Search Documents

By H. F. Yancey

Although a general relationship exists between the two criteria used to measure sharpness of separation -error area and probable error -they sometimes give quite different appraisals of a particular washing operation. Error area takes into account how the entire raw coal was treated, whereas probable error reflects only how the material of intermediate density was separated, ignoring completely the recovery of clean coal and the rejection of heavy impurity. Error area is thus more reliable for general use. In heavy-medium cleaning, sharpness of separation decreases with increase in separating density, but ordinarily the change is not great enough to affect the yield and ash content of washed coal measurably. Therefore, distribution curves for heavy-medium units can be transposed from one separating density to another, at least in the range of separating densities ordinarily used in the United States.

Jan 1, 1955

By H. H. Fields, T. W. Goodman, Joseph Cervik

The Bureau of Mines conducted research to determine the effectiveness of long holes drilled in solid virgin coal in degasifying an area of the Pitts- burgh coalbed showing that horizontal holes drilled into a virgin coalbed from the bottom of any shaft will effectively remove methane gas in commercial quantities from the Pittsburgh coalbed. The in situ pressure at a depth of 214 feet into the coalbed and the average gas and water flows from the five degasification holes were 3 lb/in2 gage and 860,000 ft3/d and 1.7 gal/min, respectively. On June 19, 1975, after 593 days of degasification, a compressor was installed and pipeline quality gas was introduced into a commercial pipeline. As of June 1, 1976, after 1,022 days of degasification, over 753 million cubic feet of gas had been drained and 117 million cubic feet of gas had been purchased by the gas company for use in the local community of Wadestown, W. Va. The gas drained to date is six times the gas estimated to be in the area subtended by the holes. Methane emissions at the working face of 1 West mains, Federal No. 2 mine has been reduced by 50 pct, proving the value of methane drainage by horizontal degasification holes drilled from shaft bottoms ahead of mining.

Jan 1, 1976

By John B. Gayle

During studies of the various methods for determining and specifying the factors that indicate whether a particular coke is better or worse than other cokes for metallurgical uses, questions arose as to the precision of screen-analysis tests on coke. Although the usual index of precision, the standard deviation of the test result, gives a measure of the precision of these data, the experimental determination of the standard deviation for a particular set of conditions requires tests on a large number of duplicate samples. Because this procedure necessaily involves a great deal of labor, an equation for predicting standard deviations from theoretical considerations has been developed. Results predicted with this equation agree satisfactorily with the experimental values and are applicable to tests on coal, coke, gravel, and other bulk materials.

Jan 1, 1952

By John R. Troxell

"INTRODUCTION Lookout Mountain is the natural barmier that isolates Dade County from the rest of Georgia. Legend has it that Dade County seceded from the Union long before the rest of the State of Georgia and did not officially return until July 4, 1945.Coal mining began in the Lookout Mountain area in 1891, and by 1894 production amounted to about 1,000 tons daily. Present production by the two principal operating companies is about 3,600 tons monthly.In the Sand Mountain area, coal has been mined intermittently since before the Civil War, and probably 6,500,000 tons has been produced.The Bureau of Mines coal project was initiated to alleviate a possible coal shortage and to assist the State in developing coal deposits to supply State institutions and local markets. Drilling began January 1, 1945, and ended May 11, 1945, after 2,907 feet had been drilled. By this time the Georgia Power Co. became interested in northwest Georgia coal fields as a possible source of more economic fuel for their steam-driven power plants, but the Bureau continued to act in an advisory capacity to the power company until June 30, 1945."

Oct 1, 1946

By D. Harrington

A uniform hoisting-signal code for mines hoisting from more than one level, if adopted by all mining States, would be beneficial to employees and owners alike and should largely reduce the number of hoisting accidents. Misunderstood hoisting signals cause many shaft accidents involving injuries to men, damage to equipment, and loss of production from the resultant delay. Many of the metal-mining States have adopted codes for hoisting that are effective within the borders of that State but usually entirely different from the signal code, if any, in use in an adjoining State. For many years safety engineers have recognized this lack of uniformity as a distinct hazard, but a uniform code has never been adopted by the States or by the mining industry in those States that have not incorporated signal codes in their mining laws or mining regulations.

