Search Documents

By H. H. Schrenk, L. B. Berger

"INTRODUCTION The Bureau of Mines frequently receives requests for information and advice regarding the equipment necessary for establishing laboratories for the analysis of mine atmospheres. Such requests are made by mining companies, State mining departments, and other agencies concerned with the safety of mining operations. In many instances it is desired to install a complete laboratory, which will necessitate purchase of suitable gas-analysis apparatus and all the minor but important accessory equipment needed to carry on this type of work. Although publications that describe methods and techniques applicable to the analysis of mine atmospheres are available, it is not within the scope of such publications to give detailed information on laboratory equipment or design. Persons unfamiliar with laboratory practices and gas-analysis procedures may find it difficult to decide upon the proper equipment for their particular needs and to itemize the various accessories that must be obtained to set up a complete laboratory.The purpose of this circular is to discuss the different types of equipment that may be used in the analysis of mine atmospheres, with particular regard to the application and limitations of each type. Information on the various accessory equipment needed in a laboratory for the analysis of mine atmospheres is given also, and suggestions on laboratory design are included. As much of the necessary equipment may be obtained from laboratory supply houses, the information should aid in arriving at estimates of the cost of proposed laboratories.The procedures involved in the analysis of mine atmospheres are not described; such information is contained in publications referred to in this circular."

Feb 1, 1948

By Barbara Fotta

According to the Bureau of Labor Statistics (BLS), workforce estimates of median age suggest that the median age of the mining workforce, which has been experiencing overall declines in numbers of employees, is rising more rapidly than for the overall U.S. civilian labor force. In the absence of detailed demographic data for the mining industry, the current study uses injury and illness data reported to the Mine Safety and Health Administration (MSHA) to examine differences, over time and by commodity, in the proportions of injured or ill workers aged 45 years and older. These data indicate that from 1988 to 1998, the percentage of injured or ill older workers (aged 45 years and older) have been steadily increasing. The most notable increase occurred at coal mining operations where the proportion of injured/ill older workers increased from 24 to 44 percent. A more detailed breakdown of the industry by commodity for 1998 showed the highest proportions of older injured/ill workers (over 40%) occurring in coal, iron ore, alumina mills, cement, and trona operations. In coal operations, as the employment size of the mine operation increased, so did its proportion of older injured/ill workers. Also, higher proportions of older injured/ill workers were observed at surface coal work locations than at underground locations. The distribution of older injured/ill miners by occupation for several select commodities shows the highest proportions for supervisors, electricians, mechanics, and surface equipment operators, and the lowest proportions for surface laborers and for underground coal roof bolters and scoop operators. With few exceptions, older injured workers have the highest median number of days lost per injury when examined by type of mining operation and by occupation. Given the high proportions of older injured or ill workers in many sectors of the mining industry, health and safety programs must consider the physiological changes associated with aging when evaluating job tasks and the working environment.

Jan 1, 2004

By Stanley M. Walker

Safety consciousness is not a constant for which a specific value can be assigned, but is a variable, which is frequently intangible. Its evaluation is not simple. We all know that safety consciousness is the most potent factor in the prevention of accidents. Safety consciousness may be defined as awareness of hazard and alertness to danger, which controls every action of an individual through his desire to remain alive and uninjured.

Jan 1, 1951

By Forest H. Majors

"INTRODUCTION The Brutch sulfur deposits were explored by the Bureau of Mines during the spring and summer of 1944. Old workings were rehabilitated and sampled, test pits and shafts were sunk, and trenches were cut through the surface alluvium.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts prelimi¬nary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director.Special acknowledgment is due S. R. Zimmerley, regional engineer, and Paul T. Allman, principal engineer, Bureau of Mines, Salt Lake City, for their supervisory aid, and to the metallurgical staff, Salt Lake City, for beneficiation of samples."

