Search Documents

By James W. Miller

An investigation was begun by the Bureau of Mines in 1948 to determine the preparation characteristics of American coals. Results of the investigation were planned to be reported on a county basis and from the data developed, to determine: (a) Which coals either as mined or after beneficiation by conventional preparation are chemically suitable under present standards for producing metallurgical coke; (b) Which coals require special and more intensive treatment in preparation than is now practiced; and (c) Which coals cannot be considered potential sources of metallurgical coke, regardless of preparation. This report is one in this county series that describes the preparation characteristics of the coals of Perry County, Ky.

Jan 1, 1956

By Alan G. Mayton

Exposure to whole-body vibration (WBV) and the postural requirements of the job have been identified as important risk factors in the development of musculoskeletal disorders of the back among workers exposed to a vibratory environment. This paper focuses on preliminary results of WBV data collected for two groups of haulage trucks ? four older trucks from manufacturer A (MFR-A) and two newer trucks from manufacturer B (MFR-B). All of the trucks and their respective seats were considered to be in good working order during the study. Measurement periods for the truck groups had similarities, but varied from 2 to 58 minutes. Sampling times for the older trucks included a mean of 19.5 minutes and a standard deviation (STD) of 6.5 minutes compared to a mean of 40.8 minutes and a STD of 12.1 minutes for the newer trucks. Data collection coincided with the approximate delivery and first operation of the new trucks, and occurred approximately 12 months apart under similar weather and road conditions, and with the same drivers except an additional driver was included with the older trucks. Truck routes were somewhat different in that quarry production had changed location in the time between data collection activities. Overall, the results suggest that the newer trucks may provide better overall isolation to drivers/operators from WBV exposure compared to the older trucks operating at the quarry; although, this will need to be confirmed with additional measurements. Considering the higher variability and shorter sampling times for the older trucks, the results should be viewed with caution. For two of seven trials, the older trucks showed that seats amplified vibration, i.e., a transmissibility (T) >1.0. Seat T for the older trucks ranged from 0.31 to 1.17 with a mean of 0.77 and STD of 0.32. This contrasted with the newer haulage trucks where seats amplified vibration in 3 of 8 trials. In this case, T did not vary greatly and ranged from 0.87 to 1.05 with a mean of 0.97 and STD of 0.07. Regarding older trucks, in five of seven trials, the seat (output) data of weighted root-mean square (RMS) acceleration (wRMSZ) for the dominant z-axis exceeded the action level of 0.5 m/s2 action level recommended by the European Union Good Practice Guide for WBV (EUGPG) and levels exceeded the recommended exposure limit of 1.15 m/s2 in two of the seven trials. The wRMSZ values for the older trucks varied from 0.41 to 1.83 m/s2 with a mean of 0.99 and STD of 0.57. Similarly, newer trucks indicated a narrower range of wRMSZ from 0.38 to 0.95 m/s2. The mean wRMSZ was lower for the newer trucks at 0.58 m/s2 with a STD of 0.23 m/s2. Similarly, newer trucks indicated wRMSZ reached or exceeded the action level in four of eight trials. None of the trials with the new trucks showed wRMSZ levels that reached or exceeded the recommended 1.15 m/s2 exposure limit. As an indicator of driver/operator discomfort, overall weighted total RMS acceleration (vector sum) values seem to show a ?rougher? ride for the older trucks. The vector sum values for these trucks ranged widely from 0.70 to 2.59 m/s2 and, in four of seven trials, showed levels greater than 1.40 m/s2. The mean vector sum was 1.44 m/s2 with a STD of 0.75 m/s2. Comparatively, the newer trucks exhibited less variation with a range from 0.69 to 1.59 m/s2. The mean vector sum was 1.02 m/s2 with a STD of 0.35 m/s2. Vibration dose values for the dominant z-axis (VDVZ), gave a sense of vehicle jarring/jolting conditions. All trials with the older trucks were within the recommended EUGPG action level of 9.1 m/s1.75. On the other hand, in three of eight trials, both newer trucks exceeded this action level with values of 9.18, 12.58, and 13.21 m/s1.75. Neither truck group showed VDVZ that exceeded the exposure limit of 21 m/s1.75. A statistical analysis was not conducted, since the differences reported between truck groups may not be statistically significant owing to the relatively small sample size. Road conditions, changes in the truck routes, and driver/operator differences (e.g., stopping and turning) are possible factors in the higher VDV for the newer trucks.

