Search Documents

To provide a flexible, low-maintenance, low-cost continuous mine air monitoring system as an alternative to conventional fixed-point, electronic monitoring systems. Background Continuous monitoring of mine air is highly desirable (and often required) not only to improve miner safety, but also to increase mine productivity. Continuous air monitoring systems can provide earl" warning of developing fires, excessive methane accumulation, reduced oxygen levels, and other developing problems in remote, inaccessible or sealed areas, and in active workings. Fixed-point, electronic systems require one Sensor for every gas to be measured at every defined monitoring location. As the number of monitoring locations increases, so does the cost, along with increases in the time required for routine maintenance and calibration of the sensor System cost also increases when monitoring locations are identified for mine areas requiring permissible electrical equipment.

Jan 1, 1988

By Rudolf E. Greuer

Two computer programs for the real-time calculation of concentration distributions in the ventilation system of underground mines were designed. They allow one to simulate the movement of fumes or other contaminants with the ventilating air, the calculation of concentrations at any given point and time, and the determination of the total contaminant exposure at different places in the mine. Multiple and time variable contaminant sources can be handled and recirculation is no obstacle. The, first program is based on an airflow distribution which has, in the input data, to be stated. The second program has been linked to in existing program for the calculation of airflow distributions. Two versions of this second program are provided to accommodate the two existing programs. Several executed examples demonstrate the program performance.

Jan 1, 1981

By H. H. Schrenk

[A colorimetric method5/ for the determination of benzene in amounts as low as 0.001 mg has been developed recently at the U.S. Bureau of Mines Pittsburgh Experiment Station by the authors, with the assistance of chemical personnel fro a the Allegheny County (Pa.) Relief Works Division. The method is based on the direct nitration of either liquid - or gas - phase benzene, followed by neutralization, extraction with butanone, and final treatment with sodium hydroxide which produces a violet color. The color is matched with color standards of known values. Although the method is adaptable to many conditions the primary objective was a procedure that would be suitable for hygienic investigations. The development worth included a study of possible interference by chemicals that be present in those situations in which the method. would be employed. In this study it was found that a specimen of hexane prepared by the Gulf Research Laboratory, Pittsburgh, by fractionation of West Virginia natural gas gave positive result for benzene, whereas a specimen of pentane prepared in the same manner showed only a trace, and specimens of n -heptane and octane (2,2,4 trimethylpentane) supplied by Eastman Kodak Co. save a negative result. According to information obtained from the Eastman Kodak Co. the latter two compounds were highly purified, the n-heptene being prepared from line and the octane synthesized in the laboratory. On nitration of a larger amount of tae natural hexane a visible quantity, of needlelike crystals which resembled those of m-dinitrobenzene was obtained. The hexane from this nitration was recovered by distillation and again nitrated, but no crystals or colorimetric indication of benzene was obtained. This imitated that the specimen of natural hexane contained a substance which at least had the chemical behavior of benzene.]

Jan 1, 1935

Provide mine personnel with a convenient means of determining the optimum installation geometry of roof trusses in bedded roof. Background Mine operators frequently ask the following questions concerning roof truss installations: 1. Where should the bearing plates or brackets be placed or where should the inclined holes be started? 2. At what angle should the holes for the inclined chords or angle holts be drilled? 3. What tension should be put into the inclined chords so as to achieve the most effective results for the effort and expense? Truss hardware manufacturers have responded to these questions with answers based on what seems to work best. While designs based on past experience are frequently reliable, there was a need for a rational approach that could accommodate a variety of conditions. The Bureau has developed a procedure that enables mine operators to optimize roof truss installations in bedded roof.

Jan 1, 1989

By R. Barany

The heats of formation of anhydrous ferric sulfate and anhydrous indium sulfate were determined by solution calorimetry. At 298.15° K the heats of formation from the metal, rhombic sulfur, and oxygen were -615.6 ±O.7 kcal/mole for ferric sulfate and -649.6 ±O.6 kcal/mole for indium sulfate. Heats of decomposition at 298.15° K are given for the reaction that forms metal oxide, sulfur dioxide, and oxygen) and for the reaction that forms the metal oxide and sulfur trioxide.

