Search Documents

By C. Q. Cupps, R. F. Zaffarano, J. Fry

Reservoir oil analyses from seven wells in the Greater Clareton area have been included in a study of the original characteristics of oil in the Newcastle sandstone reservoir . These data correlated with areal location of the wells show an increase of saturation pressure in a general north - south or downdip direction . The increase amounts to about 500 psi in more than 17 miles , which corresponds to a depth increase of about 1,600 feet . To facilitate application of the data to engineering analyses , average characteristics are given for arbitrary north and south divisions of the 22 - mile - long producing area . The downdip increase of saturation pressure is taken as evidence of updip diffusion of solution gas from a somewhat higher concentration at the bottom of the reservoir . This effect is opposite to that previously observed in two prominent high- relief reservoirs in the Rocky Mountain area . The increasingly greater saturation pressures southward or downdip in the Greater Clareton area suggest a continuing migration of fluids into the structure .

Jan 1, 1964

By W. E. Miller, Kennedy. R. E., G. W. Jones

"INTRODUCTION Ethyl mercaptan (CH3,CH2SH), a combustible organic liquid of the thioalcohol type, is employed at an odorant in many types of fuel gases and dangerous atmospheres, which in themselves are devoid of characteristic odors, to give warring against leakage of such gases or atmospheres into places where they might constitute health or explosion hazards.Ethyl mercaptan has a penetrating disagreeable odor resembling that of onions, garlic, hydrogen sulfide, or rotting cabbage, that exceedingly low concentrations of it can be detected. The of odorants as a beans of detecting leakage of gases and atmospheres has been investigated extensively by chemists and engineers of the Bureau of Mines, and numerous reports as to its value have been published."

Jun 1, 1942

By A. R. Taylor Jr.

The heat capacities of a-quartz form beryllium fluoride were measured at approximately 3° intervals from 8° to 300° K., using an adiabatic calorimeter. At 298.15° K the heat capacity and entropy were 12.39 cal/deg mole and 12.75 ±0.04 eu respectively. Enthalpy measurements were made with an ice calorimeter at approximately 30° intervals on the quartz and glassy forms of beryllium fluoride between 300° and 1,200° K. A melting point of 825° K and an 0,-8 type transition at 500° K with a heat effect of 75 ca1/mole were deter-mined from the enthalpy data for the quartz-type sample. Beryllium fluoride glass crystallized spontaneously into the quartz modification at 500° K. The heat of the reaction BeF2 (a-quartz) .... BeF2 (glass) was found to be 1,125 ±16 cal/mole at 298° K by solution calorimetry. This value, when corrected to 273° K, was used to correct for the heat absorbed by the formation of glassy BeF2 when the sample was dropped into the ice calorimeter from temperatures above the melting point. Using corrected enthalpy measurements, the heat of fusion was determined to be 1.13 kcal/mole at 825° K.

Jan 1, 1965

By R. O. Dannenberg

The Bureau of Mines investigations described in this report were undertaken to devise a process to economically recover precious metals and copper from low-grade, complex electronic scrap generated in large quantities by military and civilian electronic operations. Leaching with various media is applicable to certain selected items of electronic scrap but cannot be practically applied to complex mixtures of scrap. A process comprising incineration, caustic leaching to remove aluminum, smelting with a siliceous slag, and electrolysis recovered 99.9-percent-pure copper metal and anode slimes assaying more than 7,000 ounces per ton of combined precious metals. Silver, gold, and copper recoveries were 93, 95, and 87 percent, respectively. Cost analysis indicated that an alternative process using direct smelting of the scrap to make assayable products for sale to a custom smelter would provide better overall financial returns.

