Search Documents

By K. Hanna

This U.S. Bureau of Mines report describes a rock mechanics instrumentation program conducted in a shallow underground coal mine in central Illinois. This research program was designed to provide a basic understanding of the structural behavior of entry intersections. A wide variety of instruments and measurement techniques including hydraulic borehole pressure cells, multiple-point borehole extensometers, roof bolt compression pads, and overcoring were employed to monitor roof stresses, pillar loading, strata movement, floor heave, and bolt loading before, during, and after intersection development. A summary of intersection design theories, failure modes, and support techniques is included and instrumentation installation procedures and analysis methods are presented. The study identified two critical parameters that affect intersection stability: in situ horizontal stresses and geological discontinuities. Important design parameters for improving intersection stability are roof span and intersection geometry.

Jan 1, 1991

By Henry C. Meeves

The Bureau of Mines, between 1956 and 1963, examined 18 major pegmatite districts in Arizona, Colorado, New Mexico, South Dakota, Utah, and Wyoming to evaluate their content of beryllium, a material in short domestic supply that has become increasingly important to modern industry. This examination report includes the salient statistics on the production of pegmatite minerals other than quartz and feldspar; and brief descriptions of 170 specific pegmatite deposits.

Jan 1, 1966

By Donald R. Johnson

Apparatus developed by the Bureau of Mines for thermal analysis of oil shale was used to determine the thermal properties of shortite. Dissociation of shortite near 470° C occurs as an endothermic reaction that could consume significant quantities of heat in the oil-shale retorting process that produces shale oil. The shortite dissociation products undergo other thermal reactions that would not affect the retorting process. These reactions include crystal inversions near 365° C and 425° C and melting and decomposition endotherms above 500° C. Two separate reaction route for fusion and decomposition of the shortite decomposition products are dictated by the presence or absence of CO2 around the sample.

Jan 1, 1974

By Henry C. Meeves

The Bureau of Mines, between 1956 and 1963, examined 18 major pegmatite districts in Arizona, Colorado, New Mexico, South Dakota, Utah, and Wyoming to evaluate their content of beryllium, a material in short domestic supply that has become increasingly important to modern industry. This examination report includes the salient statistics on the production of pegmatite minerals other than quartz and feldspar; and brief descriptions of 170 specific pegmatite deposits.

Jan 1, 1966

By John M. Gomes

The preparation of tungsten carbide by molten-salt electrolysis was investigated. Sodium tungstate in the electrolyte and carbon from the graphite anode were the source materials, Optimum results were obtained with an electrolyte consisting of 83 mole-percent sodium chloride and 5.7 mole-percent each of sodium tungstate, sodium metaborate, and sodium hydroxide; a temperature of 1,000° to 1,025° C; an anode current density of 37 amp/dm2 or less; and an initial cathode current density of 150 amp/dm2. The yield was approximately 0.45 g/amp hr. The electrolytic tungsten carbide product contained approximately 5.4 weight-percent combined carbon as compared to 6.1 weight-percent for pure tungsten carbide. Microhardness of the electrolytic tungsten carbide, determined with a 50-gram load, varied from 3,480 to 3,970 dph. The material was friable and could be ground in a laboratory ball mill to less than 400-mesh particle size.

Jan 1, 1969

By W. M. Deaton

The formation of gas hydrates in natural-gas pipe lines depends on temperature and pressure conditions in the lines as well as on the presence of condensed water. The operating pressure in a pipe line may be determined easily and usually is available from the records of operation, but the temperature seldom is known. In cooperation with the American Gas Association, the Bureau of Mines, in its investigation of gas hydrates, conducted a pipe-line-temperature survey and studied underground temperatures at depths at which pipe lines ordinarily are buried and the relationship of these temperatures to prevailing atmospheric conditions. A similar but mere limited study of this type was conducted by engineers of the Bureau of Mines a number of yours ago.4/ A summary of the earlier findings was included in a general report by the Bureau on the flew of natural gas through high-pressure transmission lines.5/ In the present study, data on temperature variations were obtained at several places widely separated geographically. This information should assist pipe-line engineers in designing and operating natural-gas pipe lines.

