Search Documents

By R. Barany

In this paper, closed expressions have been obtained for the frequency spectrum of a Born-Karman square lattice in terms of elliptic and hyperelliptic integrals. This work is part of continuing research by the Bureau of Mines with the thermodynamic properties of metals and minerals. Although other workers have obtained various types of approximations for the general case of the frequency spectrum of a square lattice, no one previously has obtained closed analytic expressions for this spectrum. To understand the optical and thermodynamic properties of crystals, several investigators have studied the distribution of frequencies of normal modes of vibration of the crystal lattice. Born and Karman3 laid the foundation for the theory of lattice dynamics and obtained detailed results for the case of a one-dimensional lattice. Blackman4 used numerical techniques to estimate the frequency distribution of a two-dimensional square lattice. Mbntroll5 analytically determined the frequency distribution of a square lattice for a particular value of the force constants. He also studied the more general problem and obtained some analytic approximations, using the method of moments. However, the calculations by this method were so difficult that it was not always practicable to carry them out. Van Hove6 and Montroll7 studied the nature of the singularities in the frequency spectrum of both a two and

Jan 1, 1962

By W. P. Diamond, B. M. Bench, C. M. McCulloch, Maurice Deul

As part of the Bureau of Mines methane control program, the Pittsburgh coalbed was studied in Washington and Green Counties, Pa., and in Marion and Monongalia Counties, W. Va., where this coalbed is now being mined at its greatest depth. The coalbed thickness appeared to be structurally controlled; the bed was generally thinner near the axes of anticlines and thicker near the axes of synclines. The overburden isopach shows a similar relationship. Most of the clay veins in coal occur in the synclinal troughs, generally under sandstone roof. Cleat orientations measured in 18 underground mines showed that face cleats are perpendicular to the axial trends of the folds, and the butt cleats are parallel to the axial trends, indicating structural control of the cleat. Measurement and analysis of surface joint orientations provide a method for predicting the cleat orientations of the coalbed, but linears measured from infrared photographs and photoindex sheets helped only to determine regional trends. The results of these investigations provide a geologic framework for rational planning for underground mine development to use the best available technology to cope with methane emissions, coalbed discontinuities, and related ground support problems.

Jan 1, 1975

By J. W. Eckerd

Metal production rates of 42 to 45 tons per day were obtained with hollow-core anthracite briquets in an experimental blast furnace. Tuyere pressures were about the same for both coke and briquet operations, but from 150 to 175 pounds more of briquets were required per ton of metal than were needed with coke. Furnace operations were comparatively smooth, furnace hanging occurring less often than in previous tests with anthracite briquets. Dust production was substantially higher than with coke, however, and metal quality could not be controlled by corrective burdening and moisture control.

Jan 1, 1968

By Seth C. Schaefer

The Bureau of Mines studied the standard free energies2 of formation of ferrous fluoride (FeF2) and ferric fluoride (FeF3) with high-temperature galvanic cells employing calcium fluoride doped with 1 mole-pet yttrium fluoride as the electrolyte. A free-energy change for the cell reaction Fe (s) + NiF2 (S) = FeF2 (S) + Ni (s) together with the standard free energy of formation of nickel fluoride yields a standard free energy of formation of ferrous fluoride from the elements of ?GF° = -168.74 + 30.63 x 10-3T ± 0.41 kcal/mole (897-1,098 K). (2) Combining the standard free energies of formation of magnesium fluoride, ferric oxide, and magnesium oxide with the free-energy change for the overall cell reaction 3MgO(s) + 2FeF3 (s) = 3MgF2 (S) + Fe2 03 (S) (3) gives a standard free energy of formation of ferric fluoride from the elements as ?Gf° = -281.45 + 90.46 X 10-3T ± 0,67 kcal/mole (880-935 K). (4) Free energies and equilibrium fluorine pressures for the two univariant equilibria of the Fe-F system are tabulated and illustrated.

