Search Documents

By L. B. Pankratz

The heat content above 298.15° K was determined for crystalline vanadium silicide of the composition V3Si. This substance has a minor thermal anomaly (probably a heat-capacity maximum) near 560° K; the extra heat absorption is about 50 cal/mole. The original heat-content data are presented, and smooth values of the heat content and the corresponding entropy increments are listed for the temperature range from 298.15° to 1,500° K. Equations representing the heat- content values and derived heat capacities are also included.

Jan 1, 1963

By Liming Yuan

A study of the ignition of non-fire-resistant hydraulic fluid sprays was conducted by the National Institute for Occupational Safety and Health. Both an open flame and a hot steel surface were used as the external heat sources. With the open flame as the heat source, the minimum oil temperature and minimum spray nozzle pressure that resulted in an ignition were measured. The effects of the distance between the open flame and the nozzle and the nozzle orifice diameter on the ignitability of the hydraulic fluid sprays were examined. With the hot surface as the heat source, the minimum surface ignition temperature was determined. The degree of oil atomization and the relative direction of oil injection with respect to the hot surface are discussed. The ignition of oil sprays from the impingement of oil jets onto a vertical surface was also investigated. Finally, the results are compared with those obtained for fire-resistant hydraulic fluids. Keywords: Ignition; hot surface; open flame; hydraulic fluid

Jan 1, 2006

By R. H. Lien

The Bureau of Mines investigated nitrous oxide (N20) stability when used as a solvent for organic removal from metal powder surfaces. Both supercritical and subcritical conditions were studied. This investigation was prompted by the occurrence of a violent reaction when supercritical N20 was being used to deoil a metal powder grinding waste sample that contained 20 to 25 wt pct cutting oil. Tests were conducted to determine the cause of the reaction and to define stability limits. Test data showed that the waste's oil fraction reacted violently with N20 acting as an oxidizer; the metal powder acted as a promoter to reduce the ignition temperature. Although the data were scattered, this temperature appeared to reach a minimum at a certain pressure (dependent on vessel and sample size). The minimum ignition temperature for a 0.64-g sample in a 72-cm3 vessel was 360° C at 200 psig. As the sample size increased, the ignition temperature decreased. For example, when the sample size was increased to 10 g, a reaction occurred at 240° C and 600 psig. Because of the variability of ignition temperature with pressure and sample size, safe operating conditions were not established. Overall, this research showed that extreme caution should be exercised when using N20 in an organic or organic-metal system.

Jan 1, 2011

By J. E. Chilton, T. Mal

Methane monitoring at the mine face is essential to assure a safe work environment in underground coal mines. Machine-mounted methane monitors must be used to continuously monitor methane levels during mining. Monitors used on mining machines must be approved by MSHA and properly maintained to provide protection for workers (30 CFR 75.342). To provide protection the instrument must give accurate readings of current methane levels. Accuracy is maintained by calibrating the instrument with a standard gas at least once every 31 days. Instrument “response time” determines how quickly measurements will change to reflect current concentrations. At present there are no criteria for measuring the response time for a ma-chine-mounted methane monitor while underground. This study examined a procedure for measuring the response time of a machine-mounted methane monitor. Response times were measured using methanometers obtained from three different manufacturers. The effects of the measurement technique and methanometer sensor head design on response time measurements are investigated. Techniques for reducing variation in response time measurements are discussed.

By B. J. Dalton

The Bureau of Mines Helium Research Center has developed a computer program for solving two-phase equilibria data for binary mixtures and for evaluating thermodynamic functions of interest, including all critical points. This computer program was used to calculate equilibrium points on the PVTu surface for the helium-nitrogen system as predicted by the Van der Waals equation of state. Numerical values are tabulated and illustrations are presented for 1,279 equilibrium points and for quantities needed to construct Ponchon diagrams. Equilibrium ratios as a function of pressure at constant temperature and of temperature at constant pressure-are also shown graphically. In addition, saturated partial molal volume and partial molal enthalpy data are given. It is shown that the Van der Waals helium-nitrogen system exhibits retro-grade condensation of the second type for liquid helium concentrations of about 0.07 mole fraction or less and pressures below about 45 atm. It is also shown that the critical point is at a -maximum value of pressure (at constant temperature) and of temperature (at constant pressure).

