Search Documents

By Russell J. Foster

This Bureau of Mines review focuses on the extent to which technologically and economically feasible programs in substitution, improved processing practices, including recycling, and design can achieve conservation of cobalt, chromium, manganese, and platinum-group metals, and thus reduce U.S. vulnerability to interruptions of supply. In addition, supply-side options--domestic and foreign resources, ocean minerals, and stockpiles--are identified. The report consolidates four major studies on these strategic and critical minerals sponsored entirely or partially by the Bureau in the last few years. These studies have been updated with further information from the recent literature.

Jan 1, 1985

By A. J. Kraemer

For a number of years the Bureau of Mines has been conducting an investigation of crude petroleum from producing fields in the United States and the Western Hemisphere and has published a series of reports on these fields. Analyses of crude-oil samples tom some oil fields of Louisiana are given in Bulletin 291.4/ Analyses of 26 representative crude oils from various producing formations of southern Louisiana are given in is report. These.samples are from 14 field's in 10 parishes in the southern part of the State, usually designated as the "Louisiana Gulf Coast area." ACKNOWLEDGMENTS Thanks are due the representatives of the various companies from whom samples were obtained for their cooperation and assistance in helping to secure representative samples. The samples were analyzed under the direction of E. C. Lane at the Bartlesville station of the Bureau of Mines.

Jan 1, 1934

By Oliver Bowles

"The town of Monson in Piscutaquis County, Maine is the, center of an important site industry. Monson slate has a nation-wide reputation, particularly for electrical switch boards, and the deposits have been worked for the manufacture of such products for many years. Open-pit quarrying is the method most commonly employed in obtaining slate. Underground methods have been used in the Peaon Bottom district near Delta, Pennsylvania, but the quarries that were thus operated are now abandoned. Underground methods have been used more extensively in foreign countries, the most famous example being the slate mines at Angers in France, where an over-head stoping method has been employed successfully for many it is only under special conditions that underground methods can be successfully used. If the deposit is wide and relatively thin, or if the material is too unsound to constitute a safe roof, open-pit methods must be used, for slate is too low-priced a commodity to justify the heavy expense of any timbering methods. It is only where the deposit is relatively narrow, of great depth, and sufficiently sound to afford a strong roof that ordinary mining may be employed.The best slate beds in two of the three quarries operated at Monson are no worked by underground methods. The chief bed worked by the Portland Monson Slate Co. is 10 feet thick, stands vertical and strikes N. 63º F. The slaty cleavage is vertical and crosses the strike of the beds at an angle of 5 to 10°. The grain or second direction of splitting is vertical and perpendicular to the cleavage. In addition to the 10-foot bed, to 2-foot beds and one 5-foot bed are available but are not now utilized. In the Monson Maine Slate Co. quarry (the old Pond quarry),a greater number of beds available, but at present quarrying is confined to a single bed about 9 feet thick which dips 30º S.E. and strikes N. 47ºF. The slaty cleavage is vertical and strides N. 45º F., while the grain strikes N. 45-50º W. and is also vertical."

Nov 1, 1920

By Stephen A. Swan

This Bureau of Mines report discusses research to analyze and evaluate extended bumper systems in order to determine the degree of protection provided to equipment operators in the event of rear-end collisions be-tween off-road rear-dump haulage trucks. The basic characteristics of rear-end collisions were determined, and a detailed analysis of the col-lision dynamics was performed to identify the magnitude and direction of impact loads, the amount of energy that must be absorbed during impact, and the major factors that affect the outcome of a collision. Separate bumper designs were developed to facilitate attachment to four 170-st-capacity haulage truck frame types.

Jan 1, 1987

By John L. Thames

The benefits of water harvesting as an alternative to conventional reclamation were demonstrated on the Peabody Coal mines in Northeast Arizona. The project produced food crops for four years, and demonstrated that a catchment/crop area ratio of about 2.5:1 was sufficient to obtain sufficient water from the 11 inch annual precipitation to produce garden and fruit varieties in quantities equal to or exceeding national production averages. The economic returns exceeded those of the conventional practice of returning the mine area to rangeland by at least ten fold. Subsidence of the regraded spoil was the only major problem in maintaining the system. Although, water harvesting systems have the potential of providing high economic returns and greater social benefits, as demonstrated by this project they are presently at variance with the strip mining regulation.