Jan 1, 1944

By Russell R. Trengrove

The Copper Canyon lead-zinc mine is in the Battle Mountain. District, Lander County, Nev. It was discovered in 1866 and mined for copper until 1935 and for copper and gold until l948, when the main production became lead-zinc ore. The rocks in the area are carboniferous (Pennsylvanian and Mississippian) sedimentaries that have been intruded by quartz monzonite of Mesozoic age. They have been intensely folded, faulted, and tilted. Lead-zinc ore occurs as sulfides disseminated along fractured zones in a conglomerate arid hornfels. Development was carried out by the Bureau of Mines in cooperation with the U. S. Geological Survey and comprised a study of the geology, making maps and. cross sections, and exploring the deposit by diamond drilling from underground. Eighteen holes were drilled, for a total of 2,594 feet. This report contains a brief history of the property and a description of mining methods and beneficiation of the ore, geology, ore deposits and drilling done by the Bureau of Mines. It also contains detailed analyses of the ore samples taken and logs of the holes drilled.

Jan 1, 1951

By Frank J. Wiebelt

Under a general program to extend the resources of mineral deposits, the Bureau of Mines examined the Quien Sabe antimony mine in October 1948. The preliminary evaluation demonstrated that a diamond-drill program was warranted co establish the tenor and persistence of the veins and permit an estimation of antimony reserves. The Bureau of Mines conducted a diamond-drilling program on the property from December 1949 to May 1950. Ten holes aggregating 2,483 feet were drilled. Nine of the holes encountered antimony-bearing vein material.

Jan 1, 1956

By K. E. Tame

The Bureau of Mines is studying possible modifications in conventional uranium ore-processing steps to confine and permit controlled disposal of radioactive wastes. Surveys of Ra226 contamination of liquid wastes from uranium mills indicated that the Vanadium Corporation of America plant at Durango, Colo., had one of the more urgent problems. A possible procedure for minimizing the waste disposal problem was to reuse the waste solution in the mill--in effect, erasing the need for disposal of liquid waste. In examining this possibility, interlocked bench-scale leaching and solvent extraction tests simulating the Durango flowsheet were made. The simulated reuse of barren raffinate for leaching and washing was carried through three separate campaigns of 9, 12, and 35 cycles each.

Jan 1, 1961

By O. M. Bishop

From October 1943 to March 1944, the Bureau of Mines conducted core drilling at the Victory fluorspar mine, Hardin County, Ill. to test the Fredonia limestone and the included sub-Rosiclare sandstone zone beneath the existing stopes. Twenty-one vertical holes were drilled to an average depth of 60 feet. Ore was penetrated in six holes. Since its discovery in 1927, the Victory mine has produced approximately 5 percent of the total fluorspar mined in the United states after that date. The ore discovered in the early mine development is now exhausted, except that contained in pillars drifting to the northeast has partly developed one substantial ore body, and company drilling has indicated another nearby. The increasing need for fluorite for war use in 1943 suggested the desirability of mining the pillars, provided it could be established that no ore beds existed below the stopes or in areas to which access would be obtained through the present workings. This work describes the work accomplished during the project and presents the data obtained.

Jan 1, 1948

By K. L. Cashdollar, C. K. Man, J. R. Gibbins

Oxyfuel combustion is currently one of the principal technological options being considered for capturing carbon dioxide from pulverised coal power plants. In oxyfuel combustion, coal is burnt in a mixture of recycled flue gases and added oxygen instead of in air. In principle this yields a flue gas containing only carbon dioxide, water vapour and small amounts other impurities. Oxyfuel combustion is superficially similar to combustion in air, but there are inevitable differences. This paper describes ignition tests on pulverised coal suspensions using a suite of coals of different rank and from different countries of origin and over a range of oxygen and coal concentrations of interest for oxyfuel combustion. The ignition tests were carried out using the National Institute for Occupational Safety and Health (NIOSH) 20-litre explosion chamber. The purpose was to determine how easily the various coals ignite and burn in mixtures of O2 and CO2 compared to their combustion in air. The residual char volatile and ash contents for the ignition residues were measured using a thermogravimetric analyser (TGA), allowing Q factors (i.e., enhancement in apparent volatile yield due to higher heating rates and/or heterogeneous reactions) to be determined and compared. An ignition index has been derived from the explosion and char data. This index has been used to rank low volatile coals for ignition propensity in air. The results show that to obtain ignition and combustion comparable to that in air, the oxyfuel O2-CO2 gas mixture must contain over 30% O2. Keywords: CO2 capture, combustion, pyrolysis, oxyfuel.

