Search Documents

Objective: To identify and evaluate a durable, flexible, and practical stopping to direct ventilation airflows in large-opening metal/nonmetal mines.

May 1, 2006

By Ann G. Kim

Methane in coal constitutes a serious hazard during mining. Draining the methane from large blocks of coal in advance of mining is an effective method of improving the safety and efficiency of coal mining. Because of the similarity of the two gases, drained methane can be recovered and added to pipeline supplies of natural gas. To effectively apply advance drainage techniques and recover drained gas, a gross estimate of the methane content of coal is necessary. Using data from previous investigations, the virgin reserves of the Pittsburgh coal in the central and southwestern parts of Washington County, Pa., are estimated at over 1.5 billion tons, with a methane content of 50 to 100 fts/ton. The Pittsburgh bed in this area of approximately 265 mi2 contains over 130 billion ft3 of methane.

Jan 1, 1974

By V. C. Petersen

The titanium-rich end of the titanium-germanium system was investigated by x-ray and metallographic methods and verified by resistivity and dilatometer measurements. A constitution diagram is proposed. The titanium-rich portion of the phase diagram is characterized by eutectic and peritectic reactions. The eutectic composition is 19 percent germanium, and the eutectic temperature 1,360° C. The peritectic reaction occurs at 905° C. and 4 percent germanium. Germanium is soluble in alpha titanium to a maximum of 4 percent at 905° C. and in beta titanium to a maximum of 12.5 percent at 1,360° C. Both limits of solubility decrease with decreasing temperatures. Although substantial quantities of germanium are soluble in beta titanium, beta is not retained on quenching. The beta phase probably transforms to alpha by a martensitic reaction.

Jan 1, 1957

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

MINE VENTLATION NETWORK ANALYSIS

Jan 1, 1977

By Fred N. Kissell

The U.S. Bureau of Mines was established in1910 to reduce .the high accident rate in the nation's coalmines. For 85 years, it conducted a wide variety of tasks related to mining before it was abolished in 1995. The BOM had many technology transfer successes in its lifetime, including more than a dozen "R&D100" awards. This essay identifies and discusses five "transfer factors" that can explain the success (or failure) of many Bureau of Mines projects. These five factors are termed "pressure, pitfalls, path, price, and profit."

By Harold L. Rhodes

Vapor-liquid equilibria data for 65-34-1 and 25-27-48 mole percent helium-nitrogen-methane mixtures are presented for 12 temperatures from 76.5° to 164° K and pressures from 100 to 1,200 psia. These data were obtained in a windowed phase equilibria cell equipped with a vapor recirculating pump. Isobaric and isothermal K-values are plotted for both mixtures. Two isometric plots are included.

Jan 1, 1972

By William H. Schiffbauer, William D. Mayercheck, August J. Kwitowski

This report summarizes work sponsored by the Bureau of Mines in the development of a remote operating system (ROS) for controllng a thin-seam continuous miner (TSCM) 500 feet or more distant from the extraction face. Detail s are provided on ROS subsystems including the continuous miner, video equipment, controls and displays, the electronic control system, and the operator station.

By Kevin Connor

The Government's ban on all commercial mining operations, except for small-scale artisan exploitation of alluvial gold deposits, continued throughout 1985. Minerals produced were kaolin and lime for agricultural uses, and experimental peat harvesting for energy applications. The total value of the minerals produced during the year was estimated at $1.1 million .2 In early 1985, an agreement between the Government and Amoco International Oil Co. was ratified for a petroleum exploration concession covering 248,000 hectares of Lake Tanganyika. Onshore exploration in the Ruzizi Plain was already under way the last half of 1985. By yearend, enough seismic information was available that Amoco hoped to complete data analyses, determine onshore drilling sites, and begin drilling operations before the end of 1986. Also to begin in the latter part of 1986 were seismic studies of Lake Tanganyika. Throughout 1985, Amoco officials were negotiating with the Government of Zaire for expanding the exploration acreage into that country's portion of northern Lake Tanganyika and the Ruzizi Plain. An agreement between Amoco and Zaire could have important beneficial economic implications for both Zaire and Burundi, and onshore seismic work in Zaire logistically supported from Bujumburi could begin almost immediately.

Jan 1, 1987

By Joseph B. Huvos

Said to be one of the world's most under-developed countries, Benin had a gross national product (GNP) estimated at $1 billion in 1980.2 Contribution of the mineral industry such as cement and limestone to the GNP was negligible, but exploration of mineral potential continued Minerals.-The United Nations Development Program (UNDP) conducted an investigation of three deposits from 1977 to 1980: Phosphates (Mekrou), gold (Perma), and chromite (Buem). A phosphate rock deposit containing about 4.5 million tons recover- able by opencast techniques was discovered. It was not known if the gold and chromite deposits were recoverable economically. Iron ore deposits of some 230 million tons near Loumbo-Loumbo are at present not exploitable because of lack of infrastructure in the northern part of the country. Geologic mapping with British and French assistance was also pursued in 1980.