Jan 1, 2008

By F. E. Cash

Among petroleum refinery employees and officials throughout the United States there has been marked effort to reduce accident frequency and severity. For the interest and benefit of refineries both in Louisiana and in other petroleum-refining States it has been possible to obtain from five refineries, representing 70 per cent of the production of Louisiana, tae accident experience for the past 3 to 6 years. The companies concerned have requested that their names be not used. For tide reason the four plants listed and discussed are designated as refineries A, E, C, and D. The size of the plant as regards largest to smallest number of employees is indicated by the alphabetical order.

Jan 1, 1933

By I. AITKENS

The basic mining law of Cuba is contained in the basic Spanish mining decree having the effect of law December 29 , 1868. This legislation has remained substantially unchanged , with the exception of a few minor administrative changes made by the present Government . These changes provide for the register of mines , oil wells , and operations of such nature , and also provide for the keeping of records showing the value of minerals taken out . By Royal decree of April 17 , 1883 , the law of mines enacted for the Peninsula ( Spain ) on July 6 , 1859 , and the General Bases of December 29 , 1868 , were declared in force in Cuba . In order to encourage the mining of iron org , in 1883 the Crow of Spain issued a royal decree to the following effect.

Jul 1, 1931

By W. E. Anable

The Bureau of Mines studied the purification of commercially available vanadium in the 100-kw electron-beam furnace. Purification studies were conducted on a 100-gram button scale by melting and holding the liquid vanadium at temperatures ranging from 2,060° to 2,080° C at pressure of 5(10)-5 torr for periods ranging from 5 to 20 minutes. The effect of doping vanadium with carbon and metallic additions was determined. This study demonstrated that hydrogen was readily removed to 3 ppm or less, oxygen and carbon were reduced to less than 100 ppm each, and the metallic impurities were reduced Co the range of 10 to 500 ppm. The nitrogen content was not reduced in any of the buttons; rather, the nitrogen concentration generally increased as samples were held for successively longer periods. Oxygen was removed much faster and more completely when vanadium was doped with small carbon additions or one of several dopes prior to melting.

Jan 1, 1967

By D. Bienstock

A rig was constructed to burn 100 to 125 lb of coal per hour at 4,000° F in a cyclone burner with oxygen-enriched air preheated to 1,500° F to ascertain the problems in the coal-fired MHD generation of power. Potassium carbonate was added to the coal at several concentrations up to 1.23 g-moles/kg of coal (17 lb K2C03/100 lb coal). Boiler-tube materials maintained at wall temperatures of 800° to 1,500° F were exposed to the combustion effluent of 1,800° to 2,500° F. Practically complete removal of sulfur dioxide from the stack gas was achieved with the seed addition. Nitric oxide formation followed theoretical expectations at combustion temperatures with some decomposition of the NO occurring as the gas cooled flowing through the system. Nitrates in the fly ash were less than 1.7 percent of the total fixed nitrogen. With aqueous extraction of the fly ash a maximum recovery of 75 percent of the potassium was obtained. Haynes 25 was unattacked at a wall temperature of 1,500° F in combustion gas at 2,500° F; the stainless steels 310, 316, and 446 were resist-ant at a metal temperature of 1,100° F in gas at 2,100° F.

Jan 1, 1970

Provide a simple and effective means of measuring mining-induced pressure changes in coal mine roof and pillars. Approach Develop a reliable, easy to fabricate and install borehole instrument which measures mining-induced pressure changes in pillars and in the mine roof. Ground pressures are monitored through use of aluminum platens coupled with d copper flat jack. How It Works The Bureau's instrument measures mining-induced pressure changes by transmitting strata pressure through the aluminum platens to an oil-filled borehole platened flat jack (BPF). Pressure in the flat jack is displayed on a gage located outside of the borehole. The instrument is in-stalled in the borehole by inflating the flat jack using a hand-held hydraulic pump. In addition, the platens have been designed to allow up to three BPFs to be installed in a single borehole, thus permitting pressure change measurements in more than one direction from a single borehole. Installation pressure is calculated on the basis of the estimated pressure exerted by the overburden and the percent of recovery after intial mining has

Jan 1, 1986

By Wils L. Cooley

Several aspects of coal mine safety-ground system operation are studied. Evaluations of two sophisticated ground-wire monitors are presented, along with a detailed report of development work on a modular ground-wire monitor. A portion of the report covers stray current flow in the safety-ground system, analyzing in detail conditions surrounding the generation of both dc and ac ground wire current. Considerable detail is provided concerning studies of mine ground beds. Additional progress is reported in the development of a. continuous ground-bed monitor, and new techniques are developed for the design of ground beds and their resistance measurement. New methods of accurately measuring electrical parameters of finite layered conducting structures are also reported. The effects of stray currents in ground beds is included. Touch-and step-potentials associated with mining equipment are analyzed, and methods are presented for determining earth voltage gradients around structures contacting earth. Instrumentation to determine gradients easily is suggested. Finally, an extensive effort is described dealing with lightning transients on open-pit coal mine ground systems. The nature of the transients, their expected frequency of occurrence, and the ways in which they damage equipment are analyzed in detail.