By Frank E. Cash

The data in this circular were compiled so that individual phosphate companies might have the benefit of the experience of other phosphate companies, and that industries in general might compare experiences (taking into consideration relative hazards), thereby promoting accident preven¬tion. ACKNOWLEDGMENTS The descriptive matter is taken in part from a. paper by Cash and von Bernewitz.4/ Production figures ore from Mineral Resources of the United States;5/ accident data were furnished by each of the operating companies in the pebble-phosphate district, and their assistance in making this report possible is gratefully acknowledged.

Jan 1, 1936

By D. Harrington

The record of fatalities from mine explosions in the United States during the past 44 years has been the best in the history of the mining industry, despite the fact that the number of fatalities from this cause during the past fiscal year now is nearly double that of the previous year. During there 4 fiscal years, mine explosions have resulted in an average of 45.5 deaths per year, compared with an average of 153 deaths per year for the preceding 5 years; an average of 542 deaths per year for the 3 years 1907-1909, inclusive, and a yearly average of 265 deaths per year for the 20 years prior to 1929. Other types of mine accidents also have been reduced during this period, but not to the same degree or by as large a percentage as mine explosions. The fact that in this fiscal year ended June 30, 1937, electricity was responsible for 60 percent of the explosions and 85.5 percent of the fatalities resulting therefrom (see tables 3 and 4) is evidence that either mine operators are lax in providing proper electrical equipment or there is laxity in the upkeep and use of electricity in our mines and more particularly in our coal mines. Several large coal-producing States that in the Fast have had numerous disastrous explosions have been free from such disasters for continuous periods of as long as 8 years. The bituminous mines of Pennsylvania, one of the largest coal-producing States, give a good example of what can be done to prevent explosions. 'his State, with its large number of operating mines, many with very definite hazards from gas or dust or both, has had only two major explosions (resulting in 16 fatalities) during the past 7 years; this is a decidedly good record compared with any similar period in the past and when it is considered that during this period about 750,000,000 tons of coal have been produced. Other good records are: Tennessee, without a single fatality from explosions during the past 9 years; Alabama, with 6 fatalities during the past 7 years; Illinois, with no explosions during the past 4 years; and

Jan 1, 1938

By L. C. IlsLey, M. W. Von Bernewitz

"Introduction.Several hundred thousand open lights are daily carried in coal mines of the United States, each lamp being a menace to life and property through fire or explosion. They have been responsible for many disasters in the past, and will be again. Flame safety lamps have been available for over a hundred years, but during the last ten years safe and practical electric lamps have been perfected. These have eliminated many of the flame safety lamps, and in a few mines have replaced open flame lamps. But there are still more than twice as many open lamps as electric lamps in our mines, and the open lamps should be discarded in favor of an approved type of electric lamp. There are several electric miners' lamps which have been approved by the Bureau of Mines for safety and efficiency, give good light, and are easily maintained and carried, some flame safety lamps will always be used, hut mostly for detecting gas; although they might be supplanted if some simple, reliable, and cheap gas detector were developed.Explosion Hazards from Open Lights.An open light and gas*** constitute a vicious hazard; while if there be coal dust present in the vicinity the consequences are multiplied many times. An open light and black blasting powder also constitute an explosion hazard, vividly attested by several serious disasters."

Jan 1, 1924

By R. A. Franks, G. F. Friel, J. C. Edwards, L. Yuan

Five mine fire experiments were conducted in a 2.08m high and 2.90m wide, ventilated mine entry in the National Institute for Occupational Safety and Health (NIOSH)'s Safety Research Coal Mine (SRCM) to determine the effect of the dispersion of carbon monoxide (CO) on mine fire detection. CO measurements were made at distances from 7.6 m to 45.2 m downwind from the fire with diffusion mode CO sensors positioned near the roof. For small intensity fires, less than 30 kW heat release rate, generated by 14 kg coal in a 0.61 m square tray, it was determined that air flow and sensor spacing were significant for fire detection at the 10 ppm CO alarm level. Within 15.0 m downwind distance from the fire, 10 ppm CO alarm values occurred for volumetric air flows less than 11.5 m3/s. However, the 10 ppm CO alarm value did not occur 30.0 m downwind from the fire for air quantities greater than 6.2 m3/s due to dilutive mixing of the CO in the air stream. The criterion that the mine fire alarms occur within 15 min of the onset of flaming combustion could not be consistently met with the 10 ppm CO alarm. This suggests the use of lower CO alarm values, or reduced CO sensor spacings for mine fire protection. It is demonstrated how computational fluid dynamics (CFD) can be used to model the CO dispersion downwind from the fire in support of a plan to optimize sensor spacings.

