Search Documents

By G. W. Birge, D. E. Wolfson, J. H. Lynch

This report by the Federal Bureau of Mines describes the carbonizing properties of coals from the principal beds in Boone County , W. Va . Results are given for samples of coals from No. 5 Block , Stockton - Lewiston , Coalburg , Winifrede , Chilton , Hernshaw , Cedar Grove , Alma , and No. 2 Gas beds . Boone County coals rank as high -volatile A bituminous . Eighteen of the 21 samples tested contained from 3.3 to 7.9 percent ash and 16 of the samples contained from 0.6 to 0.9 percent sulfur . Two samples from the Alma and No. 2 Gas beds , the lowest stratigraphically of the seams tested in Boone County , contained from 1.4 to 2.7 percent sulfur . Most Boone County coals yield

Jul 1, 1960

By Stephen C. Tadolini

The U.S. Bureau of Mines conducted a laboratory investigation designed to evaluate the stress and deformation characteristics of fully grouted roof bolts subjected to various magnitudes of end loadings. The experiment and subsequent analysis were completed, utilizing axial deformation data obtained -ultrasonically from forty-one 4-ft, grade 40 roof bolts, with a total of 132 measurement locations along the lengths of the bolts. The ultrasonic measurement instrumentation used in this investigation allowed for elongation measurements without requiring extensive bolt modifications. The results indicate that approximately 39 pct o{ the applied end load dissipated within the first 3.4 in of the bolts. However, only 3 pct of the applied load was realized beyond 28 in of the grout column. Data are presented individually for every 6-in increment of bolt length, and analysis was performed using statistical, nonlinear equations developed for 5,000 and 8,000 lb loading conditions.

Jan 1, 1990

Develop a method for mapping planar geologic features in deep underground mines where the presence of metal interferes with compass readings. Background A fundamental problem of mapping planar geologic features in deep underground mines is the presence of metal (water and air pipes, track, equipment, etc.), which affects the accuracy and consistency of compasses. Present geologic mapping methods include use of transits or theodolites, both of which are cumbersome and time consuming to use. To complicate the mapping, process each planar feature must be surveyed, and if that feature is not apparent on the opposite wall, it cannot be mapped. Another method of mapping is to stretch a tape measure between two survey spads and place a string along a planar feature on one wall and out into the opening until it intersects the tape measure. This method, in addition to being time consuming, is also inaccurate. Because detailed mapping of planar geologic features deep underground involves many repetitive measurements, a quick, accurate, and reliable method for making such measurements was necessary. The geolaser was developed to make such measurements in deep underground mines where metal interferes with conventionally used compasses.

Jan 1, 1990

By Sidney Katell

Several systems have been proposed for the production of synthetic crude oil from oil shale. An economic analysis of one proposed system is presented in this paper. An oil shale complex to produce 100,000 barrels per calendar day of semirefined crude oil will require a capital investment of $426,216,400. This investment includes mining, retorting, intermediate pipelining, and partial refining. A selling price of $3.74 per barrel of product will be necessary to maintain a discounted cash-flow rate of 12 percent.

Jan 1, 1971

By Anthony E. Szczuka

The purpose of this design note is to document the data that has been received from manufacturers, coal companies, training centers, government agencies, etc., that pertains to the completion of the Concept Feasibility Study For Training Equipment Designed to Improve Coal Productivity. Revision A documents additional data that has been received. ACKNOWLEDGEMENTS We wish to express our appreciation to the companies, mines, government agencies, unions, and contractor agencies listed herein that furnished the documented data. In most cases, it was furnished willingly and free of charge. In the few cases where the data was purchased, MDEC IRAD funds were used.

Jan 1, 1976

By E. G. King, W. W. Weller

Low- temperature heat capacity measurements of muscovite were made in the temperature range from 50° to 298 ° K. The entropy at 298.15 ° K was evaluated as S298.15 = 69.0 ± 0.7 cal /deg mole .

