Search Documents

By C. C. Popoff

The development of glass-making industries in the Pacific Northwest as well as other industries that use pure silica has been retarded by lack of local supplies of low-cost raw material. Several quartz deposits along the Skagit River constitute the only known source of relatively pure silica within the range of cheap transportation to the Seattle industrial area. Although some silica has been mined from these deposits, very little information regarding their size, grade, and other physical characteristics has been available to the general public. As a part of its program of investigation of the mineral resources of the Pacific Northwest, the Bureau of Mines assigned the writer to examine the Skagit River silica deposits in October 1946. This report presents the factual data obtained from an examination of the so-called Stoner, Bacon Creek, and Pressentin deposits. These deposits are the largest and most easily accessible known to exist in the area. The deposits are near Marblemount, which is on State Highway 17A. They are within 1 mile to 1-1/2 miles of the Skagit. River Railway, which provides transportation to Seattle, a distance of 130 miles. None of the deposits has been developed thoroughly. The Stoner deposit, however, has been developed by a quarry about, 5,0 feet square and has been exposed by hydraulic removal of the overburden throughout a distance of 180 feet along the hanging wall of the vein

Jan 1, 1949

By Frederick W. Horton

With large deposits of low-grade molybdenum ore and a latent market for molybdenum, which with development might perhaps equal that for tungsten, the United States has for years made no pro- duction of molybdenum ore worthy of mention. In fact, during the decade previous to 1914, there was no output of molybdenum ore in this country except in 1905, 1906, and 1907, when a few small lots of molybdenite and wulfenite were marketed." To ascertain why this possible source of economic wealth should remain undeveloped, the United States Bureau of Mines undertook an investigation in 1914, with a view of assisting the establishment of a molybdenum industry in this country. A preliminary review of the situation showed the following conditions: Briefly there was a lack of any considerable demand for molyb- denum for the one known use that might consume any large tonnage of it, that is, for the manufacture to certain alloy steels to which molybdenum imparts properties roughly similar to those produced by tungsten. It was at once evident that the market for molybdenum in alloy steels must be developed, or that extensive new uses for the metal must be created, before the demand would be sufficient to war- rant any extensive mining of molybdenum ore. Investigation showed that one of the chief factors in retarding the development of any demand for molybdenum by the alloy-steel trade was that manufacturers who might use, or might investigate the possibilities of using, the metal were kept out of the market by the fear of not being able to obtain steady supplies. On the other hand, those who might be interested in the development of some of the extensive low-grade molybdenite or wulfenite deposits in this country were prevented from doing so by the small visible demand and the fear that any large production would glut the market. Owing to these conditions the mining of molybdenum has in the past been confined almost entirely to small-scale operations on high-grade streaks of molybdenite ore, and the methods of recovery have been limited largely to cobbing and hand picking.

Jan 1, 1916

By J. A. Rowland

Manganese-copper alloys containing 60 percent or more electrolytic manganese exhibit an unusual combination of high vibration damping capacity with good strength properties. Properties of the pure alloys were first studied in the laboratories of the Federal Bureau of Mines and have been described in a series of technical papers1/ published from 1941-49. The unusual characteristics of these manganese-copper alloys attracted the attention of research metallurgists and several additional investigations have also been reported in the literature.2/ The engineer, also, was attracted by the combination of high strength and high vibrational damping capacity possessed by these alloys. A wide field of application in structural and machine design was obvious. However, serious difficulties encountered in commercial fabrication of structural or machine components from the alloys retarded attempts at their practical utilization. For this reason the Federal Bureau of Mines, in cooperation with the United States Navy, Bureau of Ships, undertook a program designed to develop practical methods for fabricating a selected group of the high-damping alloys. It is the purpose of this paper to summarize a part of that investigation in a form suitable for use by the metallurgist interested in commercial fabrication of the alloys.