By Robert S. Sanford, Harold C. Pierce

"At one time the Alaskan Eskimo lived in many small settlements scattered along the Arctic coast. These settlements extended as far south as Bristol Bay and several miles inland on the large rivers. When the white man established trading posts, schools, hospitals, and missions, these people gradually congregated around them in a few large villages. The natural fuel supply near many of the large villages along the Arctic coast became exhausted as a result of the abnormally large influx of people from small outlying settlements.The population of Barrow, Alaska, according to the 1940 census, is 363 persons, but since that time it has increased considerably, and later estimates place the present population between 400 and 500 persons. With the exception of 25 white persons, the entire population is comprised of Eskimos.The government maintains a school, hospital, radio station, and weather station at Barrow. In addition to the government, installations, there is a church, a privately owned trading post, and cooperative store owned by the Eskimos.For many years the Barrow Eskimos depended on driftwood and petroleum residue from Cape Simpson for their fuel supply. This fuel provided not only warmth for the Eskimo during the long cold winters but also heat for melting ice, the only source of 'water during .the winter. In recent years the sources of petroleum residue and driftwood have not been adequate to meet the demands for fuel During the winter of 1942-43 and again in 1943-44, Barrow experienced an acute shortage of fuel.The fuel problem at Barrow was brought to the attention of Governor Ernest E. Gruening, who was instrumental in getting a Bureau of Mines engineer4/ to investigate reported coal occurrences in the vicinity. Coal deposits along the Meade River and at Peard Bay were examined during the spring and fall of 1943. The Alaska Native Service shipped in mining equipment in September 1943 and commenced stripping an open-pit mine on the Meade River in June 1944. In conjunction with this work, an engineer5/ of the Bureau explored by churn drilling to determine the tonnage of- coal in the vicinity of the mine. In addition to this work, the Bureau of mines examined coal deposits in Peard Bay area and along the Kuk River south of Wainwright."

Nov 1, 1924

By L. C. Brichta

The Canyon Diggings zinc-lead deposit is in an area of structural deformation of sedimentary rooks in Newton County, Mo., 14 miles southeast of Joplin, within the southern limits of the Tri-State district. Mining and milling on the several tracts covering the area had been carried on sporadically since 1900, and incomplete records show a production of 1,341 tonsof zinc and lead concentrates. On the northern part of the deposit the predominant metal is which occurs as galena, cerrusite, and pyromorphite in broken chert near the surface. On the southern part, lead is subordinate to zinc, which occurs mainly as carbonate and silicate minerals in brecciated chert to a maximum depth of about 150 feet. Analyses of samples from Bureau of Mines drilling indicate that approximately 77 percent of the zinc and 50 percent of trio lead i8 in nonsulfide minerals resulting from the oxidation of sphalerite and galena. Between August 12, 1948, and October 5, 1949, the Bureau of Mines investigated the deposit by churn drilling and sampling 85 holes aggregating 10,571 feet of bore and sampling two mill-tailings dumps and three mine dumps. Factual data on the investigation and the logs of Bureau of Mines drill holes are presented in this report.

Jan 1, 1950

By R. P. Walters, M. J. Lynch, D. R. Flinn

The Bureau of Mines evaluated tthhee feasibility of substituting platinum- coated metals for bulk platinum shapes as a means for conserving platinum . Platinum coatings were prepared using four different methods of electrodeposition , then tested and evaluated . In order for platinum coatings to be useful in process environments , they must be thick , adherent , stress - free , and pore - free . The Bureau evaluated direct - current , current reversal , cathode shielding , and pulsed- current plating techniques for producing a pore-free platinum electrodeposit from a molten cyanide bath . Aqueous corrosion tests of Fe - 10Cr substrates coated with approximately 25 μm of platinum showed that pulse plating yielded the most corrosion- resistant and , hence , the most pore -free coatings . The morphology of coating cross sections was in all cases columnar . The average grain size of pulse -plated deposits was independent of thickness , while all other plating techniques produced grains that increased in size as the coatings became thicker . It is believed that the constant grain size in the pulse - plated deposits resulted from better mass transport during the electrodeposition .