Jul 1, 1960

By S. J. Broderick

[The term "nonmetallic minerals? as commonly used is the mining industry, refers to those minerals of industrial importance that are mined essentially for uses other than for the metals contained. The field comprises several hundred rod minerals of industrial importance, of which 70 have can adequately described in the textbook Industrial Minerals and Rocks. A few o f the more important nonmetallic products are sand and gravel, salt, phosphates, clays, refractories, limestone, and cement materials. Some of the minerals, such as bauxite and pyrolusive, have both metallic and nonmetallic applications, but in this report only the nonmetallic mineral phases are considered. In the organic field of nonmetallics only coal is considered, as, the others - petroleum, natural gas, natural bitumens, and hydrocarbons - are of no importance in water softening.]

Jan 1, 1941

By Danny A. Riley, James R. Sanger, Hani S. Matloub, Michael Agresti, David Rowe, Lin-Ling Zhang, Yuhui Yan, Paula Galaviz, Judith Marchant-Hanson, Ji-Geng Yan

Until now there has been controversy about which tests should be performed to diagnose early Hand-Arm Vibration Syndrome (HAVS). Initial screening questions, especially about tingling and numbness, routinely given to patients prior to examinations proved to be a very important tool in the diagnostic process1, 4. However, standardized tests that are simple, quick, valid and reliable are needed to support a diagnosis of HAVS. Purpose: To find the most valid and reliable tests to diagnose HAVS. Material and Methods Five major tests were performed on Group I and Group II. Group I: Control group of 12 volunteers including students, nurses, secretaries and physicians with no history of using vibrating tools (age 20 to 50y, mean age 38.5y; 5male, 5 female.) Group II: 12 workers (age 17 to 65y, mean age 39y; 9 male, 3 female) were sent by a local trade union with a history of using vibrating power tools on their jobs for varying amounts of time (mean 12.2y, from 0.5 to 35y.) Pre-enrollment survey showed that each had more than 4 complaints commonly associated with use of vibrating tools (including numbness, tingling, weakness, pain, finger color or nail changes, temperature change, and difficulty moving.) 1. Sensory nerve conductive tests: Amplitude and nerve conductive velocity (NCV) were evaluated. 2. Cold Stress-Temperature recovery time tests were done on the index finger of the dominant hand following these steps: Confirm water bath is within 4-5º C. Place the finger temperature probe on pad of the index finger of the dominant hand. Record temperature every 15 seconds. Place subject’s hand in the cold- water bath for exactly five minutes. Record temperature every 15 seconds for ten minutes. 3. Blood test: Venous blood was taken by a 21-gauge needle with the yellow collection tube adapter. S-ICAM, Sera Thrombomodulin, Norepinephrine levels were evaluated by Henderson Research Centre, Canada. 4. Finger Sensory Evaluation: Semmes-Weinstein monofilament test and 2-point discrimination tests were performed on bilateral fingers. 5. Digital blood pressure test: blood pressure was measured in bilateral index fingers. Results 1. Median nerve sensory conductive amplitude from palm to wrist : GI: mean 96 ± 31µm; GII: mean 43± 30µm; for dominant hands. GI vs GII: P<0.001

Jan 6, 2006

By S. J. Broderick

[The term "nonmetallic minerals,? as commonly used in the mining industry, refers to those minerals of industrial importance that are mined essentially for uses other than for the metals contained. The field comprises several hundred minerals of industrial importance, of which 70 have been adequately described in the textbook Industrial Minerals and Rocks.3/ A few of the more important nonmetallic products are sand and gravel, salt, phosphates, clays, refractories, linestone, and cement materials. Some of tic minerals, such as bauxite and pyrolusite, have both metallic and nonmetal is applications, but in this report only the nonmetallic mineral phases are considered. In the organic field of nonraetallics only coal is considered, as, the, others - petroleum, natural gas, natural bitumens, and hydrocarbons - are of no importance in water softening.]

