Search Documents

By R. V. Higgins

This report presents the results of a study of water injection in the HX sub-pool fault block V-B, in the Upper Terminal zone, Wilmington field, California, and is based on data obtained to May 1957. An earlier report3/ describes the results of gas injection in part of the field. The principal purpose of the pilot flood was to determine whether a sand having a permeability of 1,200 millidarcys and containing oil having a viscosity of 17 centipoises could be waterflooded effectively. The results of a preliminary study by engineers of the Long Beach Harbor Department of oil recoveries from areas where encroaching edgewater was active and the results of an independent study by a consultant retained by the Long Beach Harbor Department were favorable to a trial waterflood. After these preliminary studies, a detailed petroleum-engineering exam-ination was made of the technical details. As a result, a peripheral flood was started in June 1953. The peripheral flood was deemed desirable because the producing wells are bottomed a short distance from the edgewater. The HX subpool was selected for the pilot test because it is an isolated section of the Upper Terminal zone and is separated from the adjoining pools by faults on the east and west and by edgewater on the north, south, and west. Several petroleum-engineering methods were applied to evaluate the performance of the waterflood, and all showed that injecting water stimulated oil production.

Jan 1, 1958

By Jr. Herty

Manufacturers and consumers of steel have come to realize during the past few years that cleanliness is of great importance in steels which must meet rigid specifications for various physical properties. Of equal importance is the consistent production of steel which is uniform in these properties. For maximum utility, steels should be uniform not only from heat to heat, but also from ingot to ingot and within each ingot. In the manufacture of killed steels such as the higher carbon forging grades, uniformity as indicated by the usual chemical analysis is easy to obtain, provided that a normal top discard is taken, as is always the case in steels poured with hot-top practice. No such uniformity, however, holds true for the nonmetallic matter, which consists for the most part of the products of deoxidation of the steel. For a large tonnage of steels which go into articles manufactured by deep-drawing processes, killed steel has never been successfully applied because with the present deoxidation practice, low-carbon killed steel is almost invariably extremely dirty. To obtain the desired qualities for deep drawing, the steel is rimmed, - that is to say, deoxidized with manganese and perhaps a small amount of aluminum, - the resultant product being of high purity in the skin of the ingot, but very badly segregated at the center of the ingot, particularly in the upper-central section. This segregation necessitates a very heavy top discard, and one of the major segregates is carbon which renders the steel too hard to draw properly. If clean, low-carbon killed steel could be made successfully, much better ingot yields would be obtained than by the present rimming steel practice. Furthermore, banded structures and outside and inside seams, which are undoubtedly due in a large measure to blowholes in the ingot, are defects which are very difficult to control in rimmed steel.

Jan 1, 1931

By Thomas Fraser, J. D. Davis

"INTRODUCTION Preliminary tests of the Oyon coal constituted part of a wartime exploratory and development program in which many agencies participated. The general objective was to find new and adequate source of fuel and other raw materials for greatly expanded industry.The Oyon coal field, known for at least a hundred years to the mining people of Peru, offers a possible source of high-grade process fuel for the growing metallurgical industries of South America and the Pacific coast. Santolalla 4/ reports that low-volatile coal from this region was used in local smelting operations as early as 1850. It has been mined in very small quanti¬ties for many years and used in neighboring mining camps and villages. Small quantities are regularly used at Oroya for the manufacture of carbide, and in recent years small-scale coking operations in specially designed ovens in the region have demonstrated that these coals will make dense coke.During this long period of desultory operations many small openings have been made scattered over a wide area in this general region, indicating very extensive occurrence of the coal measures, although systematic exploration work has not been undertaken. However, current development work of the Banco Minero del Peru has opened up several substantially parallel highly inclined or vertical beds of workable thickness and has followed these deposits to sufficient lateral extent to prove fairly well the existence of substantial reserves on this property."

Mar 1, 1948

By C. Ortuglio

The effect of cracking by increasing the free space above the charge on the composition and yields of the volatile products from carbonization of Pittsburgh-bed coal and one industrially used blend from Eastern United States and one from Western United States was investigated with the BM-AGA carbonization apparatus. Increasing the free space above the charge from 1 inch to 3 inches, to 6 inches, and to 9 inches resulted in lower tar yields and increased gas and light oil yields. Anthracene and naphthalene yields were increased; quinoline and benzene insoluble fractions of both the tar and pitch increased considerably with increased free space, although the carbon content of the tars and pitches increased only slightly. Increased cracking, occasioned by the increase in free space, resulted in a decrease in the yields of tar acids, tar bases, neutral oils, olefins, aromatics, and paraffins and naphthenes. Gas composition was relatively constant; hydrogen and methane tended to increase and ethane decrease. Results of the investigation are being used to design a unit to upgrade the volatile products of carbonization by cracking the hot products as they leave the carbonization chamber.