Jan 1, 1955

By G. W. Jones, R. E. Kennedy

"INTRODUCTION Information relative to the ignition temperatures of acetylene and acetylene-air mixtures has become of particular interest recently due to a number of explosions that have occurred in 500-pound, double-rated, medium-pressure acetylene generators in shipyards on the West coast. Various suggestions have been made as to the causes of these explosions prominent among which has been that air finds its way into the acetylene generators during abnormal operation or that air remains in the carbide hopper of the generator following the purging and charging operations.This raises the question as to how and to what extent the presence of small percentages of air in acetylene affects the ease of ignition of such mixtures at the various operating pressures of the acetylene generators. The range of operating pressures in the 500-pound, double-rated generators involved in the explosions may vary from below atmospheric to 15 pounds gage.The present report gives the results of an investigation made to determine the effects of pressure on the ignition temperature of pure acetylene and of acetylene containing varying percentages of air:EXPERIMENTAL Apparatus A preliminary investigation showed that a heated quartz surface gave lower ignition temperatures than other material tested.A ""hot-spot"" method of ignition was found desirable in the case of the acetylene mixtures since the violence of the explosions was reduced by keeping most of the test mixtures at room temperature. Explosive violence was reduced further by using an ignition tube 17 mm. or less in diameter."

Mar 1, 1945

By Magnus Persson

ISO8662-4, “Hand-held portable power tools - Measurement of vibrations at the handle - Part 4: Grinders” is under revision. The new revision shall harmonize ISO 20643 “Mechanical vibration - Hand-held and hand-guided machinery - Principles for evaluation of vibration emission” which, among others, requires measurements in three directions and declared values related to the upper quartile of real-use vibration. To get the most suitable test method, a round robin test was made for evaluation of the two test methods proposed by the ad-hoc group working with this standard revision. Methods Seven laboratories measured the vibration from four grinders of different sizes, with and without autobalancing units. The laboratories come from universities, health & safety laboratories and grinder manufacturers. Two measurement methods are evaluated with respect to repeatability and reproducibility: 1. Grinding on a well-defined mild steel bar with depressed center wheels according to detailed test instructions. The test sequence starts and ends with 10 seconds of running the grinder in the air, when measuring the unbalance contribution to the vibration coming from the unbalance of the grinding wheel. Between these runs the average vibration during 60 seconds of grinding is measured. Three operators do five grinding tests per grinder. 2. Measurements using an aluminum unbalance disc similar to the one defined in ISO8662-4. Each operator runs the grinder four times, between each run the unbalance is moved 180 degrees to avoid variations caused by the play between the test wheel and the spindle. The averaging time is 10 seconds. Each grinder is tested by three operators. Repeatability is the spread within a lab between operators and over short time period for one machine and reproducibility is the spread between laboratories and over longer time periods for one machine. Instrumentation and transducer location are chosen according to ISO8662-4 and circulated test instructions. Results Both the repeatability and reproducibility is poor for the real grinding test, see figure 1. The coefficient of variation for repeatability is approximately 40% higher for the grinding test and the coefficient of reproducibility is 60% higher for the grinding test than for the unbalance disc test.

Jan 6, 2006

By Wm. W. Odell

In distributing natural and mixed gas, the industry is each year confronted with the problem of manufacturing gas in increasing amounts as the supply of natural gas becomes more nearly exhausted. The manufactured gas is now used in mixtures with the still available natural product, and will subsequently be used straight as a substitute gas. The gases that might be considered, and are producible by tried and developed processes, include water gas, carbureted water gas, and coal gas. Singularly, these gases can be used in this manner in ordinary appliances only when proportional amounts of them in the mixtures do not vary beyond rather definite limits, unless burner adjustments are made. The limits are defined by the specific gravity, content of inerts, and burning properties of the respective gases. Anticipating a future standard for city gas lower than that of natural gas during the period when considerable natural gas is available, there is justification for considering the possibility of re-forming natural gas and making a product that has substantially the same properties as other gases which can readily be generated. This report gives the results obtained during a series of tests made under a cooperative agreement by the U. S. Bureau of Mines with the Ohio Fuel Gas Co., re-forming natural gas at Toledo, Ohio, in full-scale operation in a water-gas generator having a grate area of 25.1 square feet. ACKNOWLEDGMENTS The Ohio Fuel Gas Co. constructed a special water-gas generator for the tests and provided men and the necessary funds for its operation. Appreciation is expressed for the general spirit of helpful cooperation which was evidenced in the activities of all those who took part in the work. Particular acknowledgment is made of the assistance rendered by C. W. Wallace, manager, and by C. F. Cramer, superintendent, and A. Upp, foreman of the plant.