Jan 1, 1941

By Noel N. Moebs

The Bureau of Mines conducted five reconnaissance magnetometer traverses across a small abandoned chromite mine in the State Line district of Pennsylvania and Maryland to determine the geophysical response of the area. The results indicate that more extensive geophysical surveys of the region might establish some worthwhile guidelines for chromite exploration. While chromite only rarely can be detected directly by magnetic methods, there is a possibility that geophysical signatures in the adjacent host rock could provide some guidelines for further exploration. Prior to 1875, all the chromite produced in the United States came from the State Line district, and the potential for discovering additional podiform deposits could be significant. Virtually no state-of-the-art geuphysical or geochemical studies have been conducted in this district since World War II and sizable areas remain undeveloped and suitable for exploration. While the results reported in this paper are not supported by drilling, it may encourage others to investigate the area more fully for improved methods of detecting subsurface podiform chromite deposits. New theories on the emplacement of ophiolites also could contribute to an assessment of the chromite potential of the serpentinite belt.

Jan 1, 1991

By Thomas E. Lobb, Harry C. Verakis

Significant progress has been made in the reduction of serious injuries and fatalities resulting from mine blasting operations. Despite the progress, injuries and fatalities continue to occur. A leading cause of injuries and fatalities from blasting continues to be inadequate blast area security. Even though significant improvements in technology have been made, insuring adequate blast area security remains a challenge and requires constant vigilance. The advances in technology have created safer blasting products and have improved productivity and economics by enabling large, more efficient and effective blasts. However, as blasts grow larger in size, the complexity of adequately securing the blast area increases even more. Periodically the basic fundamentals involved in blasting safety should be reviewed, particularly for securing a blast site regardless of the size of the planned blast. Factors such as flyrock and toxic fumes must be taken into account to insure the safety of persons and property from the results of a blast. This paper examines the factors related to injuries due to inadequate blasting shelters and blast area security, and identifies mitigation techniques. The key concepts are: (a) accurate determination of the bounds of the blast area, (b) clearing employees from the blast area, (c) effective access control, (d) use of adequate blasting shelters, (e) efficient communications, and (f) training. Fundamentals are reviewed with an emphasis on analyzing task elements and identifying root causes for selected blasting accidents. Mitigating techniques are presented along with discussions and examples.

By Ronald S. Conti

This U.S. Bureau of Mines report discusses the results of research conducted in the Bureau&apos;s experimental mine at Lake Lynn Laboratory on the response of fire sensors to simulated mine fires, which included (1) a slowly developing coal-conveyor belt fire, (2) a rapidly burning liquid fuel-belt fire, and (3) a liquid fuel-belt fire in the presence of diesel exhaust. During these tests, several mine fire sensors were evaluated with respect to sensor placement, spacing, and type. The data indicate that smoke sensors alarm several minutes before CO sensors do; and that, in the presence of diesel exhaust, a prototype diesel-discriminating smoke sensor can successfully function without being sensitive to the diesel contaminants. The vertical placement of sensors in the entry near the fire was also shown to be critical in terms of alarm times. Additional data showed that variations exist in response time and level of response for two brands of electrochemical CO sensor. Results also indicate that early detection of fires will improve the probability of miners&apos; escape, because of reduced smoke concentrations during the incipient stages of the fire.

Jan 1, 2010

By Timothy J. Rohrbacher

This report presents results from an ongoing U.S. Bureau of Mines study defining domestic coal reserves. Examinations of five 7 ½ -minute central Appalachian quadrangles have been completed to date. Only 26.4%, 5.0%, 6.5%, 8.2%, and 4.2% at the coal resources remaining in the Matewan, Boltsfork, and Hoskinston, KY; Vansant, VA; and Beckley, WV quadrangles, respectively, constitute economically recoverable reserves. An evaluation of the coal mining industry&apos;s impact on the economy of Pike County, KY, wherein the Matewan quadrangle is located, was also completed in order to provide a basic understanding of the influence of coal mining on the local economy. Results show that coal mining is the only major income producing industry in Pike County, accounting for about 46% of the county&apos;s income, and 21% of the total available employment, in the base year 1990. If similar results are found in subsequent investigations, a strong argument can be made that traditional coal producing regions may soon be experiencing resource depletion problems far greater and much sooner than previously thought. This will affect not only the coal industry but, given the obvious dependence of Pike County&apos;s economy on its coal mining industry, the entire social and economic infrastructure of large areas.

