Search Documents

By John H. Hild

The topography of the Jamestown fluorspar area is rough and ranges from 6,400 to 8,000 feet in altitude. Some fluorspar was mined as early as 1870, but mining really did not begin in earnest until 1940, and up to July 1947 it is estimated that 272,500 tons of fluorite was mined and milled. In 1947 the General Chemical Co. was mining fluorite and milling it in a 200-ton-a-day mill at Valmont, 7 miles east of Boulder, and the Ozark-Mahoning Co. was milling ore in a 100-ton-a-day mill at Jamestown, using ore mined, by H. M. Williamson & Son. These fluorite deposits comprise veins in a granite country rock. The Bureau of Mines drilled eight holes, aggregating 2,579.1 feet, on the Blue Jay vein; four holes, aggregating 1,434 feet, on the Chancellor; and one 350-foot hole on the Nations Treasure. Fluorite of a minable grade and width was found in 10 of the holes drilled. In this report the location and accessibility, physical, features and climate are described and a brief history of the district is given. The deposits and character of the ore and sampling and analyses are described, mine workings are outlined, and work performed by the Bureau of Mines is summarized. Diamond drill logs are shown in appendix I, and 'Sample analyses are tabulated in appendix II.

Jan 1, 1949

By T. R. Taubert, D. H. Carlson, J. H. Johnson

"ObjectiveDevelop a portable emissions measurement apparatus to sample and measure tailpipe concentrations of diesel particulate matter (DPM), carbon monoxide (CO), carbon dioxide (COJ, nitric oxide (NO), and nitrogen dioxide (NOJ under steady-state engine load and speed conditions during a 1-minute test.BackgroundThe U.S. Bureau of Mines (USBM) has a comprehensive research program to develop ways to reduce exposure of miners to diesel exhaust pollutants. Engine maintenance has been shown to have important effects on such exposure.Accurate measurements of tailpipe emissions are becoming an essential part of a good maintenance program for underground mines that use diesel-powered vehicles. Past studies of particulates in U.S. underground coal mines have shown that DPM alone may be present at concentrations greater than 1 milligram per cubic meter (mg/m3), half the 2-mg/m3 limit for respirable coal mine dust. A poorly tuned (smoking) diesel engine may be the sole cause for respirable dust concentrations exceeding the limit. Although there is currently no standard specifically for DPM in U.S. mines, regulatory steps are underway, and significant reductions of DPM levels in both coal and metal mines will most likely be required.Tailpipe emission measurements can provide diagnostic information to identify engine malfunctions such as clogged air cleaners, faulty injectors, or incorrect injection timing. In some cases, mine vehicle tailpipe DPM concentrations have been reduced up to 50 percent by engine maintenance and adjustments.An accurate measuring instrument would also be useful for determining the effects of exhaust control devices on tailpipe emissions. Little information is currently available about the overall effectiveness of exhaust controls after long-term use. Raw exhaust concentrations with and without the control device can be measured in underground mines, and from these data a control efficiency can be calculated. Knowledge of the effectiveness of exhaust control devices over time is needed to make intelligent decisions on bow to use and maintain these devices, and when to replace them."

Dec 1, 1995

By Martin Berman

Tables of 28 positions for all the transitions for nine common analyzing crystals for first, second, and third order reflections were compiled by the Bureau of Mines to facilitate elemental X-ray fluorescence analysis on multi-element systems. The tables are based on a compatible set of wavelengths for 2,346 observed X-ray transitions of the elements lithium to americium. The results are tabulated in order of increasing wavelength as well as by increasing wavelength for each element.

Jan 1, 1969

By W. E. Wallace, S. -G. Xing, M. J. Keane, J. C. Harrison

"SummaryDiesel-exhaust particles from two sources were dispersed in aqueous mixtures of dipalmitoyl phosphatidyl choline, a major component of pulmonary surfactant, and were tested for genotoxicity. Diesel samples from the same sources were extracted with dichloromethane and transferred into dimethyl sulfoxide and subjected to the same assays. Both types of extractions yielded similar results in both the Salmonella mutagenicity assay and the sister-chromatid exchange assay using V79 cells. After separation of the samples into supernatant and sediment fractions, the activity of both diesel samples was shown to reside exclusively in the supernatant fraction for the solvent-extracted samples, and exclusively in the sedimented fraction for surfactant dispersed samples. These findings indicate that genotoxic activity associated with diesel particles inhaled into the lung may be made bioavailable by virtue of the solubilization / dispersion properties of pulmonary surfactant components.While diesel engine emissions are associated primarily with transportation, they are also very common in the workplace. Estimates for the U.S. are that as many as 1.35 million workers in as many as 80 000 workplaces are exposed to the combustion products of diesel engines (NIOSH, 1988). These occupations include, but are not limited to mining, agriculture, motor vehicle maintenance, fork lift truck driving, truck driving, and tunnel and bridge operation."