Jan 1, 1975

By A. L. Engel

The Stayton Mining District in San Benito County, Calif., near Hollister, includes several square miles with many occurrences of antimony ore. The sample submitted for the test described in this paper came from a vein said to have been traced and sampled for 5,000 feet on the surface, 1,500 feet carrying 2-1/2 to 3 percent antimony and the remainder 1/2 to 2 percent. Thirty thousand tons 'With a content of 3 percent antimony are said to be blocked out. A drift of 200 feet on the vein has shown ore containing 4.2 percent antimony. The present sample assayed 3.8 percent. Previous flotation investigation of this are resulted in a recovery of only 71.6 percent in concentrates containing 56.8 percent Sb. It was desired to develop a method of treatment that would give better results. The antimony in the sample occurred as the mineral stibnite, Sb2S3, antimony sulfide.

Jan 1, 1949

By R. V. Ramani, P. M. T. White, D. Sutton

This report was prepared by The Pennsylvania State University under USBM Contract No. G0111808. The contract was initiated under the Coal Mine Health and Safety Program. It was administered under the technical direction of DMSE, with Mr. G. R. Schottler acting as the technical project officer. Mr. J. A. Herickes was the contract administrator for the Bureau of Mines. This report is a summary of the work recently completed as part of this contract during the period June, 1971 to December, 1973. This report was submitted by the authors on March 31, 1974. The project personnel express their thanks to Dr. Jay Politzer, The Pennsylvania State University Computer Center for providing the subroutine POLITZ and function IFIND, to Dr. Ray Masters, Department of Architectural Engineering, for permission for the use of the GRID program and to Dr. Lother Weyher of Bethlehem Steel Corporation for providing coal data.

Jan 1, 1974

By C. E. Brechtel

A testing program was conducted to design a cemented backfill fur hydraulic placement in underhand cut and fill mining of a steeply dipping coal seam. The testing evaluated the use of three different backfill aggregates, locally available at the coal mine, with Portland cement and five different pozzolans, including a Class F fly ash, a Class C fly ash, a cement kiln dust and ground smelter slag. Both viscosity and uniaxial compressive strength of backfill mixtures with different pozzolan and Portland cement contents were used to evaluate their suitability. Based upon the results of preliminary testing, an optimum mixture of alluvial sand with six percent Portland cement and ten percent Class F pozzolan was chosen for further compression testing.

Jan 1, 1985

By M. A. Schellhardt

In recent years development of instruments and equipment for determining subsurface pressures and temperatures in. gas and oil wells has made it feasible to obtain information that eras not available in the past on many gas-production problems. The material presented in this report illustrates particularly the value of subsurface-temperature data in the study of subsurface leakage from gas wells. An abnormal decline in the shut-in pressure of the Lone Star Gasoline Co. A. Jones No. 1 gas well in the southern part of the Buffalo (Tex.) field was observed during an interval when a negligible volume of gas bras being withdrawn from the reservoir. Wellhead-pressure readings indicated that the shut-in pressure of the well declined from 2,295 pounds per square inch gage on February 3, 1937, to 1,445 on February 12, 1935. Tests conducted by engineers of the Lone Star Gas Co. suggested that the subnormal pressure gaged on February 12, 1938, probably was not caused by a head of liquid in the well.

Jan 1, 1940

By P. B. Grote

The report is concerned with the issue of the possible transfer of U.S. and other developed country deep ocean mining (DOM) technologies to developing countries. This subject is one of several major issues in current UN Law of the Seas negotiations. As background to the subject, the report provides a detailed critique of the various terms and conditions pertaining to technology transfer in recent negotiating texts. It also provides a description of the relevant DOM technology, sources of innovation, and methods of proprietary protection. Functional requirements for viable technology transfer are developed and used as a basis for the definition of alternative levels of programs and implementation approaches, including required changes in the negotiating text. The consequences of these technology transfer options on the various parties are investigated.

Jan 1, 1978

By NIOSH Publication

In 2004, a total of 7,074 sand and gravel mining operations reported employment to the Mine Safety and Health Administration (MSHA).

