Search Documents

By A. J. Kraemer

This report on the physical and chemical properties of typical crude oils of California is the 'eighth in a series on the producing districts of the United States. It includes discussion of results, tabulated data, and individual analyses of typical California crudes. Additional analyses of crude oils from the fields of Fresno, Kern, Los Angeles, Orange, end Ventura Counties will be published later in another Serial of the Bureau, but the summary tabulations are presented here. The samples represented in this report were collected over a rather wide interval of tine, the early samples having been obtained during the fall of 1919, and the most recent ones dating from the summer of 1923. It is thought that the samples are fairly representative, both of the older settled production and of the new flush production of the southern California fields.

Jan 1, 1924

By W. M. Merritts

The control of coal dust created and released during the operation of continuous mining machines in bituminous-coal mines of the United States is a problem. The interest manifested in this problem indicates the seriousness of the hazards involved, particularly when the dust has not been abated at its source and has become air-borne. Officials of the Sunnyside No. 1 mine, Kaiser Steel Corp., were confronted with the problem of abating the coal dust created by operation of a recently installed continuous-mining machine, and they requested the aid of representatives of the Coal-Mine Inspection Branch, Bureau of Mines, United States Department of the Interior, in developing an effective method of allaying the coal dust at its source.

Jan 1, 1951

By G. M. Molinda

The U.S. Bureau of Mines conducted an investigation to determine the nature and frequency of coal mine roof failure beneath valleys. A mechanism for this failure and suggestions for controlling this problem are presented. Hazardous roof conditions identified in some mines were positively correlated with mining activities beneath stream valleys. Mine maps with overlays of unstable roof and locations of stream valleys show that 52 pct of the instances of all unstable roof in the surveyed mines occurred directly beneath the bottom-most part of the valley. The survey also showed that broad, flat-bottomed valleys were more likely to be sites of hazardous roof than narrow-bottomed valleys. Evidence of valley stress relief was found beneath several valleys in the form of bedding plane faults and low-angle thrust faults. This type of failure, previously believed to be only a shallow phenomena, was found at mining depths as great as 300 ft. In situ, horizontal stress measurements beneath a valley and the adjacent hillsides, confirmed valley stress relief. Numerical analysis of 13 valleys overlying one mine property showed the effect of the valley excavation on horizontal and vertical stress.

Jan 1, 2010

By R. V. Lundquist, H. Leitch

Sodium aluminate is the principal aluminum compound formed in the sinters prepared by the lime - soda sinter process for recovering aluminum from silicate source materials . The properties and characteristics of this compound were studied to improve the efficiency of the process . Crystalline sodium aluminate was prepared by sintering stoichiometric quantities of soda ash and calcined alumina for 1 hour at 1,250 ° C. The extent of aluminum extraction from sodium aluminate was determined in water and in solutions of NaOH and Na₂ CO3 . Nearly complete extraction of aluminum from sodium aluminate was achieved only in solutions containing free NaOH in excess of that supplied by the salt through hydrolysis . About 42.2 to 68.8 percent of the aluminum was extracted in water or in solutions of Na₂ CO . The precipitation of alumina trihydrate from sodium aluminate solutions was shown to be part of a continuous , reversible reaction according to the equation Al (OH ) A1 (OH )3 + OHThe reverse reaction dissolves alumina trihydrate in NaOH solutions to produce sodium aluminate . Approximate equilibrium concentrations were determined for the reaction at 30° , 50 ° , and 70 ° C. False apparent equilibrium conditions for the dissolution reaction appear when only a small excess of alumina trihydrate is present in the NaOH solutions . A large excess of alumina trihydrate must be present before the true equilibrium point is assured . The engineering significance of the data is summarized , showing controls that should be exercised for a successful and efficient process .

Jan 1, 1964

By W. R. Reed

Drilling with water has the potential to significantly reduce the respirable dust concentrations generated from small-diameter rotary drills when drilling blastholes on surface mining operations. However, water adverseky affects tri- cone drill bits commonly used in surface drilling operations, causing excessive wear and premature replacement. Consequently, dry drilling with a dust collector system has the most widespread use in the industry. Tests have been conducted by the National Institute of Occupational Safety and Health (NOSH), Pittsburgh Research Laboratory (PRL) on a newly designed device for smaller diameter drills that separates the water from the bailing air before it reaches the bit and thus provides the cost benefit of dry drilling while providing the benefit of wet drilling for dust suppression. The water that is delivered to the hole with the bailing air is separated from the air by a proprietary mechanical device that is encased in a drill sub (short section of drill rod/pipe) located immediately behind the cutting bit. A cascade cyclone and a real-time dust monitor were used to sample dust emissions from the holes. Dust concentrations and silica content were measured when drilling dry versus drilling wet. The tests show that drilling with this water separating sub can reduce both measured dust emissions from the boreholes and visible dust around the drill rig.