Oct 1, 1946

By S. H. Ash

THE INVESTIGATION of barrier pillars in the Western Middle field is part of the comprehensive study of the mine-water problem in the anthra¬cite region of Pennsylvania by the Federal Bureau of Mines (1, 2, 5, 6, 7, 8,9,10,11,1,2,15,16).8 The Western Middle field is in Schuylkill, Columbia, and Northumberland Counties in eastern Pennsylvania. It has an area of 120 square miles, is 42 miles long from Delano on the east to Trevorton on the west, and is 2 to 5 miles wide. In the Western Middle field are 58 underground water pools containing 38 billion gallons of water (5). Some of the pools overflow to the surface, and the water from others seeps into adjacent mines through permeable barrier pillars separating them from abandoned mines. Several active mines are interconnected to workings in abandoned mines, which are partly filled with water. These mines are separated by barrier pillars that are considered effective only below the altitude of the connections. In some abandoned mines, pumping stations maintain the water at altitudes where the hydrostatic pressure against the barrier pillars is not excessive and does not endanger adjacent active mines. If water in these abandoned mines is allowed to rise to where it can overflow into the active mines, it must be pumped from the active mines at lower altitudes; this materially increases the cost of pumping. It is estimated that from 1944 to 1948 approximately 30 percent of the water pumped to the surface was from abandoned mines.

Jan 1, 1953

By James C. Barker

Alluvial cassiterite concentrations are widespread in river gravel and high level terraces within the Ray River watershed. The area lies in unglaciated terrain of Alaska's northern interior. Cassiterite originates from several calc-alkaline plutons of the Ruby batholith. Extensional stresses resulted in graben-like Tertiary basins that were flooded by a 200 ft thick section of mid-to late- Tertiary basalt flows. Basalt blocked local drainages, and 50- to 100-ft of terrace gravel was eventually deposited on top of the flows. Further downwarping and eventual fluvial downcutting of the flows resulted in cycles of accelerated sediment transport, deposition, and reconcentration. Repeated erosional cycles concentrated heavy minerals and resulted in development of tin placers. Preliminary resource estimates of contained tin in Recent alluvium range from 62 to as much as 172 million lbs-Sn in 300 million yd3. Grade of about 90% of the gravels is estimated to range between 0.2- to 0.5- lbs-Sn/yd3. Associated gold and rare earth elements (REE) in monazite and xenotime may be recoverable. Most of the tin is considered a subeconomic inferred resource, though, at least some of the gravels contain 2-to 6-lbs-sn/yd3. Estimates are projected on the basis of surface sampling and several auger drill holes and are provided for the purpose of land-use management planning.

Jan 1, 2011

By Robert J. Pokora

This report summarizes the work performed under USBM Contract No. J0100038, "Demonstration of Noise Control Techniques for the Crushing and Screening of Nonmetallic Minerals." The objectives of the program were to: a. Identify the prevalent sources of crushing and screening noise in portable and stationary plants b. Design retrofit noise control treatments for those sources c. Field test control treatments under actual operating conditions. A census of the nonmetallic industry was performed to determine the number and types of crushing and screening equipment. Based on the census, eight plants were selected and surveyed to assess the variety of noise sources, determine the worker noise exposure to those sources, and to identify possible constraints that had to be considered in designing and installing the retrofit controls. Three plants were selected from those surveyed and retrofit noise control treatments were designed, including: a. A primary crusher operator control booth b. Screen decks made of resilient cloth c. Screen feedbox impact pads d. Rubber feed plate for secondary crusher e. Rubber feed chute linings for secondary crusher f. Noise attenuating curtain for secondary crusher. A new primary crusher control booth was installed at one plant, and the operator noise levels were reduced from 97 dBA to 78 dBA. Screen noise at the two secondary crushing plants was reduced by 3 dBA to 7 dBA; crusher noise was reduced by 5 dBA at one of these two plants. Noise levels at normal outside operator and cleanup locations were reduced by 4 dBA to 7 dBA at one secondary plant, but operator/cleanup noise levels were not significantly reduced in the second plant due to rapid wear of installed materials. At one of the two secondary plants the retrofit noise control materials displayed excellent wear characteristics. The rapid wear of retrofit materials at the second plant was due to improper materials being supplied and changing circuit conditions.