Jan 1, 1984

By Sidney Katell

Covering the period from January 1961 through December 1961, this report is a continuation of the series that began with the publication of Information Circular 7516 in October 1949. It is also the third report in the series to be prepared as a cooperative effort by the Bureau of Mines and the American Association of Cost Engineers. The cooperative agreement between the two groups provides for the publication of an annual cost bibliography with the work load involved in the preparation shared equally. The abstracted articles, concerned with all facets of cost engineering in the field of chemical and petroleum plants and related facilities, came from the following sources: 1. A.A.C.E. Bulletin. 2. Bureau of Mines Information Circulars. 3. Bureau of Mines Reports of Investigation. 4. Chemical Engineering. 5. Chemical Engineering Progress. 6. Chemical Week. 7. Coal Age. 8. Coal Utilization. 9. Cost Engineering. 10. Industrial and Engineering Chemistry. 11. Nucleonics 12. Oil and Gas Journal. 13. Petroleum Engineer for Management. 14. Petroleum Refiner. 15. World Oil.

Jan 1, 1962

By Michael S. Miller

In 1984, at the request of Bureau of Land Management, the Bureau of Mines studied 8,500 acres of the 20,250-acre Seven Blackfoot Wilderness Study Area (WSA) consisting of all 3,950 acres of MT-024-657A and 4,550 acres of the 4,850 acre MT-024-657B in order to evaluate the mineral resources. Within this report these 8,500 acres are referred to as the study area. Located about 30 miles northwest of Jordan, MT, the study area is underlain by outcrops of Quaternary alluvium and Cretaceous to Paleocene sandstones, shales, clays, and coal. No mines or prospects were found in the study area. Except for some current interest in petroleum and natural gas, there has been no mineral exploration activity in the study area. The study area contains subeconomic clay, placer gold, and coal. Land within the study area is leased or under lease application for oil and gas.

Jan 1, 1986

By Patricia R. Devine

This appendix documents the mathematical approach to deriving the components of change presented in this report. The formulation closely follows that contained in Chapter IV of the documentation for the BEA 1977 Input-Output Tables.' The basic elements for the calculations include the "use" matrix (U), the "make" matrix (M), and any of the ten columns of final demand (generically represented by the symbol y). The use matrix contains information about changes in the technological processes of production, while the make matrix describes the nature of secondary product production in each industry. We adhere to BEA conventions in maintaining careful distinctions between commodity output (c) and industry output (x). The industry-by-industry 1-0 tables supplied by NYU for use in this analysis are square matrices, with the number of commodities and the number of industries both equal to 85. The BLS table for 1982 (commodity by industry) was aggregated and adjusted to be consistent with the earlier tables. The three basic steps for estimating components of change proceed as follows for each column of final demand. 1) Calculate the actual change in output of each commodity for each of the four time periods: 1963-72, 1972-77, 1977-82, and 1963-82.

Jan 1, 1988

By T. T. Read

"Education is the one thing which is unanimously regarded as valuable. The growing complexity of modern life, with its intricate organization, the manifold kinds of mechanical equipment that are used, and the constantly growing, necessity for the speedy and accurate interchange of information and ideas, make education an asset that constantly increases in value. The number of things that may profitably be known has grown so large that the field of education has been divided, and attention is often directed to only those things that are most immediately valuable. Modern educational facilities are often directed to what may be called corrective, work; the, providing of people with information that they teed in the conduct of their daily lives, but which for various reasons they have not previously had facilities for acquiring. The value of special education in the industrial world has been so thoroughly demonstrated that far-seeing managers of mining enterprises are always interested in the educational facilities existing in the community where their work is carried on.The educational facilities of a modern community may be classified in several ways. They may be divided into;1. Facilities for general education, for the purpose of increasing the whole field of knowledge of the student.2. Facilities for special education, which are intended to remedy a specific defect, or to give proficiency in some special field. This may be divided as follows;a. Training for work, intended to fit an employee to adequately perform the task assigned to him, this ranges from brief instruction by a foreman or fellow-worker up to definite training courses in which the employee dose nothing but study for a period of several weeks or months, being paid during this period a wage that may range from a nominal amount up to practically full time salary. The student's educational preparation may already be fairly advanced. Some of the manufacturers of electric machinery maintain, a school similar to that just described for graduates of engineering colleges. In other cases the only pre-requisite may be a common school education, as in the schools for operators, maintained by the telephone companies."

