Search Documents

By John Nagy

This circular has been prepared for the guidance of safety engineers, shot firers, and coal-mine inspectors concerning multiple blasting with short-delay (millisecond-delay) detonators. These special precautions are suggested in addition to those normally followed in blasting, as outlined in the Federal Mine Safety Codes 5 6/ and in Miners' Circular 58.7/ INTRODUCTION The use of short-delay blasting has been proposed for promoting safety and increasing the rate of production in coal mining. Ideally, short-delay blasting, as compared with equivalent single-shot blasting, reduces exposure of the shot firer to dust, fumes, and weakened roof; as compared with equivalent simultaneous blasting, it reduces roof disturbance.

Jan 1, 1959

By Jeanne A. Smith, Suzanne D. Smith

Annoyance, fatigue, and musculoskeletal pain have been reported during prolonged exposures to propulsion-generated vibration in military propeller aircraft1. The objective of this study was to determine the vibration mitigation properties of selected seat cushions and the effects of occupant seating posture during exposure to higher frequency multi-axis vibration associated with military propeller aircraft. Methods A Navy E-2C Hawkeye crew seat was mounted onto the Six Degree-of-Freedom Motion Simulator (SIXMODE). Six seat pan cushion configurations were tested during exposure to an E-2C vibration signal collected in the field1. Seat pan cushions 1 – 5 were used with the original E-2C seat back cushion. Cushion configuration 6 included seat pan cushion 5 with a prototype seat back cushion. Triaxial accelerometer pads were mounted onto the seat pan and seat back cushions to measure the vibration entering the human. Data were collected for seven subjects seated upright with their backs in contact with the seat (back-on) and not in contact with the seat (back-off). Spectral analysis techniques were used to analyze data at the two dominant frequencies associated with the propulsion system (propeller rotation frequency (PRF) ~18.5 Hz, and blade passage frequency (BPF) ~73.5 Hz). Overall accelerations were also calculated between 1 and 80 Hz. Vibration Total Values (VTVs) were calculated using the weighted seat pan and seat back (back-on only) accelerations and compared to the comfort reactions given in ISO 2631-1: 19972. Results In general, the highest accelerations observed at the seat pan occurred in the fore-and-aft (X) direction at both the PRF and the BPF for all cushions and both postures. The most pronounced effect was at the BPF in the X direction, where all configurations showed significantly lower seat pan accelerations than configuration 1 (original E-2C cushion) with the back-on posture. Configuration 5 was the exception with the back-off posture (Fig. 1A, Repeated Measures ANOVA, P<0.05). The most pronounced effect of posture occurred at the PRF in the X direction, where all cushion configurations showed significantly lower seat pan accelerations with the back-off posture (Fig. 1B). All configurations except configuration 2 showed similar VTVs as compared to Configuration 1 (Fig. 2, P<0.05). Configuration 2 tended to show the lowest weighted acceleration levels. The overall VTVs (back-on only, Fig. 2B) showed significantly higher accelerations as compared to both the back-on and back-off seat pan point VTVs (Figs. 2A &

Jan 6, 2006

By Terry R. Neumann

A mineral survey of the 23,760-acre Abert Rim Wilderness Study Area (OR-1-101) was conducted by the U.S. Bureau of Mines in 1986 at the request of the Bureau of land Management in order to evaluate its identified mineral resources. The study area is located in south-central Oregon, 26 mi north-northeast of Lakeview, OR. Federal and Lake County mining records indicate no mining claims, geothermal leases, or oil and gas leases within the study area as of January 1, 1987. No economic concentrations of minerals were found in the study area. The Wilderness Study Area is dominated by Abert Rim, a north-trending Basin and Range fault scarp that parallels the study area&apos;s western boundary. Exposed on the scarp is an approximately 2,000-ft-thick volcanic sequence consisting of Oligocene-Miocene basalts, tuffs, and tuffaceous sedimentary rocks.

