Search Documents

By Allen D. Look

Uninterrupted shaft operations are an important economic factor in mine operation, and good shaft support is an important aid in preventing accidents and interruptions. More permanent supports can cut the hazards, costs, and delay incident to replacement of conventional timbers, especially where subject to decay. Installation of prestressed, precast concrete shaft supports in 100 feet of shaft at the Banner mine, Lordsburg, N. Mex., nave a satisfactory permanent installation in a section of shaft that had given trouble with conventional timbering. Use of rock bolts supporting gunited wire netting around the rock walls of the shaft prevented sloughing. No attempt was made in this paper to arrive at comparative costs of installation of various types of support. However, it was indicated that use of a lighter weight aggregate would be desirable in further use if prestressed precast members as placed in the Banner mine.

Jan 1, 1957

In 1991, the USBM (U. S. Bureau of Mines) evaluated the mineral resources of the 174,550-acre Bear Creek-Poker Peak area. Located 40 air miles east from Idaho Falls, ID, the study area is in the Caribou National Forest but is mostly administered by Targhee National Forest. USBM personnel mapped and sampled mines, prospects, and mineralized sites in and near the study area. Five types of mineral occurrences were identified in the study area: phosphate, limestone and travertine, placer gold, coal and uranium (the latter contained in the coal), and oil and gas. The study area has a high potential for oil and gas; evaluation of these commodities were beyond the scope of this study.

Jan 1, 1992

By A. W. Deurbrouck

This report describes the preparation characteristics of the significant coalbeds from which samples could be obtained in Webster County, W. Va. In 1964, approximately 825,000 tons of coal was produced in the county, of which 732,000 tons was mechanically cleaned in three preparation plants. The Sewell coal bed accounted for 94 percent of the coal produced. Twelve samples were collected from five coalbeds. Four of the samples would require upgrading to meet metallurgical requirements; two others of just over 8.0 percent ash would require some upgrading. In general the coalbed samples collected in the county were of medium-sulfur and medium-to low-ash content as received or after removal of the sink 1.58-specific-gravity material.

Jan 1, 1966

By Eric R. Bauer

This Bureau of Mines publication describes and illustrates the physical signs of excessive loading on mine roof supports, installations, and openings. It is designed to assist mine personnel in recognizing potentially hazardous ground conditions, by emphasizing the preliminary effects of developing unstable ground. Increased worker awareness can be expected to reduce the injuries and fatalities resulting from falls of roof, rib, and face.

Jan 1, 1985

By W. W. Adams

"Accidents at coal mines in the United States in September 1926 resulted in the loss of 170 lives, according to information furnished to the Bureau of Mines, Department of Commerce, by State mine inspectors. Of this number 125 occurred at bituminous mines and 45 in the anthracite field. As the bituminous output of coal for September was 48,976,000 tons, and the production of anthracite was 8,444,000 tons, the fatalities reported represented a death rate of 2.55 per million tons for bituminous mines and 5.33 for anthracite mines. The industry as a whole showed a fatality rate of 2.6 per million tons of coal produced in September 1925 the rate for bituminous coal mines was 3.29; the anthracite mines were idle in September last year due to a strike.During the first nine months of the present year 1,759 men have been killed by accidents at the coal mines throughout the United States, resulting in a death rate, per million tons of coal produced, of 3.76 as compared with 3.95 for the same period in 1925. Reports for bituminous mines alone showed a nine-month fatality rate of 3.53 which was about the same as the corresponding rate from January to September in 1925. The anthracite rate for the present year, however, shows a decrease of about 17 per cent; that is, the rate has declined from 6.36 to 5.28.Records covering the first nine months of 1926 show that 12 ""major"" disasters, that is, disasters in which five or more men were killed at one time, have resulted in the loss of 271 lives as against 10 disasters and 199 deaths in the corresponding months in 1925. The fatality rates for these disaster: alone were 0.579 and 0.465, respectively. One major explosion occurred at Tahona, Oklahoma, on September 3, 1926, in which 16 men lost their lives.An analysis of the principal causes of the 1,759 fatalities for the first nine months of the present year shows a reduction in the death rate as a whole and for falls of roof and coal and for explosives, but an increase in haulage, gas and dust explosions, and electricity. The comparative rates for these accidents were:"