Jan 1, 1982

By C. W. Owings, L. D. Tracy

"IntroductionMany bituminous coal-mining companies have inaugurated extensive safety Programs, but the failure to have approved or permissible equipment or safe practice in only one part of a mine has resulted in disaster. The necessity of using only equipment bearing the U. S. Bureau of Mines approval plate is emphasized by the fact that many accidents are the direct result of carelessness on the part of trusted employees using non-permissible equipment. A concrete example is found in the case of an explosion on October 26, 1926, in a mine in the Pittsburgh district, Pennsylvania.Story of the ExplosionAt about 10 o'clock on the night of the explosion an examination was made in No 2 butt left and parallel off 7o. 14 north, and was found to be clear of dangerous accumulations of gas. (See figure). Several hours later a crew of two men brought a self-propelling rock-dusting machine within 50 feet of the face of Po. 2 butt parallel before they examined for gas. The machine operator found an accumulation of explosive gas about 18 inches from the roof. He began to wave his arms thoroughly mixing the gas and air. Undoubtedly a highly explosive mixture was created, and as the men attempted to run the machine back to fresh air an explosion occurred.The helper dropped to the floor and was burned about the face and wrists. The machine operator ran down the entry and was more severely burned about the face, neck, and arms. He later developed pneumonia and died. Both men reached the door in the chute between No. 14 and No. 15 north. A pumper, who had felt the rush of air, found the men and helped them to walk outside."

May 1, 1927

By Russell E. Griffin

Dielectric constants and dissipation factors were measured by the Bureau of Mines for 13 simulated lunar rocks over the 20-to 100-megahertz frequency range by means of the susceptance-variation method. Measurements were made at room temperature and normal atmospheric pressure. Results are presented and some comparison is made with data reported by others. The rocks used include a broad range of physical characteristics and chemical compositions from the large areas of volcanism in Oregon and northern California, and two nonvolcanic types. These rocks make up a suite of rock standards used by a group of laboratories engaged in lunar research. The data presented will add to the basic scientific and engineering knowledge needed to utilize extra-terrestrial mineral resources for support of future space missions.

Jan 1, 1974

By Vance G. Leak

A technique for recovering copper and steel from metallic scrap has been developed by the Bureau of Mines based on preferential melting in molten salt baths at 1,150° to 1,250° C, The molten salt, preferably barium chloride or calcium chloride, both minimizes oxidation of the metals and promotes heat transfer. Cleanest separations (0.01 percent copper remaining in iron) have been achieved by pretreatment (dipping or spraying) with sodium sulphate or sodium silicate, which alters and coats the surface of the iron to inhibit the alloying or brazing with copper. An economic evaluation of the process was carried out on six combinations of sweating media and inhibiting reagents. On the basis of the postulated model, a cost of about $0.20 per pound of copper recovered has been determined for the sweating treatment operation.

Jan 1, 1973

By Robert L. Virta

The Bureau of Mines examined a fibrous talc sample from the Gouverneur talc district in New York by transmission electron microscopy (TEM) and polarized light microscopy to determine the mineralogical relationship of the fibrous talc to the amphiboles present in the sample. Two am-phiboles, anthophyllite and tremolite, were present in the sample. Tremolite occurred as a separate mineral phase, which was blocky in habit. Only a few composite tremolite-talc grains were observed. An-thophyllite, however, was present only in the fibrous talc grains. Mi-crodiffraction study of the fibrous talc grains containing anthophyllite showed that the anthophyllite was intermixed with the talc on a fine scale and that there was a crystallographic relationship between the talc and anthophyllite lattices in the fibrous talc grains. A mechanism similar to the process that forms biopyriboles could explain the structural defects, the fibrous habit of the talc, and the structural relationship between the talc and anthophyllite in the fibrous talc grains. Because of these characteristics, phase contrast microscopy and a provisional TEM technique for monitoring asbestos exposure would not distinguish between fibrous talc and fibrous amphiboles. TEM techniques employing electron diffraction and energy-dispersive X-ray analysis are recommended to positively identify the fibrous phases for regulatory purposes.

Jan 1, 1985

By C. Stephan, E. Weiss, J. Trackemas, M. Sapko

The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory (PRL), in collaboration with the Mine Safety and Health Administration (MSHA), the mining industry, and seal manufacturers recently conducted a series of full-scale experiments within the underground experimental mine at PRL’s Lake Lynn Laboratory. The purpose of the experiments was toe valuate the explosion-resistant characteristics of several new seal designs for rapid deployment during mine emergencies. These seals can be deployed in 6 to 10 hr and are capable of with standing explosion overpressures in excess of 140 kPa (20 psi). These novel seal designs use available mine materials, do not require conventional rib hitching, and, most importantly, can substantially reduce exposure time for coal miners during sealing and mine recovery operations.