Jan 1, 1987

By Roger E. Burleigh

In June, 1989, the U.S. Bureau of Mines, undertook a 9-day evaluation of the tin resource potential of the Sleitat Mountain tin deposit. Significant tin-tungsten mineralization is associated with quartz-topaz-white mica-tourmaline greisen alteration of a multi-unit, 57 Ma, peraluminous, granite stock which intrudes Cretaceous Kuskokwim Group flysch deposits. The granite comprises marginal biotite-, intermediate biotite-muscovite-, and central zinnwaldite-granite units, interpreted as a zoned alteration system. Major vein mineralization is confined to two east-west-trending zones of steeply oriented tabular lenses of greisen interleaved with mildly altered granite. Cassiterite is the dominant ore mineral while arsenopyrite, loellingite, wolframite, pyrite, sphalerite, chalcopyrite, and bismuth-oxides are present in minor to trace amounts. The north and south greisen zones are estimated to contain an inferred resource of 128 to 212 million lbs Sn in 28.6 million st of mineralized rock. An 1,800-lb representative bulk sample contained 0.37% Sn, 0.04% W and 17 ppm Ag and is considered an average grade estimate for the deposit. Drill testing by Cominco Alaska Exploration indicates that substantial widths of high-grade tin mineralization are included within the lower grade disseminated mineralization. Depth of deposit erosion is substantial and there exists a high probability for placer tin deposits.

Jan 1, 1991

By Wallace W. Roepke

The Bureau of Mines has a well-established health and safety research effort directed to fundamental studies of the mine cutting system. This report describes the ignition danger of using cutting bits with flat wear area on still-intact carbide inserts.

Jan 1, 1983

By F. M. Goodwin, John Campbell, G. W. Jones

"INTRODUCTION In previous reports 5 results were given of a manhole investigation carried out over a period from June 1929 to July 193C in cooperation with the Edison Electric Illuminating Co. of Boston. Mass., and during 1931 in cooperation with the Edison Electric Illuminating Co. of Boston and the Boston Consolidated Gas Co., to determine the general hazards of combustible gases and vapors in manholes and other underground openings owned by the Edison Electric Illuminating Co. and to develop methods of eliminating these hazards. These investigations have demonstrated that the detection, control, and elimination of combustible hazards in manholes can best be obtained by a close cooperation of the interested parties through a systematic and continuous inspection of manholes, under proper supervision.The investigation carried out during 1932 has been along lines similar to those conducted during 1929, 1930, and 1931 test crew consisting of two men, one an employee of the Consolidated Gas Co. and the other an employee of the Edison Electric Illuminating Co., was continuously employed during the year in the testing of gases in manholes served by the Edison system. The test crew was under the direct supervision of John Campbell, superintendent of the special service department of the Edison Electric Illuminating Co., and F. M. Goodwin, vice president of the Consolidated Gas Co.As in the previous investigations, all tests were numbered. The test-data sheets, on which the information regarding the tests was recorded, were prepared in triplicate, ono copy going to the Edison Co., one to the gas company, and the third to the Bureau of Mines at Pittsburgh, Pa. These test-data sheets were then filed (1) according to the town, (2) the street location, and (3) the manhole number; in this way a complete record of each manhole tested was immediately available. A typical test-data sheet was given in the 1931 report. These data sheets were found to entirely satisfactory and no changes were made during the 1932 investigation. The procedure of sampling manhole atmospheres, shipment of the samples to Pittsburgh, and method of analysis has been the same as that described in the 1931 report and need not be repeated here. Likewise, there has been no change in the method of calculation of explosibility of the samples analyzed or the use of charcoal filter tests given in appendix A."

Jun 1, 1933

By Stephen C. Tadolini

The anchorage capacity of four types of bolting systems was investigated in two mines with thick coal roofs. In conjunction with the in-mine tests, a simple axisymmetric finite element computer program was developed. Both the field and computer results indicated that thick coal roofs can be effectively supported entirely by the coal member.