Jan 1, 1971

This is the third in a series of reports on properties of commercial motor fuels, made in accordance with a cooperative agreement between the Cooperative Fuel Research (C. F. R.) Committee and the Bureau of Mines of the Department of the Interior. The first report gave data on motor gasolines sold during the winter of 1935-36.3/ The second report gave the same data for motor gasolines sold during the summer of 1936)4/ As was the case with the first cooperative gasoline survey, reports were received for some areas from only one company and in other areas from two companies that did not in all instances report on the same brands of gasoline. In still other areas reports were received from five or six companies on the same brands of gasoline. Thus, it can be seen that data on gasolines are unequal in regard, to the number of reports that were averaged in calculating the data shown in table 1. The data from the Pacific Coast were averaged by the Pacific Coast technical group before submission and are published exactly as they were submitted.

Jan 1, 1937

This is the third in a series of reports on properties of commercial motor fuels, made in accordance with a cooperative agreement between the Cooperative Fuel Research (C. F. R.) Committee and the Bureau of Mines of the Department of the Interior. The first report gave data on motor gasolines sold during the winter of 1935-36.3/ The second report gave the same data for motor gasolines sold during the summer of 1936)4/ As was the case with the first cooperative gasoline survey, reports were received for some areas from only one company and in other areas from two companies that did not in all instances report on the same brands of gasoline. In still other areas reports were received from five or six companies on the same brands of gasoline. Thus, it can be seen that data on gasolines are unequal in regard, to the number of reports that were averaged in calculating the data shown in table 1. The data from the Pacific Coast were averaged by the Pacific Coast technical group before submission and are published exactly as they were submitted.

Jan 1, 1937

By Murray Jacobson

The respirable dust standard in the Federal Coal Mine Health and Safety Act of 1969 is designed to prevent disability and death from coal workers' pneumoconiosis. Beginning June 30, 1970, the operators of coal mines were required to maintain the average concentration of respirable dust in the active workings at or below 3.0 milligrams of dust per cubic meter of air. The standard is reduced to 2.0 milligrams per cubic meter after Dec. 30, 1972. This paper presents the equipment and procedures used by the coal mine operators in implementing the respirable dust sampling program established by the Secretary of the Interior and the Secretary of Health, Education, and Welfare and shows the effect of the law, during the first year, on the reduction of dust levels in selected mines. The system employed by the Bureau of Mines for analyzing and processing the dust samples is also presented.

Jan 1, 1971

By C. L. Chaney

Investigations were conducted to develop spectrochemical methods capable of determining 0.01 to 100 micrograms of metals in 50 milliliters of solution. The use of gallium hydroxide (Ga(OH)3) as a carrier-precipitant to concentrate metallic ions is described. A porous-cup graphite electrode is used to collect the precipitate. A specially designed plunger permits the electrode assembly to serve as the sample-containing electrode in the subsequent spec-trographic analysis. Analytical curves are presented for antimony, arsenic, beryllium, and zinc. Sensitivities of detection are given for 13 elements. The techniques were applied to identify impurities separated from tungsten, to determine trace impurities in solutions containing high concentrations of magnesium, cobalt, or nickel, and to identify trace impurities in hydrofluoric acid. Laboratory glassware was a serious source of contamination when low levels of zinc were determined.

Jan 1, 1963

By G. R. Strimbeck

The Federal Bureau of Mines has been developing processes for producing synthesis gas directly from coal, oxygen, and superheated steam. An atmospheric-pressure pilot plant was constructed and operated to: 1. Determine the operability of the plant for gasifying coals of different ranks under various operating conditions. Listed in decreasing order of rank, these coals included a Pennsylvania anthracite, a bituminous A coal from the Sewickley bed, West Virginia, and a subbituminous C coal mined in the Lake de Smet region of Wyoming. 2. Determine the effect of varying operating conditions on: (a) Standard cubic feet (std.c.f.) of oxygen and pounds of coal of different rank required to make M std.c.f. of product gas (carbon monoxide plus hydrogen); (b) carbon gasified, percent; (c) exit-gas temperature, degrees F.; and (d) heat loss, B.t.u. per pound coal. 3. Compare the gasification characteristics, indicated in item 2, of coals of different rank: Bituminous A, anthracite, and subbiturninous C. 4. Determine the concentration of dust in the gases produced and the efficiency of dust removal, and investigate the relation between the sulfur content in the coals gasified and the gases produced.