Jan 1, 1965

By Gerald T. Homce, James C. Cawley

Electrical arcing injuries are the most common form of electrical injury in mining. MSHA data show that 381 "non-contact electric arc burn" injuries occurred in the mining industry from 1996 - 2005. A more detailed study of data from 1990-2001 showed that five types of apparatus - circuit breakers, conductors, nonpowered hand tools, electrical meters and test leads, and connectors and plugs were involved in two-thirds of the lost workday injuries. Many of the protections from electrical arcing injury available to workers in other industries stem from the application of National Fire Protection Association Standard 70E - Standard for Electrical Safety in the Workplace (NFPA 70E). NFPA 70E is a generally accepted industry guideline document, but excludes underground mining from its scope. Many of its practices and procedures, however, can be applied in the mining workplace to supplement the existing electrical safety requirements of Title 30 Code of Federal Regulations. This paper describes how NFPA 70E can be applied to mining workplaces after an analysis of the mine power system electrical arcing hazards has been completed (and Hazard/Risk Categories determined) using the tables from NFPA 70E or the calculation method as described in IEEE 1584. NFPA 70E can then be used to determine the levels and types of personal protective equipment (PPE) needed to protect miners against burn injuries. Appropriate lockout and tagout (LOTO) procedures for use in the mining industry are also described. Suggestions for better selection of electrically-rated hand tools are included. Recommendations for electrical meter selection and use based on transient withstand capability are also discussed.

By R. A. Kearns

Biennially the Bureau of Mines issues a list of equipment that has been accepted as approved or permissible during the two calendar years immediately preceding the date of publication of the listing. By so doing the mining industry is kept informed of the availability of the latest equipment for safe use underground. This list supplements Bulletin 543, Permissible Mine Equipment Approved to January 1, 1953; Information Circular 7722, Permissible Mine Equipment Approved During the Calendar Years 1953-54; Information Circular 7840, Permissible Mine Equipment Approved During the Calendar Years 1955-56; and Information Circular 7957, Permissible Mine Equipment Approved During 1957-58. This list includes equipment meeting those standards that have been revised since Information Circular 7957 was .issued. Schedule 16E,4 a revision of Schedule 160, was approved May 19, 1960.

Jan 1, 1961

Reduce the dust exposure of workers in large processing buildings at mineral processing operations, using a total mill ventilation system.

Jan 1, 1994

By C. L. Brown

"INTRODUCTION The heavy loss of life from mine fires in some coal mines recently has focused attention on the importance of maintaining reliable communication systems between the active working sections of mines and the surface. A study of conditions following disasters in mines indicates that in several instances lives could have been saved if telephone communication had been available. Communication systems were not installed in some of these mines where disasters occurred, and in other mines they were installed in such a manner as to be rendered useless following a mine explosion or fire. Lives have been lost because of the inability of the rescue crews or persons di-recting the rescue to communicate with trapped men. Cases are known where many lives might have been saved had it been possible to give instructions for escaping or for location of barricades.More than 500 major disasters in which 5 or more lives have been lost have occurred in mines in the United States. The total number of lives lost in these disasters has exceeded 13,000. Some of the victims died instantly; but for many it was hours and in some instances days before death occurred. Evidence found in recovery operations following some of the disasters indi¬cates that many died needlessly because of the lack of suitable means of communication between the underground working areas and the surface.A localized gas and dust explosion in a coal mine in 1930 resulted in the death of 82 men; 2 were killed outright by the force of the explosion, 6 by a combination of burns and afterdamp, and 74 by afterdamp. About 140 men escaped or were rescued following the explosion, Of these, 119 escaped with little or no assistance, 2 were rescued promptly following the explosion, and 19 were rescued from behind a barricade. Seven bodies were re-covered from behind an ineffective barricade in another place; subsequent investigation proved that these men might have been guided to a safe location had an effective communication system been available."