Jan 1, 1970

By G. L. Oldright, Virgil Miller

"This paper is the eighth; of a series on smelting in the lead blast furnace, and the third' of a group on the modifications brought about by the introduction of rich charges.ACKN0WLEDGMENTSThe data that appear in these articles were obtained through the courtesy of the operators of the Bunker Hill smelter at Kellogg, Idaho. The authors take this opportunity to express their appreciation to Stanley A. Easton, the vice-president and general manager, Frank M. Smith, smelter director, and to A. F. Beasley, the smelter superintendent, and his staff.INTR0DUCTI0NIt has been noted that the gases issuing from the top6 of the charges in the International Smelting Co.'s furnaces at Tooele, Utah, were very similar in composition to the gases from the top of the iron blast furnace, as they contained about 26 per cent of CO and 12 per cent of C02, the rest of the constituents being mainly nitrogen with a very little hydrogen and oxygen. It has been seen that where the column of coke was sufficiently high, the production of C0 gas to carry out the reduction of lead ores was accomplished in about the same manner as in a gas producer. In some cases, there was a little oxygen in the ""top gas"" -- usually not over a few tenths of a per cent, but at times amounting to several per cent. The presence of this gas was attributed to irregularities in operation that permitted air to come up through the tuybres to the surface without meeting any coke that was incandescent. Only a hundredth of a per cent or so of sulphurous oxides was present in the gases issuing from the top of the furnace."

Apr 1, 1931

By W. W. Adams

"The fifth annual National Safety Competition conducted by the United States Bureau of Mines to determine the best safety records at mines and quarries during the calendar year 1929 has been concluded, and the general results of the contest are presented herewith. To the winner in each of the five groups into which the contestants were divided there has been awarded the bronze trophy 'Sentinels of. Safety,' donated by the Explosives Engineer magazine. The trophy for bituminous coal mines was won by a mine in Alabama; that for metal mines by an iron-ore mine in Michigan; that for nonmetallic mineral mines by a salt mine in New York; that for quarries and open-cut mines went to a limestone quarry in Michigan;. the trophy provided for anthracite mines was, of course, won by a mine in Pennsylvania, as all of the anthracite mines participating in the contest are situated in that State.Winners of the trophies were selected by a committee of sward in accordance with rules governing the contest and on the basis of accident records furnished by the various companies to the Bureau of Mines. These records were summarized by the bureau and the results submitted to the committee. Members of the committee are W. H. Cameron, managing director of the National Safety Council. William Green, president of the American Federation of Labor; James F. Callbreath, secretary of the American Mining Congress; T. T. Read, Vinton professor of mining of Columbia University and editor of 'Mining and Metallurgy'; C. B. Huntress, executive secretary of the National Coal Association; A. J., Curtis, assistant to the general manager of the Portland Cement Association; A. T. Goldbeck, director of the engineering bureau of the National Crushed Stone Association.Thirty-four States were represented in the l29 contest. Among the plants which participated were 68 bituminous coal mines, 29 anthracite mines, 54 metal mines, 19 nonmetallic mineral mines, all of the foregoing being underground mines, and 141 quarries or open-cut mines. A total of 106,533,006 man-hours of work was reported by all of the companies. Accidents during the year numbered 7,008 and represented a period of disability equal to 986,306 man-days. Hence the accident-severity rate for all plants combined represented 9.3 man-days of disability for each thousand man-hours of exposure to hazard. Similarly, the combined accident-frequency rate for all plants showed that 66.3 accidents occurred for every million man-hours of exposure to hazard. Both of these rates indicated an improvement over the combined rates for all plants in the previous year's contest. The reduction in the accident-severity rate centered chiefly in the metal mine group, though all except the quarry and open-cut mine group shared in the reduction; the improvement in the accident-frequency rate was in all croups except anthracite and metal, the rate for the former having increased while that of the latter remained unchanged."