Jan 1, 1941

By E. D. Gardner

"The Bureau of Mines receives many inquiries concerning favorable areas in which to prospect for gold, procedure to be followed, equipment required, and allied subjects. This circular has been prepared for use in reply to these inquiries.Interest in gold mining and prospecting for gold remains steady. From time to time many people take to the field to search for new gold deposits. A large percentage of them have had no previous experience in prospecting for lode gold; this paper has been written with the hope that it might assist these newcomers.A majority of the metal mines in the United States have been discovered by qualified prospectors who were searching for valuable minerals at the time. Chance, however, always has played a large part in finding mineral deposits. Some of the discoveries of the past were made by men on other errands, such as rounding up burros or hunting game. Accidental discoveries of ore bodies have been made in building roads and trails and in excavating for mine struc¬tures. Evidence of ore has been brought to the surface by burrowing animals and by ants; gold found in the craws of fowl has led to discoveries of deposits. Important discoveries have been made by men who had no knowledge of rocks or minerals; on the other hand, many ore bodies have been found by experienced prospectors, sometimes after hundreds of untrained men had already passed over the ground.The prospector who carries on his work diligently and intelligently is of course more likely to be rewarded for his efforts than the lazy or unintelligent worker; nevertheless, it is obvious that if valuable deposits are not present at the place being prospected none will be found. Conscientious and painstaking efforts to trace gold to its source usually disclose nothing more valuable than some narrow, unworkable seams; however, many deposits that were developed into profitable mines were found by this method of prospecting. Although some prospectors have made several lucky strikes, many others have spent their working lives searching for gold without finding anything worth while. Probably only one prospector out of several thousand ever finds anything worth developing. Moreover, only 1 out of every 300 or 400 properties developed becomes a profitable mine.Prospecting was begun in the Western States in the fifties as the miners looked for the source of gold found in placers. The search for gold has been continuous since that time; the number of prospectors in the field at any one time, however, has varied greatly. Except in some desert regions, practicallyall of the placer fields now being worked were discovered by old timers; more-over, most of the important gold districts were found by early prospectors. Important discoveries of lode mines, however, have been made from time to time. Most of the area in the mining regions of the West has been searched many times by prospectors, and nearly all of the easily found deposits have been located, but it is reasonable to expect that new gold mines will continue to be found. Most of the future discoveries undoubtedly will be of deposits that do not outcrop. Prospecting for such deposits requires considerable digging.Several important discoveries were made in 1934. One of these, the Rogers-Gentry gold mine at the edge of Antelope Valley in Los Angeles County, Calif., was found by an experienced prospector on an old patented homestead a number of miles from the nearest producing mine. The initial discovery at this mine was an iron-stained, decomposed, silicous limestone outcrop, with no vein structure evident at the surface, near a small, barren quartz outcrop and a water seep. Another discovery, the Silver Queen gold mine, in the same general region and near Mojave, Calif., was found by an experienced miner on an open fraction 400 by 1,400 feet in size between two old properties that were thought to have been worked out years ago. The Silver Queen discovery was made as the result of finding a"

Feb 1, 1950

By J. B. Gayle

Numerous investigators have studied the addition of inert4 substances to coking blends. Generally, the results have yielded trends applicable only to the particular coals and inerts studied. Recently, somewhat more general results were obtained for cokes produced from blends containing added inerts, using the sole-heated oven. The present investigation represents an extension of this work to include a wider range of inerts and to determine the applicability of the various conclusions to cokes produced with the Tuscaloosa oven. The results indicated that an increase in dry-coal charge density of 1 pound per cubic foot (p.c.f.) caused a corresponding change in the hardness (1/4-inch tumbler index) of Tuscaloosa oven cokes of 0.9 percentage points. This value compares favorably with the value of 0.7 determined previously for the sole-heated oven and Bureau of Mines-American Gas Association (BM-AGA) retort.

Jan 1, 1961

By J. J. Shields

This study by the Federal Bureau of Mines concerns different methods of face haulage used with various types of continuous-mining machines, mobile-loading machines, and track-mounted equipment under varying roof and bottom conditions and in coalbeds of varying thicknesses. This report is the ninth in a series on mechanical mining in bituminous coal mines. Reference to the reports previously published is made in appendix III, p. 106. Use of modern mining equipment in bituminous coal mines has resulted in increased productivity at the face. This especially is true where continuous-mining machines are used, and the supervision is good. Previous methods and equipment for moving coal from the face became inadequate and had to be improved to restore balance to the mining systems. Sometimes new equipment was needed to improve the face haulage, and in some instances, a new combination of existing equipment was used. Detailed studies of face haulage methods were made at 13 mines in Pennsylvania, West Virginia, Ohio, and Illinois to compare their effectiveness and to describe fully the conditions under which each method was used.