Oct 1, 1946

This chapter presents an overview of fatal and nonfatal injuries reported to MSHA during 1986-1995. Reportable injuries follow the criteria for reporting specified in 30 CFR 50. These criteria are listed in appendix A. The data used for these analyses came from the MSHA accident, injury, and illness data closeout files for the years 1986-1995. The MSHA data are described in appendix A and methods used in data analysis in appendix B. There may be slight discrepancies between the figures presented here and other presentations of MSHA data for the following reasons: (1) injuries to nonemployees have been excluded from analysis; and (2) injuries identified by MSHA after the files were closed out are not included. Within the MSHA data, there are differences in reporting requirements for operators and contractors. Contractors are required to report only those injuries that occur during certain categories of work (described in appendix A). For this reason, data on injuries among employees of operators and contractors in the MSHA database should not be considered directly comparable. As discussed in the "Introduction," the MSHA data on fatal injuries differ from the CFOI data (chapter 1) because of varying definitions used for the mining industry. As compared to the CFOI data, MSHA data exclude injuries that occurred off of mine property and include injuries occurring at mills and processing plants on mine property. Tables 4-1 through 4-9 and figure 4-1 provide comparisons of injury frequencies and rates among the commodities. These comparisons are followed by sections 4A through 4E, which provide more detailed tables and figures for each commodity separately. The method used to calculate injury rates is described in appendix B. Since denominator data for occupations (lob titles) were available for 1986 only, estimates of rates by occupation for the entire 10 year period are based on extrapolation from 1986 data. For this reason, estimates of injury by occupation should be interpreted with caution. Fatal Injuries A total of 1,078 fatal on-the-job injuries were reported to MSHA during the 10-year period 1986- 1995. The average annual fatal injury rate for all commodities combined during this period was 30.9 per 100,000 full-time equivalent workers. Mine operators accounted for 908 (84%) of the fatalities and had an average annual fatal injury rate of 28.2 per 100,000. While mine contractors comprised only 16% (n = 170) of the total number of fatalities, their average annual fatal injury rate was 2.3 times higher than that of mine operators (65.0 per 100,000). Table 4-1 presents the number and rates of fatal injuries by commodity for operators and contractors. Contractors in metal, nonmetal, stone, and sand and gravel are grouped together, since MSHA data on employment were not available for rate calculations for these commodities separately. The highest average annual fatality rate for the period, 66.5 per 100,000, occurred among metal and nonmetallic mineral mining contractors, followed closely by coal contractors (63.1 per 100,000). Among mine operators, the highest average annual fatal injury rate was in coal (38.9 per 100,000); the lowest was in nonmetal (14.3 per 100,000). Table 4-2 shows the average annual fatal injury rate by type of operation for each commodity for mine operators only. Of commodities with underground mines, all except stone had higher fatality rates at underground than at surface operations of these mines. The highest fatality rate for any operation occurred in surface operations at underground stone mines (124.5 fatal injuries per 100,000 workers). Stone had the second highest fatality rate for underground operations at underground mines (77.9 per 100,000). The highest rate for underground operations at underground mines occurred in metal (87.6 per 100,000). Table 4-3 shows the number and rate of fatal injuries by U.S. Bureau of the Census occupational groups (described in appendix D) for the 10 occupation-commodity groups with the highest fatal injury rates. These data should be interpreted with caution because the denominator used in calculating the rates was based on an extrapolation from data for the year 1986 only, as described in appendix B. Extractive occupations are represented in this group for three commodities: coal, metal, and sand and gravel. Construction trades are included for coal, sand and gravel, and nonmetal. The distribution of fatal injuries by commodity and work activity for mine operators is presented in table 4-4. A description of the work activity categories is in appendix C. Overall, the leading work activity at the time of injury was using or operating tools and machinery (26.4%) followed by constructing, repairing, and cleaning (24.0%), vehicular operations (18.8%), and materials handling (12.6%). The distribution varied by commodity. The largest percentage of fatal injuries occurred while operating tools and machinery in both coal and stone; during vehicular operations in metal; and during constructing, repairing, and cleaning activities in nonmetal and sand and gravel. Table 4-5 shows the distribution of fatal injuries by commodity and MSHA accident classification for mine operators. A description of the MSHA accident classifications appears in appendix E. The largest proportion of injuries overall occurred during powered haulage (28.5%). The