Mar 1, 1992

By H. B. Humphrey, F. E. Cash

The following information on accidents in Alabama during 1930 was compiled from data obtained from the companies represented in a course on accident prevention given by the United States Bureau of Mines in Birmingham. These mines produced nearly three-quarters of the tonnage of that State for the year, and included most of the larger operations in the district. The figures are probably representative of the mines which are doing recognized safety work, and are better than the average for all the mines in Alabama. Table 1 lists the days lost in accordance with the weights given to fatalities and permanent disabilities, part and total, which is the scale used in the National Safety Com¬ petition for Mines, conducted by this bureau. By way of explanation, temporary disabilities are weighted according to actual number of calendar days of disability, including Sundays and holidays — that is, all days are counted except the day of accident and day of employee's ability to return to duty. Hernia is classed as a temporary disability to be charged with the actual number of calendar days during which the employee was unable to work. Table 2 gives the number of accidents and the days lost from each cause at 45 coal mines and 7 iron ore mines, also the average frequency and severity rates.

Aug 1, 1931

By Paul Hughes

This paper describes a focus of work presently being conducted at the Rock Mechanics Research Group at the University of British Columbia. The underhand method under consolidated fill ensures a high recovery under an engineered back that is comprised of cemented rock fill and/or cemented paste fill. This method of mining has been employed successfully in mines throughout North America as a method of mitigating exposure to the operator having to work under a seismically active ?back?. This paper reviews design methodology in the placement and analysis of sill mats with reference to site observation coupled with on going numerical and analytically derived solutions.

Jan 1, 2006

By Edward G. Cunney

[Track in underground bituminous coal mines was investigated and technology has taken from other industries in order to Main information on conditions that impair the safety and efficiency of the track and to develop guidelines ad useful information on the constriction, inspec¬tion and maintenance of mine track. Volume l contains information oil the investigations, observed track conditions, useful technology from railroads and other industries, derivations of track condition descriptors and limits, conclusions, and recommendations. Volume 2, Guidelines, contains recommended standards and practices for mine track. It includes the relation of track conditions to safe speeds; descriptions and limits for measurable track features such as gage, descriptions of conditions for track components that are normally not measurable, such as subbase soils; construction requirements and techniques; inspection requirements and methods; and methods for managing and performing track maintenance work. As a research product, it 0005 nut repeat the summary or derivations. Volume 5, Inspection Handbook, summarizes recommended standards and procedures from Volume 2 and provides related information for read: refer¬ence by inspectors in tin mines. As a research product to be used in mines, it does not repeat the summary, derivations or references.]

Jan 1, 1977

By Howard F. Carl

"INTRODUCTION Talc is a hydrous magnesium silicate mineral found throughout the world in deposits of economic importance. This mineral occurs in different physical forms and varying degrees of purity, both of which affect its ultimate commercial usage. Talc is used in finely ground condition by the ceramic, paint, paper, rubber, cosmetic, and other industries. Most domestic talc production is of this type. Talc also occurs, although much less frequently, in massive, fine-grained, fairly homogeneous bodies; the impure varieties are the familiar soapstones, and the purer form is frequently called ""steatite."" Because of certain properties, the purest grades of this massive variety have a monetary value about 20 times that of the ground talc.One desirable property of this massive talc is its amenability to accurate cutttng, machining, and working in many ways, similar to a hard wood or soft metal, and then firing without warping or appreciable shrinkage into a hard, refractory ceramic body. Consequently, shapes that cannot be formed conveniently by molding and pressing can be produced readily with ordinary machine tools. When talc is fired to about 1,100° C., it is converted to a ceramic body with certain very desirable physical properties. This fired material has a hardness and toughness frequently superior to steel. It is a refractory and an exceptionally good electrical insulator. When formed from a high-grade talc essentially free from iron, it has unusually low dielectric losees, even at very high frequencies."