Sep 1, 2007

By H. William Zeller, T. E. Westpha1

The U.S. Bureau of Mimes evaluated the effects of two iron-based fuel additives on diesel particulate matter (DPM) emissions. The 5.6-L, six-cylinder test engine is typical of engines used in underground mines. One additive, ferrous picrate, did not measurably affect exhaust emissions. This report is mainly about a ferrocene-based additive that reduced DPM between 4 and 45 pct, depending on engine operating conditions. The report concludes that the DPM reductions were caused by the catalytic oxidation properties of a ferric oxide coating that developed inside the engine's combustion chamber. The ferric oxide coating also decreased gas-phase hydrocarbons and O, but it increased CO, and NO,. The increase in NO,, of about 12 pct, is considered the only adverse effect of the ferrocene-based fuel additive. The results suggest that the effectiveness of ferrocene was partially offset by increased sulfates because of the high-sulfur fuel used. Recommendations for continuing fuel additive research are presented.

Jan 1, 1992

In 2004, a total of 4,401 stone mining operations reported employment to the Mine Safety and Health Administration (MSHA). Stone mines comprised 30.4% of all mining operations.

Sep 1, 2007

By J. Gautam, T. Ong, W. E. Wallace, M. Keane, S. Xing, J. Harrison

"INTRODUCTIONOrganics extractable from respirable diesel exhaust soot particles by organic solvents have been known for some time to be direct acting frameshift mutagens in the Ames Salmonella typhimurium histidine reversion assay (Huisingh, et al). Upon deposition in a pulmonary alveolus or respiratory bronchiole, respirable diesel soot particles will contact first the hypophase which is coated by and laden with surfactants. To model interactions of soot and pulmonary surfactant, we dispersed soots in vitro in the primary phospholipid pulmonary surfactant dipalmitoyl glycerophosphorylcholine (lecithin) (DPL) in physiological saline. We have shown that diesel soots dispersed in lecithin surfactant can express mutagenic activity, in the Ames assay system using S. typhimurium TA98, comparable to that expressed by equal amounts of soot extracted by dichloromethane/ dimethylsulfoxide (DCM/DMSO)(Wallace, et al, 1987). Here we report additional data on the same system using additional exhaust soots and also using two other phospholipids, dipalmitoyl glycerophosphoryl ethanolamine (DPPE), and dipalmitoyl phosphatidic acid (DPPA), with different ionic character hydrophilic moieties. A preliminary study of the surfactant dispersed soot in an eucaryotic cell test system also is reported.MATERIALS AND METHODSSoots D4 and D6 were collected at two different times as scrapings from the exhaust pipe of a diesel tractor-trailer immediately after the engine was stopped. Surfactant dispersions were made by ultrasonic probe sonicating 25 mg of commercially obtained DPL, DPPE, or DPPA into 1O ml of O.85% physiological sterile saline (PSS) for 10 min at 40 watts power. For surfactant dispersions, 2.5 mg soot was mixed into 2.5 ml of the appropriate phospholipid dispersion. Mixtures were sonicated by 40 watts sonicator probe for one min, then incubated in the sonicator water bath for 30 min at room temperature; the mixture was then incubated for one hour at 37C while being rotated continuously. Dilution series were made with saline. For solvent extraction, 2.5 mg soot was mixed into 2.5 ml of DCM and incubated in a sonicator water bath for 30 min at room temperature. The sample was then mixed with 2.7 ml DMSO, placed in a dry bath at 45C, and the DCM evaporated under a stream of nitrogen gas until 2.5 ml of liquid remained. Ames salmonella/microsome assay utilizing TA98 for frameshift mutation was used for mutagenicity testing, with and without S9 activation, as described by Ames et al (1975). Unfiltered sample extractions or dispersions were preincubated with tester cells for 90 min at 37C : 0.1 ml of sample was mixed with 0.5 ml of PSS, or of S9 mixture, and 0.1 ml of an overnight TA98 culture incubated samples were then added to 2 ml of top agar supplemented with biotin and a trace amount of histidine, and overlayed onto Vogel-Bonner minimal media plates. After 48 hours incubation at 37C, revertant colonies were counted. Solvent controls were DMSO, DPL, DPPE, DPPA, and saline. Positive controls were trinitrofluorenone (1 ug/plate), for samples not treated with S9, and 2-aminoanthracene for S9 treated samples (2.5 ug/plate). All samples were assayed in duplicate. Sister chromatid exchange (SCE) assay was performed, following Lett, et al (1981), using V79 cells, of Chinese hamster pulmonary fibroblast origin. Stock diesel sample suspensions were made as 10 mg soot/ml DPL suspension, or 20 mg soot/ml in DMSO. Aliquots of these soot preparations were added to 15 ml of culture medium per sample flask to result in concentrations of 25, 50, and 75 ug soot/ml medium. After 12 hours incubation, 200 ul of 25 uM 5-bromodeoxyuridine (BrdU) was added to each flask. After another 35 hours incubation, 200 ul of 10 ug/ml colcemid were added; and the cells were harvested three hours later. Cells were swollen by hypotonic saline, and fixed twice with methanol/acetic acid, and burst on microscope slides. Cells on the slide were stained with Hoechst 33258, exp"