Jan 1, 1977

By G. W. Grove, G. L. FreAS

One of the chief hazards in mining bituminous coal is the accumulation of coal dust in the mines . When coal dust is thrown into suspension , it can be ignited and exploded by electricity through short -circuiting of mining machinery and trolley wires , or by arcs and sparks . The Bureau of Mines has endeavored to assist the coal -mining industry in preventing disasters from this cause by urging that all bituminous -coal mines be rock -dusted . As it has been difficult to convince some mining men of the danger of ignition of coal dust and of the effectiveness of rock dusting in preventing widespread explosions , a small , portable , coal -dust - explosion gallery has been designed to demonstrate the explosibility of bituminouscoal dust . Such galleries are furnished to Bureau engineers , inspectors , and safety instructors to illustrate visually and impressively the Bureau's accident -prevention educational work on the causes and prevention of dust explosions in bituminous -coal mines .

Jun 1, 1949

By D. E. Shanks

As part of its program to lessen dependence on foreign bauxite as the Nation's primary source of cell-grade alumina, the Bureau of Mines is investigating sulfuric acid (H2S04) leaching procedures for the recovery of alumina from domestic aluminous materials. The successful application of a H2S04 leaching process depends on the recovery of the aluminum values in an easily washed and filtered form, containing a minimum of water to be driven off in the subsequent calcination step. This goal was met by the high-temperature hydrolysis of simulated aluminum sulfate [A12(S04)3] leach liquor. Crystalline, insoluble aluminum hydroxy sulfate [A1(OH)S04], which had a water-to-alumina mole ratio of 1:1, was produced. Eighty-six percent of a solution containing 127 g of A12(S04)3 per liter and 76 pct of a solution containing 336 g of A12(S04)3 per liter were hydrolyzed to insoluble aluminum hydroxy sulfate by autoclaving for 1 hr at 320° C and rapidly quenching to room temperature. Higher operating temperatures were precluded by corrosion of the autoclave. The yield of aluminum in the hydrolysis product increased with increasing hydrolysis temperature and decreasing A12(S04)3 concentration.

Jan 1, 1981

By C. Gary Reiness

A safety glass eyepiece which had been repeatedly exposed to mine environment over a number of years was studied to determine some of its optical properties. In the regions from 385 to 400 mµ and from 625 to 760 mµ, the transmittance was less than the 89 percent required by the American Standard Safety Code for Head, Eye, and Respiratory Protection. From 200 to 320 mµ the relative transmittance of two parts of the eyepiece was found to vary widely, having a maximum of 38 percent difference at 315 mµ. Irradiation of the glass by ultraviolet light caused enhanced absorption in the range from 200 to 1,200 mµ. There was a time-dependent increase of 1016 color centers per cubic centimeter throughout this range after 36.5 hours of irradiation. The rate-of-growth curve for the optical density, at 243.5 mµ and 23° C, was resolved into linear and saturable components, indicating zero order and first order

Jan 1, 1968

By George L. Gates

The Bureau of Mines studied pressure-buildup data from a number of California gas wells to determine if the reservoir properties calculated from these data correlated with field-observed reservoir properties. Pressure-buildup curves from 24 wells showed distinct changes in slope, indicating changes in permeability of the reservoir rock. Calculated distances from the wells to indicated permeability changes were in fair agreement with distances deter-mined in the field. Pressure-buildup curves from three wells had more than one distinct change in slope, indicating multiple permeability changes. Thus field data supported the theoretical relations used to calculate reservoir properties from pressure-time relations measured in gas wells.

Jan 1, 1967

By Robert H. Ridgway

This paper presents the results of the second in the series of annual canvasses on the consumption of ferrous scrap and pig iron in the United States, inaugurated in 1935 by the Bureau of Mines and published in Report of Investigations 3329. The study was undertaken in response to requests from trade organizations and others for detailed statistics on this phase of the iron and steel industry. Thus, for the first time, producers, buyers, sellers, and consumers of iron and steel scrap have had an accurate statistical picture of this important raw material As originally contemplated, the study was to be continued on an annual basis, but, owing to budgetary limitations for the fiscal year 1937-38, the Bureau may be unable to conduct the canvass for 1937.

