Search Documents

By Edward P. Barrett

[Iron oxides, when reduced at temperatures below 900° form a dark gray substance, very porous bait otherwise in almost the same form as the original particles. In the temperature ire range of 1,000 to 1,100° the product is pertly sintered but still shows the outlines of the original particles. Those products are known as "sponge iron." At temperatures of 1,100 to 1,2000 the metallic iron begins to flow together and to a semifused, pasty, porous mass called a "bloom," which can he worked under a hammer to form a product similar to wrought iron; it contains slag inclusions and is too low in carbon to make steel. If the temperature is 1,300 to 1,300°, part of the iron will fuse enough to absorb more carbon. The dissolved carbon lowers the melting point and still more carbon is absorbed. The melted portion acts a flux for the unmelted metallic particles until the entire mass becomes a high-carbon fluid known as "cast iron." Sponge iron was probably the form in which the first iron was recovered from the ores. As early as the eighth century the Catlan forge3 developed into a low-shaft furnace known as the "high bloomary," in which iron eras produced in the form of a pasty mass. In 1340 the first blast furnace was built in Belgium. The greater part of the iron was made into wrought-iron blooms by crude puddling processes. Charcoal was used as the fuel until tie latter part of the 17th century when coke was used in England. In 1865 Bessemer built his first converter in. England, and within a few years the Siemen's regenerative open-hearth furnace was developed, also in England. Enormous expansion in the metallurgy of iron followed. The idea of "direct processes" for the production of iron arid steel has persisted throughout all this time. The production of steel from sponge iron has theoretical advantages over the present-day standard methods, and handreds of so--called "direct processes" have been proposed or tried during the past century.4]

Jan 1, 1929

By Michael G. Zabetakis

Investigation of gas explosions usually reveals that the combustible gases have come from transmission and storage facilities or from natural gas or oil wells. However, combustible gases such as methane and hydrogen can derive from biological processes. Hazardous situations have been created in the past by the use of abandoned mines for the disposal of sewage and rainwater, by the interconnection of storm and sanitary sewers, by sealing the openings in manhole covers when repaving the roadway over a sanitary sewer, and by the construction of buildings over or near garbage fill areas without adequately providing for the release of combustible gases.

Jan 1, 1962

By Charles E. Whieldon

This report presents the results of a study on part of the Smithfield oilfield, Wetzel County, W. Va. The primary purpose of the investigation was to determine the original and the present volume of stock-tank oil in the formations and to investigate the feasibility of waterflooding the Gordon Stray, Gordon, and Fourth sands underlying the I. D. Morgan lease. The study was based on laboratory core analyses, geophysical well logs, geologic considerations, and various field prediction data from the I. D. Morgan lease. The Bureau found that, of the three sands cored, the Gordon Sand was the best prospect for waterflooding, and that a properly engineered water flood should recover 136 to 230 barrels of oil per acre-foot from this formation.

Jan 1, 1967

By Robert L. de Beauchamp

The Bureau of Mines designed a chlorination apparatus to prepare CrCl2 free of CrCl3 by the direct reaction of chlorine and chromium. Equipment and procedures were developed for routine preparation of 25-pound batch quantities of anhydrous CrCl2. Calcium, iron, nickel, and silicon impurities were in the 0.01 to 0.05 percent range, and all other impurities were below 0.01 percent.

Jan 1, 1968

By Steve Signer, Ed Mchugh

Recent studies by researchers from the National Institute for Occupational Safety and Health indicate that shear loading contributes significantly to failure of bolts used for rock reinforcement in coal mine roofs, Laboratory tests on 17 bolts were conducted to study the behavior of roof bolts subjected to shear loading over a range of axial bolt loads, Fourteen strain gauges were attached to each bolt to measure axial and bending loads at seven locations along its length. The instrumented bolts were grouted through two high-strength concrete blocks, and axial tension was applied to as much as 75% of yield strength. With the block interface acting as a failure plane, shear loads were applied to the blocks at a constant rate of displacement to the ultimate strength of the bolts. The tests characterized the relationship of axial bolt loads to shear forces across a rock bedding plane and measured the distribution of axial and bending strain along the length of the bolts. 'These results will improve the selection of roof reinforcement in mine areas where high shear stresses are present, thus improving the safety of miners working in these areas.