Feb 1, 1945

By M. S. Seehra, R. S. Pandurangi

"INTRODUCTION Silica and kaolin (a layer aluminosilicate) are among the major constituents of most coal mine dusts.' Whereas kaolin is cytotoxic in vitro but nonfibrogenic in vivo in humans and experimental animals,2-4 the cytotoxic and fibrogenic potential of silica is rather well established.5 Wallace and co-workers 6-8 have studied the cytotoxic potentials of both native and surface-modified silica and kaolin and inferred that retoxification is slow in the case of occluded silica vis-à-vis native silica. Recent epide¬miological studies indicate that silica concentration alone in a mine dust, as determined by transmission IR spec¬troscopy (TIRS), does not correlate well with the pro¬gression of coal workers' pneumoconiosis. 9 This obser¬vation has led to the suggestions that silica particles occluded by clays such as kaolin may not be fibrogenic. This proposal requires accurate estimations of kaolin, silica, and occluded silica. The current method of silica analysis in a mine dust sample employs TIRS of the 797- cm -1 band of silica, although its accuracy, as well as that of x-ray diffraction studies, is no better than 25 % , even in a laboratory-generated dust.° In this paper we have employed the techniques of diffuse reflectance spectros¬copy (DRS) and photoacoustic spectroscopy (PAS), in conjunction with an FT-IR spectrometer, for the quan¬titative determination of silica in laboratory-generated silica-kaolin mixtures.One of the main advantages of DRS and PAS is that, in these techniques, problems arising from sample prep¬aration of the KBr-based disks used in TIRS are avoided. There are, however, several other considerations (e.g., particle size effects and saturation phenomenon) which complicate the use of DRS and PAS for quantitative work. 10-25 In this paper, we have carried out a systematic comparison of the quantitative abilities of the two tech¬niques, as applied to the silica-kaolin mixtures, with par¬ticular attention to the saturation behavior of several bands with different absorption coefficients. In particular, we show that a weaker band for silica at 1875 cm-1 is suitable for quantitative purposes, and that quantitative accuracy is higher in DRS than in PAS. Details of this work are given below."

Mar 1, 1992

By S. J. Rodgers

This report presents guidelines on methods of dust control in conventional coal mining operations. The normal mining cycle and equipment used in a room and pillar conventional section are described. Main ventilation, section ventilation and face ventilation are discussed in detail. Proper installation of line brattice, maintenance of proper air flows at the face and split ventilation are stressed. The effects of maintaining the end of the line brattice near the face are described. The advantages and disadvantages of blowing and exhausting face ventilation are presented. The use of water sprays on cutter bars and loading machines is described. The design of a nonclogging water spray system developed under a Bureau of Mines contract is presented. Other methods of reducing dust exposure are discussed and include alternative procedures for shot firing and administrative controls.

Jan 1, 1983

By J. R. Hoskins

A recent survey of 23 vein-type metal mining operations in several western states discloses that some of the more serious deficiencies in ventilation technology are associated with inordinately high levels of mine resistance. This problem has progressively increased over many years of operation (without adequate remedial action) as mines have become extended in depth. Where two shafts form the downcast and upcast airways of a relatively deep mine, the whole of the mine air volume must pass through each shaft in turn. Since at least one of these shafts contains hoisting equipment, structural members are necessary to support the rigid guides and shaft walls. These offer high aerodynamic resistance. In some deep mines, a single shaft of this nature may represent upwards of one-half of the total mine resistance. The second shaft, depending upon its design, may represent an additional one-third of the mine resistance. Therefore, the various working levels throughout the mine contribute only the small remaining amount of the total mine resistance.

Jan 1, 1972

By David C. Byrne

From an engineering perspective an ideal industrial noise control solution focuses directly on the actual source of the poise. Eliminating the noise-generating mechanism altogether obviates the need for other noise contra l treatments or hearing protection devices. However, in cases where attenuating the source is not feasible engineering controls must be oriented toward blocking the path that the sound waves travel toward employees. Acoustical enclosures are commonly used as sound path treatments to contain the noise from a machine: alternatively a control room/booth or equipment operator's cab may be used to isolate the worker from the noise. Anyone who has successfully used acoustical enclosures knows that the design procurement, and installation process is deceptively simple. Alt too often First-time efforts fait to account for many of the constraints that can render the enclosure essentially useless. Things that cannot be overlooked include: providing convenient worker access (physical and visual): allowing for proper machine operation/product flow; and supplying fresh air or preventing undue heat or contaminate build-up inside the enclosure. All of these factors must be given careful consideration, otherwise the enclosure will not perform adequately.