Jan 1, 1960

By Norwood B. Melcher

This report describes preliminary experiments by the Federal Bureau of Mines on the practicability of adding raw pellets of taconite concentrate to blast furnace feeds. The usual industrial practice is to harden the pellets by heating before they are charged to the furnace. The Bureau research demonstrated that raw pellets could be successfully smelted in an experimental furnace with no significant change in coke consumption and only a moderate increase in dust losses. The dust loss was 43 pounds per ton of metal for an all-pellet charge, compared with 7 pounds per ton for an all-sinter charge. Raw taconite pellets undergo only slight degradation during charging to the furnace if 1 percent bentonite is used as a binder. INTRODUCTION Fines and concentrates must be consolidated or agglomerated into larger masses before they can be smelted in a commercial blast furnace. Such agglomeration is usually done by sintering, pelletizing, nodulizing, or briquetting. Sintering has been the more common practice, but with the advent of taconite concentrates pelletizing is increasing in importance.

Jan 1, 1960

By P. F. Sands, Michael Sokaski, M. R. Geer

The purpose of this investigation was to determine the advantage of using either a conventional sieve bend ahead of a vibrating screen or of attaching a sieve - bend screen surface onto a vibrating screen to serve as a scalping deck when dewatering or draining dense medium from fine coal . In dewatering , use of either the sieve bend or scalping deck increased the capacity of the vibrating screen tenfold and the recovery of coal finer than 0.5 mm threefold , with no sacrifice in the moisture content of the oversize product . In dense -medium drainage , either the sieve bend or the scalping deck reduced the amount of magnetite retained on the product of the vibrating screen , particularly when the medium was as dense as that characteristic of the underflows from dense - medium cyclones . The sieve bend was slightly superior to the scalping deck in dewatering , but the scalping deck was clearly superior in dense -medium drainage . Additional advantages of the scalping deck are lower cost and a substantial saving in headroom.

Jan 1, 1963

By W. W. Agey

As a part of the program of investigation of domestic sources of manganese in the western United States, engineers of the Bureau of Mines examined. and obtained samples of ore from two properties in the vicinity of Barstow, San Bernardino County, Calif. In addition to these, samples from two other properties in the same vicinity were submitted by the owners. As the ores were too low-grade to be acceptable for the direct production of ferromanganese, beneficiation studies were made to determine the amenability of the ores to concentration by ore dressing. The Big Reef manganese claims axe about 140 miles east of Barstow, Calif. The claims were leased by W., E. Thurber of San Gabriel, Calif., from the owner, C. S. VanDoren of Daggett., Calif. Manganese oxides occur as a replacement deposit in heavily brecciated andesite along a fault plane. Four samples were taken by an examining engineer of the Bureau of Mines from the ore zone, which, when composited, were representative of all the exposed ore. Preliminary tests were made on lot B, and final tests wore made on the composite sample. The Trans-Oceanic property is about 20 miles southeast of Barstow, near Newberry, in the. Pisgah mining district, Calif. The sample, submitted by the owners, was taken from a 1,000-ton reject clump from a hand-sorting operation. The ore occurs as a replacement of rhyolite.

Jan 1, 1952

By Je M. Oh

The U.S. Bureau of Mines is conducting research on the oxidation resistance and structural stability of Fe-(0-8)Cr-(0-16)Ni-(0-16)Mn-3.5Si-lAl alloys as potential substitutes for high-Cr stainless steels. Oxidation tests were conducted in air over the temperature range of 6000 to 9000 C for up to 1,000 h. Microstructures were analyzed at room temperature after hot rolling. The oxidation properties and the structural stability were found to be greatly affected by the Cr and Mn levels. Although substitution of Mn for Ni increased the oxidation rate, the Mn helped to stabilize the austenitic microstructure. Decreasing the Cr content or increasing the Mn content produced higher oxidation rates and earlier oxide spalling. In this study, reaction kinetics, oxide morphologies, and microstructure of the alloys were investigated using scanning electron microscopy, energy dispersive X-ray analysis, X-ray diffraction, and electron microprobe analysis.