May 1, 1930

By Kenneth H. Johnston

The Weber pool in Washington County, Okla. (fig. 1), covers an area extending from 2 miles east and slightly north of Bartlesville, Okla., to a point approximately 2-1P tiles northeast of Dewey, Okla. The pool is a part of the area designated by the Standing Committee on Oil Field Nomenclature, Kansas-Oklahoma Division, Mid-Continent Oil & Gas Association, as the Bartlesville-Dewey field. In the following discussion of the geology, development, and exploitation of the Weber pool, the writers, by means of structure maps, cross sections through various parts of the reservoir, and tabulated development data and production statistics, have recorded salient information on a field that was developed before .1910 in an Area that has been repressured since 1926. The total oil production to January 1, 19.0., from the 2,639 developed acres considered in this report, was approximately 14 million barrels, or a recovery of about 5,3;2 barrels per acre, or 227 barrels per acre-foot. The production of the estimated 18 million barrels of recoverable oil remaining in the Bartlesville sand reservoir will require the initiation of additional secondary-recovery practices on some of the leases and the application of a more systematic repressuring program on others.

Jan 1, 1950

By John C. Edwards

A fire location computational model was developed by the U.S. Bureau of Mines. The model can determine all the possible paths in a mine that smoke can travel from a fixed fire source to a smoke detector. The associated FORTRAN computer program can be utilized to determine the minimum travel time from a source fire to a smoke detector. The difference in travel time from an isolated fire source to two or more detectors can be used to isolate those airways in which the source fire is located.

Jan 1, 1990

By W. P. Yast, R. R. Slyers, J. H. Hildebrand

 The Bureau of Mines, in conducting investigations of atmospheres in mines and tunnels for the purposes of determining and combating hazards to the health and safety of workers, has from time to time closely cooperated with municipal, State and Federal agencies in safety work in engineering and ventilating probleme. Recently the writers have conducted experiments with animals and men breathing helium-oxygen mixtures under pressure. The object of this work was to determine whether helium-oxygen atmospheres can be utilized to advantage in place of normal air for caisson and diving work. In such work the permissible pressures and times of compression and decompression are limited by the physiological effects on man. The major effect is that the nitrogen, (which is the inert con- stituent of normal air and is absorbed by the body tissues and fluids in abnormal amounts when under pressure,) tends to form bubbles in the tissues on too rapid discompression from high pressures. The Bureau of Mines is interested in this problem on account of the pos- sibilities of mitigating caisson illness in tunnel construction and other engine eering operations requiring men to work in compressed air. In addition, the Navy Department is interested on account of the possibilities for extending the range of salvaging and marine engineering operations. The results of the experiments conducted by the writers lead to the following conclusions: Helium is without odor or taste and has physical properties which promise to be of interest physiologically and which have been found to have possibilities of creat practical use, especially in making a synthetic atmosphere that will re- duce the hazard of caisson disease. The substitution of helium for the nitrogen ordinarily present in the air we breathe has been found to result in an atmosphere which it as respirable as that provided by nature. The results obtained indicate that helium not only has the advantage of being less soluble than nitrogen, but

Feb 1, 1925

By Oliver Bowles

Slate possesses many admirable qualities, not only as a roofing material, but for blackboards, electrical switch boards, and for various structural uses such as stair trends, floor tile, baseboards, and sanitary enclosures. The American slate industry was established manor years ago, and has made remarkable progress, particularly during the past five years. One of the chief drawbacks to more rapid expansion is the high percentage of waste which reaches 75 to 94 per cent of gross production. Much of this waste is duo to rock imperfections over which man has no control, but a careful study of tae industry by the Bureau of Mines over a period of years indicates that an undesirably large percentage of the marketable slate is wasted in the processes of quarrying and manufacture. The initial step in quarrying slate is to separate from the solid ledge masses of a size that ray be conveniently removed from the quarry. This first step entails a greater waste of material than any subsequent process, and, therefore, invites the most earnest effort toward waste reduction. Attention has consequently been directed toward possible improvements in methods of making primary cuts in the quarry floor. A study of European practice with the wire saw, together with theoretical consideration of its advantages, convinced the writer that it possessed sufficient merit to justify its use as a primary slate cutter in American quarries. No practical conclusion in this matter could be reached except by experiment. Therefore, the desirability of obtaining equipment and trying it out under actual conditions of operation was urged upon operators. While no doubt the equipment could be readily manufactured in America, it had already been developed to the point of practical use in Europe; therefore the writer urged the desirability of purchasing one completely equipped wire saw in Europe, and determining through tests whether it gave sufficient promise of success to warrant its manufacture in America.