Jan 1, 1929

By G. W. Reimers

Metastable pyrophoric wüstite (FexO, with x between 0.89 and 0.95) was found to be much easier to grind to colloidal state than were its stable disproportion products magnetite or iron. The grinding of polycrystalline magnetite appears to be complicated by the magnetic flocculation arising from interparticle attraction. This is superimposed on the attraction of a fluctuating electric dipole for a neighboring induced dipole. More than 85 pct of the tumbling time was saved by grinding antiferromagnetic wüstite instead of the ferrimagnetic oxide of iron (Fe304). Disproportionation of colloidal wüstite to the stable ferromagnetic and ferrimagnetic colloidal particles of alpha-iron and magnetite, respectively, was accomplished rapidly at temperatures above 250° C but below 570° C, the eutectoidal stability point of the wüstite phase.

Jan 1, 1972

"INTRODUCTIONMany of the facilities and much of the equipment available to the Generic Mineral Technology Center for Respirable Dust are highly specialized and therefore, unique to the universities associated with the Center as illustrated in FIGURES 30 through 39.For example, a sample bank of 1300 U.S. coal specimens housed in the Coal Research Section, Deike Building of The Pennsylvania State University has been characterized for physical, elemental, mineralogical and maceral compositions. The results of this research have been used to initiate a study of the relationship between pneumoconioses and coal properties. Selected samples from this bank have been used in animal (primate) studies at the Milton S. Hershey (Penn State) and West Virginia University Medical Centers. These laboratory facilities for research in the medical and biological disciplines is state-of-the-art and includes a primate colony where dust research is currently underway. The Materials Research Laboratory and the Rock Mechanics Laboratory at PSU, and the Mechanical Systems Design and Control Laboratory, the Rock Mechanics Laboratory and the Mine Electronic System Laboratory at WVU are equipped for fundamental research on dust generation and characterization. While the majority of respirable dust research projects fall into these two categories, dust generation and characterization and interaction of dust and lung, there are other laboratory facilities available to the Center which are unparalleled in the type of equipment and expert personnel that they contribute to the program. The Mine Particle Laboratory located at the University of Minnesota and the Diesel Engine Laboratory at Michigan Technological University are examples. They house equipment and instrumentation that is unique to these facilities. much of it having been developed specifically for dust research by the research scientists there. The dust collection equipment and the fine particles measurement, characterization and analysis apparatus are essential to research in the areas of dust collection, particle characterization and diesel particulates. In addition to university laboratories, the research facilities of the National Institute for Occupational Safety and Health (NIOSH) are available to the Center through its relationship With West Virginia University."

Aug 31, 1989

By Paul Sands

Single- and two-stage tests were made with 6-inch, coal-cleaning hydrocyclones to determine the effect of hydrocyclone geometry, operating conditions, and feed composition on performance. Most of the testing was conducted in an open-circuit pilot plant that had a maximum capacity of about 9 tons per hour. The coals used in the investigation had top sizes of 1/4 inch and 28 mesh. Considerable latitude was found in the range of geometry variables that could be used without affecting performance adversely, although a certain minimum ratio of overflow to underflow openings had to be maintained for best operation. Two-stage cleaning proved distinctly better than operation with a single hydrocyclone, because clean coal lost in the refuse product of the primary unit can be partly recovered in the secondary. There is an unusually great difference in the specific gravities at which the individual sizes of the feed are separated in the hydrocyclone. This militates against high efficiency because maximum yield occurs when all sizes are cleaned at the same specific gravity. The size composition of the feed and, more particularly, the size composition of the impurity have a greater influence on the efficiency attainable in the hydrocyclone than in most other types of fine-coal cleaners.