Jan 1, 1972

By J. T. McCartney

"INTRODUCTION The surface areas of the finest fractions of a pulverized material are disproportionately larger than their weights. For instance, Pesrott and Kinney 3/ showed that, in a sample of minus 200-mesh coal, particles that are about 2 microns in diameter represent 15 percent of the entire surface area but only 1.5 percent of the total weight. Because the sur- face area is the dominating factor in the behavior of finely divided materials in many practical processes, the role of the finest particles is of great importance. The oxidation and combustion of pulverized coal, both in the dry form and in suspension in oils, and the hydrogenation to fluid hydrocarbons of mixtures of pulverized coal and heavy oil are reactions in which the surface area of the coal particles has considerable influence. This investigation of the size distribution of fine coal particles was conducted with the hope that such processes would thereby be better understood. The results should also be of value in the study of the crushing and fracture of coal."

Sep 1, 1945

By F. R. Lee

[WHEN the Bureau of Mines was established in July 1910, one of the problems immediately attacked by the new organization was the development of standard, for the design and testing of electrical equipment that could be used without fear of initiating fires and explosions in underground coal mules. Research and investigation by Bureau personnel, supplemented by the published results of similar work by European mining authorities, led to the establishment of standards or "schedules." which guide manufacturers in the design of many types of electrically operated machines and devices used in. underground coal Mining. By issuing these standards, Bureau personnel establish the requirements to be met by such equipment before it tan be approved by the Bureau of Mines as permissible for use in gassy coal mines. Every 2 years the Bureau of Mines publishes a list of equipment that leas been accepted as approved or permissible during the preceding 2 calendar years. This is done to inform the mining industry of the availability of the latest equipment for safe use underground.]

Jan 1, 1964

By H. A. Watson

The introduction and use of synthetic materials in various applications may lead to potential hazards from toxic, gaseous, decomposition products if these materials are subjected to conditions abnormal to their intended use, such as high temperatures or burning from accidental causes. This report covers an investigation of such possible hazards from toxic gases produced by the burning or thermal decomposition of some low-density, expanded, synthetic materials, three of which consisted of polyvinylchloride and one of acrylonitrile. In the production of certain expanded plastic materials, Chemical blowing agents frequently are used to produce a cellular structure. One of these blowing or foaming agents contains azo-bis-isobutyronitrile, which is designated in this report as PN. Information indicates that a product of decomposition of this blowing agent, formed in the blowing operation, is tetra-methyl-succino-nitrile, designated as TSN, Which is significantly toxic. Decomposition of the blowing agent, with release of its azo nitrogen, is represented by the following reaction:

Jan 1, 1951

By A. S. Swanson

In view of the necessity or increasing production of metallurgical fluorspar to satisfy wartime demands, 0, M. Bishop, former district engineer of the Bureau of Mines, L. W. Carrier and. J. S. Williams, senior geologist of the Federal Geological Survey, and E. H. Dawson, mining engineer of the War Production Board made a joint survey of the Illinois-Kentucky fluorite district in July 1942 to determine what steps should be taken to increase production. As part of their recommendations, a program for exploring the idle Klondike mine in Livingston County, Ky., was outlined. All the ore produced at the Klondike mine was mined above the 325-foot level, where some tonnage remains. Factors that influenced selection of the Klondike mine for exploration were favorable geological conditions, the state of mine development and the availability of pumping equipment and some usable mine and mill equipment. In December 1942, the Metals Reserve Co. leased the Klondike mine from the Salem Fluorspar Co.

Jan 1, 1949

Workers at Anaconda Aluminum Company's primary aluminum smelter at Sebree, Ky., were back on the job December 1, after agreeing to a new 3-year contract. The old contract had expired November 15. On December 20, the Aluminum Company of America reportedly shut down a 42,000-ton-per-year potline at its Wenatchee, Wash., primary aluminum smelter and half of a 23,000-ton-per-year potline at its Vancouver, Wash., smelter as a result of a power cutback by the Bonneville Power Administration. A1 so in December, Kaiser Aluminum & Chemical Corp. reduced overall power at its Mead and Tacoma, Mash,, smelters and shut down one of eight 27,500-ton-per-year potlines at Mead. Reported shutdowns for the firms since September have amounted to 76,000 tons for Alcoa and 50,000 tons for Kaiser. Alcan Aluminum Ltd. announced plans to double the generating capacity at its Kemano hydroelectric power plant in British Columbia to 1,916 megawatts. The additional power would be equal to that required of a primary aluminum smelter with an annual capacity of 567,000 tons.