Jan 1, 1989

By Robert Merritt

Approximately 2,500 tons of low-grade uranium ore were used to conduct a field-scale heap leaching test as well as throe column leach tests. The ore used to construct the field-scale heap leaching test had a grade 0.023% U308 while the ore used fur column leach tests had a grade of 0.027% U308. The ore was crushed to minus 4 in. The field-scale heap was constructed on a clay base with parallel effluent lines running under the heap spaced 7.5 ft apart. The heap was leached for 45 days, drained, washed, and dismantled. Based on residue analysis, approximately 205 tons of ore were leached with a final U308 extraction of 96%. The heap was 17.9 ft in height and leached in a near-vertical pattern down to approximately 1 ft, at which point the leached zone become bell-shaped. Two 8-ft column charges and one 18-ft column charge were leached for 36 and 45 days, respectively. Based on residue analyses, all U308 extractions were greater than 96%. The conclusions generated by the studies showed that (1) flow rates were similar for column leaching and field-scale leaching, (2) final U308 extractions were the same for both types of leaching; however, the deeper ore beds tended to require longer leaching times, and (3) the reagent requirements were reduced with increased bed depth.

Jan 1, 1980

By Özgen C. Karacan

It is generally accepted that typical coalbed gases (methane and carbon dioxide) are sorbed (both adsorbed and absorbed) in the coal matrix causing it to swell and resulting in local stress and strain variations in a coalbed confined under overburden pressure. The swelling, interactions of gases within the coal matrix and the resultant changes in the permeability, sorption, gas flow mechanics in the reservoir, and stress state of the coal can impact a number of reservoir-related factors. These include effective production of coalbed methane, degasification of future mining areas by drilling horizontal and vertical degasification wells, injection of CO2 as an enhanced coalbed methane recovery technique, and concurrent CO2 sequestration. Such information can also provide an understanding of the mechanisms behind gas outbursts in underground coal mines. The spatiotemporal volumetric strains in a consolidated Pittsburgh seam coal sample were evaluated while both confining pressure and carbon dioxide (C02) pore pressure were increased to keep a constant positive effective stress on the sample. The changes intemal to the sample were evaluated by maps of density and atomic number determined by dual-energy X-ray computed tomography (X-ray CT). Early-time images, as soon as CO2 was introduced, were also used to calculate the macro porosity in the coal sample. Scanning electron microscopy (SEM) and photographic images of the polished section of the coal sample at X-ray CT image location were used to identify the microlitho types and microstructures. The CO2 sorption-associated swelling and volumetric strains in consolidated coal under constant effective stress are heterogeneous processes depending on the litho types present. In the time scale of the experiment, vitrite showed the highest degree of swelling due to dissolution of CO2, while the clay (kaolinite) and inertite region was compressed in response. The volumetric strains associated with swelling and compression were between ± 15% depending on the location. Although the effective stress on the sample was constant, it varied within the sample as a result of the intemal stresses created by gas sorption-related structural changes. SEM images and porosity calculations revealed that the kaolinite and inertite bearing layer was highly porous, which enabled the fastest CO2 uptake and the highest degree of compression. Keywords: Coal; Carbon dioxide; Sorption; Swelling; Sequestration; X-ray computed tomography; Volumetric strain; Gas outbursts

By C. W. Owings, J. J. Forbes

"INTRODUCTION The recent coal-dust explosions in Illinois and Indiana have again brought forcibly to the attention of mining men the fact that mines which liberate little or no methane can have widespread explosions, if dry and dusty conditions exist and if adequate measures are not taken to control the dust hazard by rock dust¬ing or use of water.Even though rock dust has been used more or less extensively for more than 20 years as a means of limiting or preventing coal-mine explosions, many mine operators have requested information on rock dusting and means of allaying coal dust at its source. The purpose of this circular is to summarize available information on these two methods.COAL MINES TO BE ROCK-DUSTEDAll nonanthracite coal mines must be rock-dusted, except those mines or locations in a mine that are too wet or too high in incombustible content to propagate an explosion.Coal dust that contains 20 percent or more moisture may prevent ignition or propagation of an explosion. Such dust can be molded in the hands, and under such condition the roadway would be considered muddy. Mine dust that is only damp is not wet enough to prevent propagation of an explosion. Beads of water standing on accumulations of dust are not indications that the dust is wet. Only those mines or locations in a mine in which the coal dust can be molded in the hand need not be rock-dusted."

Jun 1, 1947

By W. K. Overbey

The Bureau of Mines conducted surface joint and stress measurements, airborne remote sensing imagery studies, compass-oriented borehole televiewer surveys, numerical simulation of fractured wells, and well productivity studies in a four-quadrangle study area of Ohio, to determine the effects of earth fracture systems on the deliverability of gas storage fields. The results of these studies indicate that much useful information about a gas storage reservoir can be obtained and put to practical use by studying--(1) oriented cores for fractures and directional permeability, (2) orientation of induced hydraulic fractures for alignment of well patterns, and (3) aerial photos and multispectral scanner imagery for general surface geology comparison and to determine if some, development patterns can be generated by such results. The absence of known tectonic elements associated with flat-lying sediments, such as faults or fracture zones that can be seen on the surface, indicates that the use of remote sensors such as radar or aerial photography is not likely to be useful in picking well locations for drilling. Studies similar to those discussed here should be conducted in gently folded and strongly folded sedimentary formation areas to determine if the increased knowledge of earth fracture systems under these conditions might be beneficial in gasfield and gas storage reservoir development.

