Search Documents

By Israel Liebman

The Bureau of Mines conducted an investigation to determine those factors that are significant in affecting the velocity of flames propagating along the boundary separating gaseous fuel and air. In addition the aerodynamic motion of the gases in the vicinity of such interfacial flames was delineated. Parameters in the study included flammable zone thickness, flammable zone concentration of gradient, fuel type, and position of the flame relative to various environmental surfaces. Of all these factors, the flammable zone thickness and burning velocity of the stoichiometric mixture were found to have the most significant effect on the flame speed. Notion of the gases in the vicinity of the interfacial flames was examined by particle track and interferometric techniques. The relative velocity of the interfacial flame with respect to the unburned gas on the central streamline was found to equal the burning velocity of a stoichiometric homogeneous fuel-air mixture. In addition, it was observed that the composition of the lean fuel-air mixture at the boundary of the combustion zone appears to be less than that defined as the fuel's lower flammable limit.

Jan 1, 1968

By H. G. Iverson

The effects of adding boron and boron plus carbon to electrorefined vanadium were evaluated with respect to mechanical properties at low temperatures and response to heat treatment. Grain size was significantly decreased with the addition of 0.05 percent boron, the decreases ranging from 30 percent at 800° C to 75 percent at 1,100° C. Increasing the boron content resulted in only a small increase in strength at room temperature, but at 77° K, boron contents of 0.005 to 0.076 percent increased the yield strength of vanadium over 50 percent, from 70,000 psi to 110,000 psi. When boron and carbon were present together, the individual grain-refining effects obtained with either element were retained. Approximately a twofold increase in strength was obtained by age-hardening the alloys containing both boron and carbon. Alloys with only boron additions did not age-harden.

Jan 1, 1968

By John R. Reeves

The data presented in this paper form the chief part of a general survey of the oil-shale resources of Indiana. Other papers* have already been published which contain data an various aspects of this resource. In combination, these papers present data with reference to the following points; (1) distribution of the New Albany shale; (2) amount of shale available; (3) homogeneity and thickness of the formation; (4) amount and quality of the oil obtained from the shale; (5) nitrogen content of the shale; (6) extractibility of the shale and its amenity to breaking; (7) some economic factors bearing upon the utilization of the shale; and (3) other miscellaneous factors and data. In the future, technical work on other phases of the general problem is expected to be done with the object of making a complete survey of this resource which is of much potential importance to the state and nation.

Jan 1, 1923

By Frank M. Vodoklys

This is the final report on Contract H0220049 covering the period from 27 April 1972 to 30 April 1974. The objective of the contract was to develop and evaluate materials and methods to achieve post explosion identification of explosives reliably and economically through the use of phosphor coded grains incorporated into the explosive during its manufacture. A coding system of two spotting phosphors and seven coding phosphors was successfully developed during the execution of the contract. The ability of the coded grains to survive detonation in many different types of explosives was demonstrated and the complete code was extracted from a single 100 micron post-explosion fragment. A method was established for testing grain strength to correlate with field test results and an optical system was designed for extracting the code from the grains. Also in fulfillment of the contract requirements a laboratory method for manufacturing the coded grains was established and ten one-pound samples, each with a different code, were fabricated. Finally, a method was developed for applying a coating of polyethylene to the grains to prevent sensitization of the tagged explosives and the ten one-pound samples were coated and delivered to the Bureau of Mines.

Jan 1, 1974

By Kevin Hennings

Screening efficiency models developed to date rely almost exclusively on empirical formulas based upon large amounts of acquired operating data. A screening model was developed using a combination of empirical coefficients and explicit mathematical expressions which quantify screening phenomena. A series of screening tests was run to supply data for purposes of correlation and empirical coefficient evaluation. The model has been implemented as a digital computer program. The validity of the modeling procedure has been established by laboratory testing. Results generated by the model have been used to compile an applications handbook, which can be used to predict screening performance in lieu of using the computer program.

Jan 1, 1982

By Stephen C. Tadolini, Gabriel S. Esterhuizen, Anthony T. Iannacchione

A Major Hazard Risk Assessment (MHRA) was developed in Australia after a series of mine disasters in the 1990’s. A MHRA is used to help prevent major hazards, i.e. fire, explosion, wind-blast, outbursts, spontaneous combustion, roof instability and chemical and hazardous substances, from injuring miners. A MHRA is a structured process that identifies the characteristics of major hazards, assesses and ranks the risk they present, and evaluates engineering and administrative controls to mitigate them. These controls typically consists of a broad spectrum of prevention, monitoring, first response, and emergency response techniques and helps to move an operation from a reactive to a proactive approach towards safety. This paper documents a MHRA performed at an underground mine where strata instabilities and fire hazards may threaten the condition of its escapeways. The objective of this MHRA is to 1) identify what hazards could affect the egress through the mine’s escapeways, 2) determine what unwanted events pose the greatest threat for the mine, and 3) recommend a plan to prevent or recover from the potential disruption of egress through the escapeway. The plan provides information on the key existing controls that should be monitored and audited, and makes recommendation of new potential controls to further reduce related risks. By documenting the use of MHRA to this specific ground control issue, this paper provides a framework for others to judge the merits of this approach and to help design and perform these activities.