Jan 1, 1960

By Raja V. Ramani

The potential usefulness of reclaimed surface-mined land has received much attention recently. In an effort to develop a procedure for evaluating postmining land use potentials, specific mines in various regions of the U.S. were studied to determine the extent of current mined-land planning and to discover characteristics that are regional in nature. As part of this investigation, the Chinook Mine-West Field, located in western Indiana, has been studied. The Chinook Mine is presently operated by AMAX Coal Company and has been in continuous operation since 1928 under various ownership. The status of current reclamation and land use planning was reviewed. In addition, site planning principles were applied to the active mine area. This application included formation of a data base and development of postmining land use plan alternatives. Key factors affecting site potential realization for midwestern area mines have been identified along with suggestions for applying land use planning processes to mined-land planning.

Jan 1, 1983

By Fredrick L. Johnson

In 1984, at the request of the U.S. Forest Service, the U.5, Bureau of Mines began a study of the 94,370-acre Arc Dome study area (4-667) in order to appraise its mineral resources, The Bureau of Mines mapped and sampled mines, prospects, and mineralized sites in and near the area, The study area is located in the Toiyabe National Forest, about 54 mi north of Tonopah, Nye County, NV, It is estimated that over 500 claims have been staked in the study area since the mid-1800?s. In January 1986, there were 108 active mining claims completely inside and 59 on the boundary. Another 283 active claims were outside the study area but within 1 mi of the boundary, In addition to the large number of claims staked, exploration activity is also reflected by the almost 700 inactive workings that were found during field investigation.

Jan 1, 1989

By Sidney Katell

This Bureau of Mines study estimates typical capital investments, operating costs, and selling prices for two bituminous coal strip mines in the Eastern and Interior provinces and a subbituminous coal operation in the Northern Great Plains province. The annual productions were based on tonnage required to fuel a 250-million-standard-cubic-foot-per-day, high-Btu gas plant. The annual tonnage for the Eastern province mine is 4.8 million tons; for the Interior province mine, 6.72 million tons; and for the Northern Great Plains province mine, 9.2 million tons. It is assumed that the mines have a 20-year life. Wages and union welfare payments are considered as of December 6, 1974, under the terms of the Bituminous Wage Agreement of 1974, and costs for material and equipment are based on 1975 indexes. Initial capital investment varies: $65,137,900 for the 4.8-million-ton-per-year (MM tpy) mine in the Eastern province, $78,514,600 for the 6.72-MM-tpy mine in the Interior province, and $42,050,100 for the 9.2-MM-tpy mine in the Northern Great Plains province. Total capital investments for the Eastern province mine, the Interior province mine, and the Northern Great Plains province mine are $86,969,900, $109,378,500, and $78,543,500, respectively. Corresponding selling prices for the coal, per ton, are $6.94, $6.03, and $3.39, assuming a 15-percent discounted cash flow rate of return after Federal income taxes. These studies are considered typical for the areas involved. Costs will vary depending on specific locations in these areas.

Jan 1, 1976

In presenting this list of permissible explosives and blasting devices, the Bureau of Mines desires to call attention to pages 19 and 24 outlining, the conditions in use under which, and only under which, the explosive or blasting device is permissible. In view of a recent publication recounting trade practice favoring the use of a blasting device without stemming, particular emphasis is placed upon condition 4 on page 19 and condition 2 on page 24. An explosive or a blasting device enumerated in the permissible lists of this Bureau is not permissible in use unless it is properly confined with clay or other incombustible stemming.

Jan 1, 1940

In presenting this list of permissible explosives and blasting devices, the Bureau of Mines desires to call attention to pages 19 and 24 outlining, the conditions in use under which, and only under which, the explosive or blasting device is permissible. In view of a recent publication recounting trade practice favoring the use of a blasting device without stemming, particular emphasis is placed upon condition 4 on page 19 and condition 2 on page 24. An explosive or a blasting device enumerated in the permissible lists of this Bureau is not permissible in use unless it is properly confined with clay or other incombustible stemming.