By James H. Snyder

This final report presents results of a program to develop a new conveyor system, adaptable to existing miners or loaders, which reduces the noise level to 90 dBA without reducing machine performance. The trial conveyor design consists of a main conveyor and a swinging tail conveyor. The main conveyor incorporates a rubber-covered return guide roller, rubber mounting of pillow blocks, rubber cover of the return bed, and a rubber belt running between the flight chain and the conveyor bed plate. Testing took place in a surface coal pit and underground at the Peabody Spur Mines in Boonville, Indiana. Noise Levels as low as 90 dSA were observed on the surface and 93/94 dRA underground. Recommendations for further work are also presented.

Jan 1, 1976

By L. Cheng

This report describes a laboratory investigation of the effectiveness of low-pressure steam and a steam-water spray sequence for the collection of airborne respirable (<10 µm) coal dust. Comparison of present results to previous results obtained with water spray alone indicates that the use of steam in a steam-spray sequence increases the collection efficiency by about 14 percent over that obtained by water spray alone. However, the use of steam to collect airborne dust requires cooling the steam-dust mixture in order to achieve condensation of the steam, and steam does not appear to be an attractive approach for collecting airborne dust in underground coal mining operations.

Jan 1, 1974

By Oliver Bowles

"The American Consul at Guatemala City reports that the Guatemala Marble Mining Company is preparing to operate a marble quarry about 13 miles from the railroad station of Zacapa, which station is a little over 100 miles from Puerto Barrios, the nearest port from which the product may be shipped. The deposit is extensive, and though somewhat broken up in places, great quantities of sound marble are available. It is claimed that the marble is equal in quality to the best product of the Italian Carrara quarries.Access to the quarry by rail is obtained by a spur track of the International Railways of Central America (Ferrocarril Internacional de Centro America) from Marmol, 3 miles south of Zacapa. This spur is about 5 miles long and terminates at the foot of the mountains. A double-track incline cable-way 2000 feet in length has been constructed to bring the marble down the mountain. From the top of the incline to the quarry there is a railway six miles in length over which the rock will be hauled by two side-geared Shay locomotives."

Mar 1, 1920

By Nicholas G. Theofilos

The Bahamian economy weathered the worldwide recession of the last few years better than most developing countries. This was mainly owing to the ties between the tourist industry of the Bahamas and the U.S. economy. The mineral industry played a minor role in the country&apos;s economy. The chief mineral exports included an increasing amount of petroleum products horn the country?s 500,000-barrel-per-day refinery, steel pipe, salt, and aragonite. A 60,001)-barrel-per-day desulfurization facility was completed by Bahamas Oil Refinery Co. (BORCO) in Freeport. The project included vacuum gas oil desulfurization, hydrogen and sulfur recovery, steam generation, water desalinization, and offsite facilities.

Jan 1, 1980

By Robert P. Bruno

This report covers the study of the feasibility of using a hand-held infrared viewer as a methane indicator to observe methane gas at the face of an underground coal mine. The objective of this program was the development of a hand-held device to remotely detect the presence of concentrations of methane gas in underground coal mines. Convenient "mapping" of methane from a remote location would allow rapid and safe corrective procedures for working personnel. Modified commercially available equipment was evaluated both in the laboratory and in a working mine. Although readings were obtained and the general principle of operation demonstrated, the power levels necessary, and protective enclosures required, would raise the weight of the instrument beyond practical limits of portability. Based on currently available technology, it is the conclusion of the investigations that a practical, portable, hand-held visual methane indicator is beyond the state-of-the-art. The recommendation was, therefore, made that work be suspended, and the results and data compiled and presented in a final program report.

Jan 1, 1979

By Mark R. Pettitt

The development of fire hazard criteria for noise control products in underground coal mines are presented. Qualifying requisites of the criteria include maintaining miners&apos; safety, allowing for maximum use of noise control products, and economic feasibility. The burning process is analyzed for its relationship to fire hazard criteria developed by NASA and the FAA, and the mine environment is analyzed in conjunction with the end-use applications of noise control products. Also, the interim fire hazard specification developed by MSHA is appraised as it applies to end-use applications of noise control products. From these analyses and a literature survey, fire hazard criteria are developed. They include an initial screening procedure that evaluates the level of flammability testing required. Fire tests that may be indicated are the Vertical Flame Test, the Ignition Temperature Test, and the 25-Foot Tunnel Test.