By G. R. Hopkins

"Refiners are generally considered solely as fuel producers, but actually they also comprise a group one of the largest consumers of fuel. For example, during the year 1929 the refineries-burned 51,544,000 barrels of oil as fuel, or the equivalent of over 5 per cent of the crude oil processed in that year. In addition enough other fuels - coal, natural gas, refinery or still gas, and petroleum coke - were utilized to raise the total fuel consumption based on B. t. u. equivalent to more than 10 per cent of the heat value in the total crude oil run to stills. Refineries utilize fuel chiefly as the heat-forming element distillation, but also under-boilers in the formation of steam used in refining, for the heating of buildings, and in the generation of electricity.In the early days of refining, the problem of fuel utilization and fuel economy was of scant importance to the refiners. Margins of profit were comparatively high and the major portion of the operatros1 attention was directed toward increasing their throughput. However, the keen competition that has prevailed in the refining industry over the past five years or more has taught the refiners that their expenses, one of the largest items of which is the cost of fuel, must be curtailed. Thus in 1925 the refiners used an average of 829,000 B. t. u. to refine a barrel of crude oil, wheras by 1929 this average had been reduced to 639,000 B. t. u., a decline of 23 per cent (see fig. 1)Since 1925 oil has ranked first as a refinery fuel (see fig. 2). The use of natural gas increased during 1926 and 1927 but declined in 1928 and 1929. On the other hand, the use of refinery gas has grown rapidly in importance. Coal has shown a steady decline in use at refineries since 1925. Petroleum coke has never supplied more than a very small fraction of the total fuel requirements, although there has been a steady increase in its use."

Sep 1, 1930

By J. C. Edwards

The Bureau of Mines developed a mathematical model for analysis of the impact of scrubber bed length, porosity, and gas flow rate on the absorption of C02 in a breathing apparatus. The model accounts for the decrease in available absorbent through chemical conversion. The pre-dicted efflux of C02 from a canister containing LiOR compared favorably with measured values reported elsewhere. It was determined from a com-putational study that the time for breakthrough of C02 at a prescribed level is nearly directly proportional to bed length and inversely pro-portional to gas flow and porosity.

Jan 1, 1987

By Phillip N. Yasnowsky

This Bureau of Mines publication tabulates State taxes levied on nonfuel minerals that have the characteristics of a severance tax.

Jan 1, 1978

By R. P. Beyer

Low-temperature heat capacities and standard enthalpy of formation of copper difluoride (CuF2) were determined by the Bureau of Mines. The low-temperature heat capacities were determined from 11 to 302 K by adiabatic calorimetry. The enthalpy of formation was determined by HC1 solution calorimetry. The standard values of entropy (S°) and enthalpy of formation (?Hf°) at 298.15 K are l8.65±0.03 cal/deg mole and -129.02±0.29 kcal/mole, respectively.

Jan 1, 1978

By Steven J. Page

Longwall double-drum shearers frequently have difficulty complying with the 2.0 mg/m3 dust standard and, therefore, require the use of effective dust controls. However, before dust controls can be implemented effectively, the major individual dust sources must be determined and their relative severity evaluated. The Bureau of Mines has recently developed a sampling strategy, based upon short-term gravimetric sampling, that can identify the major dust sources contributing to the shearer operator's exposure. This technique utilizes approved gravimetric sampling equipment already available to all mine operators and can be performed by two people in 2 days. Five examples, including data analysis, are discussed with respect to various cutting sequences. In addition, typical dust source contributions obtained from studies of double-drum shearer operations regularly in compliance are included. Mine operators can thereby compare their dust source evaluation results with those from these longwalls.