Jan 1, 1940

By George F. Dana

Oil yields, lithology, and stratigraphy have been evaluated for 15 cored wells and two sampled wells representing 10 square miles of the Tipton Member of the Green River Formation near Green River, Wyo. The area evaluated is being used by the Bureau of Mines for experimental production of oil from the oil shales in place. Lithology and oil yields were correlated to produce a stratigraphy diagram for the in situ study area, permitting precise designation of comparable sections. Because of lateral uniformity of oil shale, oil yields from eight cores and two sets of drill-cutting samples within a quarter section show the range of variation in average oil yield arising from experimental error. Variation in average oil yields from the seven cores representing the 10-square-mile study area lies within the expected experimental error. No difference in oil-shale richness across the study area is indicated. Average oil yields for three Tipton sections in the study area were deter-mined as follows: (1) The entire Tipton Member oil shale (about 145 feet thick), 13.3 gallons per ton; (2) the 40-foot upper rich zone, 21.0 gallons per ton; and (3) the 21-foot zone in which the Laramie Energy Research Center is conducting in situ experiments, 22.4 gallons per ton. One acre of the 21-foot experimental section represents 34,300 barrels of oil in place, and 1 acre of the Tipton's 40-foot rich upper layer represents 62,000 barrels.

Jan 1, 1972

Consumption and intensity of use trends for 12 metals, by industrial end use, were estimated for 1972 through 1982 by the Bureau of Mines and U.S. Department of Commerce. The trends were then forecast through 1993 using standard statistical methods. The intensity of use measure selected is the quantity of metal consumed per constant dollar output of a specific industrial sector. The metals studied were aluminum, chromium, cobalt, copper, lead, manganese, nickel, the platinum-group metals, tin, titanium, tungsten, and zinc. Average annual growth rates for the following 4 of the 12 metals increased from 1972 to 1982 as follows: aluminum, 1.00%; platinum-group metals (consisting of platinum, palladium, and iridium), 8.83%; titanium, 7.82%; and tungsten, 6.09%. Consumption for the remaining eight metals decreased at average annual rates ranging from 0.58% (copper) to 5.37% (manganese).

Jan 1, 1986

By Fred D. Wright

The objectives of this research were: 1. to determine the stability relationships of coal mine roof rocks which are cut by fractures or intersecting joints with and without roof bolts, under various sets of conditions including horizontal formation pressures, inclination and coefficient of friction of joints, bolt loads, roof spans and rock properties; and 2. to develop criteria for the design of roof bolt sys terns for such roofs. The problem was studied by mathematical finite element models and by laboratory models. From the results of the mathematical and laboratory models, equations were derived to express the relationships listed above for cracked, single-layered roof beams and design tables for such beams are included. The analysis was then extended to include multi-layered cracked beams reinforced by roof bolts and a method for analyzing and designing bolting patterns for such roof rocks is presented.

Jan 1, 1974

By Maria I. De Rosa

The U.S. Bureau of Mines performed experiments to determine the embedded hydrogen chloride (HCI) and smoke particle characteristics during combustion of polyvinyl chloride (PVC) and chlorinated mine materials for development of a test parameter. The experiments were conducted in an approximately 20-L furnace at set furnace temperatures of 250° and 1,000° C, for a 14-min duration, with an airflow through the furnace of 10 L/min. The variables studied, as a function of time, were hydrogen chloride embedded on smoke particles, hydrogen chloride concentrations in the gas phase, smoke particle average diameter (dg) and particle concentration (no), and product of smoke particle diameter and concentration (dgno). Other variables included carbon monoxide (CO), carbon dioxide (CO2), and oxygen (O2) concentrations; sample mass weight loss; and furnace temperatures. Results show that there is a correlation between embedded hydrogen chloride, hydrogen chloride gas concentrations, and inverse of the smoke particle diameter-concentration product (1/dgno); the higher the hydrogen chloride gas concentrations, the higher the embedded hydrogen chloride, the higher the 1/(dgno) values. These correlations will enable development of a simple test parameter to assess the toxic hazard that these materials pose during fire.

Jan 1, 2010

By E. J. Matson

"SUMMARYThe Bureau of Mines has been investigating deposits of critical and essential minerals in the United States since 1939. Projects were set up on only the most promising properties. A preliminary examination of the Rio Grande property was made by Bureau of Mines engineers in July 1942 and the property was examined again in July 1943.The Geophysical Branch of the Bureau undertook a Geophysical survey of the area in November 1943 and was intermittently active in the district until June 1946. The major portion of their work was done from June 191 to November 1945. Favorable areas for exploration were recommended by the Geophysical Branch of the Geological Survey, 3/ and all holes were drilled in them.Two projects were set up by the mining branch in an endeavor to find ore bodies on the strength of the geophysical information."

Sep 1, 1947