Jan 1, 1980

By D. E. Wolfson

As a part of its overall program of coal carbonization, the Bureau of Mines is studying the coking properties of coals that may be used for metallurgical purposes. The objectives of this study were given in detail in a previous report.2/ The inherent suitability of coal for metallurgical use depends primarily on (1) chemical composition, (2) preparation characteristics, and (3) carbonization behavior. The first two factors, as well as the available reserves, are considered in selecting coals for carbonization tests.

Jan 1, 1957

By William W. Elmer

This paper, describing the mining method at the Black Butte quicksilver mine, is one of a series of papers being prepared by the U. S. Bureau of Mines on mining practices, methods, and costs in the various districts of the United States. It is presented to show the mining practice and costs in the successful treatment of low-grade quicksilver deposits. The operation discussed is an excellent example of w1-pat can be done in working a limited tonnage of low-grade ore under sound management. The Black Butte mine is situated at Black Butte, Lane County, in the southern part of the State of Oregon, 17-1/2 miles from Cottage Grove -- a station on the Siskiyou branch of the Southern Pacific Co. The Black Butte mining district lies in the foothills of the Calapooia Mountain Range, which connects with the Cascade Range on the east and with the Coast Range on the west. The elevation at '.lie reduction plant is 1,000 feet above sea level. The apex of Black Butte Mountain, or which the mine is situated, has an elevation of 2,700 feet. The district possesses exceptional natural facilities infrequently met with elsewhere for the mining and reduction of cinnabar ores. Several factors which contribute to the unusually low mining costs are:

Jan 1, 1930

By V. B. Dale

This paper is one of a series covering the mineral resources of the Nation. It briefly describes most of the known tungsten deposits of New Mexico. Most of the descriptions are from field examinations by the senior author. Reported tungsten occurrences that were not visited are listed below: Colfax County: Occurrences of ferberite in thin veins in Willow Creek near Elizabethtown.4/ Dona Ana County: Small, low-grade occurrences of scheelite near the summit of the Organ Mountains about 15 miles east of Las Cruces. Hidalgo County: Scheelite reported in the Daisy mine 7 miles southeast of Hachita. Ores are carbonates containing copper, gold, silver, and bismuth.5/

Jan 1, 1959

By R. D. Groves

Laboratory research has demonstrated that high - grade copper powders can be produced under controlled conditions from cement copper products . The technique should enable small producers to prepare a directly marketable product by means other than smelting and electrolytic purification . A continuous drum- type precipitator was the preferred unit for producing fine - sized particles of cement copper that were further processed by chemical digestion in a copper sulfate solution , by reduction and sintering in a hydrogen atmosphere , and by grinding to a powder . The effects of variables related to all stages of the process were investigated . Treatment of leach solutions from three different sources resulted in copper powders containing 99.2 to 99.8 pct Cu , apparent densities of 1.97 to 2.25 grams per cu cm , good powder flow rates , and a size distribution of 54.9 to 60.1 pct minus 325 - mesh material .

Jan 1, 1964

By Murray Greyson

A number of tests were made with various methanation catalysts in fixed-bed, conventional fluidized-bed, and multiple-feed, fluidized-bed equipment to develop catalysts and processes for methanation of synthesis gas. The results show: 1. Methanation reactions may be carried out in 1-inch, bench-scale equipment at high synthesis-gas throughputs with good temperature control of the reactions if a multiple-feed type of fluidized-bed design is used. 2. Nickel is superior to iron as a catalyst for the methanation of synthesis gas, unless the process is considered in terms of a combined operation that produces both gaseous and liquid products. 3. Techniques of catalyst preparation determine, to a large extent, the process life of nickel catalysts, and these techniques must be thoroughly investigated before any conclusions can be reached. 4. Enough data are available to indicate that the sulfur concentrations in synthesis gas that is used for methanation are extremely critical, and maximum process limits should be carefully evaluated.