Jan 1, 1983

By R. M. Jimeson

Pressure-drop measurements through beds of granular iron, lathe turnings, steel wool, and parallel-plate assemblies were made at linear velocity and gas-density ranges expected in the Fischer-Tropsch hot gas recycle process.4/ Equations relating pressure drop, linear velocity, gas density, and bed porosity were derived. The results indicate that the exothermic heat of reaction can be removed at a lower cost by using catalyst beds with high porosity. INTRODUCTION The Fischer-Tropsch hot-gas-recycle process requires a catalyst offering low resistance to gas flow as one condition to economic feasibility. Conventional granular or spherical catalysts used during early development of the process in Germany did not meet this requirement. Large pressure drops across these beds made the cost of recirculating the gas excessive. The Federal Bureau of Mines is investigating the process by using novel and unusual catalysts that offer little resistance to gas flow. Pressure-drop measurements across these types of catalyst beds are discussed in this report.

Jan 1, 1959

By S. M. Shelton, M. M. Fine, T. L. Johnston

"INTRODUCTION The Bynum property is about 15 miles west of Gadsden and 1 mile north of Walnut Grove, Etowah County, Ala. The ore lies in layers and as irregular masses and pockets in the clay residue from decomposed quartzite and limestone formations to the district.The property has been developed by means of numerous shallow shafts sunk to water level - about 25 foot. Operations are confined to small-scale, selective mining of pockets of high-grade ore. The ore is marketed directly, without beneficiation. The property does not yield a large amount of manganese ores. No estimates of reserve ore tonnages are available.A 206-pound sample was furnished for test. It was taken at random from a stock rile estimated to contain 130 tons of ore. The sample con¬sisted of a mixture of manganese oxides, iron oxides, and siliceous fragments in clay. The manganese occurred largely as soft, unconsolidated pyrolusite and wad. Some hard, crystalline pieces of psilomelane were distributed through the soft material. Small amounts of iron oxides were associated with the manganese oxides. Chert, quartzite, and clay comprised the gangue minerals.Dry analysis of the sample was as follows: 36.0 percent manganese, 6.1 percent iron, 2: .0 percent silica, 1.5 percent calcium carbonate, 0.36 percent phosphorus, 3.0 percent alumina, 2.2 percent barium, and 0.31 percent zinc."

May 1, 1942

By E. H. Denny

This paper discusses accident experience and costs in 150 Colorado coal mines for the 5 years 1929-33; these mines produced 62 percent of Colorado&apos;s coal tonnage during this period. This and similar studies by the United states Bureau of Mines in other States (listed in the appendix to this report) make available comparable information on mine-accident costs and bring out clearly the importance of accident reduction from the humanitarian as well as from the economic standpoint. Compensation insurance costs constitute a considerable part of the cost of coal output. The tendency toward greater liberalization of workmen&apos;s compensation laws and increased benefits thereunder may mitigate to some extent the seriousness of an accident to a worker and his dependents, but no compensation is paid ultimately, not by an insurance fund but by the mine operator and the general public, which includes the miner. The one really effective method of reducing compensation costs is to reduce the number and severity of accidents.

Jan 1, 1935

By J. S. Walker

The Bureau of Mines monitored surface subsidence and water level fluctuations in 10 shallow observation wells above a series of four adjacent longwall panels in southwestern Pennsylvania, for about 4 yr. This study attempted to correlate the changes in the water levels within the observation wells to the measured vertical and horizontal ground movements associated with subsidence. Results of this study indicate that the fluctuation of the water levels appears to be a function of the well location relative to the mine layout and the proximity of mining. Wells are generally unaffected by mining of a preceding panel unless they are located within the angle of draw for that panel. Wells located at the centerline of a longwall panel exhibit the greatest fluctuation and head loss. This relationship may be related to the strain developed by the advancing longwall face. The water levels in the wells monitored fell at the greatest rate when the ground surrounding the well was in tension. The rate of the decline decreased as the dynamic development of the strains was changing from tension to compression. The water levels were found to be near the premining level before the ground was subject to maximum compressive strain. Nine of the ten wells investigated recovered to their premining water level after mining was completed.

Jan 1, 1988

By J. R. Cobble

The Federal Bureau of Mines conducted static tests at 2,500° F on 39 refractory compositions, and dynamic tests at [2,825°35° F] on 31 commercial refractory brick specimens to determine their resistance to corrosion and erosion by a slag similar in composition to that used in producing insulating mineral wool. The static tests showed fireclay, low-alumina compositions (<70 percent A1203), zircon, zirconia, SiC, and clay-bonded graphite refractories to be unsuitable. Dynamic test results indicated that magnesia and chromia compositions were superior to high-alumina compositions (=70 percent A1203) as a furnace lining for melting mineral wool. Data from these tests indicated that magnesia and chromia compositions with low RO/R203 mole ratios were more resis tant to attack by mineral wool slags than ones with high RO/R203 mole ratios.