Jan 1, 1965

By W. L. Crentz

Knott County is one of the smaller coal-producing areas in the Eastern Kentucky coal field. It contains numerous coal beds, many too thin to support mining over a wide area, Coal produced in the county is from a few rail-shipping operations and many small truck mines. Many smaller mines are working beds whose exact location in the coal-bearing strata is uncertain. Samples were collected from 11 different coal beds, of which the Fire Clay, Hindman, Upper Elkhorn No. 3, and Flag are the most import ant from a product ion standpoint. Known reserves in the Hindman bed. are very limited, and almost the entire production from this bed is gathered from two comparatively, large rail-shipping mines in addition to the four principal beds, samples were taken in the Francis, Haddix, Fire Clay Rider, Whitesburg, Amburgy, Upper horn No. 2, and Upper Elkhorn No. I .beds. Figure 1 is a typical section of the strata, showing the more important coal beds and. readily identifying their location with respect to each other. The bed names as shown are particularly important because of the local tendency to assign several names to the same bed. To avoid confusion, the names by which each coal bed is known also are given in the following listing. The coal. beds., in descending order, follow: [ ]

Jan 1, 1953

By Christopher Van Dyke, Knox Van Dyke, Lixin Wu, Jaime Gutierrez

"I. INTRODUCTION(SILICA, THE LUNG, INFLAMMATION, AND FIBROSIS)Inhalation of respirable-size silica (0. I to 5 µm in diameter) deposits the particles in the deep spaces of the Jung where oxygen is exchanged. The resulting pattern of inflammation is substantially different compared to that observed from other inhaled substances such as carbon, polystyrene titanium dioxide etc. 1 Following the inflammatory reaction the body attempts to isolate the damage by walling off the area via fibrosis. 2 The unique nature of the inflammatory response to silica makes it logical to infer that fibrosis is a later-stage manifestation of the initial inflammatory damage. In addition to the inflammation extensive lysis and cellular death particularly to macrophages and neutrophils, can occur, depending on the dose of silica.' The ingestion of significant amounts of silica by macrophages and neutrophils produces an inflammatory sequence which activates the lipoxygenase pathway of arachidonic acid metabolism and produces platelet activating factor (PAF) and leukotrienes (LT).4·5II. CALCIUM IONOPHORE MIMICS SILICA TOXICITY IN VITROPhagocytic cells exposed to silica in vitro produce PAF and LT. This response is reminiscent of phagocytic cells exposed to the calcium ionophore (A23 l 87) in the presence of ionic calcium.6-8 A23 l 87 forms a complex with free ionic calcium which passes through cellular membranes, thus transporting calcium inside the cell. The increased intracellular calcium concentration triggers the production of small amounts of prostaglandins large amounts of LT. PAF and. depending on dose cellular death (see Figure 1 ). Could silica cause LT production and cellular death by a similar mechanism? How could silica - an inert solid - act in a similar fashion as a soluble stimulant? Clearly the negative SiO2 and OH- surface of silica can bind calcium ions9 and therefore could theoretically act as a solid-state ionophore releasing bound calcium inside of cells following phagocytosis."

Jan 1, 1998

By S. J. Pearce

"INTRODUCTION AND SUMMARYComplaints have been made regarding dust respirators that may be used in coal-mining operations. Some of these complaints may be due to improper use of the respirator, inadequate knowledge of its purpose and mode of functioning, poor choice, poor fitting, or inadequate maintenance. It is hoped that this circular will answer these complaints by discussing the various factors relating to the proper use of dust respirators in general and in coal mines in particular.It is pointed out that dust respirators are not to be used as a substitute for dust-control measures. The construction, functioning, choice, fitting, and maintenance of dust respirators are discussed.FIELD OF USEThe function of the dust respirator is to prevent the wearer from inhaling harmful quantities of dust by removing dust from the air he inhales.A dust respirator is not to be used as a permanent substitute for dust-control measures. It is to be used as a temporary substitute until dust-control measures can be instituted or as a protective means where dust-control measures are impracticable, as in applying rock dust in bituminous-coal mines.The following sections of the ""Federal Mine Safety Code for Bituminous-Coal and Lignite Mines in the United States"" 2/ emphasize the fact that every effort should be made to keep the amount of dust in the air of the working places as small as possible:"

Mar 1, 1950