Search Documents

By Louis H. Berkelhamer

"INTRODUCTION In the present war, with increasing demands on foundrymen for speedy production of sound castings, the role of sand in foundries has paramount importance.Foundry sands include both molding sands and core sands. Molding sands are those used in making molds, whereas core sands include those used for ""cores"" that fill the parts of the mold intended to be openings or hollow spaces in the casting. Core sands are, as a general rule, relatively coarse-grained as compared to molding sands. Coarse-grained sands, however, are required in making molds for large castings.Owing to the intimate relationship between properties of the sand and casting defects, it is necessary (for most efficient foundry work) to keep a close check on the molding sands used and to properly select and prepare a sand for a specific job. A mold is essentially an unfired refractory composed to meet specific requirements as to strength, permeability, and resiliency. Good green strength is important in preparing and handling the mold. Low dry and hot strengths contribute to cutting and washing, whereas high strengths cause difficult shake-out, with subsequent loss of sand. When molten metal is poured into the mold: a dried skin is attained, and gases from moisture and combustibles are driven off. Excessive moisture necessary for the proper working of a sand, as well as poor venting due to low permeability, are factors responsible for producing such defects as blows and pinholing. The skin of the mold, upon contact with molten metal, first expands and later contracts; these conditions are favorable for producing scab defects. Contact with the molten metal sometimes causes the skin of the mold to sinter or fuse and may produce a sand burn on the casting. Then again, the mold may develop excessive hot strength rapidly, thereby causing a cracked casting. Experienced foundrymen can other such relationships, too numerous to be included here."

Sep 1, 1944

By R. A. Beall

Consumable-electrode arc melting is now accepted throughout the industry as the best method for producing ingots of zirconium, titanium, molybdenum, and their alloys. In addition, the technique is widely used in laboratories for fusing samples of such metals as hafnium, chromium, tantalum, columbium, and thorium. The production of consumable electrodes from these metals presents some rather difficult problems, the accepted industrial solution being the use of heavy powder-metallurgy-type presses. This paper summarizes information on fabrication of consumable electrodes by this and alternative means, such as sintering, nippling, and welding lightly pressed compacts of scrap metal. A possible saving of considerable capital investment is shown in the case of sintered compacts. The electrical circuit components of a pilot sintering unit are analyzed. INTRODUCTION The consumable-electrode arc-melting process has been accepted by most of the industry as the best method at present for producing high-quality pure or alloy in-got from sponge titanium or zirconium. This technique is not particularly new, having been patented by Von Bolton (l)3/ in 1909 for melting tantalum. However, it has been applied to industrial-scale operation only in the last few years. Among the important contributions to this technique are the work of Kroll (2) and Parke and Ham (3) and the work reported by the Office of Naval Research (4). The Bureau of Mines-has added considerably to the knowledge of this process (5-9).

Jan 1, 1956

By C. C. Shale

Current-voltage relationships for air at high temperature in negative corona are compared with relationships predicted by theory. Deviations are discussed. Eased on the latest theoretical concept of electron detachment from negative ions and recent findings in basic research on free electron gases, results of applied research show the existence of free electrons in air at high temperature and high field strength-to-pressure ratios.

Jan 1, 1967

By O. C. Blade

A comparison of certain properties of the commercial aviation gasolines produced in the United States during October 1949, 1950, and 1951 is presented in table 1, the 1951 data being average values from tables 3 through 6 of the present report. Trends in the average values of certain characteristics of these fuels may be seen in figures 1 through 4 which also indicate the minimum and maximum values. As may be observed, with the exception of changes in kinematic viscosities, the properties of commercial aviation gasolines have not varied greatly during recent years. A list of aviation-gasoline survey reports published by the Bureau of Mines is given on page 6. A summary of the average values of the properties on jet fuels is shown in table 2.