Jan 1, 1927

By S. R. Zimmerley

[In the course of a flotation investi~ntion, a siliceous gold ore was ground ir, R 'ball mill to ~inils 300-mesh. It mas found that the small mount of zlus 300-~esh mnterial had a go12 assw approximately twice that of the oricinal ors, md thst this oversize ~roduct also contained much abra?.ed iron. >!oreover, the gold assay of the abraded iron, which was separated ma~etic-dl:;, wno ei::ht tiaes tkat of the ore. These facts sug,~estsd th~t sone r3laticnshin existed between the abnormally high .gold content and the preseace of abrade4 iron. It was ciecided, therefore, to investl~ate furtkor ths acsoclation of the ;old nith the iron abraded from the balls durir-g grincing. As a nrelininary ex?rr>hent, a samy?le of siliceous gold ore 786 grolznd for 1-1/2 hours i;l 3 ball mill and the nuln was divided into two products electri~mag-etically. The racult s follow: ]

Jan 1, 1937

By R. E. Peterson

Scrap iron is partially oxidized at elevated temperatures in the selective oxidation process to produce iron oxide and a dense residual metal of high purity. Investigation of the process was confined to converting automobile hulks into useful products. In one test series, compressed, sheared automobile scrap was processed at 1,000° C in a 36-foot-long rotary kiln at feed rates ranging from 300 to 1,200 lb/hr. Less fuel was required to maintain the temperature at the higher feed rates because of the heat generated from the burning of the combustibles and the oxidation of the iron. The bulk density of the residual metal exceeded 75 pounds per cubic foot. In an attempt to lower the quantity of contaminants in the residual metal, another test was designed using automobile hulks which had been prepared by ripping, a low-cost method of scrap fragmentation. Before oxidizing the ripped scrap approximately 62 percent of the total copper was removed in a tumbling, screening, magnetic separation and hand-sorting system. Cast iron made from the residual metal obtained by selective oxidation contained 0.15 percent copper; iron oxide scale obtained from the kiln averaged 0.13 percent copper. Pellets made from the scale demonstrated compressive strengths necessary for blast furnace reduction; lead and zinc were removed by volatilization when the induration was performed in a reducing atmosphere.

Jan 1, 1972

By Gerald A. Muson, Fremont F. Clarke

"INTRODUCTION The use of scrap mica as an industrial raw material has grown rapidly during the past two decades. Demands by various industries for ground mica for use in the roofing, paint, rubber, plastics, and wallpaper trades as well as for less extensive uses in insulation, oil-well drilling, welding, pipeline enamel, decorative material, and for other purposes exceed present (1947) supplies.A small proportion of the raw material used comes from the Black Hills of South Dakota, where casual recovery has been practiced in the exploitation of pegnatite deposits for more valuable minerals. The annual production of scrap mica in the Black Hills for the years 1939 to 1946 is shown in figure 19. 4/Although small, this production of scrap mica materially augments the incomes of numerous operators.Volume production of mica would offer attractive opportunities for obtaining steady and more economical supplies of the rare minerals as byproducts. Appreciable supplies of beryl, lithia minerals, sheet mica, tantalite-columbite, and cassiterite could accrue. Furthermore, a stable scrap-mica production would complement the production of quality feldspar, for which the Black Hills pegmatites are noted, and would help balance the economy of pegmatite mineral production.Mechanical methods of separation are requisite to production of enough scrap mica to be generally profitable. Various phases of the characteristics end treatment of mica have been investigated by the Bureau of Mines. A bibliography of these reports is appended.In 1945 the Bureau of Mines conducted pilot-plant tests to recover scrap mica by selective screening of crushed pegmatite. More recently the problem has boon studied in the Pegmatite Research Laboratory to aid in developing technological methods by which scrap mica may be separated from crushed pegmatite."

Feb 1, 1949

By E. J. Kloos

The Bureau of Mines developed a test for evaluating gas masks designed to protect against phosphine gas; phosphonium iodide is used as a source of phosphine. Gas masks approved by the Bureau for respiratory protection against phosphine include the GMC-SS-1, Mine Safety Appliances Co.; the LG-10 and LG-10G, Willson Products Division, The Electric Storage Battery Co.; and the 084-PHOV-R, Acme Protection Equipment Co.