Jan 1, 1937

By J. J. Demeter

As part of its work on converting coal to fluid fuels, the Federal Bureau of Mines has been studying the synthesis of liquid fuels from carbon monoxide and hydrogen by Fischer-Tropsch synthesis. A fluidized bed of nitrided, fused-iron catalyst has been operated successfully to produce high yields of oxygenated compounds. Trouble-free operation continued for over 800 hours, and the test was terminated voluntarily. About 85 percent of the fresh feed was converted when the unit was operated at a space velocity of 500 hr.-1, a 12:1 recycle-to-fresh-feed-gas ratio, a 300-p. s. i. g. pressure, and a temperature of 252° C. When operating at a fresh-feed-gas space velocity of 1,000 hr.-l and a 9:1 ratio of recycle to fresh gas, conversion of fresh feed was 68 percent, and the product yield was 235.9 grams per cubic meter of synthesis gas converted. The oxygenate and C5 and heavier hydrocarbon yield was 110.6 grams per cubic meter of gas converted, 83 percent of this was oxygenates. The atom ratio of N:Fe of the catalyst, initially 0.455, decreased to 0.288 by the end of the 800-hour experiment. Nevertheless, the yield of oxygenated compounds per cubic meter of H2 + CO converted at the end of the run was approximately the same as that obtained 500 hours earlier with identical operating conditions. X-ray analysis of the discharged catalyst indicated that only ?-iron carbonitride was present. Sieve analysis of the discharged catalyst indicated that only 2 percent of fines was produced during the reduction, nitriding, and synthesis.

Jan 1, 1959

By W. G. Payne, A. C. Richardson, B. L. Gandrud

"INTRODUCTION The Connellsville mine of the Yolande Coal & Coke Co. is in the southwestern part of Jefferson County, Ala., about 30 miles southwest of Birmingham. The mine is on the Blue Creek bed, which is about 6 feet thick and dips at a angle of 18º. The bed is worked by the room-and-pillar method and is mined by both machine and hand methods. The Blue Creek bed at this point yields a high ash, low-volatile coal with excellent coking properties. Because of its exceptionally low volatile content and high coking strength, this coal is excellent for blending with Alabama coals of higher volatile content and weaker coking properties to form blends suitable for production of metallurgical coke.A sample of washed coal taken during this investigation gave the following analysis on an as received"" basis: Moisture, 8.3 per cent; volatile matter-, 20.2 per cent; ash, 8.0 per cent; fixed carbon, 63.5 per cent. The high ash content of this coal limits the quantity which can be utilized when low-ash coke is required. In the Birmingham district it is usually difficult to sell as coking coal a product that contains more than 8.0 per cent ash. To produce a. coal with this ash content at Connellsville presents a somewhat difficult washing problem. This paper gives the results of an investigation that was conducted by the Southern Experiment Station of the U. S. Bureau of Mines in cooperation with the University of Alabama and the Yolane Coal & Coke Co. for the purpose of determining the washing characteristics of the coal and the possibility of reducing its ash content on coal-washing tables.The practice at the Connellsville washery at the time of beginning this investigation was to crush the run-of-mine coal to pass a 1 1/2-inch round-hole screen and to treat the satire output on two primary, 3-compartment jigs. A. middling product was recovered from the primary jigs which was re-treated on a single-compartment rougher jig. This system yields a product of acceptable ash content, but the yield is low and the loss of good coal in the refuse is high."

Feb 1, 1933

By R. V. Ramani, A. S. C. Owili-eger

The quantity of methane emitted into the mine atmosphere and the movement of gas through solid coal and the adjoining country rock are dependent on the physical properties of the medium, boundary con¬ditions, the initial gas pressure distribution, and the combination of natural and mining factors. Functional relationships between these factors are not yet known. Consequently, the development of rigorous mathematical models to predict methane flow into the mine air is difficult and to date no model has been reported which is capable of such a function. Thus far, empirical formulas available for the calculation of gas quantity released from underground sources require too much his¬torical data, not currently available. Again, these estimations are at best only crudely approximate. The numerical methods available have not been made practical enough for industry wide application. Therefore, the development of a relationship amenable to numerical analysis and practical enough for use in the industry would provide the flexibility lacking in analytical approaches. The mathematical models given in equations (7) and (8) are further attempts in presenting practical models for predicting the quantity of methane emission into the mine environment. Equation (7) is the steady state model and equation (8) is the unsteady state model.

