in service on the railroads of this country consume more than one-fifth of the total coal production of the United States. The amount is so large that any small saving that can be made effective in locomotive practice at once becomes an important factor in conserving the fuel supply of the nation. For this reason the United States Geological Survey gave attEmtion to the special problems of combustion in locomotive boilers. It approached this task from several different directions. The facts presented herewith constitute one series of results. In the fall of 1906 the locomotive-testing laboratory of Purdue University, at Lafayette, Ind., entered on a series of tests, one purpose of which was to determine in precise terms the degree of efficiency with which a modern high-class American locomotive utilizes the heat energy of the fuel supplied to it. The general interest in the subject, the elaborate plans which had been formulated for conducting the work, and the substantial character of the support which had been pledged to maintain it justified the Geological Survey in aiding the investigation. a The cooperation of the Survey consisted in detailing experts to assist the regular staff of the laboratory in the chemical and calorific work of the tests. These experts, working under the general supervision of the director of the Purdue laboratory, became responsible for the sampling of smoke-box gases, of the fuel used, of the cinders caught in the front end, of the sparks discharged by the stack, and of the refuse caught in the ash pan. The gas analyses were made by them at the university laboratory. The analyses of all solid samples and the calorific tests of the fuels were made at the government fuel-testing plant at St. Louis. The representatives of the Survey were not concerned with other phases of the work.

Jan 1, 1911

By H. L. Gilbert

Zircon sand may be reacted with sodium hydroxide at 600° C. to form sodium zirconate and sodium silicate. Sodium zirconate is water insoluble and so may be washed free of sodium silicate. The sodium zirconate may then be converted to zirconyl chloride by the action of hydrochloric acid and the zirconyl chloride crystals separated by cooling the solution. This approach produces zirconyl chloride of satisfactory purity with less cost than is involved in buying anhydrous zirconium chloride and converting it. A proposed design for a plant is given, INTRODUCTION This work was conducted by the Rare Metals Branch as a part of research on zirconium at the Bureau of Mines Northwest Electrodevelopment Laboratories, Albany, Oreg., under the guidance of S. M. Shelton, Regional Director. The work was supervised by W. W. Stephens, head of the Rare Metals Branch (now with Carborundum Metals Corp.).

Jan 1, 1954

By L. A. Neumeier

The Bureau of Mines investigated hot-rolling and forging characteristics of experimental ductile iron castings, both sand and permanent-mold, made with charges containing up to 70 pct foundry pig iron and 95 pct steelmaking pig iron. Between 1,550° and 1,950° F, most castings could be rolled to 90-pct reduction or forged to 70-pct reduction without serious cracking. Charge and composition have less bearing on workability than on subsequent properties. Permanent mold castings could be worked as readily as sand castings at 1,750° and 1,950° F. Plasticity improved with temperature. Small billets were also forged cold to 50-pct reduction without cracking. With equivalent nodularity, composition affects properties of wrought materials by altering matrix structure and strength. Properties vary with reduction and improve with increasing working temperature. Rolled material has high strength and anisotropy, and low ductility, particularly in the trans-verse direction. Annealing reduces strength and improves ductility, but anisotropy persists. At 70-pct reduction, impact resistance in the longitudinal direction is about twice that in the transverse. Annealing roughly doubles impact resistance. Deformation enhances damping capacity. The feasibility of die-forging and bar-rolling of ductile iron was evaluated in trial tests conducted under a Bureau contract. Although workability and ductility of ductile iron are inferior to those of steel, more advantage could be taken of ductile iron's plasticity to work rough shapes to final dimensions.

Jan 1, 1980

By F. S. Crawford

"After many years of safety activity in the United States in one form or another it becomes increasingly evident to those in contact with safety work that to achieve continuous good results in accident prevention there must be an aggressive organization behind the safety movement at each mine with fairly definite plan and policy. A study of the methods used by various companies and the results they have attained will be of value to the common cause of safety promotion.A study has been made of the safety records of the Menominee iron range in the Lake Superior district, and of data from the county mine inspector's report. Several companies on this iron range that have attained a certain measure of success in their work of accident prevention have given data, and a summary of their safety methods is presented.The Menominee iron range of Michigan lies in the southern portion of the upper peninsula of Michigan, bordering on Wisconsin. It consists of two main. divisions--the West Menominee Range, situated in Iron County in the vicinity of Iron River and Crystal Palls, and the East Menominee range situated in Dickinson County in the neighborhood or iron Mountain, Mich. The mines about Iron River and Crystal Falls are peculiarly subject to fires in a carbonaceous, sulphur-bearing black slate which appears in the footwall. This gives considerable trouble because fires in this material start from spontaneous heating. The methods of mining are top slicing and open stoping, working on benches along the sides of the stopes. The character of the ground varies from medium Soft ore to relatively hard ore which permits open stoping. Approximately one-third of the operating mines are equipped with a fan for main mechanical ventilation. The remainder are ventilated by natural draft. The East Menominee range is the older, top slicing having been used there for a number of years, and the timber mats have boon well developed. In common with all districts, some companies pay more attention to safety than others, although, those which do riot have the best records do pay some attention to safety.During the past three years the annual production per man employed has remained about constant, but in many mines a general decrease is shown in the accident record. The variation in the results attained can be ascribed mainly to the earnestness with which accident-prevention work is pursued, essentially regardless of the method of mining used. This is shown to be generally true, because the record indicates a steady decrease in one mine with an active safety department, while in adjoining mines with the same kind of ground and method of mining but where not such intensive attention has been paid to safety work, the accident record is high."

Oct 1, 1931