Search Documents

By A. F. Colombo, D. W. Frommer

Bench- scale tests were made to determine the applicability of flotation as a means of upgrading finished and semifinished magnetic concentrates prepared from reductively roasted iron ores . Both anionic and cationic flotation methods were used to remove siliceous gangue from the magnetic concentrates and produce upgraded products . Seven magnetic concentrates , containing from 6.7 to 13.7 percent SiO2 , were improved by the flotation treatment , yielding final concentrates containing less than 6.0 percent Si02 . Cationic flotation methods were studied on four of the seven samples ; of this group only one sample yielded better results by cationic flotation than by the anionic method .

Jan 1, 1964

By G. E. Rennick

A siphon-type laboratory airlift well was designed and operated by the Bureau of Mines to study the concurrent flow of air and oil in small-diameter pipes. Glass flowstrings ranging from to 1 inch in diameter and from L4 to 64 feet in length were equipped with various-sized air-entry jets. Liquid holdup volumes were used to correlate vertical-flow data, and empirical equations for computing gas requirements were derived. The effect of flowstring length on flow efficiency, oil- and gas-production rates, and gas-oil ratios was relatively minor at all flowing pressures. Air-jet sizes and flowstring diameters, however, had a marked effect on flow efficiency and oil- and gas-production rates. The small air-jet sizes increased maximum flow efficiency and its associated flowing pressures but decreased oil- and gas-production rates. An increase in flowstring diameter increased maximum flow efficiency with its associated flowing pressure and also increased the production rates of oil and gas.

Jan 1, 1965

By F. N. Kissell, C. H. Elder, C. M. McCulloch

The applicability of the "direct method" for determining the methane content of virgin coalbeds was tested. Preliminary results indicate that the direct method, when applied to exploration cores, can be successfully used to estimate coalbed gas content and also approximately predict the total gas emission from a prospective mine located in the coalbed at the exploration site.

Jan 1, 1973

By D. A. Paice, A. B. Shimp

Illegitimate loads on a mine dc power distribution system can be detected by measuring a superimposed ac current. To implement such a scheme, a 10-volt, 3-kHz voltage is applied at each dc power substation. By this means, the mine dc power distribution network, consisting of a feeder and trolley wires with a grounded rail return, is caused to serve also as a 3-kHz ac distribution network.

Jan 1, 1975

By G. W. Jones

An important activity of the Bureau of Mines is the promotion of safety in mining and industry. As a part of this program, the Bureau determines the explosion hazards of combustible gases, vapors, and solids and investigates means of controlling and preventing explosions. The limits of inflammability (explosive limits) of combustibles are not only of theoretical but also of practical importance, because many industries at one time or another contend with explosive mixtures of combustible gases or vapors in their manufacturing processes. At present many new organic compounds are being manufactured, transported, and used in huge quantities which a few years a ago were only laboratory curiosities.

Jan 1, 1941

By J. J. Drost

This Bureau of Mines investigation studied the effect of thermal treatments upon concentratability of a western Mesabi Range nonmagnetic taconite ore and is a sequel to Bureau of Mines RI 7567. Magnetic tube tests were used to develop the data needed to calculate separation efficiency, the primary measure of concentratability. A horizontal tube furnace was employed to heat treat and reduce the hematitic ore samples. The two variables studied were roasting temperature and cooling method. The manner of cooling, either by slow cooling or quenching in water, produced no significant difference in concentratability. Roasting temperatures employed ranged from 500° to 1,000° C, and a temperature of 650° C effected the best concentratability. The temperature of 650° C correlated with the most effective roasting temperature for grindability.

Jan 1, 1973

By P. C. Good

This Bureau of Mines report describes the preparation of phosphoric acid directly from phosphate ore, without prior beneficiation, in a small-scale, continuous process research unit, as part of an effort to improve minerals and metals recovery from domestic resources while minimizing environmental effects. Three phosphate-matrix samples, ranging in grade from 18.2 pct P20S5to 11.9 pct P205, were dry-fed at a rate of 1.82 kg/hr (4 lb/hr) to a continuous-circuit, 12-liter, single-tank digester to yield phosphoric acid and byproduct gypsum filter cake. Comparison with earlier data shows that a significantly improved filtration rate was attained in a single-tank reactor compared with that attained in a five-tank reactor train processing the same ore. Iron and aluminum impurities in the product phosphoric acid averaged about 60 pct higher than amounts reported in commercially prepared, concentrate-derived acid. All gypsum filter cakes prepared had a firm, sandy texture, rendering them physically suitable for stacking or landfill use. Introduction of dry attritioning and air classification approximately doubled the attainable filtration rate when the dry-beneficiated product was digested. In air classification, there was a 12-to 14-pct P205 loss. Depending on the technique used and the matrix grade, overall P205 recovery ranged from about 72 to 89 pct.