Jan 1, 1955

By Philip C. Tully

These modifications to the Redlich-Kwong equations for pure hydrogen and neon were developed after an unsuccessful attempt to generalize a modification technique previously developed for helium. New coefficients of the B terms were developed by minimizing the residuals. No changes were made in the coefficients of the A terms. For normal hydrogen, B was changed to [0.08063Tc PcT] for temperatures from 980 to 423° K and pressures up to 1,050 atm. The average deviation in Z was 0.36 percent with maximum deviations less than 1 percent for all but a few low-temperature points. For neon, B was changed to [PCT 0.1025T], for temperatures from 120° to 973° K and pressures up to 1,500 atm. The average deviation in Z was 0.34 percent with maximum deviations less than 1 percent for all but a few high-pressure and low-temperature points. Efforts to attain a lower temperature range to comparable accuracy with this type of modification were unsuccessful. In the range of applicability, these equations should be used with caution when calculating derived thermodynamic functions, such as the isobaric specific heat.

Jan 1, 1968

By Philip C. Good

Unweathered low-grade calcareous phosphate rock of about 20 percent P205 grade was beneficiated by a procedure in which contained carbonates were decomposed by calcination at about 1,000° C. On quenching the hot calcined rock in water, major impurities passed into a slime phase which was mechanically separated from a coarser concentrate fraction. Phosphate rock of two major types was beneficiated in batch-scale studies yielding concentrates containing 31.3 to 38.5 percent P205 at recoveries ranging from 54.8 to 86.0 percent. The samples were from two major deposits in India. Processing information gained was utilized in extending the work to a continuous-flow system, processing phosphate rock at rates up to 157 kilograms per hour. Superphosphate exceeding 16 percent water-soluble P205 was prepared from concentrate derived from continuous-flow processing.

Jan 1, 1976

By Fred N. Kissell

In This Chapter [The explosibility of methane gas mixtures Effect of pressure and temperature on explosibility Less common sources of methane ignitions The amount of methane stored in coal Forecasting the methane emission rate Layering of methane at the mine roof When the recirculation of mine air is hazardous The importance of higher air velocity in preventing methane explosions and Mine explosions, barometric pressure, and the seasonal trend in explosions] Dealing with methane in mines and tunnels requires knowledge of the circumstances under which dangerous accumulations of methane are likely to occur. This knowledge involves the properties of the gas itself, an awareness of where these accumulations are likely to occur, and facts on how methane mixes safely into the mine air. The other chapters in this handbook address the handling of methane under a variety of specific circumstances, such as at continuous miner faces or coal storage silos. This chapter addresses some broad concepts that serve as a foundation for the suggestions provided in other chapters. THE EXPLOSIBILITY OF METHANE GAS MIXTURES Methane entering a mine or tunnel often enters as a localized source at high concentration. Figure 1–1 depicts a cloud of methane being diluted into a moving air stream. In this illustration, methane enters the mine from a crack in the roof. As the methane emerges from the crack, it progressively mixes with the ventilation air and is diluted. In the event that this progressive dilution reduces the concentration from 100% to 1%,2 as shown in Figure 1–1, the methane passes through a concentration range of 15% to 5%, known as the explosive range. In the explosive range, the mixture may be ignited. Above 15%, called the upper explosive limit (UEL), methane-air mixtures are not explosive, but will become explosive when mixed with more air.