Jan 5, 2000

By E. C. Lane

[This Is the ninth in a series of reports on properties of commercial motor fuels, made in accordance with a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of Mines of the United States Department of the interior. The first report gave data on motor gasoline sold during the winter of 1935-36.3/ The Present report presents analytical data for 2,033 samples, representing the products of approximately 80 companies, which, as in previous surveys, include both large and small suppliers. In addition, the Pacific coast is represented by data that were average by the Pacific Coast Technical Group before 'being submitted and are published exactly as they were received. As in previous surveys, the data are divided into the three groups of samples of regular-price, premium-price, and third-grade gasolines, and each group has been averaged separately. The cumber of samples, items, and brands comprising each group, exclusive of those of the Pacific coast, arc as follows: Regular price, 1,066 samples, 208 items, and 49 brands; premium price, 575 tamales, 154 items, and 38 brands; third-grade gasoline, 7;4 samples, 150 items, and 53 brands. The meanings of these terms as used in the surveys tar as follows: Sample: The individual supply of gasoline obtained at the filling station and analysed in the laboratory.]

Jan 1, 1940

[ ]

Jan 1, 2008

By R. H. Lien

The Bureau of Mines investigated a roast-leach process for recovering a marketable lithium product from a montmorillonite-type clay deposit located on the Nevada-Oregon border. The clay sample treated in the investigation contained 0.6 wt pct Li. The lithium recovery process consisted of several unit operations. The lithium silicate compounds in the clay were converted to Li2SO4 by roasting a pelletized mixture of clay, limestone, and gypsum at 900° C in a direct-gas-fired rotary roaster. Water--leaching the calcine at 40 pct solids extracted the Li2SO4. Lithium recovery from the leach solution involved concentrating the solution by evaporation, adding Na2CO3 to the concentrated solution to precipitate Li2CO3 , and filtering the slurry to obtain the product. The product filtrate was recycled to the evaporator following a crystallization step. About 80 pct of the lithium in the clay was recovered as 99-pct-pure Li2CO3. Process operating costs were estimated at $2.12/lb Li2CO3 produced; the current Li2CO3 selling price is $1.48/lb. Raw materials. accounted for 30 pct of the total operating cost.

Jan 1, 1985

By J. C. Franklin

The Spokane Mining Research Center of the Federal Bureau of Mines is placing major emphasis on chemical stabilization as part of the ground support program. Development of polymeric material suitable for bonding rock fractures around the mine opening is one phase of the program. Some of the problems that must be considered are viscosity, applicability, adhesion, cure times, strength, toxicity, and flammability. Epoxies and polyesters were investigated, but shrinkage in polyesters caused redirected effort toward epoxies. Test results with the latter showed that bonded fractures in mine-roof strata were stronger than the virgin rock. Further tests showed that polymeric materials have good potential for bonding, and in conjunction with polymer roof bolts, are expected to result in an economic and useful new support concept.

Jan 1, 1974

By Gerald H. Groenewold

Reclamation of surface-mined landscapes is commonly defined only in terms of biological productivity. Other critical concerns associated with surface mining include the long-term quality of groundwater and stability of the postmining landscape. Meaningful reclamation design must address all these concerns. Reconnaissance of postmining landscapes indicates that three types of instability occur in these settings. These include: area-wide settling, localized collapse, and piping. Area-wide settling is most pronounced during the first year after contouring but appears in precontouring valley areas where frozen materials are contoured with a dozer. Although severe in some settings, development typically ends within one year. Piping appears to be a severe and long-term problem in some settings. Piping usually begins soon after contouring ceases and may continue for several years. In some postmining landscapes, piping has only started to develop after as many as five years of apparent stability. Piping is controlled by a combination of physical and chemical conditions in the spoil. A key factor is the presence of highly dispersive materials in the near surface. The design of a stable postmining landscape requires the integration of severe critical factors. These include: 1) detailed knowledge of the distribution of overburden materials with emphasis upon the delineation of highly sodic sediments; 2) proper equipment selection; and 3) a consideration of climatic factors. For reclamation to be successful, it must consider the entire landscape, not merely the soil zone. Any approach short of this will lead, at best, to temporary solutions.