Jan 1, 1994

By O. C. Blade

"INTRODUCTION This report on the properties of motor fuels sold through service stations in the United States is a continuation of a series of reports made in accordance with a cooperative agreement between, the Coordinating Fuel Research (C.F.R.) Committee of the Coordinating Research Council (C.R.C.) 3/ and the Bureau of Mines of the United States Department of the Interior. The first of these reports presented data on motor gasolines sold during the winter of 1935-36.-4/ Further reports have been issued describing motor gasolines sold during the succeeding summers and winters to the summer of 1941 and during the winter of 1942-43 and the summer of 1943 5/ No reports were made on motor gasolines sold during the winter of 1,) 41-42 and during the summer of 1942. The present report presents analytical data for 1,356 samples, representing the products of approximately 103 companies. As in previous surveys, the companies covered by the survey include both large and small suppliers. Conforming to former reports, the data cover three groups of samples - regular-price, premium-price, and third-grade gasolines - and each group has been averaged separately. The number of samples, items and brands comprising each group is as follows: Regular-price, 770 samples, 286 items, and 94 brands; premium-price, 537 samples, 236 items, and 72 brands; third-grade, 49 samples, 31 items, and 18 brands. The meanings of these terms as used in the surveys are as follows:"

May 1, 1944

By McHenry Mosier

This paper describes the practice in diamond drilling blast holes and discusses the relative merits of this method as compared with drilling by percussion rock-drills at eastern magnetite mine A. The rooke that were drilled included: (1) Gneiss; (2) sohist; (3) crystalline limestone; and (4) granular masses of magnetite. The principal stoping methods were: (1) Sublevel open stoping and (2) inclined room-and-pillar. Diamond drilling was used in the sublevel stopes and in some of the large pillars in an old section of the mine. Experimental work on diamond drilling blast holes began in 1943. Drill- ing proved difficult owing to the occurrence of fingers of extremely hard barren rock in the magnetite ore. All diamond drilling was contracted to a firm that furnished everything necessary for drilling except compressed air and water. In most instances the diamond-drill machine is clamped directly to a 3.5-inch column to reduce vibration. For drilling in floor pillars in open stopes, the drill was set on a demountable, sectionalized steel, frame with four legs carrying a 20-foot, 3.5-inch, extra-heavy pipe. "Both coring and noncoring bits were tried. In holes drilled with a cor- ing bit, the core was ground into sludge as the bit advanced so that it was unnecessary to delay drilling for pulling core. Data on tests with several types of bits are given as well as some oper- ating results. A direct comparison of costs between diamond drilling and percussion drilling was not available. The advantages of diamond drilling blast holes at mine A included: (1) Safer working conditions in open stopes. (2) The recovery of additional ore. (3) A reduction in the amount of stops development.

Dec 1, 1946

By Ernest W. Loya

A method for preparing gravimetric primary standards of helium in the parts per trillion range has been developed by the Bureau of Mines. The standards are used to calibrate a specially modified mass spectrometer used in determining the abundance of helium-3 and helium-4 in geochemical samples and of helium-3 in isotopically purified helium-4. The desired gas standards are prepared in 5-kg metal cylinders filled to 1,800 psia. Relative errors of less than 1 pct have been attained in the parts per trillion range using a successive dilution technique.

Jan 1, 1982

By H. W. Kilau

The Bureau of Mines tested chromium-bearing waste slags from industrial stainless steel and other chrome alloy operations to determine their chromium leachability characteristics under acid precipitation conditions and to devise measures to prevent any pollution originating from this source. Two critical slag composition factors were found to control the chromium leachability: (1) CaO:Si02 ratio and (2) magnesium content. Above a 2.0 CaO:Si02 ratio, chromium exists in slag as CaO·Cr203, which can be vulnerable to leaching by acid precipitation especially if oxi-dized to CaCr04 when exposed to the environment over an extended period. Maximum chromium leachability from industrial slags occurred when the composition of the slag had about a 2.0 CaO:Si02 ratio. Between a 1.0 and 2.0 CaO:Si02 ratio, in the presence of sufficient magnesium, MgO ·Cr203 was formed, which is very resistant to oxidation and to dissolution by simulated acid precipitation. Addition of magnesium silicates to molten slag to fix the chromium in the MgO·Cr203 form was successful in preventing chromium leaching in simulated acid rain solutions. Experiments showed olivine and waste taconite tailings were suitable for this purpose. Olivine addition to a waste slag having a composition vulnerable to leaching (CaO:Si02 > 2) reduced the chromium leachability more than 80 pct.