By James C. Cawley

This report presents results of recent Bureau of Mines research to establish the probability of spark ignition as a function of current (or voltage, for capacitor circuits) for resistive, inductive, and ca-pacitive circuits in 8.3% methane-air atmospheres. The data presented quantify the explosion hazard created when low-power electronic devices catastrophically fail in an explosive mine atmosphere. Previous litera-ture dealt with levels of probability between 10-3 and 10-4. This re-port extends the probability data to levels as low as 10-7. This study has verified that when the probability of ignition, PI, is plotted on a log-log coordinate system versus the current (or voltage), a continuous, straight-line relationship is formed. An interesting result that can be statistically hypothesized is that at some low level of igniting current the ignition process ceases altogether.

Jan 1, 1988

By Derek Ellis

Volume II of this two-part series on Submarine Tailings Disposal (STD) as a tailings management option for coastal and island mines contains descriptions of lesser known case histories. The Misima gold mine (Papua New Guinea) and the Black Angel lead-zinc mine (Greenland) are described in some detail as the best documented cases. Atlas copper mine (The Philippines) is less fully described due to relative lack of documentation. The Misima and Atlas STD systems are working to their design criteria. At Black Angel the system adopted did not prevent contamination for a number of reasons, which are now understood. Two cases are described where STD is being developed. They are the Cayeli Bakir copper mine Turkey), and the Toquepala and Cuajone mines (Peru). There is excellent documentation available for both cases. Three case histories are described where tailings have reached the sea either through beach or river discharge. In one case the STD option has been explored (Marcopper Mine, The Philippines). In the others we explore in hindsight whether STD might have been a viable alternative using the Screening Criteria that this Volume develops - see below. The mines are Bougainville Copper Mine in Papua New Guinea, and Jordan River Mine (Canada). There is potential for STD at all three sites. Finally, the Volume presents Screening Criteria for appraising STD, based on the experience in design, operation and environmental impact reviewed in the case histories.

Jan 1, 1994

The contract objective was to evaluate sources of airborne quartz and research control methods that would assist underground mine operators in complying with respirable dust standards which have been reduced because of quartz in the dust exceeding five percent. The work involved: Phase I -evaluate sources of quartz dust at the roof bolter work location; Phase II -evaluate the relationship between the quartz content of the coal and adjoining rock strata and quartz exposure at the roof bolter and continuous miner locations Phase III -conduct laboratory tests to determine performance parameters for roof bolter dust collector systems. The underground surveys for Phases I and II determined: (1) the continuous miner typically is the greatest source of quartz exposure for the miner and roof bolter operators when single-split ventilation is utilized, (2) a statistically significant relationship be­tween quartz content in face material and operator exposure was not determined and data suggested mining equipment and procedures may be more critical. The Phase III lab tests indicated the use of dust hog-type bits, filter cartridges, maximized collector airflow, and reduced bit rpm should be utilized to minimize dust liberation at the roof bolter.

Jan 1, 1985

By Carl Rampacek

Recent research by the Bureau of Mines has demonstrated that the segregation process has merit for treating oxidized and mixed oxide-sulfide copper ores. The process comprises heating the crushed ore with salt and coke or other carbonaceous materials at about 700° C. to produce fine flake copper, which then is recovered by conventional copper-flotation methods. Bench-scale laboratory tests of a number of oxidized and mixed copper ores assaying 0.78 to 5 percent Cu gave copper recoveries of 73 to 96 percent. The flotation concentrates assayed 21 to 76 percent Cu, depending on the ore being treated.