Apr 1, 1920

By H. H. Dewing

The Bureau of Mines constructed a process research unit (PRU) to demonstrate new technology for extracting zinc from sphalerite concentrates. Up to 9 kg/hr of sphalerite (ZnS) concentrate was reacted at ambient pressure in the PRU with 80 pct sulfuric acid at 160° to 180° C to produce zinc sulfate and elemental sulfur. The PRU consisted of a three-stage glass reactor system: a 4-liter premix stage in which feed was slurried with 78 to 82 pct H2S04, a 40-liter stirred reactor, and a ISO-liter settling stage in which high reaction conversions were effected and excess H2S04 for recycle was separated from insoluble ZnS04 and sulfur. Evolution of sulfur-containing gases was minimized by sub-surface addition of acid feed slurry to the stirred reactor and by exclusion of air from the reactor to prevent the oxidation of elemental sulfur. Conversion of zinc to zinc sulfate averaged over 99 pct at the optimum acid concentration of 80 pct. Total sulfur losses (primarily S02) were less than 2 pct of the sulfur in the sphalerite. Elemental sulfur remained in the insoluble portion of the settled reactor product after leaching with simulated spent zinc electrolyte containing sulfuric acid. The sulfur residue contained 75 to 89 pct sulfur. Neutral zinc sulfate, required for zinc electrowinning processes, was separated from the sulfuric acid leach solution by crystallization at -15° C as zinc sulfate heptahydrate (ZnS04?7H20). The crystallization operation simultaneously effected a partial concentration of the recycled electrolyte solution by removing water.

Jan 1, 1982

By Donald E. Ralston

The Huntsville study area in northeastern Alabama consists of Jackson, Limestone, Madison, and Marshall Counties. Major emphasis was placed on the Huntsville urban area in Madison County to analyze the relationship of urban growth and the minerals industry. Huntsville was delineated into its component urban, suburban, and rural parts for 1964, and the primary area of growth was predicted for 1990. Population estimates were made for the four-county area as a unit and Madison County separately, and projected to 1990. Demand estimates for crushed stone and sand and gravel were made for the same area units and projected to 1990. Analysis of quarry sites in the Huntsville area was made for the present and for the future. The mineral operations of the study area are all located in rural areas; in the case of Huntsville, the mineral sites are located in areas defined as "rural" in the component urban-suburban-rural system. The operations outside Madison County can expect to have minor problems with urban encroachment, while those operations in Madison County can expect major problems associated with urban growth and development. Some of the problems associated with limes tone production can be reduced if producers invest in capital equipment that will reduce the nuisances inherent in this activity. Although urban expansion endangers some quarry operations in Huntsville, topographic and political restrictions which prevent urban expansion can effectively shield quarry operations for some time.

Jan 1, 1970

By Scott W. Hazen

This report describes the design, analysis, and results of a special experimental mine-sampling project conducted as part of the Bureau of Mines continuing program on sample-methods research. The experimental project was conducted at the Bureau?s Denver Mining Research Center and at the Climax molybdenum mine within the framework of a cooperative research agreement between the Bureau and Climax Molybdenum Co., Division of American Metals-Climax, Inc. The primary objective of the project was to investigate the interrelation-ship between sample volume, number of samples, the standard deviation of an assay distribution, and the precision required for an estimate of grade of ore, and to develop this interrelationship into a relatively simple method of application for use in mine sampling.

Jan 1, 1962

By Oliver Bowles

This paper is the third of a series of reports on asbestos prepared by the Bureau of Mines. The reports already issued contain general information, including descriptions of deposits throughout the world.3/ The present paper deals chiefly with milling and marketing. Many grades of asbestos are marketed, and an important phase of milling is the grading of fiber; these subjects therefore are related so intimately that contiguity in their treatment is fully justified. Although the Bureau of Mines is interested primarily in the mining and preparation of raw materials, the fabrication of asbestos products has attained such importance in the United States that brief reference to processes of manufacture is included. CLASSIFICATION OF FIBER Canadian asbestos fibers are divided into three main groups - crudes, mill fibers, and shorts. The term "crude" is applied to fiber of spinning grade measuring three eighths inch or longer, that is. hand-cobbed and not passed through a mill. Mill fibers are obtained by crushing and beating the fiber-bearing" rock, until the, asbestos is freed and, then removing the fiber from the rock by screening or air separation. Shorts are the lowest grades of mill products.