Jan 1, 1968

By F. R. Lee

THE Bureau of Mines was established in July 1910 to conduct research and to establish standards for mining equipment and practices which would conserve human life, natural resources, and property in the mineral industries. Several lists of equipment approved by the Bureau as permissible for use in gassy coal mines have been issued since then. The lists covering all approved equipment except breathing apparatus and explosives have born consolidated into two publications: Bulletin 343. Permissible Equipment Approved to January 1, 1953, and Information Circular 8220, Permissible Mina Equipment Approved By The Bureau of Mines During 1953-62. The, purpose of this publication is to supplement Bulletin 343 and Information Circular 8220 with a listing of permissible equipment approved during 1963 and 1964. The schedule, (standards) under which equipment listed herein have been approved are, as follows (cities and dates of approval and revision are, given in footnotes) : Schedule 2F,3 schedule 6D,4 schedule 7C,5 schedule 8C,6 schedule 9B,7 schedule 10C,8 schedule 12D,9 schedule 22,10 schedule 24,11 schedule 25B,12 schedule 25B,13 schedule 29A,14 schedule 30,15 and schedule 31.16

Jan 1, 1966

By Graham W. Marks

The general positions of the absorption maxima of aqueous solutions of the violet and green isomers of chromic sulfate the visible spectral region have long been known, but, to the knowledge of the writer, no comprehensive studies have ever been made. To gain further knowledge concerning these inorganic complexes and to investigate the possibilities of developing an analytical method for determining the concentrations of the violet and green isomers in a mixture, a more complete investigation was made in the spectral range from 325 to 850 millimicrons.

Jan 1, 1951

By Terry J. Close

The Welcome Creek Wilderness has small, dispersed gold placers. Pockets in the 25.5 million yd3 (19.5 million m3) of alluvium along Welcome and Rock Creeks have as much as $5.61 gold/yd3 ($7.34/m3) at $500/troy oz ($16.08/g). All the alluvium averages 20.1 cents gold/yd3 (26.3 cents/m3). Because of the low average gold content large-scale placer mining would not be economically feasible. Small-scale selective pocket mining, however, may be profitable. The alluvium along the streams in the Wilderness has little apparent potential for production of sand, gravel, or stone because alternate sources are closer to markets. The four lode prospects known within the Wilderness appear to have low mineral potential. No oil, gas, uranium, or geothermal energy sources are known to be present.

Jan 1, 1982

By V. F. Parry

[Subbituminous coal or lignite when stored in random piles or in ordinary bins in which the temperature fluctuates and air circulates quickly undergoes objectionable physical and chemical changes, which decrease the utilization value of the fuel and increase its tendency to ignite spontaneously. Slacking takes place, and the heating value decreases. These changes are accelerated by fluctuations of temperature and by circulation of air through the storage space. When such coals are exposed to the weather they lose moisture rapidly. If evaporation from the surface of a lump proceeds at a faster rate than that at which it is replaced by moisture from the interior, the rate of shrinkage at the surface is greater than that at the interior; consequently, stresses are generated at the surface which cause the coal to disintegrate. Likewise, when moisture is absorbed by the air-dried surface the outside layers expand at a faster rate than the interior, which results in further break-down. As these cycles are repeated the lump may disintegrate completely. Therefore, successful storage of low-rank coals depends on control of the factors that influence change of moisture.]