Jan 1, 1959

By Eugene L. Grumer

High-expansion foam was applied to the flames of six fuels burning in a 1-foot-diameter tray. The flames of three hydrocarbon fuels were more readily extinguished than the flames of methanol, acetone, or unsymmetrical dimethyl hydrazine. The result is rationalized on the basis that heat transfer from flame to fuel surface is primarily radiative with the hydrocarbons and more largely convective with the nonhydrocarbons. INTRODUCTION Equipment for producing high-expansion foams has been developed by the Bureau of Mines to control coal mine fires.5 Recently such equipment has been redesigned for portability and has now been produced commercially for other fire-fighting applications. In May 1961, a 50-by 50-foot gasoline fire was extinguished within 2 minutes by a trailer-mounted foam unit that produced 12,000 cu.ft./min. of high-expansion (1,000:1) foam.6

Jan 1, 1962

By O. C. Blade

This report on the properties of motor fuels sold through service stations in the United States was made in accordance with a cooperative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. By agreement with the American Petroleum Institute, identification of the items is confidential. It presents analytical data for 4,680 samples, representing the products of 130 companies. The samples were collected during December 1953 and January and February 1954. As in previous surveys, the gasolines covered by this survey include those from both large and small suppliers. The data were obtained by laboratories of various refiners, motor manufacturers, and chemical companies and submitted to the Bureau of Mines for compilation. A list of the National Motor-Gasoline Survey reports published during the past ten years is given on page 5.

Jan 1, 1954

By T. M. Nasiatka

This report sterns from a study undertaken by the Federal Bureau of Mines to determine the possibility of reducing filter-cake moisture by applying radiant heat. Suitable laboratory equipment was set up to study the effect of heat, heating time, proximity of the heater to the filter cake, cake thickness, and other variables related to the final filter-cake moisture. A minus-48-mesh coal slurry and application of heat for 60 seconds resulted in filter-cake moistures 5.6 to 13.2 percentage points lower than could be accomplished by filtration alone at 24 inches of Hg for 1-1/4-and 1 1/2-inch cake thickness, respectively. The moisture reduction can be attributed to the combined effect of lower fluid viscosity and evaporation.

Jan 1, 1959

By O. C. Blade

This report on the properties of motor fuels sold through service stations in the United States was made in accordance with a cooperative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. By agreement with the American Petroleum Institute, identification of the items is confidential. It presents analytical data for 4,421 samples, representing the products of 131 companies. The samples were collected during June, July, and August, 1953. As in previous surveys, the gasolines covered by this survey include those from both large and small suppliers. The data were obtained by laboratories of various refiners, motor manufacturers, and chemical companies and submitted to the Bureau of Mines for compilation. A list of the National Motor-Gasoline Survey reports published during the past 10 years is given on page 5.

Jan 1, 1954

By J. J. Shields

This is the Seventh of a series of publications that describe methods and practices used in mining bituminous coal mechanically.3/ This report deals with the operation referred to in coal mining as continuous mining, and the interest shown by mining companies in this method is the reason for this study. Only continuous mining as it applies to the room-and-pillar system of mining, or a modification thereon, is discussed in detail in this report. Although not always as continuous as the name implies, it is a system of mining in which a machine is used to cut and load coal in one continuous operation without drilling and blasting the coal. With the mining equipment in most general use today, the usual cycle of operation in mining of coal is: (1) Timber, (2) cut, (3) drill, (4) blast, and (5) load. As the phases of this type cycle cannot be performed simultaneously in the same working place, it is necessary to operate from 3 to 7 working places so that at least 1 place is available for coal loading at all times. Even if the schedule of the phases in a cycle is maintained, coal production ceases during the time required to move the loading equipment from one loading place to the next. In 1920 a continuous-type mining machine4/ was installed in an Illinois coal mine to drive entries. Several other companies used these entry drivers for short periods in the following few years. In 1927 a southern Illinois coal company installed 2 of these machines which, in the next 25 years, were reported to have driven over 200 miles of entries. The machines did not attain widespread usage.

Jan 1, 1954

By R. C. Hickman

"INTRODUCTION The most productive area of the eastern Virginia pyrite belt lies to the north of the village of Mineral., in Louisa County. The largest producers of pyrite ore in the area were the Armenius, Boyd Smith, and the Sulphur mines.The Boyd Smith mine started production about 1890 and operated more or less continuously until 1922, when competition from the Gulf States and Spain closed the pyrite mines in Virginia. There are no reliable records of production or value of minerals produced.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the most effective utilization of our mineral resources to the end that they take the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, Oliver C. Palston, chief, analyzes samples and performs beneficiation tests.The project was under the immediate supervision of Mitchell H. Kline, chief, Raleigh Division, Mining Branch, Bureau of Mines.LOCATIONThe Boyd Smith property is reached from Mineral, Va., by traveling north on State Route 522 about 2-1/2 miles. An unsurfaced road, winding in a northwesterly direction, loads to the Boyd Smith headframe, which is about half a mile from State Route 522 (fig. 1). The tract comprises 181 acres."