Jan 1, 1986

By W. P. Diamond, A. C. Smith, J. A. Organiscak, T. P. Mucho

The U.S. Bureau of Mines conducted a worldwide literature review of bleederless ventilation practices to evaluate their use as a spontaneous combustion control measure in U.S. coal mines. Factors that must be taken into account in the design and use of these systems include seal construction, the use of ventilation control devices, the use of methane-drainage systems in gassy mines, and the ground control plan. Monitoring for the detection of spontaneous combustion and the control of methane when methane-drainage techniques are employed is critical to the successful use of a bleederless ventilation system. This report describes the types of ventilation systems used throughout the world and the spontaneous combustion risks associated with these systems. Methane-drainage systems used in conjunction with bleederless ventilation systems are discussed. Ground control considerations such as pillar design, entry stability, and seal usage are reviewed. Monitoring systems for spontaneous combustion detection, methane-drainage control, and behind seals are examined. Finally, methods for evaluating the spontaneous combustion hazard of a mining operation to determine when the use of a bleederless ventilation system is warranted are reviewed.

Jan 1, 1994

By Sidney Katell

This Bureau of Mines study estimates typical capital investments, operating costs, and selling prices for two bituminous coal strip mines in the Eastern and Interior provinces and a subbituminous coal operation in the Northern Great Plains province. The annual productions were based on tonnage required to fuel a 250-MM-scfd, high-Btu gas plant. The annual tonnage for the Eastern province mine is 4.8 million tons; for the Interior province mine, 6.72 mi 11 ion tons; and for the Northern Great Plains province mine, 9.2 million tons. It is assumed that the mines have a 20-year life. Wages and union welfare payments are considered as of May 12, 1974, under the terms of the Bituminous Wage Agreement of 1971, and costs for material and equipment are based on 1973 and early 1974 indexes . Initial capital investment varies: $45,358,600 for the 4.8-million- ton-per-year (MM tpy) mine in the Eastern province, $54,603,000 for the 6.72 MM tpy mine in the Interior province, and $29,871,000 for the 9.2 MM tpy mine in the Northern Great Plains province. Total capital invest-ments for the Eastern province mine, the Interior province mine, and the Northern Great Plains province mine are $61,070,000, $76,753,000, and $56,286,000, respectively. Corresponding selling prices for the coal, per ton, are $4.79, $4.23, and $2.66, assuming a 12-percent discounted cash flow rate of return after Federal income taxes. These studies are considered typical for the areas involved. Costs will vary depending on specific locations in these areas.

Jan 1, 1974

The U.S. Bureau of Mines evaluated water-jet-assisted longwall shearers in full-scale laboratory tests and underground. Both test programs showed that use of high-pressure water did little to reduce the shearer motor energy required to maintain a given cutting rate. However, three other major benefits were achieved with the use of water-jet-assisted cutting. At a pressure of 1,800 psi, respirable dust levels were reduced about 80 pct compared with the dust levels of the conventional water spray system operating at 340 psi. Operating at higher pressures required for water-jet assist also resulted in an increase in the average size of coal cut, which translates into a decrease in product fines. Finally, although no controlled measurements of bit wear as a function of water pressure were made, mine personnel reported that the shearer bits lasted longer when water-jet-assisted cutting was used.