Jan 1, 1979

By E. F. Ferrell

Electrowon molybdenum powders and a commercial hydrogen-reduced powder, all with different minor impurities, were investigated by the Bureau of Mines with respect to inherent properties, to fabrication techniques, and to proper-ties of the fabricated sheet. Compared with the commercial hydrogen-reduced powder, the electrowon powders had a larger particle size, a greater flow rate, a higher apparent density, and a lower oxygen content. Sheet materials prepared from the two types of powders showed similar mechanical properties, under the same conditions of heat treatments, except for low-temperature ductility. Yield strengths varied with carbon content, heat treatment, and test temperature.

Jan 1, 1970

By G. W. Jones

In the course of experiments on the stabilization of acetylene gas by addition of other gases, notably hydrocarbons such as methane, propane, and butane, it was observed that large quantities of carbon black are produced during the explosion of acetylene or mixtures of acetylene with the, above hydrocarbons, the added hydrocarbon being essentially decomposed into hydrogen and carbon. It is known that in the complete absence of air acetylene explodes upon application of an intense ignition source at pressure above 5.9 p.s.i. gage. The same is true of mixtures of hydrocarbons and acetylene. However, the pressures necessary for explosion are considerably higher in the case of these mixtures and depend on the amount of added hydrocarbon. The present report contains data on gaseous products and the physical characteristics of the carbon black formed by explosion at elevated pressures of various mixtures of acetylene and hydrocarbons as well as other gases, such as hydrogen, helium, nitrogen, and carbon dioxide.

Jan 1, 1950

By Frank B. Fulkerson

Three of the five primary aluminum producers in the Pacific Northwest have facilities in the region to make aluminum mill products. Only one of the three, however, produces a variety of shapes and forms. The principal reason for the lag in development of an aluminum mill products industry was found to be transportation cost. The long range outlook is for expansion, based mainly on growth of the western market for aluminum used in construction, containers and packaging, electrical applications, diesel trucks, mobile homes, and irregation pipe. Consumption of western aluminum mill products in 1985 is projected at 1.1 million tons, compared with estimated consumption of 250,000 tons in 1961.

Jan 1, 1965

By C. F. Winquist

The Bureau of Mines is engaged in research to evaluate the effects of cutter bit wear at coal mine faces. This paper addresses one element of conical bit wear, bit rotation. A discussion on mounting configura-tion and bit forces and their effects on rotation is presented. The effects on rotation and bit forces of bit attack angle, cutting depth, and skew are determined for two types of conical bits during linear cutting of sandstone-inclusive rock. The results indicate that a 10° negative skew angle and 35° attack angle produce the maximum rotation of 17.5° for each foot of cutting. Data on bit rotation and bit forces are presented in an appendix.

Jan 1, 1985

By John Durkin

Electromagnetic narrow-band signals were transmitted through the earth at 27 coal mines located throughout the United States. From those Bureau of Mines tests, apparent earth conductivity values were derived based upon a homogeneous half-space model of the earth. The derived conductivity values were found to be inversely proportional to the transmitted frequency and mine depth. A linear regression model relating the logarithm of the conductivity to the mine depth was formulated, and the results indicate that the mine depth can be an adequate predictor of the apparent earth conductivity above coal mines. Apparent earth conductivity was found to decrease with mine depth.

Jan 1, 1984

By Laurance L. Oden

The Bureau of Mines is developing melting data for binary combinations of the alkaline earth fluorides and yttria to facilitate the formulation of slag compositions. The present report deals with the SrF2-Y2O3 system for which liquidus and solidus temperatures and solid solubilities were determined. The information is presented as the phase diagram. The phase diagram was constructed from information obtained by ceramogra¬phy, X-ray diffraction, thermal analysis, and electron probe microanalysis of small specimens encapsulated in platinum-20 percent rhodium or molybdenum ampoules. The data indicate a simple eutectic system with limited terminal solid solubilities. The eutectic temperature is 1,457°±5° C, and the eutectic composition is 4±1 mole-pct Y203. Strontium fluoride containing up to 2 wt-pct 0 2 was studied to determine the effects of oxygen contamination. Oxygen levels in excess of 0.2 wt-pct resulted in eutectic formation between SrF2 and SrO. The eutectic composition is between 0.2 and 0.7 wt-pct 02, and the eutectic temperature is 1,447°±5° C. No intermediate oxyfluoride phases were detected.

Jan 1, 1974

By E. G. King

Many of the existing thermodynamic values for the titanium halides are estimates, including all the entropies and high-temperature heat contents of their crystalline and liquid phases. This report contains the results of low-temperature heat capacity measurents (which lead to entropy values at 298.15° K,) and high-temperature heat-content measurements of four halides - trichloride, tribromide, tetrabromide, and tetraiodide. The new data are combined with selected heat-of-formation values at 298.15° K. to obtain improved values of the heats and free energies of formation of these halides at high temperatures, thus supplementing the previous data of Kelley and Mah.5/ ACKNOWLEDGEMENTS This investigation was conducted under a cooperative arrangement between the Federal Bureau of Mines and the Department of the Navy, Office of Naval Research. The work was done by Bureau of Mines personnel using Bureau of Mines calorimetric equipment. The Office-of Naval Research supplied the supporting funds and arranged for procuring the samples of the titanium halides. The samples were prepared and analyzed by the Inorganic Chemistry Section, Division of Chemistry, National Bureau of Standards.