Oct 1, 1926

By E. J. Schneider

In view of the current interest in the constituents of low-temperature tar, the Synthesis of three known xylenols and their hydroxyacetic acid derivatives has been undertaken by the U. S. Bureau of Mines. One of these xylenols, the 1,3,2 derivative first reported by Steinkopf and Höpner,4 has been described by Brown and Branting.5 The other two derivatives, the 1,3,5 first reported by Schütz6 and the 1,2,3 reported by Steinkopf and Höpner, have now been studied in greater detail. In the present work the synthesis of 1,2,3-xylenol and 1,3,5-xylenol was repeated, with some improvements in the former. The hydroxyacetic acid derivatives were also prepared, and it was found that while the melting point of the 1,2,3 derivative agreed with that of Steinkopf and Höpner. that of the 1,3,5 derivative was found to be 111° instead of 85 to 86° as reported by Schütz, by Steinkopf, and later by Bruckner. The discrepancy between the melting-point figures is doubtless due to differences in the purity of the xylenols used in the synthesis of the acids. Schütz obtained his 1,3,5 acid by recrystallizing an impure sample obtained from a mixture of xylenols. The difficulty of obtaining a pure acid by starting with a mixture is demonstrated by Bruckner, who despite painstaking efforts was unable to obtain the pure 162.5° melting 1,2,4 isomer from a mixture that persistently melted at 138° C. Steinkopf did not repeat Schütz's work but merely used the latter's figures in compiling a table. Bruckner, on the other hand. apparently also made the acid (by an improved method), and it is difficult to explain his checking Schütz's figure, unless it is that he, too used a symmetrical xylenol obtained from a tar and not prepared synthetically, as was the one reported in this paper.

Jan 1, 1929

By John Nagy, Austin R. Cooper

Information is presented on the pressure and rate of pressure development during a dust explosion . The data were obtained in laboratory studies in a 75- cubic inch vessel with mineral , agricultural and chemical dusts . The factors investigated include dust concentration , oxygen concentration of the atmosphere , admixed inert powder , and admixed moisture . Information is given also on the effects of these factors on the composition of the atmosphere after the explosion .

Jan 1, 1964

By F. J. Bailey

"In the fall of 1919, the U.S. Bureau of Mines began an inquiry as to the possibility of utilizing airplanes in conjunction with its rescue work, for quickly transporting engineers and oxygen rescue-apparatus to mine disasters.It was realised that this proposed use of airplanes has serious limitations, and if it were feasible, that the Bureau would have to rely on the cooperation of the established aviation fields of the U. S. Air Service for furnishing airplane service. Therefore Van. H. Manning, Director of the Bureau of Mines, under date of October 28, 1919, wrote the Director of Air Service outlining the rescue and first aid organization of the Bureau, the location of headquarters of district engineers, the distribution of safety cars and stations, and other essential details, and asking whether the Air Service could cooperate with the Bureau in the event of serious mine disasters. Major-General Charles T. Menoher, Director of Air Service, responded that the Air Service would be glad to cooperate insofar as possible, and designated those Air Service stations nearest the district engineers' headquarters, which might be best able to assist.The Bureau of Mines has ten mine rescue cars and eight mine safety stations distributed throughout the mining regions of the United States. The cars are each equipped with sets of oxygen mine-rescue breathing-apparatus and first-aid supplies. The car personnel consists of a mining engineer, surgeon, foreman, first-aid miner, clerk and cook. A foreman miner is in charge of each station and at five of the eight stations are mine safety trucks. The work of the cars and stations is two-fold; (1) Assisting in rescue and recovery work at mine disasters, and (2) training miners in mine rescue and first-aid methods, and in investigations looking to prevention of mine accidents. The country is divided into nine safety districts, with nine district engineers in charge."

Apr 1, 1920

By H. R. Shell

To obtain a better understanding of the crystallization of fluoride containing amphiboles from melts, an investigation of the range of stability between fluoramphi-boles and other minerals was conducted by the Bureau of Mines. This study has shown that the stability of fluoramphiboles is strongly influenced by both fluoride concentration and isomorphic replacement. Over 150 reactions were made with different compositions and reaction conditions. substitutions attempted and the phases that formed when the composition was crystallized by cooling from the melt are discussed. The attainment of equilibrium in these multicomponent systems is not claimed. Many ions that would be expected to enter the amphibole structure instead resulted in crystallization of phases other than amphibole. Those compositions that resulted in a high yield of acicular fluoramphibole by crystallization from the melts are shown in table 2. The fluoramphiboles obtained from melts typically had an acicular crystal habit and a hardness of 6 to 7 on the Mohs' scale. Although many had relatively high length to cross section ratios, none were fibrous; it was concluded that the possibility of synthesizing a fibrous fluoramphibole from a melt was low. However, many compositions can be crystallized into a tough, hard, impact-resistant mass of interlocking acicular crystals.