Jan 1, 1989

By Anthony Iannacchione, Christopher Mark

Residents of Maxwell Hill, a suburb of Beckley, West Virginia, reported from January until March of 1988 a series of earth tremors. The tremors rattled dishes, and the noises associated with tremors were sometimes loud enough to wake people at night. These events were puzzling because Beckley is in an area of low seismic activity. Maxwell Hill is located above abandoned coal mines, though no direct subsidence damage to surface structures has been documented. A research program was initiated to determine whether subsurface ground movements associated with the abandoned mines could be responsible for the seismic activity experienced at the surface. A hypothesis is proposed which states that seismic disturbances can be caused by abandoned mine failure when two conditions are met. First, some instability must exist at the mine level. The most likely cause of instability is the failure of pillars of coal that were left for support at the time of mining. Second, subsurface movements can result in significant seismic activity only when the rock above the mine contains at least one very strong and brittle layer that is prone to fail violently through rupture or fault slip movement. Analysis of the data indicates that both hypothesized conditions for mine-related seismicity appear to have been satisfied in the case of Maxwell Hill. It has therefore been concluded that the earth tremors experienced by Maxwell Hill residents probably are related to the abandoned mines. Analysis of the potential magnitude of these events indicates that they are unlikely to cause significant surface danlage. The probability that future events will disturb the residence of Maxwell Hill should be quite low based on the identified mechanism.

By Lucia Kuizon

The Miranda Pine Roadless Area Review and Evaluation (RARE II) study area (No. 5114) comprises 12,600 acres (5,100 ha) in Los Padres National Forest in Santa Barbara County, California, about 15 mi (24 km) east of Santa Maria (fig. 1). Mineral investigations are made by personnel from the U.S. Bureau of Mines on National Forest lands identified as Further Planning Areas in the RARE II program. The Bureau of Mines reviewed literature, mining claim records, and production files; examined the study area; and sampled mineral properties where appropriate.

Jan 1, 1983

By Lung Cheng

The Bureau of Mines has installed passive water explosion barriers in two operating mines to determine their usefulness in U.S. coal mines. The primary objective of this field trial was to determine the effect of the explosion barriers on mining operations. Data were also obtained on the ability of the barriers to withstand the mine environment and on the effect of the barriers on belt operation, ventilation, worker travel, and rock dusting. Fifty barriers were installed at three separate beltway locations, and periodic inspections were made. A year after installation, no defects of the barriers or support hardware were detected, nor was any complaint as to the presence of the barriers made by the mine personnel. To date, 2-1/2 years after installation, the barriers have had no detrimental ef-fect on rock dusting, belt operation, or ventilation. Costs of material, fabrication, and installation are reported herein.

Jan 1, 1984

By VAN. H. MANNING

During the nine years that have elapsed since the Bureau of Mines was established in 1910, the work of the bureau has included many investigations that have proved of high value to the Nation. Eleven mining experiment stations established by act of Congress have greatly increased the bureau's usefulness; being situated in the mining fields, these stations are closely in touch with industrial needs, and the results of their research and educational work are more directly available to those engaged in the mining, metallurgical, and mineral industries. In the United States mining is second in importance to agriculture only. The Federal Government annually appropriates large sums in the interest of agriculture, whereas the appropriations for mining are relatively small. But the nation-wide popularity of Government assistance to agriculture should not overshadow the need of Federal assistance to the mineral industry. With scientific management farms can be made to produce indefinitely without any depletion of the potential resources of the soil, but the mineral wealth of a country is a fixed quantity, and every year's production brings nearer its ulti- mate exhaustion. As the deposits of the richer or more readily available ores, espe- cially those in the West, have been depleted, development of methods for mining and treating the leaner or more inaccessible ores has lagged, so that meeting the increasing demands for certain metals is becoming more and more difficult. In some branches of mining the small inde- pendent operator is greatly handicapped. He has to rely on custom mills and smelters for the profit or loss of his product, and because of relatively inefficient methods of milling or smelting he may receive no return for much of the ore he mines. Even though the small operator thinks he knows of improved methods of obtaining the metals from the ores, he can not afford to install the necessary machinery or to carry on experiments that may or may not prove successful. In view of the increasing need of metals and the impossibility of renewing the ore supplies, efforts should be directed toward developing the most economical and efficient methods in mining and metal- lurgy. The great mining companies carry on independent research work, some of them on a large scale; but as such work is usually undertaken for gainful purposes, these companies do not feel under any obligation to give the results of their investigations to the world. Clearly the solution of the difficulty is to place in the mining districts trained mining and metallurgical engineers who will investigate and solve the problems for the benefit of the whole industry. It is with this purpose in view that experiment stations of the Bureau of Mines have been established to investigate economy, efficiency, and safety in mining, and to make public the results of the investigations. The Federal Government can be of most help in developing the mineral resources of the country when its forces are brought in direct contact with these resources. Mining is as old as civilization, but only within a generation has this country busied itself with any other problem of mining than the amount of mineral products that could be put upon the market. Little concern was felt if much of the metal in an ore was wasted, if the miner lived in unsanitary surround- ings and died of preventable disease, or if accidents occurred fre- quently and from causes that could easily be controlled. Now we realize that the waste of any resource is inexcusable. The mineral wealth of the country can be mined but once. The task before the Nation is to recover as much metal as possible from the ore in the ground, and to do this in the most economical way without waste of human life. This task is of such magnitude as to warrant aid from the Government through experiment stations. In its efforts to make the work of these stations of most benefit to the mineral industry the Bureau of Mines seeks the cooperation of State authorities, of mine operators, of miners' organizations, and of every person interested. These experiment stations also serve an educational purpose. Gen- erally speaking, mining is not a preferred occupation. The miner should have reason to take greater interest in his work; he should feel that the experiments the Government is making affect him vitally by enabling him to increase his production and by making his work safer. The mine operator should realize that the Government stands ready to aid him, and he should know that he can bring his own problems to a Government organization that is trained and equipped to solve them. The surest method of accomplishing these results is to carry the work of the Bureau of Mines into the mining regions through the establishment of experiment stations easily accessible both to the mine operator and to the miner. Many miners in this country do not read English, but they can understand motion pictures of mining methods; they can learn how lives can be saved in case of accident; and they can appreciate the larger results gained by modern methods and equipment. In every