Jan 1, 1982

By Franklin D. Cooper

This chapter includes tables for 1979 that were not available in time for publication in the 1978-79 Minerals Yearbook, but it does not include corresponding tables for 1980. The value of raw nonfuel mineral output in 1980 was estimated at $24.8 billion, 8.5% above the 1979 value. Of the 21 metal commodities produced, quantitative output increased for 11 and decreased for 10. The values for 10 metals were up, 10 were down, and 1 was unchanged. Among the 47 non-metallic commodities produced, 14 showed quantitative increases, 32 declined, and 1 was unchanged. In terms of value, 32 nonmetallics increased, and 15 declined.

Jan 1, 1981

Develop a technology for producing high-quality hake graphite from the steelmaking waste known as kish. Approach Treat the waste kish as an ore and apply mineral processing techniques of physical beneficiation and chemical purification to produce a range of graphite products com¬petitive with the natural mineral. Background Graphite is a naturally occurring form of carbon with a unique combination of properties that make it indispensable in a very wide range of industrial and consumer applications. It has high electrical and thermal conductivity and remains stable to extremely high temperatures It has a low coefficient of friction and is nearly impervious to corrosion. The steel industry is dependent on graphite in clay-, magnesia-, and alumina-bonded refractories for crucibles, bricks, facings, and coatings. Electrical uses include graphite brushes in motors and generators, and electrodes in batteries. The transportation industry needs graphite for clutch and brake linings, and all industries depend on graphite in seals, gaskets, lubricants, and coatings. The consumer sees graphite in composite plastics and in the common pencil. As with all natural minerals, the availability of graphite is diminishing and costs are rising as quality decreases.

Jan 1, 1993

By Ralph B. Adair

The Bureau of Mines conducted laboratory batch and small-scale continuous tests on samples of silt from the Nolichucky Reservoir near Greeneville, Tenn., to develop a process for the recovery of commercial-grade muscovite concentrates. Using a combination of Humphreys spirals for preconcentration followed by cationic flotation, 94.5 percent of the muscovite was recovered in a product containing 96.5 percent muscovite.

Jan 1, 1971

By D. A. Doughty

The Bureau of Mines developed two methods for determining iron II and iron III in 2- to 5-mg samples of coal using electron paramagnetic resonance (EPR) spectrometry. One method used solid coal samples; the other method used aqueous solutions. The method using solid samples was more simple, technically, but required the use of X-ray fluorescent analysis, or another independent method, for determining total iron in the samples, and the results were subject to some uncertainty. The method using aqueous solutions appeared capable of greater certainty and did not require additional methods of total iron analysis but was more involved procedurally. The coals analyzed were found to contain much more iron II than iron III.

Jan 1, 1973

By R. Agarwal

The in-situ stress field was determined, using the overcoring technique, at two underground sites at the Pea Ridge Mine, Sullivan, Missouri. At one of the sites in magnetite, the three dimensional stress field showed the largest principal stress to be compressive (-4564 psi), nearly horizontal and closely parallel to the strike of the orebody. The smallest principal stress was also compressive (-2047 psi) and nearly vertical. Considerable difficulty was experienced in drilling porphyry rock at the second test site in the host rock. Only one hole was drilled at this site. The secondary principal stresses obtained in the porphyry are -9464 and -4945 psi, respectively. The-test site in magnetite is located at a depth of 2505 feet whereas the site in porphyry rock is at 2475 feet. The vertical stresses: due to overburden loading at these sites are -3590 and -2782 psi, respectively. Field determined values of the vertical stress are -2207 and -5098 psi, respectively. The variance; between the two sets of values is most likely attributable to the orebody formation and the differences in the modulii of the host rock and the orebody.

Jan 1, 1977

By T. H. Dubaniewicz, J. E. Chilton

Fiber-optic technology is progressing rapidly, including the development of fiber-optic sensors for many applications. These sensors have the advantages of high sensitivity, light weight, small size, high bandwidth, and freedom from electromagnetic influences. The U.S. Bureau of Mines is investigating the use of fiber-optic technology to monitor mine atmospheres. This report describes a methane monitor based on differential absorption of infrared light. The monitor can detect methane concentrations as low as 0.2 vol pct as far away as 2 km via fiber-optic cable. The upper range is 100 vol pct methane. Since the system requires no electrical power within the mine, it is intrinsically safe.

Jan 1, 1992

By T. W. Hunter

THE TOTAL production of energy in the United States in 1954 decreased 4.6 percent below 1953. The production of coal continued to decline, and the production of crude oil decreased for the first time since 1949. These decreases were partly offset by an increase in the production of natural gas. The total energy production of 35,365 trillion B. t. u. in 1954 was the lowest since 1950. [ ] This drop in energy production was consistent with the 1.1-percent decline in gross national product during the year-from 364.5 billion dollars in 1953 to 360.5 billion in 1954.