By E. V. Cilento, K. A. DiGregorio, R. C. Lantz

"K. A. DIGREGORIO, E. v. CILENTO, AND R. c. LANTZ. Measurement of superoxide release from single pulmonary alueolar macrophages. Am. J . Physiol. 252 (Cell Physiol. 21 ): C677-C683, 1987.-An electrooptical method was developed to quantify superoxide (02) release from single rat pulmonary alveolar macrophages (PAM) during adherence to the bottom of a culture dish. This was done by measuring the reduction of nitro blue tetrazolium (NBT) to a diformazan precipitate at 550 nm from videorecorded images of individual cells. Temporal changes in cell optical density, which are proportional to the mass of diformazan produced, were calculated from videophotometric measurements of the change in light intensity over individual cells. Total diformazan produced increased 78 and 1263 with an increase in NBT from 0.5 to 1.0 and 2.0 mg/ml, respectively. Total diformazan produced and maximum rate of production among individual PAM varied two- to threefold providing strong evidence for heterogeneity in 02 production. Specific inhibition of 02 production by superoxide dismutase, iodoacetate, and chlorpromazine significantly reduced the total diformazan produced and maximum rate of diformazan production. Hydrogen peroxide was not involved in NBT reduction, since catalase alone did not significantly change diformazan production. This novel method to quantify 02 release from single PAM should be valuable in analyzing heterogeneity and single cell kinetics of O; production, in assessing the effects of exposure of cells to particulates on O; release, and in relating release to electrophysiological measurements.rat; nitro blue tetrazolium; macrophage heterogeneity; single cell kinetic PULMONARY ALVEOLAR MACROPHAGES (PAM) protect the lungs by phagocytizing foreign debris and bacteria (24). This process involves ingestion as well as destruction of foreign matter. Phagocytosis is usually accompanied by a respiratory burst that increases cellular oxygen consumption and glucose metabolism in the hexose monophosphate shunt (7), which leads to the release of highly reactive oxygen metabolites at the surface of the · plasma membrane (6, 27). These agents have been implicated in the killing of bacteria by phagocytes (22), but have also been shown to be toxic and have been linked to cancer, emphysema, arthritis, diabetes, and other diseases (17, 22, 30). Toxic effects may be a result of either an abnormally low production of metabolites, resulting in damage to lung tissue by respirable bacteria and dusts, or an abnormally high production, resulting in direct damage to lung tissue by metabolites themselves."

Jan 1, 1989

By H. B. Cooke

In connection with its researches on the crude petroleums of the United States, the Bureau of Mines has made a particular study of apparatus for the distillation of hydrocarbon mixtures. While this study is still incomplete it has already resulted in the development of considerable laboratory and semi-plant equipment, motet of which has been described in various publications of the Bureau. The laboratory apparatus (Hempel distillation) and method gives satisfactory comparative results in the laboratory examination of crudes and have been found applicable to crudes of all types, but the agreement of laboratory and plant distillations is not as close as might be desired. This is due, in part, to limitations in size and construction of the laboratory apparatus. Some refiners claim that the Bureau of Mines' laboratory method (Hempel distillation3) for distilling crude petroleum, does not show the full gasoline content of the oil, while others have stated that it indicates more gasoline than can be obtained from the crude commercially. This difference of opinion among refiners results largely from the great variation in stills used and methods of operating them. The Bureau's experience has shown that crude oils from different fields vary widely in character; in fact, that it is not yet possible to classify crude's adequately on the basis of their Down chemical and physical characteristics. As a result of the differences that exist among crudes, and of the difficulty of designing refinery equipment, no standard practice has yet been adopted for the commercial distillation of petroleum, and ma" types of stills are used in the refineries of this country. Although many factors enter into the design of equipment and the development of commercial practice in refining of crude oil, there