Jan 1, 1952

By R. W. Huber

Three arc-melted ingots, two of a titanium-7 percent manganese alloy and the third of unalloyed titanium, were forged and rolled into 3/4-inch plate; comparative data were obtained on these processes. The finished plate, part of which was used by the Naval Bureau of Ordnance, was tested for mechanical and other properties. These properties were correlated with sponge purity, forging technique, rolling temperature, and cooling rate from the rolling temperature. For the alloy material, transformation data were obtained, and their age-hardening characteristics were studied. The temperature-impact relationship was established for rolled sections from all three ingots. INTRODUCTION Arc-melted ingots of unalloyed titanium and a titanium-manganese alloy were fabricated into plate under closely controlled conditions by personnel of the Metals and Alloys Section, Physical Metallurgy Branch, Bureau of Mines, College Park, Md. This program was cosponsored by the Naval Bureau of Ordnance. Bureau of Mines interest lay in correlating the processing procedures with the mechanical properties of the finished plate.

Jan 1, 1955

By David A. Lipton

In the summer of 1985, at the request of the U.S. Forest Service, the U.5. Bureau of Mines examined the 109,000-acre West Big Hole study area to evaluate its identified mineral resources. The study area is in Beaverhead County, about 50 mi west of Dillon, MT. Four lode properties within or adjacent to the study area contain an estimated 452,000 tons of identified subeconomic gold-silver resources. Resources ranged from 900 to 302,000 tons, with estimated grades between 0.02 and 0.23 oz/ton gold and as much as 4.8 oz/ton silver. Gold, silver, and base-metal content in samples of poorly exposed mineralized structures indicate that exploration may identify resources on 18 additional lode properties within the study area and 5 properties adjacent to it.

Jan 1, 1988

By R. D. Ladoo

"At the beginning of 1920 a general feeling of optimism was noted in many talc-producing districts. The industry seems to have recovered from the temporary depression of the first half of 1919 and many mills are running at capacity production with their entire output for 1920 contracted for. The imports of talc for 1919 were only slightly larger than in 1918 by weight and probably no more by value. Thus foreign competition has not begun to be seriously felt. Several new companies in this country have been organized, some to operate new deposits and others to continue the work done by others.An interesting phase of the present situation is the possibility of increased use of talc in paint. There is a shortage of barium sulfate used as,paint filler. Since, for some uses, talc is considered second only to BaSo4 as a filler for paint, it is possible that part of the shortage could be relieved by an increased use of talc.A series of physical tests upon all pigment materials used in the manufacture of paints is being conducted for the Paint Manufacturers Association of the United States. It is important that all types of talc be represented in these tests. Producers of finely ground talc, 200 mesh and finer, are urged to submit samples of at least two pounds each of these grades that are available to paint makers with trade name and quality data, to the Institute of Industrial Research, 19th & B Streets, Washington, D. C., where the tests are being conducted.The Talc Products Company, Inc., Washington Building, Los Angeles, California, has recently been organized to develop a large body of talc one mile north of Riggs, San Bernardino County, California, This deposit contains a compact, white talc which can be sawed into crayons. The company's mill, at Los Angeles) is equipped with a unit of the Raymond system of grinding and air separation, and pencil sawing machines. It is reported that the pencils are being successfully used in Pacific Coast ship yards.The mining of talc where no mill is owned by the operator and the consequent sale of talc in its crude massive state has not proved profitable in a number of cases recently noted. Under exceptional circumstances, where mining costs are low and the product can be sold to a mill near the mine, the operation maybe profitable, but this condition is not common. One mine of this type has recently closed down, at least temporarily; but a second, more fortunately situated, in another district, is continuing operations, although plans are being made to erect a mill in the early spring. Most satisfactory results are ordi¬narily obtained where the mine and mill are owned by the same company.The sale of the Balmat mine of the International Pulp Company, near Gouverneur, N. Y., to J. H. McLear, Gouverneur, and H. G. McLear of New York, has been reported. It is stated that a large part of the property has been already leased to the Sylvia Lake Company, who will operate it. ""Cement, Hill, and Quarry""* states that ""the first mining done on this property was for silver and lead, but it developed into a good zinc producing property and later it was worked for its talc deposits. It has passed through several hands, the American Pulp Co., the Union Talc Co., and the International Pulp Co., all having had it in successive periods since 1891."""