Aug 1, 1947

By D. T. Holmes, W. G. Sandell

"INTRODUCTION Three representative lots of ore wore obtained from the Aguila minim district in Arizona during the Bureau's exploration of manganese deposits there. Since only selectively mined ore from this district will meet commercial-grade specifications, the ores were studied to determine their amenability to concentration.Although the purpose of the investigation was to determine the possibilities of the district as a source of commercial-grade manganese, testing was sufficiently comprehensive to indicate the response of the ores to several different types of treatment. Many data of secondary importance have been omitted, end only the more pertinent tests are presented in detail.At the beginning of the investigation of manganese-ore beneficiation in December 1940, the only product marketable to. Metals Reserve Company was ferro-grade manganese, grade B, the requirements for which follow: Mn, min., 48 percent; Fe, max., 7 percent; Si02, max., 10 percent; P, max., O.18 percent; Al12O3, max., 6 percent; Zn, max., 1 percent.Later the specifications were modified gradually. As of May 15, 1943, manganese products were acceptable if they contained over 35 percent manganese and less than 3 percent zinc and 1 percent phosphorus. Prices were based upon material containing 48 percent manganese, 6.O percent iron, and. 11 percent silica plus alumina. Premiums were paid for manganese con¬tent over 48 percent and iron content under 6 percent, penalties being imposed upon products containing loss than 48 percent manganese or more than 6 percent iron or more than U. percent. silica plus alumina.. The specifications for commercial manganese further required that the maximum particle size be 12 inches and that 75 percent of the product be coarser than 20-mesh. Therefore, fine material, such as table and flotation concentrates, had to be nodulized or sintered. In addition, carbonate manganese ores were not acceptable unless calcined.."

Aug 1, 1948

By Robert W. Smith

Computation of the thermodynamic properties of the reaction products in the deflagration of explosive gas mixtures has been a most valuable guide regarding the possible kinetic mechanisms of homogeneous combustion processes. Knowledge of the physically possible end states is indispensable for understanding observed deviations from equilibrium in heterogeneous combustion. However such information on dust flames is entirely lacking. To complement a Federal Bureau of Mines study of stationary graphite dust flames burning in pure oxygen,6/ this report gives examples, at atmospheric pressure and room temperature, of composition profiles in an idealized oxygen-dust flame, with both mass and enthalpy being preserved. Similar profiles can be obtained from the data of the paper for elevated temperature and pressure.

Jan 1, 1960

By Edmund S. Leaver, Jesse A. Woolf

"The Baboquivari mining district is about 60 miles southwest of Tucson, Ariz., the present railroad shipping point. The values are silver and gold. The silver is largely associated with the black oxides of manganese. The ore is highly oxidized, and careful panning shows only a very small amount of pyrite. Our sample analyzed as follows:A flotation mill has been installed in the district, but it does not concentrate the precious metals satisfactorily. Our best laboratory flotation results were obtained by grinding to pass 65-mesh and floating with Xanthate or standard flotation oils plus sodium sulphide and polysulphide. This sulphidizing method gave a concentration of 32 per cent of the silver and 80 per cent of the gold, which about equals plant practice.We do not know of an instance where the oxidized forms of manganese have been concentrated satisfactorily by flotation.Plain cyanide on the original ore extracts practically all of the gold but only one-third of the silver. A preliminary deoxidizing roast, using producer gas or powdered coal, gives a calcine from which cyanide dissolves about 90 per cent of the gold and 75 per cent of the silver. This method of treatment, known as the Clevenger-Caron process, is described in Bureau of Mines Bulletin 226.Preliminary treatment with sulphur dioxide by burning pyrite or sulphur and passing this gas into the pulp until all of the contained manganese is dissolved or changed in form best prepares the ore for cyanidation. The acid consumption will vary with the percentage of manganese and other soluble constituents. Neither gold or silver is dissolved by this acid treatment. The washed residue gives maximum cyanide dissolution of the gold and silver with minimum loss of cyanide,"

May 1, 1928

By R. Stefanko

This first Annual Report covers the work on Contract No. H0377043 "Cable for Face Equipment", from August 1, 1977 to July 31, 1978. It reports the progress in the three areas of over-and short-circuit protection, cable ampacity research and cable couplers. Field trips have established many interesting facts related to circuit breaker settings and cable size. For example, the determination of cable sizes depends on the RMS duty cycle current determined by a particular piece of equipment, but the actual selection of the cable to be used is often a function of the maximum allowable circuit breaker instantaneous settings as specified in Title 30. In order to avoid nuisance tripping as a result of instantaneous starting current field, laboratory and analytical studies are being conducted to determine proper settings and cable sizes Also an extensive program has been established to monitor the performance of high voltage cable couplers and determine their modes of failure. Various equipments are being designed for laboratory testing, and an extensive reeled cable experiment is also under way.

Jan 1, 1978