Jan 1, 1966

By S. H. Katz

In the Bureau of Mines investigations of respiratory apparatus, a laboratory study of dust respirators has been conducted, and the results will be published in detail as a technical paper. Many industrial dust respirators, and many fabrics and filtering materials were tested. The principal results of these tests, and the conclusions drawn from them, are presented below. Reference to the patent literature discloses numerous types of dust respirators, mostly based on the filter principle. The present study included only representative filter-type respirators, purchased on the market.

Jan 1, 1926

By Timothy W. Beck

Roof bolter occupations in underground coal mines continue to experience overexposure to respirable dust. One potential source of dust in roof bolting operations is the exhaust from the roof bolter dust collection system. A wet exhaust conditioner (?water box?) has been developed to reduce dust emissions from the exhaust of the vacuum dust collection system on roof bolting machines. The exhaust conditioner consists of a muffler chamber and a water chamber with four internal partitions to direct airflow over the surface of the water. The National Institute for Occupational Safety and Health conducted a series of laboratory tests to assess the respirable dust capture ability of this device as compared to the standard exhaust muffler. To determine the dust collection efficiency, both devices were placed in the exhaust stream of a simulated roof bolter dust collection system. Gravimetric samplers were operated upstream and downstream of the exhaust conditioner and muffler to evaluate the ability to capture both respirable coal and limestone dust. Researchers observed a 41 percent reduction in dust concentrations for the water exhaust conditioner in the laboratory configuration. Significant levels of dust deposition in the sampling chambers may have contributed to this effective capture rate.

Jan 1, 2010

By P. M. Sullivan

This report describes a new application of electroamalgam metallurgy in recovering all the zinc as refined metal from galvanizers' sal skimmings. Pure zinc was recovered by electrolysis of skimmings leach liquors in amalgam cells. The following information was gained as a result of literature studies and subsequent laboratory investigations. 1. Reports in the literature indicate that pure zinc can be recovered from chloride solutions with the aid of amalgam cells. From Europe it was reported that amalgam cells could be used to recover pure zinc and chlorine from leach liquor obtained from pyrite cinders following a chloridizing roast.

Jan 1, 1956

By Harry F. Weaver

Rivers in industrial and raining areas frequently are contaminated by material dumped into them causing the water to carry in suspension large amounts of silt, which subsequently is deposited alone; the banks and, ultimately on the agricultural lands if the water is used for irrigation purposes. Two common examples of this practice are the dumping of breaker refuse in the anthracite region of Pennsylvania and the dumping of tailings from the metallurgical mills in various metal-mining districts. Studies in stream pollution and its resultant problems are very important, and surveys are constantly being made by Federal and State agencies, as well as by private companies, to determine the quantity of solids actually being carried by these watercoarses. These studies require accurate sampling of the silt-carrying water to determine the amount of solids within reasonable limits. A device that will obtain reasonably accurate samples of material from silt-bearing streams is described in this circular.

Jan 1, 1943

By Dana T. Updyke

An evaluation was made of one of several improved underground communication systems sponsored by the U.S. Bureau of Mines. The system evaluated was installed in a typical metal/non-metal room and pillar mine and utilized UHF repeaters connected to a unique distributed antenna and passive reflector system which provided mine-wide communications. A microprocessor controlled data collection system was assembled and installed for the evaluation. Data consisting principally or times and durations of messages and identities of the originating transceivers was collected between February and August of 1982 (6 mos.). Analysis of the data shows that the principal benefits are reduction in time required for unscheduled maintenance and repair, enhancement of safety, and better coordination of production activities. A cost benefit analysis shows a net benefit over cost, although it is also concluded that the capacity of the system is greater than can be justified by current activity in the mine.

Jan 1, 1983

By Earle S. Burnett

This report outlines the experimental procedures for using a Burnett apparatus to obtain compressibility coefficients for multiphase, multicomponent fluid mixtures. The conventional Burnett method is described briefly whereby multiphase compressibility data can be obtained by first determining the compressibility factor, Z, as an isothermal function of pressure alone. Then starting at conditions of temperature and pressure where Z is known, the fluid is cooled at constant volume to some lower temperature at which the resulting pressure is measured, and a corresponding value of Z is obtained from a fundamental relationship between compressibility factors, pressures, and temperatures at constant volume. The isochoric treatment of the fluid, extended to still lower temperatures and along other isochors, eventually results in compressibility determinations for the whole two-phase system thus covered experimentally.

Jan 1, 1963