Jan 1, 1920

By Philip W. Holland

The U.S. Bureau of Mines has designed and built an inexpensive, weatherproof, temperature-controlled cabinet to provide temporary housing for analytical instrumentation. The cabinet consists of an inverted Styrofoam ice chest, an electric fan for air circulation, and a proportional temperature controller equipped with a thermistor sensor and a light bulb as the heater. The cabinet provides a constant-temperature environment for a moisture analyzer and a strip chart recorder when outside temperatures range from -SO to 21° c.

Jan 1, 1993

By Maurice J. Peterson

THE VISUAL-ARC spectroscopic method of rapid qualitative analysis of complex inorganic compounds has been popularized in the past few years and is being employed by an increasing number of laboratories. The mineralogy and chemistry departments of several universities recently have added visual spectroscopy to their laboratory curricula. This revival of interest in a somewhat dormant analytical method has been stimulated through the publication of three papers 4 by members of the College Park staff of the Bureau of Mines. These virtually are the only recent sources of information on visual-arc spectroscopic analysis. They include data on the spectroscopic assembly, the analytical procedure, and the practical application of the method to determinative mineralogy and related fields. Requests for reprints of these papers continue to be received; at present only a limited number of copies are available for distribution. In order that these requests may be adequately answered, material from the three papers has been combined and, with some additional data, is presented in this bulletin. Numerous specific inquiries have been received regarding types of equipment available, problems in instrumentation, and information on the approximate sensitivity limits of the elements that can be detected by this method. Some of this material was not included in the original papers. Accordingly, the table of wavelengths has been revised to include the approximate visual-arc spectroscopic sensitivities, and a section on commercially available equipment has been added.

Jan 1, 1953

By F. M. Goodwin, John Campbell, W. P. Yant, G. W. Jones

"INTRODUCTION The cooperative investigation dealing with the general hazards of combustible gases and vapors in manholes owned by the Edison Electric Illuminating Co. and the New England Telephone and Telegraph Co. in Boston, Mass. and surrounding territory, was continued during 1934.The method and procedure of conducting the survey for 1934 were the same as those followed heretofore.ACKNOWLEDGMENTSThe cooperative investigation was arranged through the interest and effort of F. D. Comerford, president of the Edison Electric Illuminating Co. of Boston; E. M. Farnesworth, Jr., vice president and general manager of the Boston Consolidated Gas Co.; and A. C. Fieldner, chief engineer, Experiment Stations Division, U.S. Bureau of Mines. Thomas H. Haines, superintendent, Distribution Department, of the Edison Electric Illuminating Co., cooperated in furnishing both men and information for the work.The New England Telephone and Telegraph Co., through Chief Engineer G. K. Manson, R. F. Esterbrook, H. G. Crush, and A. J. McCarron, cooperated by assigning a telephone company employee for the test truck. The company has borne its proportionate share of the expense and has taken an active interest in the work during the year. The test crew was operated under the direct supervision of John Campbell, superintendent of the Special Service Department of the Edison Electric Illuminating Co., and 7. M. Goodwin, vice president of the Boston Consolidated Gas Co."

May 1, 1936

By S. A. Matthes

This Bureau of Mines report describes analysis of a copper slag for 13 elements from a single sample solution by flame atomic absorption spectroscopy. Samples are dissolved with 7 ml of an HC1-HF-HN03 (3:1.5:2) mixture in heated plastic pressure vessels. A 1.5-pct boric acid solution is added to dissolve precipitated fluorides and to reduce matrix effects that interfere with atomic absorption analysis. Preparation time is less than 1 hour per batch of 10 samples. Total analysis time is less than 6 person-hours for 130 determinations with an average relative standard deviation of 1.83 pct for the 13 elements. Simple acid standards were used for all determinations. Values obtained by this method are in excellent agreement with values obtained by slower, more costly procedures.

Jan 1, 1980

By R. J. Henry

This paper describing the mining practices at the Teck-Hughes mines at Kirkland Lake, Ontario, is one of a series being prepared by the United States Bureau of Mines on mining practices, methods, and costs in various mining districts. HISTORY Prospecting was begun in the neighborhood of Kirkland Lake in 1906, but staking did not take place until 1911. Gold-bearing veins were discovered by surface trenching in 1913 on the mining claims which now make up the Teck-Hughes Gold Mines (Ltd.). A small mill was erected in 1916 after the completion of some underground exploration. A transmission' line was built in 1917 to the camp to provide adequate power for a vigorous underground campaign. Also in 1917 the present management took control operations since 1916 have been continuous,' with a steady increase in production to date.