By M. A. Elliott, H. H. Schrenk, L. B. Berger, John C. Holtz

"INTRODUCTION Among the hazards that may attend the use of Diesel engines in mines, tunnels, or other underground operations the presence of harmful or objectionable constituents in the exhaust gas must receive due consideration to prevent the formation of unsafe or unhealthful working environments in these places. Previous reports of this series have presented discussions of the composition of exhaust gas from engines in proper mechanical condition, 6/ the effect of adding some of the exhaust gas to the intake air of the engine, 7/ the effect of operation in atmospheres containing natural gas, 8/ and the effect on exhaust-gas composition of conditions that influence the characteristics of fuel injection in Diesel engines. In all these studies the properties of the fuels used were in general conformity with specifications usually recommended by the manufacturers of Diesel engines. In evaluating the physiological significance of the various components of the exhaust in these experiments, the toxic or objectionable gases determined were carbon monoxide, carbon dioxide, oxides of nitrogen, and aldehydes. Because of the low sulfur content of' these fuels, compounds such as sulfur dioxide and sulfur trioxide were not determined, although in discussion of the test results attention was directed to the fact that if fuels of higher sulfur content were used, the concentration of such compounds in the exhaust would become a significant factor in establishing the quantity of ventilating air required to furnish satisfactory dilut1on of the exhaust gas in underground working places."

Jun 1, 1943

By D. D. Runnells

This study focused on the chemical reactions between uranium tailings fluids and cores of subjacent bedrock from the site of the Cotter Corporation uranium mill at Canon City, Colorado. Actual and synthetic tailings fluids were forced through cores of bedrock. The pH of the effluent solutions was the dominant control on the behavior of dissolved species in solution. The pH depended on the presence or absence of calcite cement in the rocks. Calcite neutralized acidic raffinates and caused the precipitation of iron, manganese, aluminum, and possibly uranium. Chloride, sulfate, and sodium were not retarded upon passage through the cores, and sulfate and chloride should be useful as tracers of escaping tailings fluids. Zinc, copper, cobalt, nickel, uranium, and vanadium exhibited high mobility under acidic conditions and were strongly retarded at elevated pH. Calcium was released due to dissolution of calcite and ion-exchange. Magnesium was not retarded in concentrated solutions, but showed moderate retardation in dilute fluids. Potassium and ammonium both showed early retardation followed by breakthrough and mobility. The behavior of molybdenum was strongly dependent on pH, with retardation at low pH and mobility at elevated pH. Selenium was highly mobile under all conditions. Selenium should be a better tracer than molybdenum for many situations. Precipitation of carnotite appears to control the solubility of uranium and, possibly, vanadium. With the exception of the precipitation of aluminum and silica, all reactions were rapid.

Jan 1, 1983

By W. M. Weigel

"The use of sand for the filtration of municipal water supplies is comparatively recent use in this country, although at the present time, most cities of any size that draw their water supply from surface sources use sand filters in their purification system. Not only are sand filters employed to remove sediment and suspended matter, but they also take out most of the bacteria in the water.The first comprehensive research and study of sand for this purpose was probably that of Hazen for the Massachusetts Board of Health in 1891 and 1892, although sand filters had been employed for a considerable time before, specifications for filter sand drawn since then have been largely based on the results of Hazen's work,The general requirements for filter sand are more exacting than for any of the different kinds of sands, except the chemical specifications for glass sand. Filter sand must be uniform in size and within certain limiting sizes. In addition, it must be clean and free from clay and organic matter and of fairly high purity. Early investigations established the fact that an excess of fine materiel increased the friction and decreased the rate of flow through the filter, and that the size of the finer particles rather than the courser, determined the effective size. Also, that large grains tended to cause irregularities in flow in different parts of the bed. There is no requirement as to grain shapes, except that they be not flat or elongated, since, so far as known, either rounded or angular grains are equally efficient.Based on Hazen's investigations, two factors are quite generally used to control the average size and uniformity of size of the sand. These are defined as follows: The ""effective size"" of a sand is such that 10 per cent by weight of the seed is finer than this size, end 90 per cent is coarser. It is expressed in millimeters, The ""uniformity coefficient"" is defined as the ratio of the size of grain which has 60 per cent finer than this size to the size which has 10 per cent finer (the ""effective size""). It is evident that the smaller this coefficient, the more uniform is the seed. If all the grains were exactly the same size, the coefficient would be 1."

Jul 1, 1924

The principle activities of the Explosives Research Laboratory from July 1, 1961 to June 30, 1962, are described briefly in part 1. Part 2 gives short abstracts of publications that appeared during fiscal year 1962; in general, the research reported in these publications antedates the report period. Part 3 gives the results of an investigation which, although too limited to warrant separate publication, merits presentation in some detail because of current interest in ammonium nitrate-fuel oil compositions.

Jan 1, 1964

By Elton L. Litchfield

The techniques for direct initiation of detonation, developed by the Bureau of Mines, have been applied to gaseous mixtures of oxygen with methane, 'thane, propane, butane, or hexane. An exploding wire was used as the initiation source to determine minimum stored electrical energies required to effect detonation of mixtures between one-half and two times the stoichiometric fuel ratios. Detonations were obtained in the most easily initiated mixtures of ethane, propane, butane, and hexane for initiation energies between 24 and 33 joules at 1 atm and 28-43 joules at 0.5 atm initial pressure. Methane mixtures, at 1 atm, were not observed to detonate when initiated with up to 484 joules.