Jan 1, 1974

By Christopher Mark

Australia and the United States both have large, modern underground coal mining industries. Many companies have invested in both countries, and there is growing awareness that technological developments in one country can rapidly affect the other. Yet the ability of technology to pass between the countries depends on comparability of ground conditions. Many Australian observers believe that their ground conditions are significantly poorer than typical U.S. conditions, but some U.S. professionals are not convinced. The author recently visited 10 Australian longwall mines and two room-and-pillar mines. Each mine visit included determination of the Coal Mine Roof Rating, roof support installed, pillar design, and an in-depth discussion of ground control experience. The Australian conditions observed are compared with an extensive data base from U.S. mines. The paper also offers observations on geotechnical data collection, monitoring, and the roles of the mine inspectorate and research community.

By W. D. Kaiser

Recent legislation and expected future legislation is aimed at reducing the dust levels developed in underground coal mines. Several techniques for reducing dust levels are being evaluated. One of these is the modification of cutting parameters such as feed rates, cutting speeds, and pick configurations in order to reduce the amount of dust generated. In order to evaluate the feasibility of modifying cutting parameters to reduce dust, the Bureau of Mines commissioned Battelle to construct a small scale mining machine which could be used for evaluating the effects of those changes in cutting parameters. Specific features of this machine were that it should be highly instrumented to measure various cutting parameters, should have a wide range of feed and speed controls, and it should be possible to vary the pick configurations and geometries on the machine. In addition, it was desired that this machine should have cutting capabilities which greatly exceed present coal mining practice and also that the unit should be small enough and portable enough that it could be taken into and out of operating coal mines with a minimum of interference with the normal coal mine operations. The first step in constructing a machine to meet these requirements was to determine the cutting forces and approximate sizes of components which would be required to cut at the speeds and feeds specified by the Bureau of Mines. Initial calculations using; published data on cutting forces indicated that cutting forces in the neighborhood of 5,000 lbs and power levels of approximately 30 horsepower would be adequate for the application. However, further data developed during the course of the project indicated that when low efficiency picks are used, cutting forces and powers can be two to three times as high as these initially estimated values. After several design iterations, a design was chosen in which the cutting head was driven by four hydraulic motors which were part of a hydrostatic transmission which, in turn,

Jan 1, 1973

By A. W. Khair, M. Ahmad

"Bit wear has been proven to have a significant effect on respirable dust generation in coal cutting system. The mechanism of bit wear can be adhesion, abrasion. oxidation, or diffusion. depending on cutting conditions. This paper presents a portion of an extensive ongoing series of studies to better understand the principles of bit wear and dust generation. Used bits collected from underground coal mines were analyzed to identify the basic principle of bit wear in coal and rock cutting. Distribution of weight loss and conical height loss of worn bits were studied and bit wear was divided into four stages according to weight loss. Utilizing these worn bits, Laboratory experiments have been carried out to study the effects of bit wear on coal cutting system and respirable dust generation. An Automated Rotary Coal Cutting Simulator was use to perform the experiments. Acoustic emission monitoring is applied to study the effect of bit wear on fracture formation and dust generation. INTRODUCTIONContinuous miners were introduced in the 1950’s and became the major equipment in underground coal production. Now the larger production in the coal industry has increased the demand for continuous miners and their use. It is well known that serious dust problem is also introduced with the use of continuous miners, especially with recent increase in productivity. On the other hand, legal restrictions are made ·more strict by the Mine Health & Safety Administration for the respirable dust generated by the continuous miners to prevent coal workers from incidence of pneumoconiosis. The incidence of pneumoconiosis depends on dust concentration, exposure time, and physical properties of dust. Of them, dust concentration is the best parameter for the assessment of the risk of pneumoconiosis. Although a lot of research work has been done to reduce dust concentration substantially, some areas are still required further investigation to meet the strict regulations. One of the areas is about bit wear and dust generation. In this area, the principles of bit wear and effect of bit wear on dust generation are major concerns."

Mar 1, 1992