Jan 1, 1930

By B. E. Blair

"This report presents the physical properties and related geological and petrographic data of some 84 rock types from operating mines, quarries, or blasting research test sites. These fundamental rock data were collected as a quantitative approach to underground mining problems, blasting research, or other related studies; however, the data are equally applicable to any problem wherein rock characteristics are important factors. Stress-strain curves are given where available, and the standardized procedure for determining elastic constants from static tension tests is described. Computed (laboratory) and measured (field) free-medium velocities are compared in those instances where such data are available. A chart is given showing both the optimum and minimum number of test specimens for the various core sizes employed in the Bureau of Mines standardized physical-property tests. Rock-type, geographical, and geological indexes are included to aid the reader in locating physical-property data in this and previously published Bureau of Mines physical-property reports.INTROD'OCTI ONThis report presents the physical properties of 84 rock types tested from 16 different projects (sections 37-52). Two previous physical-property reports 2-3 / (hereinafter referred to as parts I and II) presented data on 160 rock types from 36 different projects (part I, sections 1-25 and part II, sections 26-36).The physical-property data were originally obtained to supplement structural mining problems, seismic studies, or related investigations; however, they should be equally applicable in all fields of studies where the strength, hardness, or other properties of rock are important factors. The properties, determined from laboratory tests performed on diamond-drill core, include the following:"

Jun 1, 1955

By K. K. Kershner

To meet an increasing demand for high-purity cobalt, the Bureau of Mines has conducted investigations for producing this metal. Cobalt having a purity of 99.95 percent or higher is needed to determine heats of formation, corrosion resistances, phase diagrams, and other basic properties of the element and its compounds. This grade of cobalt may be used for preparing radioactive metal. As a result of its investigations a detailed procedure, which is of practical significance to the production of high-purity cobalt, has been developed by the Bureau for purifying cobalt solutions and for electrolytic deposition of the metal. Cobalt metal, which had a purity of 99.99 percent with reference to metallic contaminations, was deposited electrolytically. Qualitative spectrographic analysis showed only traces of calcium, copper, iron, magnesium, nickel, and zinc.

Jan 1, 1956

By Paul G. Marinos, Vassilis Marinos, Evert Hoek

The Geological Strength Index (GSI) is a system of rock mass characterization that has been developed in engineering rock mechanics to meet the need for reliable input data related to rock mass properties required as input for numerical analysis or closed-form solutions for designing tunnels, slopes, or foundations in rocks. The geological character of the rock material, together with the visual assessment of the mass it forms, is used as a direct input for the selection of parameters for predicting rock mass strength and deformability. This approach enables a rock mass to be considered as a mechanical continuum without losing the influence that geology has on its mechanical properties. It also provides a field method for characterizing difficult-to-describe rock masses. Recommendations on the use of GSI are given and, in addition, cases where the GSI is not applicable are discussed.

Jan 5, 2007

By Charles Will Wright

The purpose of this paper is to present briefly certain preliminary results of the study of mining methods by the United States Bureau of Mines; to show the relative importance of each method in terms of tonnages mined and man-hours consumed; to give to the mining engineers and particularly to the young student of mining a better understanding of the principal mining methods; and to indicate changes now in progress and to present suggestions for improvements in the art of mining. Questions of mine development and details of underground practice such as drilling and blasting, loading, hauling, hoisting, ventilating, pay systems and mine management are omitted, as these have been or will be discussed in other bureau publications.

Jan 1, 1931

By Raymond W. Hiteshue

To aid in designing a continuous system for evaluating processes for converting coal to high-Btu gas] the Bureau of Mines determined the amenability of various coals and a char to hydrogasification at 800° C and 6,000 psig using a molybdenum catalyst. A lignite from Rockdale, Tex., an hvCb coal from Rock Springs, Wyo., a char from the low-temperature carbonization of the latter, an hvAb coal from Pittsburgh, Pa., and an anthracite from Luzerne County, Pa., were selected. Highest yields of gaseous hydrocarbons, 94 pet, based on maf feed, were produced from char, and lowest yields, 67 pct, were obtained from lignite. Hydrocarbon gases contained 82 to 92 pct methane, 8 to 15 pct ethane; and 1 to 3 pct propane.