Jan 1, 1966

By Ivan L. Nichols

Tailings dumps at Mercur, Utah, contain about $7 million worth of gold in 3.5 million tons of mill tailings assaying about 0.07 ounce of gold per ton. Commercial mining and milling at Mercur ceased in 1942. To determine whether improved technology was now available that might permit economic reprocessing of the Mercur dumps, the Bureau of Mines probed for a low-cost method that would be applicable to these tailings. A composite sample prepared for laboratory studies assayed 0.062 ounce gold per ton. About 10 percent of the gold occurred as a water-soluble cyanide. Conventional cyanide leaching dissolved 32 percent of the gold, and hot, strong cyanide solution dissolved 42 percent. Results were not improved by pretreatment with acids, bases, or oxidants. After expensive preroasting, gold recovery by cyanidation was increased to 65 percent. The simple procedures were ineffective, and more effective procedures were too costly for economical processing of Mercur tailings.

Jan 1, 1970

By Burton Scott

A device for detecting carbon monoxide at ppm levels is described which is based on the measurement of infrared absorption at 4.65 microns. The unique feature of the nondispersive infrared instrument is contained in the optical design which includes a confocal cavity, increasing the effective optical path length by a large factor, thus greatly reducing the required package size. The cavity has the effect of reducing the total amount of radiation passing to the detector, but at the same time increasing the percent attenuation observed when adding CO, by a factor called gain. The radiation is chopped by a filter wheel which contains narrow band filters at 4.0 and 4.65 microns. The resultant signal produced by the pyroelectric detector is demodulated by the electronics to product an automatic gain control signal, proportional to the total radiation, and a difference signal, proportional to the CO present. Tests of a breadboard model are described which show cavity gains of 10 with noise levels equivalent to 2 to 10 ppm CO.

Jan 1, 1975

By Theodore Kessler

The purpose of this Bureau of Mines investigation was to determine what new organic compounds or high concentrations of a particular organic species can be formed by exposure of coal derivatives to ultrasonic energy. Tetralin, l-methylnaphthalene, and pyridine were used as model compounds. Gaseous and solid reaction products resulting from the ultrasonic irradiation of these coal derivatives were determined using mass spectrometry. Products from the irradiation of tetralin were studied as a function of time, atmosphere, and sample size. The sonolysis (chemical reactions produced by ultrasonic energy) of tetralin and l-methylnaphthalene produced C2H2, HCN, CH4, H2, CO, and CO2, depending upon the experimental conditions. The ultrasonic irradiation of tetralin also produced diacetylene under certain experimental conditions. The cleavage of organic chemical bonds by ultrasonic cavitation in the absence of water was also observed in this study.

Jan 1, 1967

By A. R. Rule

This report describes preliminary studies by the Bureau of Mines to develop a procedure for extracting the fluorine from low-grade fluorspar ores in which the CaF2 particles are finely locked in the calcite matrix. A combination of flotation beneficiation and pyrohydrolysis is applied to recover and to liberate the fluorine. Flotation of a finely locked high-calcite fluorspar ore containing only 11.7 pct CaF2 recovered over 92 pct of the fluorspar at a grade of 51 to 52 pct CaF2. Pyrohydrolysis of the flotation concentrate liberated nearly 90 pct of the fluorine as aqueous HF. By this procedure over 80 pct of the fluorine contained in the original ore was extracted.

Jan 1, 1974

By Ernesto Villaescusa, Andres Brzovic

Rock masses of the primary copper ore at the El Teniente Mine are very competent and massive. The rock mass contains almost no open discontinuities. Nevertheless, there is a high frequency network of small discontinuities coupled with widely spaced faults. A data collection campaign designed to characterize the rock structure was recently implemented. The results show that conventional analysis in terms of discontinuity frequency does not predict differences between two studied sectors. However, when an empirical definition of a weak discontinuity is applied, appreciable differences between the two sectors appear in terms of discontinuity frequency and predicted in situ block size distributions. These differences are in accordance with actual observations at the mine site. Due to the geological features of the primary copper ore, rock mass classification schemes cannot be readily applied to characterize these rock masses.