Jan 1, 1974

By James L. Ash

This report contains the results of a technical and economic evaluation of conceptual systems for the underground mining, rubblization; and in situ retorting of deep oil shale deposits. Study efforts were first directed towards evaluation of the applicable geology, associated minerals, rock mechanics, in situ retorting, access mining, ventilation, rubblization, safety, and environmental impact factors. Conceptual systems were synthesized and then evaluated against these factors from both a technical and limited economic viewpoint. The results of these evaluations were then analyzed 'and, based upon this analysis, the following two systems were selected for further study: System II: Room and Pillar-Vertical Drill and Blast System IV: Tunnel Boring-Horizontal Ring Drill and Blast Due to the large number of variables to be considered, a computer program was developed and utilized to provide data for the cost trade-off studies and economic analysis. Results of the early computer runs indicated the value of the tool available in the computer program and led to an extension in the contract to determine the sensitivity of the systems to several of the more apparent significant variables. These results in turn led to a refinement in the design assumptions and a better understanding of the technical and economic options available to an owner-operator of a Vertical Modified In Situ Shale Oil Extraction System. This report is submitted in fulfillment of the requirements of Contract Number S0241073 by Fenix & Scisson, Inc. to the Denver Research Center, United States Department of the Interior, Bureau of Mines. Work was completed as of November, 1976.

Jan 1, 1976

By J. G. Linn, H. H. Schrenk, W. P. Yant, R. R. Sayers, John Chornyak, F. A. Patty, S. J. Pearce

"This report is the first of a series dealing with the results of a comprehensive investigation of methanol poisoning, conducted jointly by the Federal Bureau of Mines, Carbide & Carbon Chemicals Corporation, du Pont Ammonia Corporation, and the Commercial solvents Corporation.The study dealt mainly with physiological effects produced by inhalation of methanol vapor, and concentration studied ranged from approximately 500 to 15,000 p.p.m., and periods of exposure from 4 hours daily to continuous. The range of concentrations and periods of exposure were such as to produce acute effects, with and without fatalities, by a singel exposure and chronic poisoning, with and without fatalities, as well as little or no response after repeated daily exposures. In addition to the inhalation experiments, skin absorption was studied, and field surveys were made to ascertain the hazards associated with the manufacture and, use of methanol."

Feb 1, 1942

By Frank A. Peters

This evaluation of the sulfurous acid process for the production of metallurgical-grade alumina is the first of a series concerning various known methods of extracting alumina from low-grade aluminous materials and was undertaken to permit comparison with other processes. In the process with which this Bureau of Mines report is concerned, calcined clay is leached under pressure with 20 percent sulfurous acid and then filtered to remove a siliceous residue. The aluminum sulfite remaining in the filtrate is precipitated as a monobasic sulfite which, together with iron sulfite, is then decomposed under pressure to form a crude alumina hydrate and iron oxide. This intermediate product is purified in a modified Bayer process to yield alumina suitable for electrolytic reduction to aluminum. A study estimate (16)3 is used for these evaluations. The capital cost, not including land, is estimated at $95,701,600 on a Marshall and Stevens index basis of 240.0 for a plant producing 1,000 tons a day of alumina or 350,000 tons a year. The annual operating cost for this size plant is estimated at $22,831,100 or $65.23 per ton of alumina using clay at $1 per ton. Depreciation and local taxes are included in the estimate, but profit and Federal taxes are not considered.

Jan 1, 1962

By Wing G. Agnew, Albert E. Long

"SUMMARY AND CONCLUSIONSTests conducted at Mount Weather indicate that clear water is the best bit coolant and cuttings-removal medium for diamond drilling. All of the mediums tested did show that drilling speed increased when drilling with the faster feed ratios (greatest pressure on the bits). In no case, how¬ever, did the increased drilling speed amount to over 16 percent, and even in a long hole the slight increase in drilling speed would be more than offset by the extra time consumed in setting up.Bit wear was excessive when lubricating agents were used, the most footage per bit was obtained when drilling with clear water in the normal manner, and the next best footage was obtained when drilling with circulated water containing no lubricating agent. The diamonds showed little or no wear in any of the bits, and all bits cut well throughout the tests. They were only taken out of service when erosion of the cast metal had progressed to the point where the diamonds were about to roll out. The lubricating agents evidently hold some of the cuttings in suspension, which in turn help to cut the rock but also wear the metal of the bit.No hard-matrix bits were tested, and it is possible that one or more of the lubricating agents might increase the efficiency of such a bit by keeping it sharp and doing away with the necessity of sharpening by sand blasting. Some tests are planned with hard-matrix-type bits and the same lubricating agents used in the tests under discussion, but it is realized that any drilling advantage gained by the bits sharpening themselves may but at least partly offset by excessive wear of the Pump parts."

Jan 1, 1945