Jan 1, 1982

By George Bockosh

Mr. Bockosh is an electrical engineer with the U.S. Bureau of Mines In Pittsburgh, and has devoted the last two years to research on underground illumination. He formerly was a mine maintenance foreman and worked two years underground. He is a graduate of the University of Pittsburgh, where he is now working toward his masters degree in mining. When Congress first legislated light in American coal mines, it was a little like mandating a walk on the moon before the first satellite had been put in orbit. It was never a question, of course, of whether it could be done. But no one knew quite how. It's one thing to string a few light bulbs, and quite something else to provide uniform, sufficient, safe and reliable illumination, with fixtures that will hold up under some of the toughest conditions in the world - in the life-and-death circumstances of a craggy, black cavern filled with dangerous, moving machinery. In fact, in 1969 when Congress originally mandated illumination standards for the work places of underground coal mines, no one even knew just how much light was needed. That question was answered within a year by the National Bureau of Standards. In a study commissioned by the U.S. Bureau of Mines, the Bureau of Standards determined that underground mine should be illuminated with a light intensity of 0.06 foot-lamberts, a measurement of light reflected from surfaces in the lighted area-as opposed to foot-candles, a measurement of light from the source of illumination-in order for miners to adequately see what they are doing. That study was followed by more detailed research done at the Bureau of Mines' direction by the Research and Development Department of the Naval Ammunition Depot in Crane, Ind. This work evaluated the specific lighting needs of miners engaged In more than 100 different job tasks in all three types of coal mining- conventional, continuous and longwall. The Naval Depot report brought forth nearly 300 pages of detailed lighting data and concluded that proper illumination of mine work areas would serve more than just the cause of mine safety.

Jan 1, 1976

By Albert L. Toenges, Louis A. Turnbull, Henry E. Dekay, James N. Scudder

A preliminary survey of coke and steel plants conducted by the Bureau of Mines in cooperation with the Office of Solid Fuels Coordinator and under the auspices of the Coke Production Committee indicated that a very appreciable increase in pig-iron production would be obtained if pres- ent blast furnaces were supplied with a more uniform coke. Control of the sulfur and ash content of coal used for making coke is an important factor in producing uniform coke and thus increasing blast- furnace efficiency. In some mines producing metallurgical coal, the analysis of the coal bed shows a wide range of sulfur and ash content. To obtain production of coal with minimum deviation in sulfur content sampling, grading, selective mining, blending, and surface preparation are practiced at some mines with satisfactory results. The mines selected for this study have developed these methods and are successfully producing coal of uniform sulfur and ash content. The systems employed at different mines vary according to the physical character- istics of the coal bed, the manner of occurrence of impuritites in the coal, the development plan and mining system, surface preparation and the acceptable impurity content of the prepared coal. The ash content of the coal can be controlled by face preparation and in the cleaning plant. The introduction of some method or practice at other mines might make possible the use of coal for inetallurgical purposes that otherwise could not be used for making coke because of the wide variation of sulfur and ash content.

Dec 1, 1943

It is suggested in chapter 1 that emergency activities (including escape) are not individualistic. They tend to be group responses. If escapes from mine fires are group activities, then preparation for such events must take group behavior into account. This chapter explores the hypothesis that the miners who escaped from the three mines under study did so as members of groups. For development of this chapter, the database was examined for evidence of the existence of escape groups and for instances when individualistic behavior was paramount. Illustrations of group and/or individualistic behavior were analyzed and representative examples are provided in the following discussion. The nature of groups was discussed in chapter 3 and the following working definition was offered: "We mean by a group a number of persons who communicate with one another often over a span of time, and who are few enough so that each person is able to communicate with all the others, not at second-hand, through other people, but face-to-face" [Homans 1950]. To determine whether or not groups existed during the fire evacuations, it is important that the concept of group be clearly defined. Therefore, the discussion started in chapter 3 will be elaborated here. The defining characteristics of group given in chapter 3 were taken from Homans [1950]. They include size, person-to-person com¬munication, feelings that members have for each other, explicit and implicit rules for behavior, and common activities. An additional characteristic that is sometimes used to define groups is cohesiveness. Kiesler and Kiesler [1970] state, "Cohesiveness would include not only the attraction that the group holds for its members but also any other force operating on the individual to stay in the group." Variables said to contribute to cohesiveness include "(1) the attractiveness of a group for its members," and "(2) the coordination of the efforts of the members" [Keisler 1970]. One source of the attraction to a group occurs when "the goals or exterior tasks confronting the group are consistent with those of the individual person, and can best be handled by group action" [Cartwright and Zander 1968, in Davis 1969]. In other words, a common goal and a coordinated effort mounted to achieve that goal contributes toward the creation of a cohesive group. As discussed in the earlier review of research (chapter 1), groups have frequently been studied in laboratory or simulation settings. These methods allowed control over variables of interest. Kiesler and Kiesler [1970] state, however, that they "find group variables conceptually imprecise and experimentally difficult to work with." Experimental control, in other words, is difficult to achieve in the study of groups. The richness of the naturalistic mine fire data may provide an opportunity for an examination of groups that cannot be found in laboratories or simulations because this environment was not

Jan 1, 2000