Jan 1, 1919

By Russell J. Miller

A high-pressure intensifier system was designed, constructed and field tested as part of a program to determining the feasibility of applying high-pressure water jets on conventional mechanical rock excavation equipment to increase advance rates. Also developed were a high-volume swivel, capable of transferring the high-pressure water to a rotating cutterhead and manifold system for locating and protecting the jets on the cutterhead. Field tests were conducted in a granite quarry near Skykomish, WA, approximately 90 miles east of Seattle. The concept of improving excavation rates by using water jets to assist mechanical cutting was proven to be successful, with an average increase in excavation mete of 50 to 60%. For some tests, the excavation rate was more than doubled. Machine torque requirements were reduced approximately 25% when the water jets were used. It was suggested this was due to reduced cutterhead friction in the presence of the water jets. A comprehensive economic analysis was undertaken as part of a concurrent study to determine the degree of cost benefits attainable from increased advance rates. Very significant savings were seen to be possible. It was concluded that the basic concept of combining a water jet capability with a mechanical excavating machine is definitely possible.

Jan 1, 1976

By D. Harrington

An explosive may be defined as a substance (usually a mixture) that has the property of yielding, readily to combustion or oxidation upon application of flame or shock, the combustion or oxidation process being rapid and accompanied by formation of such relatively large quantities of gases that much violence and pressure are produced; these, in turn, react against their surroundings and cause what is termed an explosion. By their very nature their action is destructive and disruptive of adjunct materials; hence, all explosives axe potentially hazardous and every type of explosive, irrespective of its relative safety, should be handled, .stored, and used with utmost care at all times and under all conditions. It should always be remembered that any explosive can be rude safe only in certain of its features and under certain conditions and circumstance. If these facts (and they certainly are facts) are always kept in mind, most of the modern types of explosives can be utilized advantageously in our industrial life and with a considerable degree of safety. That commercial explosives can be handled. safely is borne out in part by the fact that in the past 15 years at least 3,000,000,000 pounds of the commercial explosive dynamite have been transported by railroads in the United State, without injury to any person, insofar as available records indicate.