Jan 1, 1941

By V. F. Parry

Subbituminous coal or lignite when stored in random riles or in ordinary bins in which the temperature fluctuates and air circulates quickly undergoes objectionable physical and chemical changes, which decrease the utilization value of the fuel and increase its tendency to ignite spontaneously. Slacking takes place, and the heating value decreases. Those changes are accelerated by fluctuations of temperature and by circulation of air through the storage space. When such coals are exposed to the weather they lose moisture rapidly. If evaporation from the surface of a lump proceeds at a faster rate than that at which it is replaced by moisture from the interior, the rate of shrinkage at the surface is greater than that at the interior; consequently stresses are generated at the surface which cause the coal to disintegrate. Likewise, when moisture is absorbed by the air-dried surface the outside layers expand at a faster rate than the interior, which results in further break-down. As these cycles are repeated the lump may disintegrate completely. Therefore, successful storage of low-rank coals depends on control of the factors that influence change of moisture.

Jan 1, 1941

By Albert W. Deurbrouck

This report describes the preparation characteristics of the significant coalbeds in Russell County , Va . Almost 2 million tons of coal was mined in 1961 ; 75 percent of the coal was cleaned mechanically in preparation plants in the county . The coal of Russell County is ranked as medium- to high- volatile bituminous , contains small amounts of sulfur , and generally requires some cleaning to reduce the ash content to limits acceptable for metallurgical purposes .

Jan 1, 1963

By Otto Ruhl

"INTRODUCTION With the conclusion of the war and the ensuing readjustment of industry to peacetime conditions, the Bureau of Mines recognized that definite and complete figures on the reserves of zinc and lead ores in the Tri-State District would be needed for an evaluation of the problem of reconversion. In October 1945 its engineers began examination of all the mines and pros¬pects in the Tri-State area and assembling of the basic data for a complete detailed estimate of the reserves of the field. Six to twelve months will be required to complete the report with the personnel available; therefore, it has been deemed advisable to provide as much data as possible for imme¬diate use. Accordingly, a confidential report prepared in January 1944 for the use of and in cooperation with the War Production Board has been brought up to date to form the basis of this preliminary estimate of reserves.The 1944 report has been revised by first subtracting from the reserves then set up for each mill group the amounts mined and milled by those properties for 1944 and 10 months of 1945, with November and December estimated. These production statistics were taken from the monthly reports of the Metal Economics Division of the Bureau of Mines. The remaining reserves were then adjusted by additions of tonnages of new reserves disclosed by developments during the years 1944 and 1945. Such additions were based upon the data furnished by various operators, upon estimates supplied by the Federal Geological Survey District Office at Miami, Okla., and upon estimates of the engineers of the Bureau of Mines Joplin field office.It is apparent from the work so far accomplished in the detailed exami¬nations now under way that the final estimate of reserves will probably be somewhat greater and will differ to a certain degree from these preliminary totals, not only as to the tonnages of ere but also as to grades and distribution by areas. This is due to the fact that all the factors of development, exploration, and geology are being considered in the present examination and report for each individual mine and prospect, whereas the previous reports covered only the immediate development factors surrounding each mill group then in active operation or projected for operation at some early date in accordance with the possible needs for war production."

Aug 1, 1946

By W. W. Adams

Two important facts stand out as features of the metal- and nonmetal-mining4 industry of the United States in 1941 as compared with 1940: First, the number of employees and man-days of employment increased; second, accident-frequency rates, both fatal and nonfatal, decreased. Reports from mining companies to the Bureau of Mines covering underground, open-pit, and surface operations for 1941 re¬vealed the largest number of men employed since 1926 and the largest number of man-days worked since 1929. The combined fatal and non¬fatal accident-frequency rate for 1941, calculated on a basis of one mil¬lion man-hours of exposure to hazard, was (except for 1931 and 1932) the lowest since 1911, the earliest year for which figures are available. During this 31-year period, only 1938 and 1939 showed lower fatality rates, and only 1931 and 1932 had lower nonfatal-injury rates. Operating companies reported that 9,620 mines were active during all or some part of the year. These employed 125,290 men, an increase of more than 4 percent over 1940. The total volume of work performed at all mines, measured in terms of man-shifts, increased to nearly 32 million, a gain of 10 percent; man-hours of employment rose to almost 254 million, an increase of 10 percent over the 231 million man-hours worked in the previous year. The year's operations resulted in an average work-year of 255 days per man, an increase of 13 days per employee over the average working time in 1940. Although the 8-hour day prevails generally at most mines, the industry as a whole averaged 7.94 hours per shift, as in 1940.