Jan 1, 1962

By Scott Turner

Within recent years , people have begun to realize the importance and significance of the mining and allied industries . The leading part the engineer plays in civilization is becoming recognized . However , accurate quantitative knowledge of the industrial importance of mining is still seldom possessed except by those close to this business . It is true that there are a few who go to the extreme and represent the whole progress of civilization as a reflection of man's gradual mastery of mineral utilization , but on the whole , the magnitude of the industry is underestimated . The uncertainties of mining , as evidenced by the variable results of prospecting on surface or underground , in an unknown new field or from the bottom levels of a mature mine , the ins and outs of tonnages and metal contents , the possibility of a widespread or even a sudden change between cost and realization-price , add to its picturesqueness and make mining attractive to some . To many , the fact that results are generally more uncertain and less predictable than in other industries lends added charm . The following pages may serve to call attention briefly to the importance of mining relative to other industries in the United States , in Canada , and in the world . Ordinarily , the annual primary mineral production of the United States amounts to about 5 billion dollars . The average for the last five years has been a little over 5 billion dollars . Last year , sadly enough , it was less than 34 billions . Just now , we are on the decline , and have been for the past two years . In Canada , the 5-year average was about 268 million dollars . Last year it was 227 million . Due in part to gold output ( in 1930 , for the first time , Canada's gold production exceeded that of the United States ) , the Canadian average is holding up better than ours . It has been estimated that the average world mineral production over the past five years has amounted to about 12 billion dollars , while in 1931 it was less than 8 billions . The mineral industries are as indispensable for the conduct of modern society as are those of agriculture , but , in the United States at least , they receive far less recognition from the Government . With us , agriculture is fostered by a great department that is maintained by enormous appropriations , while the mineral industries get but little financial support . In the United States , in the calendar year 1930 , the value of production by these two industries were as follows : to 1 . Agriculture ( inclusive of forestry ) 9.9 billion dollars ; mining 4.8 billions ; ratio 2 Direct appropriations by our Federal Government were 109 million dollars to agriculture and 2.8 million to mining , a ratio of 39 to 1. Obviously this is out of balance to the extent of 19 to 1 in favor of agriculture .

Jun 1, 1932

By L. C. IlsLey

A list of permissible mine equipment, tested and approved p or to July 1, 1934, was published in Bureau of Mines Information Circular 6813/. The present list4/ includes virtually all the electric air compressors, coal drills, mining machines, loading machines, conveyors, mine pumps, room hoists, mine telephones, rock-dusting machines, switches, electric cap lamps, flame safety lanes, electric hand and trip lamps, electric flood lamps, methane detectors, blasting units, storage-battery locomotives, tandem locomotives, mower trucks, and concrete mixers tested and approved by the Bureau to January 1, 1937. The system under which these devices were tested permits the manufacturer, after his equipment has passed certain tests prescribed by the United States Bureau of Mines, to mark his equipment with a seal showing that it has been approved by the Bureau. These tests are designed to insure that equipments have the minimum requirements for safety in use. The only object of the bureau in making such tests and publishing lists of permissible equipment is to help decrease the hazards of mining.

Jan 1, 1937

By Jr. Karr

The Bureau of Mines studied the influence of carbonization method, temperature, and carrier gas on the composition of eight different low-temperature tars produced from a Colorado subbituminous coal. A fluidized bed was compared with an entrained bed, temperature was varied from 500° C to 650° C, and external heating using recycle gas as the carrier gas was compared with internal heating using oxygen-containing gas. The entrained bed yielded significantly more m-cresol and m-ethylphenol, indicating that thermodynamic equilibrium was more nearly approached in the system. Increasing the temperature greatly increased the yield of benzenes and naphthalenes, while paraffins, olefins, and total tar acids were reduced. Using oxygen in the carrier gas decreased the yield of low-boiling phenols and increased that of paraffins and olefins at 650° C.

Jan 1, 1966