Jan 1, 1924

By H. M. Lawrence, E. Roca

"INTRODUCTION Of the phosphate rock deposits of the United States that are being exploited actively at present, the land-pebble area in Florida is the largest producer. In recent years the land-pebble district, in Polk and Hillsborough Counties, has produced about 80 per cent of the raw phosphate rock that has supplied the requirements of the several national industries based on this essential commodity.In the land-pebble deposits sizes finer than 16 to 22 mesh are below the commercial limit in phosphate content, and washing-plant practice has been directed to the recovery of the coarser material. Recently, more extensive control of the washery plan has resulted in the saving of additional amounts of phosphate, the loss of which had been considered unavoidable. However, strict requirements of the trade regarding the lowest acceptable grade of phosphate rock prevent the inclusion of more than a very small proportion of the low-grade phosphatic sands with the washery output of phosphate roe:. Further advances in practice resulting in larger recoveries of phosphate can only be effected by the application of processes that are based on other principles than merely a difference of particle size. Research is be conducted actively along these lines by the industry and by cooperating agencies.Flotation has been studied for several years by the International Agricultural Corporation and its allied company, the Phosphate Recovery Corporation. J. T. Burrows, vice-president of the International Agricultural Corporation, in a letter dated July 10, 1929, states:"

Aug 1, 1931

As part of the United States Department of the Interior, Bureau of Mines Health and Safety Research Program, Walter C. McCrone Associates, Incorporated has examined 71 samples of airborne mine dusts using the techniques of x-ray diffraction, electron microprobe analysis and light microscopy. This report details the procedures which were used in this work and documents the results which were obtained.

Jan 1, 2011

Provide the U.S. mining industry with a user friendly computer program to calculate stresses in underground coal mines in order to improve safety conditions for mine workers. Capabilities of MULSIM/NL MULSIM/NL (multiple seams, nonlinear) is a three-dimensional boundary-element method (BEM) program developed at the U.S. Bureau of Mines for stress and displacement analysis of coal mines. It can analyze one or two parallel seams that can have any orientation with respect to the Earth's surface. Three main new features distinguish MULSIM/NL from its predecessors: (1) non¬linear material models, (2) multiple mining steps, and (3) energy release and strain energy computations. MULSIM/NL has six material models for the in-seam material: (1) linear elastic for coal, (2) strain softening, (3) elastic plastic, (4) bilinear hardening, (5) strain hardening, and (6) linear elastic for gob. The multiple mining step capability enables the user to efficiently simulate a changing mine geometry. Finally, MULSIM/ NL computes energy release rate due to mining using the most recent concepts advanced by Salamon.

Jan 1, 1993

By Horst Peter Wölfel

The goal of biodynamic models is to simulate the vibration behaviour of the human body. In combination with experimental studies biodynamical models can be a powerful tool for the analysis of the effects of vibration exposure on health [1] and comfort. This paper gives an overview of the state of the art of biodynamic whole-body vibration models of humans, addressing both numerical models and hardware dummies. Method Two approaches are distinguished, the phenomenological and the anatomical, as illustrated in Figure 1. [ ] Phenomenological models aim to reproduce the vibration behaviour of humans with respect to particular physical quantities, chiefly the driving-point impedance at the interface to the seat, and partly with respect to other transfer functions. Discrete systems of masses, springs, and dampers with several degrees of freedom whose topology and parameters are determined by structure- and parameter identification methods are used in the sense that the functions derived from measurements are reproduced as well as possible. This paper provides an evaluation of this methodology and defines its range of application as well as its limits.

Jan 6, 2006

By Avery H. Reed

RECORD production of marble, kaolin, scrap mica, and talc high-lighted the mineral industry of Alabama in 1962. Among the States, Alabama ranked second in scrap mica, third in the production of bauxite and native asphalt, and fifth in iron ore. The mineral industry of Alabama was dominated by mining and processing of coal and iron ore, and the manufacture of cement, which together comprised 73 percent of the total value of production, compared with 72 percent in 1961. Other important industries were the production of crude petroleum, and stone quarrying. Leading companies were Tennessee Coal & Iron, Southern Cement Co., Southeastern Electric Generating Co., Alabama By-Products Corp., and U.S. Pipe & Foundry Co.

Jan 1, 1963

By Mark R. Pettitt

After a long series of laboratory and in-mine tests, a cost- effective, mineworthy, reduced-noise auger miner cutting head was de signed, fabricated, and field-tested by Wyle Laboratories under contract to the Bureau of Mines. Compared with standard auger cutting heads, the new heads reduced noise by 10 dBA at the jacksetter's position and by 6 dBA at the operator's position. This report contains detailed fabrication instructions, including engineering drawings, that show how a standard auger cutting head can be modified to produce a reduced-noise auger.

Jan 1, 1984