Jan 1, 1990

By M. L. Bowser

Pulse-forming circuitry is described for use in explosives research that requires precise synchronization and control of events in order to investigate detonation parameters. Included are pulse generators for oscilloscope sweep control, counterchronograph actuators, and a raster-type oscillographic method for the determination of velocities of detonation that are applicable to studies on solid, liquid, and gaseous detonations. INTRODUCTION Prom time to time, requests have been received for information on electronic circuitry used in explosives work at the Explosives Research Laboratory, Bruceton, Pa. The methods used are not entirely original;4 5 6 however, modifications of earlier techniques and some novel design aspects have resulted in time-tested methods that warrant a more detailed description.

Jan 1, 1962

By Benjamin Petkof

Production quarry blasts in three rock types were photographed with a high-speed camera. Analysis of the films showed that step increases sometimes occur in the horizontal velocity of the broken rock. These step velocity increases were observed only in the first foot or so of rock movement. This observation indicates that the gaseous products of the explosion do additional work on the rock after it is crushed and cracked by the initial compressive-stress pulse and the reflected tensile-stress pulse. The observed initial fly-rock velocity is compared with the calculated fly-rock velocity for reflection spalling. A mechanism possibly causing the velocity increases is discussed. INTRODUCTION When a small concentrated charge of explosive is detonated at the bottom of a drill hole near a free surface, two modes of rock failure have been observed; both are associated with the stress pulse generated in the rock by the detonating explosive. The first mode of failure is the crushing and radial tensile cracking associated with the initial passage of the compressive-stress pulse as it propagates outward from the explosion. This type of rock failure is usually confined to the immediate vicinity of the charge hole. The second mode of failure is the tangential and radial tensile cracking associated with the tensile-stress pulse that is reflected from the free surface. This mode of failure is commonly called scabbing or spalling and has been shown to be a primary cause of rock failure in crater formation at one free surface. (3).4

Jan 1, 1961

By H. O. McDonald

Solutions containing Cr6+ and sulfuric acid are used in a number of surface-finishing operations. Substantial quantities of chromium and copper are lost and pollution problems are created when the spent solutions are discarded. To minimize the undesirable environmental effects while improving secondary resource recovery technology, the Bureau of Mines is conducting research to detoxify and recover metals from these solutions. Spent etchants are treated to remove copper and reduce Cr6+ to Cr 3+ in an electrolytic cell. The anodes and cathodes are granulated coke. The spent solution is continuously pumped through the electrodes. Hexavalent chromium is reduced to trivalent chromium, and copper is recovered at the cathode. Reoxidation of Cr3+ at the anode was not observed. The removal and recovery of copper reduction of Cr6+ lessen chemical demand and increase efficiency in waste in treatment operations associated with the use of these solutions.