Jan 1, 1958

By S. H. Ash

THE INUNDATION of anthracite reserves in the Eastern Middle field of Pennsylvania affects the life of the anthracite industry in this field; it also influences the economic status of people, communities, and industries that depend wholly or in part upon anthracite for their livelihood. The trends of production and of employment in the anthracite-mining industry in this field are downward, and they probably will continue in this direction. The reserves have been depleted to the extent that the end of the active life of the industry as a. major economic factor is approaching. By removing the water in those pools where it can be done economically, the future of this industry may be extended somewhat.

Jan 1, 1950

By R. T. Johansen

A gradual decrease in injection rates commonly occurs as a water-flooding project becomes older. This decrease can be attributed to changes in reservoir conditions, such as swelling of clay minerals, fillup, or gradual plugging of the sand face. However, a rapid decrease in the rate of injection indicates abnormal behavior and is cause for alarm. Extreme plugging conditions can completely stop injections into a formation. Such behavior in wells was the main concern of the tests described in this report. An accepted method of alleviating this condition is by backflowing input wells - closing the supply lines to the wells and allowing the reservoir pressure to force water back into the wellbore and to the surface. If backflowing is not successful, a string of smaller diameter pipe sometimes is run inside the casing, and the sand face is flushed with a waterspray. More drastic treatment is to inject acid into the wellbore to dissolve extraneous matter, or even part of the reservoir material, in an attempt to restore the permeability of the sand immediately around the wellbore. Any of these procedures can he coordinated with bailing and swabbing of the well for cleanout purposes.

Jan 1, 1957

By Robert A. Jankowski

Through laboratory and underground studies, the Bureau of Mines has evaluated the use of passive barriers (dust shields) to help confine dust generated by longwall shearers to the face area. Laboratory studies focused first on selection of the optimum barrier design, which proved to be a simple, gobside barrier (made of conveyor belting), coupled with a headgate splitter arm, which was found necessary to prevent the dust cloud from entering the walkway at the headgate end of the shearer when cutting tail to head. Further laboratory testing was done to determine whether using passive barriers in combination with different water-spray dust-reduction methods, including the shearer-clearer system developed by the Bureau, would improve dust reduction over that from using the water sprays alone. It was found that the combination of gobs ide passive barriers plus the full shearer-clearer system was most effective, and surmised that this would be especially useful in thicker seams. However, underground testing revealed that the shearer-clearer system alone was 35 pct more effective in reducing dust contamination than when used with the gobside passive barriers, and far more effective than using passive barriers with a conventional water spray system. For such an effective system as the shearer-clearer; the reduction in avail-able space over the top of the machine actually impeded system performance; this was shom1 in both eastern and western mines. But when used with comparatively inefficient water spray systems, the passive barriers, used in combination with a headgate splitter arm, provide consider-able help in reducing dust levels in the walkway.

Jan 1, 1986

By Ernest A. Curth

The Bureau of Mines studied pressure changes in coal pillars by using encapsulated hydraulic pressure cells to measure relative changes in stress developed during mining. The data indicate that (1) abutment stresses were detected when the pillar line is within 42 to 100 feet, (2) vertical pressure increases as coal is mined in the pillars, (3) at first pressure is higher at the edge of the pillar than in the core, but as mining progresses, the higher pressure is measured in the core of the stump, and (4) in the two instances where lateral pressures were measured, they remained lower than the vertical pressures during pillar extraction. The data also indicate that the mean vertical pressure increase, 6P, in a pillar is roughly related to the percent of pillar extracted, A, by the empirical parabolic equation