Jan 1, 1944

By W. J. Fene

The lowest number of fatalities from coal-mine explosions in the United States in any year since records have been kept was the total of 8 in 1949 and again in 1950. Even incomplete records as far back as 1870 reveal a larger annual loss of life from explosions. From 1890 to 1948 the lowest annual loss was 32 in 1946. A smaller total of 15 fatalities was reported in 1952. Figure 1 shows the total yearly loss of life from explosions in all coal mines since 1880. Those in anthracite mines alone are shown by the shaded area. The erratic variation of the chart line shows the difficulties that have confronted the industry in the struggle to control and eliminate mine explosions. Potential hazards have existed in marry mines without realization that only a small change in conditions could initiate a disaster. Many disasters causing great loss of life occurred in mines that had been regularly operated without incident for long periods. Although the number of coal-mine explosions causing great lose of life has been kept down in recent years, the exceptions still make the record anything but satis¬factory. There have been almost no widespread explosions for several years, but in a few instances many lives were lost from afterdamp. Although the violence and spread of mine explosions may be controlled, the loss of life may be heavy if many of the men happen to be in the path of the smoke and gases. For these reasons, the strictest controls must be maintained to eliminate all factors that might combine to cause even a small ignition of gas or dust.

Jan 1, 1953

By E. J. Kloos

The Bureau of Mines evaluated all previously approved gas masks to determine their ability to provide respiratory protection against each of the following six selected amines: ethylenediamine, diethylamine, n-butylamine, ethylamine, methylamine, and hydrazine. Minimum requirements were a 24-minute service life at a flow rate of 64 liters per minute (32 liters per minute for hydrazine) and an amine concentration of 1.0 volume-percent (0.5 volume- percent for hydrazine). The three masks meeting these requirements were the LG4, Willson Products Division, The Electric Storage Battery Co.; the GMD-SS, Mine Safety Appliances Co.; and the 084-PHOV-R, Acme Protection Equipment Co.

Jan 1, 1966

By F. B. Petermann

Two-stage electric smelting tests, using small submerged arc furnaces, were made on high-iron manganiferous materials from the Pioche District, Nev., and the Cuyuna Range, Minn. The object was to reduce sufficient iron in the first stage to give a slag with a favorable Mn to Fe ratio for smelting to ferromanganese in the second stage. The nodulized flotation concentrate from the Pioche District contained 29.2 percent Mn and had a Mn to Fe ratio of 2.3:l. When smelted with coke and silica or alumina as flux, more than 90 percent of the manganese was recovered in slags with Mn to Fe ratios of 10: :24:1. The Pioche slag was smelted to ferromanganese using coke and lime- stone or dolomite as flux. The ferromanganese was high in silicon but other- wise met specifications. Recovery of manganese to ferromanganese in this step was 73 to 78 percent. Overall recovery of manganese was about 70 percent. The sintered flotation concentrate from the Cuyuna Range material contained 12.9 percent Mn and had a Mn to Fe ratio of 0.3:1. When smelted with limestone as flux, about 83 percent of the manganese was recovered in a slag with a Mn to Fe ratio of about 6:1. The Cuyuna slag was smelted to ferromanganese with coke and limestone for flux. Recovery in this step was 61 percent of the manganese in a high silicon ferromanganese. Overall recovery of manganese was about 50 percent.

Jan 1, 1963