Jan 5, 2007

By L. H. Lange, F. F. Hintze

"Mineralogical Composition of Cyanite RockIn the group of minerals used in making this study, the cyanite is associated with quartz, mica, and feldspar in the schist. The amount of quartz is variable, but it is always an abundant mineral. Both large and small crystals of quartz occur in irregular masses, rarely ever showing crystal outline. Mica is of the clear and dark varieties the larger crystals being dark as a rule, and the finer crystals of light color, The present mineralogical composition of the mica is rather variable as most of the original biotite and muscovite have suffered alteration, and much secondary mica is present as a result of alteration of the original mica and other minerals present, especially the larger cyanite crystals. A large part of the mica now found in the ore is chlorite, with varying amounts of Jefferisite and others, especially sericite. These are in the form of aggregates, or felt-like intergrowths filling the spaces between the quartz, cyanile, and feldspar.The feldspar is plagioclase probably mostly albite. It is white, possesses good cleavage, and is one of the hard brittle minerals of the rock. It alters to kaolin, and sericite, and more or less of these alteration minerals are present within the feldspar crystals but not separated from them.The cyanite is of two varieties, distinguished by their colors as blue and white cyanite. The blue color varies in intensity, being a pronounced blue in some crystals and paler in shade in others. Some crystals have been seen which possess the blue color in one-half of their mass and are pure white or clear in the other half. The purity of the cyanite is probably not affected by the color, but it is difficult to detect the white cyanite in the ore by macroscopic examination, so that great care has to be exercised in the selection of the ore in the field."

Apr 1, 1931

By Noel N. Moebs

The Bureau of Mines investigated severe coal mine roof support problems along a section of main entries in the Pittsburgh coalbed in southwestern Pennsylvania to identify the causative factors. The mine roof was examined in detail, and various sedimentary structures are described that contributed directly to irregular and unstable roof. Small-scale paleochannels, scours, and related slickensides were identified as the leading cause of bad roof, and isopach maps were prepared to illustrate a method whereby the presence of these structures could be inferred in advance of mining. Probably second in importance was the occurrence of relatively incompetent flaggy, poorly cemented sandstone, weakened by coal and micaceous laminea. No effect of in situ stresses on roof stability was detected.

Jan 1, 1977

By John L. Morning

Although faced with a slowdown in the world economy, continued inflation, and rising costs, the mining industry exceeded its 1974 raw mineral production value of $55.1 billion by 13%. The increase was due to value increases in the production of fuels and nonmetals; metals reported a decrease in value. Of 23 metals produced, 14 showed value increases; of 44 non-metals produced, 26 reported value in-creases. Because of increasing costs and depletion of high-grade reserves, the mining industry continued to rely on new technologies to maintain its profit margins. In the surface mining sector, the development of new tools and equipment played a large part in increasing production and maintaining this goal. Some of the types of equipment developed were instrumentation for control of pit slope stability, shovel power transmissions, electric wheel trucks, and single-flight conveyor systems.

Jan 1, 1977

By Frank T. Duda

A U.S. Bureau of Mines interactive FORTRAN computer program can screen explosion-proof enclosures intended for underground service. The program incorporates important information and criteria to assist enclosure manufacturers and Mine Safety and Health Administration (MSHA) personnel by providing a first-order approximation of rectangular explosion-proof enclosure characteristics prior to actual certification testing. The program uses information and data that can be retrieved automatically during program execution. The program also performs the calculations for a series solution algorithm and various equations to evaluate the enclosure for both a static internal pressure and an internal explosion. The program writes the intermediate and final calculations and information concerning the status of the screening process to a summary file on a floppy disk. One data base contains MSHA certification requirements given in the Code of Federal Regulations (30 CFR 18). A second data base contains material properties of acceptable construction materials and weld joint efficiencies. A series algorithm determines bolt and cover stresses for a simply supported rectangular cover with arbitrary bolt locations. Limit and yield line analysis is used to calculate the strength of body panels.

Jan 1, 1989

By R. L. Rough

Photoelastic, wire resistance, and borehole-deformation gages were used to measure the in situ strains when an outcropping Black Hand Sandstone Formation in Hocking State Forest, Hocking County, Ohio, was overcored to stress-relieve the surrounding sandstone. Strains transmitted to the photo-elastic gage did not produce isochromatic patterns suitable for quantitative analysis. Strain readings from the wire resistance gage indicated tensile-strain loading during overcoring; readings from the strain-gage bridges in the borehole-deformation gage indicated compressive-strain relaxation during overcoring. The magnitude and orientation of the computed stress fields obtained from both gages were comparable when the corresponding tensile and compressive elastic moduli were applied. Stresses computed from deformation and resistance gages at depths to 5 feet showed the maximum stresses to range from 1.042 to 2.121 times greater than the minimum stresses. The bearings of principal stresses calculated from the deformation gage readings varied between N 61° E and N 83° E; the wire resistance strain gage bearing computations varied between N 68° E and N 82° E. Measurements of in situ strain in sandstone were shown to have promise but to require further development in field technique that could likely be achieved through experience.

Jan 1, 1971