Jan 1, 1967

By R. R. Sayers

The effect of comparatively low concentrations of carbon monoxide for short periods and under normal air conditions.of temperature and humidity , with the subject at rest , was studied by Dr. Yandell Henderson and his co -workers . In making recommendations to the New York and New Jersey tunnel commissions * he advised that , if the New York New Jersey vehicular tunnel be so ventilated that persons passing through the tunnel would be exposed to not more than 4 parts of carbon monoxide in 10,000 parts of air for not longer than 45 minutes , they would experience no ill effects . supplementary experiments , carried out by us in connection with our studies at the Bureau of Mines experiment station at Pittsburgh, substantiated this advice . ** In continuing our studies on low concentrations of carbon monoxide , we made a few experiments in a gas chamber where the conditions could be accurately controlled . The factors investigatel were : ( 1 ) The effect of long exposure in low concentrations of carbon monoxide ; ( 2 ) The effect of strenuous exercise ; ( 3 ) The effect of high temperature and humidity in low concentrations of ccarbon Lonoxide .

Mar 1, 1922

By Phillip Allender, Wolf Karo, Knox Van Dyke, Lixin Wu, Ali Ardekani, Jorge Garcia, Jaime Gutierrez

"We report that two different micropolystyrene round beads linked to either luminol or lucigenin have been developed. The 1-µ.m-diameter beads arc useful reagents that allow one to perform chemiluminescent (light producing) phagoeytic reactions without opsonization. It is known that luminol reacts with peroxidases (e.g., myeloperoxidase) while lucigenin reacts mainly with superoxide anion. Luminol and lucigenin beads produce cellular chemiluminescence (CL) with neutrophils, macrophages, monocytes, and differentiated human promyelocytic leukemic cells (HL60). When myeloperoxidase (MPO) is present luminol beads evoke higher CL from neutrophils, but when little or no MPO is present, lucigenin beads produce higher amounts of light. Lucigenin beads appear to be active inside these cells where unbound lucigenin does not enter freely.INTRODUCTIONA variety of cells, e.g., neutrophils (Ns) and macrophages (Ms), can engulf foreign particles (1). This engulfing or phagocytic activity is used by the body to kill bacteria and to eliminate foreign particles such as respirable dusts, e.g., coal, silica, or cotton. The neutrophil engulfs or phagocytizes bacteria which are coated with plasma antibodies and/or complement proteins (Fig. 1). The coating or opsonization allows the neutrophil to recognize foreign substances. Usually the absence of opsonization prevents the cell's recognition of a foreign particle and the particle is not phagocytized. Macrophages, particularly the alveolar Oung) cells, do not require opsonization for phagocytosis. Ms should not be selective toward individual dusts because they serve a major role in eliminating a variety of these.Particle size can also be a factor. Usually a particle with a diameter of 0.5-5 µ.m is considered in the respirable range. Larger particles are trapped before they reach the alveoli Oung spaces where oxygen exchange with blood occurs), ·and smaller particles do not generally settle, and are not engulfed by macrophages (2). Tabato and Ikada (3) found that maximal phagocytosis of microspheres takes place when their diameter is in the range of 1.0 to 2.0 µ.m. In addition, they found that beads with hydrophobic surfaces were more readily phagocytized than hydrophilic surfaces."

Jan 1, 1990

By Charles Vaught, Michael J. Brnich, Henry P. Cole, John V. Haley, William J. Wiehagen

Forty-eight workers who bad escaped large underground coal-mine fires were interviewed using an open-ended protocol. This information, and the actual experiences of one eight-person mine-section crew who escaped from a Fire, were used to construct an 18-frame (page) table-top simulation exercise, which was then field tested with 134 miners. The exercise is a research toot that measures miners' proficiency in the information-gathering and decision-making skills related to escaping from a mine fire. It also helps miners to learn and practice these cognitive skills. The exercise was found to be valid and reliable. All miners reported that the exercise was authentic and would help them to remember important information. The exercise total score, and all but two item scores, significantly discriminated among miners with different levels of training. The two items that did not discriminate dealt with whether or not to abandon a helpless fellow miner. When the exercise total score data were pooled, only 13.6% of the miners achieved a desirable score of 90% mastery or greater. The simulation is important because it teaches and assesses critical judgment and derision-making skills that are rarely addressed in miner training. Index Terms- Coal mining, critical skills, decision making, emergency escape and evacuation, escape from fire judgment training, mining, safety training, simulation training, under-ground mine fires.