Jan 1, 1975

By K. O. Bennington

The thermodynamic properites of petalite (Li2A12Si8O20) were determined by the Bureau of Mines. The enthalpy of formation was determined by hydro-fluoric acid solution calorimetry. The values from the elements and from the oxides are ?Hf°298.15 = 2,335.8 ± 3.0 kcal/mole and ?H°295 (from oxides) = -50.60 ± 1.20 kcal/mole. Low-temperature heat capacities were determined by adiabatic calorimetry from 10.69 to 302.11 K. The derived standard entropy is S°298.15 = 111.0 ± 1 cal/deg-mole. Enthalpy increments above 298 K were measured by copper block calorimetry from 298 K to 1,193.6 K. The various experimental data were combined with other data from the literature to calculate the Gibbs energies of formation and equilibrium constants of formation over the temperature range of the measurements. Tables of enthalpies of formation and Gibbs energies of formation are given as a function of temperature from the elements and constituent oxides. The Gibbs energy of formation is ?G°f298.15 = 2,203.8 kcal/mole.

Jan 1, 1980

By Marcia L. Harris

Toxic fumes produced by detonating explosives in surface mining and construction operations pose potential hazards to workers and the public. Blasting operations produce both toxic and nontoxic gaseous products; the toxic products are mainly carbon monoxide (CO) and the oxides of nitrogen (NOx). Since 1988, there have been 17 documented incidents in the United States and Canada in which carbon monoxide (CO) is suspected to have migrated through ground strata into occupied enclosed spaces as a result of proximate trench blasting or surface mine blasting. These incidents resulted in 39 suspected or medically verified carbon monoxide poisonings as well as one fatality. At worst people may be fatally poisoned and the least to be expected is increased public objections to blasting. Local and state agencies could demand a cessation of the blasting requiring more expensive mechanical means to break the rock. This paper discusses the most feasible means of preventing CO migration, mitigating CO that has migrated, and detecting CO in an underground enclosed space and may help reduce the exposure of unsuspecting area residents to carbon monoxide and help prevent the implementation of unnecessary regulations and limitations on blasting. Single-hole shots and small-scale multiple-hole blasts were performed that indicate promising means of prevention and mitigation.

Jan 1, 2008

By John Campbell, Miller. W. E., G. W. Jones

"INTRODUCTION Because of its interest in accident prevention, the Federal Bureau of Mines has cooperated with city officials and utilities in investigating the causes of explosions in sewers, manholes, and other underground spaces and has aided in the development of means to prevent such explosions. For several years this Bureau has cooperated with the Boston Edison Co. and the Boston Consolidated Gas Co. of Boston, Mass.,for the purpose of detecting and eliminating combustible and physiologically harmful gases in manholes in Boston and vicinity.These investigations 5/ have shown that combustible gases from the usual sources — leakage from gas—distributing systems and underground tanks and gasoline wastes — can be located and the dangerous conditions remedied by a well—planned, adequately supervised, systematic, and continuous manhole survey. However, other types of gas contamination, termed ""soil"" gases, are present in manholes at times and are more difficult to eliminate because they have no fixed origin and because seasonal and barometric chances affect their production and passage into the manhole. Soil gases usually are abnormally high in carbon dioxide and low in oxygen and contain varying amounts of methane. They are especially dangerous to men entering manholes because they lack sufficient oxygen to support life."

Feb 1, 1940

By Isaac A. Zlochower, Kenneth L. Cashdollar

The Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health conducted a study of the explosibility of various metals and other elemental dusts dispersed in air, with a focus on the experimental explosion temperatures. The data are useful for understanding the basics of dust cloud combustion, as well as for evaluating the explosion hazards in the minerals and metals processing industries. The dusts studied included boron, carbon, magnesium, aluminum, silicon, sulfur, titanium, chromium, iron, nickel, copper, zinc, niobium, molybdenum, tin, hafhium, tantalum, tungsten, and lead. The dusts were chosen to cover a wide range of physical properties - from the more volatile materials such as magnesium, aluminum, sulfur, and zinc to the highly "refractory" (very low volatility) elements such as carbon, niobium, molybdenum, tantalum, and tungsten. These flammability studies were conducted in a 20-L chamber, using strong pyrotechc ignitors. The experimental data obtained included the minimum explosible concentrations, maximum explosion pressures, and maximum explosion temperatures. A unique multiwavelength infrared pyrometer was used to measure the temperatures. For the elemental dusts studied, all ignited and burned as air-dispersed dust clouds except for nickel, copper, molybdenum, and lead. The measured maximum explosion temperatures ranged from -1 550 K for tin and tungsten powders to -2800 K for aluminum, magnesium, and titanium powders. The measured temperatures are compared to the calculated, adiabatic flame temperatures. In general, the dusts whose experimental temperatures were closer to the adiabatic values were those with the finer particle sizes, those that were more easily vaporized, and/or those that were intrinsically more reactive.