Jan 1, 1980

By C. E. Julihn, Lowell B. Moon

"INTRODUCTION To increase the supply of ore needed to produce steel the Bureau of Mines has explored 187 mineral deposits containing chromium, iron, manganese, cobalt, nickel, fluorspar, tungsten, vanadium, or coal during the fiscal years. 1940-44, the deposits thus explored were selected from several thousand that were first examined to appraise their possibilities. The objective of the exploration was to determine the tonnage and grade of ores upon which mining, operations might be based, and the metallurgical processing that was most suitable for their utilization.Most of these deposits were sub-marginal by pre-war standards; hence there had been no incentive for their exploration, yet many such deposits were known to exist that probably contained ore sufficient in grade and amount to be utilized as war reserves.Some of the Bureau's exploration projects have disclosed substantial or even very large amounts of ore, much of which is fairly high in grade. In a few of them bodies of high-grade ore have been found, though in others the tonnage has proved to be too small or too low-grade for utilization."

Mar 1, 1945

By Albert W. Deurbrouck

This report describes the preparation characteristics of 23 coal samples collected from nine of the more significant coalbeds of Fayette County, W. Va. In 1963 almost 5.4 million tons of medium to high volatile B coals of excellent quality for metallurgical and steam markets were produced in Fayette County. Of the 23 coal samples collected 11 would require some upgrading to pro-vide metallurgical quality products, 11 were acceptable as received, and 1 was a noncaking coal. Cleaning these coals to metallurgical standards would require only the removal of the sink 1.58 specific gravity material which would be quite easy as very little near-separating-gravity material was present at this gravity.

Jan 1, 1965

By D. S. Burgess

About 100 tests of flammability were carried out with H2, CH4, and CO in mixtures with air using the Federal Bureau of Mines 12-ft-diameter spherical pressure vessel as an explosion test chamber. The LeChatelier approximation gave slightly conservative estimates of the limits of downward flame propagation (onset of significant pressure rise) using the following measured values for the individual gases, in percent: H2, 8.5; CH4, 5.25; CO, 13.0. No justification could be offered for using the LeChatelier law for upward flame propagation limits and indeed reported data suggest that calculated values would not be conservative. The observed upward limit for methane-air mixtures (4.85 pct) was less than the widely accepted lean limit for this fuel; those for lean hydrogen-air mixtures and carbon monoxide-air mixtures did not differ from the lowest accepted values. Diffusional effects on the propagation of single, binary, and ternary fuel mixtures are discussed.

Jan 1, 1982

By Gilbert M. Farrior

The electrical resistivity the coefficient of electrical resistivity the Hall coefficient, and the absolute thermoelectric power were determined in this Bureau of Mines investigation for nine compositions of the TiB2-CrB2 sub-system. The numerical values of the electrical resistivity and the thermo-electric power were greater for the intermediate compositions than for the end members. The absolute values of the Hall coefficients and the coefficients of electrical resistivity were less for the intermediate compositions than for the end members. The electrical resistivities and Hall coefficients were about the order of magnitude of most metals--from 34 to 202 microhm-cm and from about 0 to -23.3 X 10-4 cuP/coulomb. The thermoelectric power was somewhat greater than that of most metals--up to 15.6 microvolts per 0 C.

Jan 1, 1965

By Bing W. Jong

A bench-scale evaluation of coal and coal waste materials as aggregate materials for use in longwall mine supports was undertaken as part of the Bureau of Mines Health and Safety program on ground control. Performance data were obtained on portland cement concretes (PCC) prepared with coal and coal wastes as aggregate materials. The effects of high-early-strength accelerators on strength and creep and of superplasticizers on strength properties of PCC formulated with coal and coal waste were investigated. Concrete formulated with a high-early-strength accelerator and coal and coal waste has 20 and 40 pet greater compressive strength, respectively, than the control samples without admixture. A concrete formulated with coal waste and the high-early-strength accelerator, using four bags of cement per cubic yard and a water-cement ratio of 1.0, had the lowest creep value of all the coal- and coal-waste-formulated PCC's tested.

Jan 1, 1983