Jan 1, 1939

By R. H. Bedford

"The El Dorado copper mine is situated in the foothill copper-zinc belt of California, which traverses the western slope of the Sierra Nevada with unusual persistence from Butte County to Kern County, a distance of more than 300 miles. Although this area contains such important past producers as the Penn mine, Union, and others, a great part of the current production has been derived from smaller properties, which depend largely on premium metal prices for economical operation. The El Dorado mine is in the latter group, which constitutes an important source of metal in a national emergency.Exploration by the Bureau of Mines by means of eight diamond-drill holes Indicated narrow, intermittent lenses of copper ore along structures boo feet in length. The copper occurs in massive sulfides composed of chalcopyrite, pyrite, pyrrhotite, and minor quantities of bernite. The sulfides have evidently replaced tuffs, which are interbedded with the Mariposa slates and shales.H. A. Weiler and Hal T. Hall, owners of the El Dorado copper property, requested an examination by the Bureau during the latter part of 1914. In December of that year an engineer of the Bureau of Mines visited the mine and recommended the project work undertaken. The purpose was to aid the owners in bringing the property into production of copper and zinc, which at that time was critically essential to the war industries.Complete factual data obtained by the exploration are embodied in this report.In its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G, Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director.Acknowledgment is made to A. O. Johnson, chief, Reno Division, Mining Branch, and Lowell B. Moon, chief, Mining Branch, for their aid and direction."

Jun 1, 1946

By S. R. Zimmerley

As a result of the drilling program of the :Mining Division, Bureau of Mines, large amounts of manganese ores have been blocked out in the Drum Mountain District of Utah. The ores, as mined, would not be acceptable for the production of ferromanganese, and this investigation was made to determine their amenability to concentration by ore-dressing methods and the amount of

Jan 1, 1942

By Louis Schaffer

The purposes of the research were to assess the applicability of new accident investigation methods to mining accidents, and to adapt those found to be applicable in the development of a new methodology for use in mining. The development included field testing, evaluation and modification of the new methodology. The report is in two volumes. Volume one discusses the background research, the design of a methodology for field evaluation, preliminary field tests in Utah mines, and work done to prepare for a formal, complete evaluation by federal government mine safety officials. This, volume 2, discusses the field evaluation done by the contractor and cooperating mines after the program was re-directed by the Bureau of Mines. It relates to research done during a period of approximately eighteen months, ending in April, 1983.

Jan 1, 1986

By John C. Cook

A 1-year program of exploratory research, to determine the feasibility of radar exploration in advance of coal mining, has been completed. Advance detection of obstructions including faults, clay veins, abandoned wells, and pyritic concretions would improve the safety and efficiency of mining. Initial calculations based on laboratory tests of the RF electrical properties of bituminous coals indicated feasibility; radar waves at frequencies below 100 MHz should be detectable through tens to hundreds of meters of coal and be well-reflected by clay, pyrite and metal obstructions. Using a proprietary, experimental, VHF short-pulse "mining radar" system, two cycles of field testing and equipment improvement were completed. Measurements were made in three bituminous coal mines, a quarry, and a salt mine. Comparisons were made with ground-penetrating radar equipment developed by others for salt dome exploration and for military tunnel detection. The proprietary mining radar equipment and techniques used were found to be the most effective known for coal exploration, but further improvements are needed; one major problem in all systems is interfering clutter signals arising in the equipment and from mine room reverberations through leakage coupling of the antennas to the air. Nevertheless, several practical goals have been achieved: excellent radar reflections were received and identified through up to 30 feet of coal; reflections from a wet, abandoned drill hole were identified by their polarization property and detected at distances up to 272 feet, and mine-wall reflections were detected at distances up to 735 feet (both through salt); propagation through and reflections from large vertical clay veins in coal were demonstrated; experimental results agree reasonably well with theory. The results and experience gained during the project affirm the feasibility of the method. They also provide a firm basis for the development of a practical radar technology for exploration in advance of mining. No Subject Inventions, as defined in the contract, were made in the course of this work.

Jan 1, 1971