Jan 1, 1935

By R. A. Cattell

A technologic group such as the Petroleum and Natural Gas Division of the Bureau f Mines, which conducts research on many of the complicated and frequently interrelated problems f extracting crude oil and natural gas from the ground, transporting them to market or to daces for subsequent treatment, and manufacturing products, should report progress from time to time. Engineers and others who apply the results obtained by this division are closely associated with its personnel, because many of the problems are attached cooperatively with groups in industry. Some of this cooperation is formal, as exemplified by work now in progress under cooperative agreements with the States of Oklahoma, Kansas, and others, but much of it is informal, prompted by the desire to be mutually helpful in the public interest. Furthermore, the published reports of the Bureau on subjects pertaining to petroleum and natural-gas technology come to the direct attention of a relatively large number of persons, whose interest in results and appreciation of the value of this type of work have caused them to be kept currently informed regarding available data.

Jan 1, 1940

By Sarkis G. Ampian

The Bureau of Mines has developed a method for identifying fine particles of beryl in mineral samples by preferentially staining the beryl grains. The sample is first subjected to a heated sodium hydroxide solution to etch the beryl particles, which are subsequently stained an intense blue color in a boiling alkaline solution of quinalizarin. Positive identification of beryl grains permits quantitative analyses by microscopic techniques. INTRODUCTION Beryl, a beryllium aluminum Silicate, is the principal ore mineral of beryllium. The only known commercial concentrations of this mineral are found in pegmatite dikes of granitic composition. Normally beryl is associated with muscovite mica, quartz, and the sodium-and potassium-bearing feldspars (orthoclase, microcline, and albite). Other beryllium-bearing minerals which are found occasionally in minor amounts with beryl are phenacite, a beryllium silicate, and chrysoberyl, a beryllium aluminate.

Jan 1, 1962

By James R. Welty

Heat content values were experimentally determined for yttrium metal between temperatures of 400° and 1,300° K and for iron pentacarbonyl between 301° and 380° K. The drop technique was used; that is, a sample of material sealed in a protective capsule was heated to 3 desired temperature in a furnace and then dropped into an ice calorimeter. A revised technique for determining heat content values from calorimetric data is described. Heat content and corresponding entropy-increment data above a reference temperature of 298.15° K are presented in tabular form. Equations for heat content and heat capacity as functions of temperature were derived for each substance. These equations are [Y (c): HT-H298.15 = 1.2041T 1 3.393 x 10-3T2- 0.4176 x 10' T"1 + 739.9 cal/mole Cp = 1.2041 + 6.786 x 10-3T + 0.4176 x 106-T-2 cal/deg mole Fe (CO) E, (1) : HT - H298.15 = 55.636T - 16,588 cal/mole Cp = 55.636 cal/deg mole]

Jan 1, 1963

By G. H. Keith

Oxygen and nitrogen cause strain aging in electrorefined vanadium, as evidenced by maxima in yield and tensile strengths and by Snoek internal friction peaks. Alloys containing up to 0.22 percent oxygen and 0.11 percent nitrogen were investigated. Tensile strengths of oxygen-and nitrogen-containing alloys were 66,000 and 68,000 psi at 300° to 400° C, compared with 53,000 and 62,000 psi, respectively, at room temperature. Total elongation decreases to about 7 percent at the temperature of maximum strength. At 600° C, strain aging is not evident. Based on interstitial contents calculated from internal friction measurement, the increases in strength caused by nitrogen and oxygen were 440,000 psi per weight-percent nitrogen and 260,000 psi per weight-percent oxygen. Application of the Schoeck and Seeger treatment to the Snoek effect in these systems results in a calculated lattice distortion of 0.24 and 0.15 caused by the presence of an interstitial nitrogen or oxygen atom, respectively. Alloys containing boron or carbon were also investigated. Both elements refine the grain size but have no other effect because of their low solubility in vanadium.