Jan 1, 1961

By J. A. Rowland

Magnesium alloys containing nickel, nickel and manganese, lithium, lithium and manganese, and lithium and aluminum were investigated. Melting, casting, and mechanical working techniques and the heat treatment of various compositions were studied. Amenability to cold and hot working was shown for many compositions. The magnesium-nickel and magnesium-nickel-manganese alloys failed to develop superior mechanical properties and were very low in resistance to corrosion. The magnesium-lithium series, although entirely plastic, had low strength properties. The addition of small amounts of aluminum to the Mg-Li base did not affect greatly either the ductility or the strength; further additions developed increased strength, but only at room temperature, and the alloys became brittle with age. Continued study, concentrating on the ductile lithium-rich beta phase as a base composition for ternary and quaternary systems, is recommended.

Jan 1, 1956

By J. G. Walters

This report presents the results of an investigation in Which the chloroform solubilities of coals and chars are related to rank, temperature of thermal treatment, time at a given temperature, vacuum thermal treatment, plasticity, oxidation, blending, and mass spectral analyses and molecular weights of the extracts. It was found that the quantity of chloroform extract obtained from chars can be altered by creating a vacuum above the charge during preparation of the char, increasing the time at temperatures within the plastic temperature range, and by utilizing different rates of heating to attain a given temperature. Relationships found between the chloroform solubilities of chars produced at temperatures within the plastic temperature range and the relative fluidities in this temperature range indicate that the chloroform-soluble portion of the char is a significant component of the plastic mass. Chloroform-extract yields from chars made from blends of coals cannot be calculated from chloroform-extract yields obtained from chars made from the component coals.

Jan 1, 1967

By Dennis A. Hansen

As part of a U.S. Bureau of Mines program to develop a more continuous titanium metal extraction process that uses domestic resources, a study was made to determine the extraction of titanium (Ti) and iron (Fe) from New York rock ilmenite using fluosilicic acid (H2SiF6). The effects of leach temperature, acid concentration, and particle size were investigated for the rate at which Ti and Fe are extracted from the ilmenite. Within the leach time studied, the extraction data fit a shrinking-core model; the rate-controlling step was diffusion of H2SiF6 through an ash layer resulting from a heterogeneous leaching reaction. The rate is linearly dependent on the H2SiF6 concentration and is inversely proportional to the square of the particle diameter. Using 2.6M H2SiF6 at 85°C, 49% of the Ti and 53% of the Fe in 44-to 74-µm New York rock ilmenite were extracted in 3 h.

Jan 1, 2010

By Alfred L. Ransome

The plan to develop a standard system of names and definitions of regions and districts in Alaska was borne of the need for a tool to use in statistical and economic studies of the mineral industry of the Territory. The purpose of this report is to present to the mineral industry, and to those individuals interested in the mineral or allied industries in Alaska, the system used by the Bureau of Mines in connection with its legal function of collecting and disseminating mineral statistics. It is hoped that the specific descriptions given will result in a more complete understanding of what is meant by the regional and district names that appear in publications of the Bureau of Mines relative to the mineral industry of the Territory. Problem of Standardization of Names and Definitions The question might be asked, does the naming and defining of regions and districts in Alaska present a problem relative to the establishment of a standard? Is it necessary to establish a standard?

Jan 1, 1954

By J. V. Batty

The Bureau of Mines devised techniques involving the use of beta-and gamma-ray-emitting radioisotopes and successfully adapted these techniques to the density of mineralized flotation froths) the rate of flow of finely ground ore pulps) and the residence time of pulps in processing circuits. Specifically, the water and mineral loads of flotation froths were continuously measured by determining the proportion of a constant-strength beam of beta rays that was absorbed by the froth column. Continuous measurement of the rate of flow of an ore pulp was accomplished by measuring the changing width of a free-falling stream of the pulp with a collimated beam of beta rays. The residence time of solids in conditioning and resin-in-pulp circuits was accurately measured by following the progress through these circuits of a portion of the pulp that had been tagged with the gamma-emitting Ag110 radioisotope.

Jan 1, 1966

By S. C. Schaefer

Thermodynamic properties of indium oxide (In203) have been studied with a high-temperature galvanic cell employing stabilized zirconia electrolytes. In the temperature range 790° to 1,230° K the free-energy change for the cell reaction 21n(1) + 3Cu20(c) = In203(c) + 6Cu(c) together with the standard free energy of formation of cuprous oxide gives the standard free energy of formation of indium oxide from the elements as ?Gf° = -218.78 + 75.34 X 10-3T ±0.7 kcal/mole. A third-law analysis yields the standard enthalpy of formation: ?Hf°298.15 = -221.5 kcal/mole.

Jan 1, 1971