Jan 1, 1958

The U.S. Environmental Protection Agency (EPA) and the U.S. Congress are presently considering several approaches aimed at reducing the amount of lead in the environment and society's exposure to lead. One approach is to tax domestic primary lead production or consumption. Objective To assist the Congress and the EPA in their decisionmaking, a study was initiated by the U.S. Bureau of Mines, which assesses the minerals related implications of a tax on U.S. primary lead production and primary lead imports. This investigation analyzes the impacts of a primary lead lax on: (1) domestic primary lead production, (2) domestic lead coproduct and byproduct production (including bismuth, cadmium, germanium, indium, silver, and zinc production), (3) domestic secondary lead production, (4) lead imports, (5) domestic lead recycling activity, and (6) the U.S. lead price. Study Findings Domestic Primary Lead and Primary Lead Coproduct and Byproduct Production. A quantitative analysis based on the application of the Bureau's Supply Availability System (SAM) has been conducted to determine the impacts on domestic primary lead and primary lead coproduct and byproduct production from domestic lead source material for a range of taxes.

Jan 1, 1992

By A. Gene Collins

The Bureau of Mines conducted a research study of the geochemistry of the Smackover Formation to determine what geochemical relationships are useful in exploration for and production of oil and gas. Samples of oil, gas, brine, and rock were collected and analyzed. The oilfied brines were analyzed by methods recommended by the American Petroleum Institute and by tentative methods of the American Society for Testing and Materials. The crude oils were analyzed by Bureau of Mines methods; the gas, by Bureau of Mines methods; and the rocks, by wet-chemical, atomic absorption, and neutron activation methods. The results were correlated and interpreted, and several geochemical relationships useful in exploration and production were found. These include the type and class of brine, organic constituents in the brine, redox potential, in situ temperature and pressure of brine, degree of sulfate and carbonate saturation of brine, and halide concentrations in the brine.

Jan 1, 1974

By Murali M. Gadde, John A. Rusnak

Rock mass classification systems are extremely useful for site characterization and have been employed by the rock mechanics community for several decades. While empirical in nature, the classification systems provide a viable means to quantify the nature of rock mass, which is necessary for stability analyses. In U.S. coal mines, the Coal Mine Roof Rating (CMRR) is the most widely used classification system for several purposes, including sup-port selection, chain pillar design, assessing the stability of extended face cuts, etc. The Analysis of Roof Bolt Systems (ARBS) is an empirical method developed from the CMRR to guide selection of roof bolts as the primary support system in U.S. coal mines. In this paper, the experience of Peabody Energy in applying ARBS to sup-port design is discussed. In general, data from the Peabody mines show that ARBS predictions match well with field conditions. Peabody, however, does not use ARBS as the stand-alone methodology for support selection. Peabody uses a two-pronged approach in which the support requirement is initially estimated from the classification method, and then numerical modeling is used to select the proper reinforcement system. Such an integrated approach is necessary, as ARBS suggests only the “amount of steel” that may be used to support the roof and does not specify which type of roof bolt to use. A case study is used to demonstrate the usefulness of ARBS and Peabody’s integrated approach to support design. Also, the application of ARBS at several Peabody mines showed a very good correlation with support cost. The correlation indicated a direct relation between bolting cost and the ARBS value.

Jan 5, 2007

Aluminum alloys are used in two broad classifications: wrought and cast. Wrought alloy products, which are formed into final shape by rolling, forging, extruding. etc., contain low percentages of alloying elements; whereas cast aluminum products, which generally are not worked before use, may contain higher percentages and a somewhat different selection of alloying elements. For example, wrought aluminum alloys usually contain less than one percent silicon and cast alloys contain as much as 18 per-cent silicon. While there are good techniques available for separating aluminum alloys from mixed scrap, there are no efficient ways to separate wrought aluminum from cast aluminum. The high levels of silicon, iron) copper, and zinc from the cast alloys make wrought-cast mixtures unacceptable for wrought alloy production. Consequently, separated wrought aluminum scrap commands a premium price on the market. Since increasing amounts of mixed aluminum alloys are being recovered from automobile scrap, this separation is important for efficient recycling of these alloys. Approach The difference in thermo-mechanical properties between the two classes of aluminum alloys is used as the basis for the separation process. Casting alloys lose their ductility within a certain temperature range while wrought alloys remain ductile. As temperature increases, aluminum alloys gradually become weaker, and at a certain temperature, each alloy loses strength and ductility due to incipient melting in localized areas. For casting alloys that temperature generally lies between 520° to 560° C, but it is above 600° C for most wrought alloys. Mild crushing, therefore, in the proper temperature range will result in complete fragmentation of the casting alloys but only plastic deformation of the wrought alloys. A simple screening step then is used to separate the oversize wrought pieces from the fragmented cast alloys.

Jan 1, 1984