Jan 6, 2006

By Jr. Sillers

This is the third report of investigations dealing with the application of electrolytic manganese to steel-foundry practice and the seventh in a series of reports dealing with tests to establish the technological acceptability of electrolytic manganese in the iron and steel industries. The work was carried out by Metallurgical Division of the Bureau of Mines as part of an extensive program for the development and utilization of domestic ores. The electrolytic manganese used in the tests was produced by the Bureau at its Boulder, City, Nev., pilot plant by the process developed by the Bureau of Mines.

Jan 1, 1949

By T. L. Marchewka

As part of its program to conserve the Nation's natural resources by developing improved performance materials, the Bureau of Mines, U.S. Department of the Interior, in cooperation with the U.S. Department of Energy, has conducted an investigation of materials of construction able to withstand the high temperature and hostile environments encountered in coal gasification units. Refractory pipe liners are required when extremely hot gases or abrasive solids are transported between processing units in the gasification plants. One promising technique for producing refractory pipe (or refractory pipe liners) is centrifugal casting. For this study, the effect of processing variables such as workability, additives, reinforcement and spinning time, and centrifugal force were evaluated using four commercial refractory concretes. In addition, data on characteristics such as strength, density, abrasion, and spalling resistance of 5-inch-diam refractory pipe were developed. Techniques for forming large-diameter (19-inch) refractory pipe also were evaluated. The test results indicated that all four refractory concretes could be made into strong, homogeneous pipe, but that optimum casting parameters had to be determined for each specific composition. The investigation revealed that the major controlling factor in the production of the centrifugally cast pipe was the workability of the refractory concrete.

Jan 1, 1979

By K. E. Soroka

More than 500 fires are now burning in abandoned coal waste banks and coal deposits in the United States. Once established, such fires can burn for decades, and extinguishing them by conventional methods such as surface sealing to exclude air, excavation to remove fuel, or flushing to cool the fire zone is usually difficult and always expensive. Burnout Control, a technique developed by the Bureau of Mines for the control of abandoned coal fires, involves the accelerated combustion of coal in place with total management of the heat and fumes produced. A burning waste bank or mine is placed under negative pressure relative to the atmosphere, and heat and combustion products are drawn from the combustion zone through an exhaust ventilation system. Heat produced appears as sensible heat in the exhaust, at temperatures as high as 1,0000 C (1,832° F), and could be recovered for the production of steam, hot water, process heat, or electricity. The Bureau's first held field demonstration of Burnout Control was at Calamity Hollow in Allegheny County, PA (near Pittsburgh). Calamity Hollow was the site of an underground mine in the 1900's and was surface mined in the 1940's. In the winter of 1961-62, a fire of undetermined origin was discovered in the exposed coal. In 1963, the Bureau constructed a trench barrier around the fire and a surface seal over the affected area. The fire was isolated but not completely extinguished. In 1979, when the Bureau began work on the Calamity Hollow Mine Fire Project to demonstrate controlled burnout, the fire was still smoldering on the hot side of the trench barrier. The project, which was begun in December 1979 and ended in July 1982, consisted of the design, construction, operation, and subsequent dismantling of a Burnout Control ventilation system. This report is the fifth in a five-part series that describes the Calamity Hollow Mine Fire Project. The first report, part 1, describes the design and construction of the field installation. Part 2 will present the results of a continuous 4-month burnout operation. (Because part 2 involves the analysis of a substantial body of data, it will not be published until after publication of parts 1, 3, 4, and 5.) Part 3 describes the instrumentation used to control and monitor the progress of the burnout operation. Parts 4 and 5 deal with the closeout phase of the field demonstration. Part 4 describes the procedure used to quench the fire, and this part (part 5) describes the final excavation and backfilling of the heated zones. The reports in this series document the Calamity Hollow controlled burnout demonstration which showed that (1) controlled in situ combustion is a feasible method for controlling underground fires in abandoned mines, (2) the resultant thermal exhaust output is sufficient for energy utilization, and (3) water injection-fume exhaustion is a potentially effective method for cooling large underground fire zones. Further investigations of both Burnout Control and the water-injection-fume exhaustion quenching procedure are planned.

Jan 1, 1986