Jan 1, 1980

By William H. Schiffbauer, Timothy Lutz, Michael R. Yenchek

The National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Research Laboratory (PRL) participated in an experiment to facilitate the remote control of dozers used on coal stockpiles. The experiment consisted of supplementing the normal sensory cues an operator requires to manipulate the dozer from a remote location. NIOSH provided and tested a vision systems intended to give the operator the ability to operate the dozer safely and efficiently from a remote position. This paper highlights the genesis of the experiment, identifies the contributions of Consol Energy and Caterpillar, and details the NIOSH efforts and successful test results. Keywords-remote-control; vision system; stockpiles; safety

By H. W. Davis, W. W. Adams, O. E. Kiessling

"Current economic problems frequently have focused attention upon the lack of adequate quantitative information indicating the relationship between human effort and output in various branches of the mineral industry. With the exception of complete records covering coal mining, only scattered information on the units of human energy required to produce a unit of raw material is available for most of the important industrial minerals. Fortunately a virtually complete statistical record is available covering this phase of the iron-ore mining industry.For many years iron-ore mining companies, whose interest in safety work is well-known, have reported annual data on employment to be used in the compilation of accident statistics. These data on hours of labor and other detailed employment information have been correlated with the statistics on production also reported annually by producers. The outstanding trends shown by this composite record for the 10-year period 1923-32 are included in the following discussion, supplemented by a summary table that presents the principal statistical background of the study. 5The substantial reduction in the number of men needed to produce the annual iron-ore requirements of the United States, as shown strikingly in the graphs, illustrates that in iron-ore production improvements in technology have been consistently winning a battle over the difficulties of nature. In 1923, for example, 41,294 men working 107,551,244 hours were required to produce 69,351,442 gross tons of merchantable ore, equivalent to an average output of 0.645 ton per man-hour. In 1929, however, only 30,763 men working 77,111,686 hours 'zero required to produce 73,027,720 tons of merchantable ore, equivalent to an average output of 0.947 ton per man-hour. Thus, from 1923 to 1929 the average number of men working decreased 25.5 percent and the total man-hours worked 28.3 percent, while the average output per man-hour increased 46.8 percent and total merchantable ore production 5.3 percent."

Feb 1, 1935

By Mark Sanders

This report describes an experiment which was conducted to compare the relative bumping hazard of a low and high profile hard hat (helmet) in a low seam mining environment. The study was specifically designed to assess the effect of lowering the helmet profile on frequency of head impacts in an underground low seam coal mine simulator. This involved subjects performing four common low coal mining tasks wearing the low and high profile helmets in the low seam simulator (36" and 48? heights). The results of the study indicated that a low profile helmet could reduce bumping frequency in underground low coal approximately 25%, and as much as 80% on selected tasks. It was beyond the scope of the study to measure the impact force, thus it was not possible to estimate the effect of the low profile helmet on severity of impacts underground. The research team recommended that a more extensive investigation be made of head injuries experienced in low seam mining (both underground and surface) with the objective being to assess the impact of a low profile helmet on total head accident exposure.

Jan 1, 1980

By R. L. Marek

The number of persons fatally injured in the California petroleum industry in 1931 was 30, a decrease of 20 fatalities or 40 per cent from the number killed in 1930. As a result of the decrease in the number of fatalities for 1931, the fatality curve of tie California petroleum industry reached its lowest point in nine years. Although reductions in personnel--which permitted the retention of a select and experienced class of workmen, decreased active field-development work, and curtailed production--undoubtedly have had a marked effect on reducing the number of fatalities in 1931, the decrease also has resulted from continued accident-prevention efforts. Statistics show that a direct relationship exists between development activity and the number of men accidentally killed in the drilling and producing division of the California petroleum industry. For example, when the average number of drilling wells in 1930 was 29 per cent less than in 1929, the number of men accidentally killed at drilling wells dropped 48 per cent; and when the average number of drilling wells in 1931 decreased 52 per cent from 1930, the number of fatalities at drilling wells decreased 58 per cent. The relationship between field-development work and fatality frequency is significant because each year at least 50 per cent of all the fatalities in the California petroleum industry occur in the drilling and producing division. This relationship should serve to guide the accident-prevention efforts of the industry, especially in the drilling and producing division, toward checking an increase in fatal accidents when development activity again takes an upward trend.

Jan 1, 1932