By E. D. Gardner

"Trolley lines used in connection with electric haulage in mines are a source of danger and many lives have been lost by men accidentally coming in contact with the wires. Usually the wires in metal mines are sufficiently guarded to prevent men from touching them with their person or by pieces of steel which they may be carrying or their shoulders, while walking along the level. However, it is difficult to guard effectively the wires at loading chutes along the haulage ways and in spite of safe guards, chute tappers have been electrocuted through loading bars accidentally touching the trolley line.To overcome this danger the Calumet & Arizona Mining Co., at Lowell, Arizona formely used a hinged V-shaped trough made of 1-inch by 6-inch lumber, that was dropped over the wire in front of the chute, when the cars were being loaded. This arrangement interfered with the easy operation of the chute, and a cut-out device for the trolley line was devised by W. R. Gibson, chief electrician for the company. This cut-out is efficient easily constructed and roes not interfere with the operations at the chutes or with the motors operating on the same level.When the cut-out is open the electric current is carried past the gap by an insulated wire on the opposite side of the drift. A hinged board drops down over the ends of the trolley guard when the slide is open and Prevents anything touching the live wires. About ninety of these cut-outs are now in use in the mine,The levels under the scopes are timbered with drift sets placed 5 feet apart, and the loading chutes take up the space between two sets. All trolley wires in. the company's mines are carried 6 feet above the rails and guarded by two 1/2 by 6-inch boards placed on either side of the wire."

May 1, 1921

By William D. Monaghan, Michael A. Trevits

Over the period 2000 to 2003, roof falls have accounted for 4 to 14% of the fatalities in underground mining operations. The National Institute for Occupational Safety and Health (NIOSH) is conducting research to reduce the frequency, exposure, and risk of these events through an ongoing program of field and laboratory studies. One area of research involves the evaluation of polyurethane grouting technology that is commonly used to stabilize fractured mine roof strata. Concurrently, NIOSH is conducting work to evaluate the application of ground penetrating radar for advanced delineation of problematic mining areas. In this study, NIOSH partnered with Sub-Technical, Inc. who injected a polyurethane grout (also known as glue) into a roof area of NIOSH’s Safety Research Coal Mine. The mine roof area was scanned using ground penetrating radar technology before and after grout injection in an attempt to determine the extent of grout infiltration. A comparison of the pre-and post-grouting radar records showed a significant change at a mine roof depth of about four to five feet. The interpreted radar records were then compared with drill core information, borescope evaluation of roof-bolt holes in the study area, and underground observations. At this site, the interpretations of the radar records correlated with data obtained from the core holes, borescope evaluations and underground observations. This study showed that ground penetrating radar technology can be a useful tool for detecting changes in mine roof due to the injection of the grout.

By D. L. Paulson

The Bureau of Mines used 50-and 800-kva electric-arc furnaces to confirm the feasibility of producing ferronickel in electric-arc furnaces from pre-reduced concentrate from the Yugoslavian FENI project. The relationships were established among metallic iron concentrations (degrees of prereduction), ferronickel grades, and nickel recoveries. Smelting the concentrate containing 1.27 wt-pct nickel and metallic iron levels between 2 and 3 wt-pct, produced 15 to 20 pct ferronickel. Higher or lower metallic iron concentrations were compensated by adding oxide pellets or carbon to the electric-arc furnace charge. Over 90 pct of the contained nickel was recovered when up to 20 pct ferronickel was being produced. Data obtained while smelting 16 tons of prereduced concentrate in the 800-kva electric-arc furnace indicated ferronickel can be recovered at an energy consumption of 530 kwhr/ton of prereduced material.

Jan 1, 1977

By Tuncel M. Yegulalp

This final report contains the results of all work performed under BOM Grant J0333905. A preliminary systems analysis of coarse-particle coal slurry pipelines as a haulage method for longwall mining systems was performed. Two exhaustive literature surveys on state-of-the-art longwall mining and slurry transport technologies were prepared. Two representative longwall systems were designed, one with conventional haulage and one with slurry haulage. These two systems were then compared on the bases of cost, safety, and reliability. The conclusions were that for the case of a two-face longwall mine, a coarse slurry transport system does not have a clear-cut cost advantage over a conventional (conveyor-hoist) system. However, indications were that a cost advantage could occur under different analytical conditions such as: (1) a larger scale mine, (2) if intangible benefits were quantified, and (3) if new generation technology rather than currently available technology were applied to the study. Budget and time constraints prevented exploration of these conditions.

Jan 1, 1982