Jan 1, 1969

By Herbert H. Einstein

Instability of rock slopes often occurs in the form of excessive movement of bodies that are bounded by discontinuities. The well known limit equilibrium analysis for wedges and blocks suffer, however, from procedural simplifications and from the basic deficiency of limit eguilibrium analysis--the rigid body assumption. Thus, stability analysis for 2-and 3-plane wedges with a wide range of additional features regarding failure modes and external forces have been developed. The deficiency, due to the rigid body assumption, was corrected by an approach that includes the effects or the in-situ stress field and of the stiffness of discontinuities. The final step in making limit equilibrium approaches more valid was achieved with the method of artificial supports which makes it possible to identify among all possible failure modes the critical one and to determine the corresponding factor of safety. The analytical development includes the creation of appropriate computer codes and routines for programmable pocket calculators.

Jan 1, 1979

By C. Ozgen Karacan, William P. Diamond

In This Chapter [Measuring the gas content of coal Predicting gas emissions based on geologic and coal reservoir property data Determining the gas storage capacity of coalbeds and other gas-bearing strata Methane drainage borehole monitoring to forecast the remaining gas-in-place and the influence on mine emissions Forecasting gas emissions during mining as a function of mining parameters and Gas emission prediction based on numerical simulation] This chapter provides guidelines for determining the gas content of coalbeds, estimating the gas-in-place, and predicting gas flow and emissions before and during coal mining operations. The techniques are discussed briefly in the following sections. However, detailed information on the techniques is provided in the cited references. INTRODUCTION Coalbed methane, if not properly controlled in the underground mine environment, is a safety concern due to the potential risk for an explosion. This is a particular problem during longwall mining, where the high rate and volume of coal extraction can result in the release of large amounts of methane from the mined coalbed and other adjacent gas-bearing strata. The variability and potential hazards of these sometimes unexpectedly high gas flows provide the impetus to develop methods to predict methane emissions into the underground workplace. A forecast of the volume of gas that might be released during coal mining is helpful for designing ventilation systems and for implementing optimum methane drainage strategies to help mitigate expected gas emission problems. A complete assessment of the need for methane drainage prior to mine development generally requires both an empirical and a theoretical approach. If there are active mines in the general area with similar geologic conditions and coal characteristics, a review of gas problems in those mines provides an initial insight into the level of gas emissions to be expected at a new location. In addition, relatively simple methods exist to determine the in situ gas content (volume of gas per unit weight of coal) of the coalbeds in a particular mining area, as well as the gas-in-place (volume of gas in the coalbed(s) within a defined geographic area).

Jan 6, 2006

By B. W. Gandrud, A. C. Richardson

"INTRODUCTION The Bankhead mine of the Cane Creek Coal Mining Co. is in the central part of Walker County, Ala., 4 miles south of Jasper. The Mary Lee bed in this part of the State yields a practically free-burning coal which is marketed as a. steam-raising and domestic fuel. As mined, the coal ordinarily contains ash-forming impurities to an extent that makes it necessary to treat the coal by some washing process before it is marketed. At present the Bank-head coal coarser than 3-1/2 inch is hand-picked and the coal finer than 3-1/2 inch is washed in two single-compartment jigsThis paper contains the result of screen-sizing and float-and-sink tests on a representative sample of the run-of-mine coal and the results of tests made to show the amount of coal liberated from impurities by crushing the coarser sizes. .This report is one of a series on the washability of Alabama coals which is being prepared by the U. S. Bureau of Mines and the University of Alabama, with the cooperation of the coal producers of Alabama.SAMPLING AT THE MINE'The Mary Lee bed at Bankhead consists of two benches separated by a rock parting which varies in thickness from place to place in the mine. The top bench has a very uniform thick-nest; throughout the workings and yields about 65.0 per cent of the output. The bottom bench varies greatly in thickness and in nary places becomes too thin to work at a. profit. The sample for the washability study was taken underground at a place which was typical of the mine as a whole. In taking the sample the working face was squared up and a representative section out from each bench. Care was taken to secure a, quantity of coal from each bench proportional to the quantity contributed to the mine output. The rock parting as gobbed in accordance with the usual mining practice. The total sample taken weighed 3 tons."

May 1, 1933