Jan 1, 1984

By W. J. Crawford, P. M. Gruzensky

"Several experiments have been carried out in efforts to evaluate qualitatively a variety of electrolytes for refining bismuth. Most extensive work was done with the basic tartrate, hydrochloric acid, and hydrofluosilicic acid electrolytes. Deposits that are smooth and adherent can be obtained from these three electrolytes if low cathode current densities are employed. All three electrolytes were effective in purifying crude bismuth considerably, with additional purification indicated in each instance by a reelectrolysis step.With the basic tartrate electrolyte best results were obtained when the electrolyte was at 40° C. and contained at least 100 grams of bismuth per liter. An apparent disadvantage was depletion of bismuth from this electrolyte, causing the deposits to become spongy and nonadherent.The hydrochloric acid electrolyte had the greatest tendency to yield rough, dendritic deposits. Best deposits were obtained at cathode-current densities below 2 amperes per square decimeter. A small amount of glycerin helped to produce a smoother deposit, and adding sulfuric acid or methyl sulfuric acid retarded the deposition of impurities. Very good results were obtained in electrowinning bismuth from a bismuth trichloride-hydrochloric acid electrolyte.Smooth and adherent deposits were obtained from a hydrofluosilicic acid electrolyte, with very good refining as regards lead and silver impurities; however, higher reagent costs and slow decomposition of the electrolyte have discouraged its use.INTRODUCTIONMethods of recovering bismuth from ores and byproducts were underdeveloped for many years because of the limited uses for bismuth, the pharmaceutical industry being the chief consumer. In the past decade or so additional uses for bismuth, particularly in the metallurgical field, have brought about increased demand for the metal with the result that bismuth is being recovered from byproducts that were once discarded. In addition to such uses as low-melting alloys, solders, bearings, die setting, etc., some interest has been indicated in bismuth as a possible coolant for nuclear reactors. The advent of ductile bismuth and bismuth-alloy thermocouple wire has contributed greatly to temperature measurement, particularly in the below-zero range."

Jan 1, 1956

By G. L. Oldright

The data in this paper were collected at the Trail smelter of the Consolidated Mining & Smelting Co. of Canada, Limited, through the courtesy of S. G. Blaylock, vice president and general manager; James Buchanan, smelter superintendent; George Murray, assistant smelter superintendent; and the staff members given in Paper XI, Report of Investigations 3243. INTRODUCTION This paper is the thirteenth of the series on Smelting in the Lead Blast Furnace, and the third of the series on Handling Zinciferous Charges. Tyro other papers have been written on the Rate of Descent of the Stock Column, and Formation of Accretions. These are Reports of Investigations 2963 and 3094, for the Tooele plant and the Bunker Hill plant, respectively.

Jan 1, 1934

By R. B. Ladoo

"Present Situation:At the beginning of 1920 a general feeling of optimism was noted in many talc-producing districts. The industry seems to have recovered from the temporary depression of the first half of 1919 and many mills are running at capacity production with their entire output for 1920 contracted for. The imports of talc for 1919 were only slightly larger than in 1918 by weight and probably no more by value. Thus foreign competition has not begun to be seriously felt. Several new companies in this country have been organized, some to operate new deposits and others to continue the work done by others.An interesting phase of the present situation is the possibility of increased use of talc in paint. There is a shortage of barium sulfate used as a paint filler. Since, for some uses, talc is considered second only to BaSo4 as a filler for paint, it is possible that part of the shortage could be relieved by an increased use of talc.A series of physical tests upon all pigment materials used in the manufacture of paints is being conducted for the Paint Manufacturers Association of the United States. It is important that all types of talc be represented in these tests. Producers of finely ground talc, 200 mesh and finer, are urged to submit samples of at least two pounds each of these grades that are available to paint makers with trade name and quality data, to the Institute of Industrial Research, 19th & B Streets, N. W., Washington, D. C., where the tests are being conducted."

Jan 1, 1920