Search Documents

Reduce potential for steering errors during tramming of articulated vehicles, particularly when the operator is seated to the rear of the machine pivot point and is tramming in reverse. Approach Position-sensing and feedback cylinders were applied to the steering cylinders of two S&S cleanup tractors to cause the steering-control lever to match the orientation of the vehicle sections. The vehicles were tested in two working mines. How It Works A position-sensing cylinder (see Figure 1, Item A) is attached to one of the steering cylinders in the cleanup tractor steering system. As the steering cylinder piston rod is actuated by movement of the control lever, hydraulic oil flows from the position sensing cylinder to the feedbck-cylinder (B), causing the feedback-cylinder piston and rod to move. The outside end of the rod repositions the the steering-control lever until its angular position corresponds to the orientation of the vehicle sections.

Jan 1, 1978

By Robert C. Gabler

The extraction of metals from coal ash was investigated by the Bureau of Mines in an effort to produce a more environmentally acceptable waste and offset waste disposal costs with recovered metal values. The research was conducted in two steps: determination of the parameters that affect extraction of metals from coal ash and development of extraction-recovery procedures. Data obtained indicate that the major parameter affecting the extraction of metals from coal ash is the calcium content of the ash. Other parameters such as furnace type and operating temperature had much smaller effects on metal extraction. Two procedures were studied for metal extraction: an acid leach procedure for high-calcium ashes and a lime sinter-acid leach procedure for low-calcium ashes. An alumina product was recovered that, with sufficient washing, meets Hall cell specifications. The leach residues pass the EPA EP Toxicity Test and are thus nonhazardous wastes available for a variety of uses.

Jan 1, 1983

By W. H. Engelmann

The electrokinetic (zeta) potentials of a charcoal granite in an aluminum chloride (AlCl3) solution and in an oleylanunonium acetate (C18H35NH3+ -OCOCH3) solution have been correlated with the specific damping values as measured by the pendulum sclerometer. This investigation shows that the pendulum specific damping attains a minimum at the isoelectric point for the charcoal granite-aluminum chloride and charcoal granite-oleylammonium acetate systems, and thus indicates that the penetration of the diamond points is a maximum at the isoelectric point.

Jan 1, 1967

By R. D. Leitch

"INTRODUCTION The general program of the investigation of coal mine drainage which the Bureau of Mines is making includes, among its many phases and objectives, a study of the fate of the acid, content of drainage after it enters natural streams, and the effect of seasonal variations on the degree of contamination of streams. Opportunity for studying these under comparatively normal conditions and variations can readily be found, but there is only a chance opportunity for studying than under extreme conditions. The unusual drought that prevailed during the summer of 1930, however, created a condition of low water favorable to a study of one of the extremes.This report gives the results of an investigation of Bennett Branch of Sinnemahoning Creek, Pa., made under this condition.ACKNOWLEDGMENTSThis work was conducted under the direction, and with the advice, of Dr. R. R. Sayers, chief, Health and. Safety Branch, and of W. p. Yant, supervising engineer, Pittsburgh Experiment Station.DESCRIPTION OF BENNETT BRANCHBennett Branch, as shown in Figure 1, is a tributary to Sinnemahoning Creek. Its source is in Huston Township, northwestern Clearfield. County, from which it flows in a general northeasterly direction through Elk County, thenceeasterly in Cameron County to Sinnoning Creek at Driftwood. The total length is about 37 miles. There are nine towns along the stream that have an average population of about 350. There is no industrial pollution other that from coal mines and very little. domestic, pollution."

Jul 1, 1931

By C. J. Tsai, K. Olson, R. Caldow, B. Cantrell, D. Y. H. Pui

"The amount of new surface generated during fracture of coal and rock has been found to be directly proportional to the amount of energy associated with the fracture. To confirm this and study the relationship between the new surface and dust aerosol formed during fracture the U.S. Bureau of Mines has conducted experiments simulating fracture as it occurs during mining operations. In addition to fracture energy measurements, fragment size distributions were determined over a size range of 0.5 microns to 1 inch. The size measurements accounted for the mass of the original sample. Material studied was Illinois No. 6 coal, coal from the Taggart seam of Virginia, and Berea Sandstone. The experiment employed a chamber to confine sample fracture fragments and a combination of particle measuring systems. Measurement methods included aerodynamic sizing of entrained dust aerosol with optical counting and inertial impaction techniques, physical sizing of non-airborne fragments by sieving, and optical sizing of fragments using optical counting and scanning electron microscopy.Results of the size distribution measurements indicate that a single size distribution law does not adequately describe the entire fragment size distribution. A combination of two size distribution laws, such as the Rosin-Rammler and log-normal distributions, is necessary to describe this size distribution. New surface created by fracture is primarily found 1n particulate between 2 and 50 microns with a mean size of 12 microns. It was also found that the specific energy of fracture can be linearly related to the .concentration of aerosol in this size range.Only a .small fraction, between 0.02 and 0.16 pct, of the dust particles .generated during fracture become airborne. The remainder adhere to the new surface created during fracture. An entrainment fraction, defined for a given particle size is the ratio of the mass of airborne particles to that of the total particles generated in that size range. This experimental entrainment fraction is related to the Van der Waals adhesion force and the electrostatic forces operating during fracture and is used to derive empirical parameters to model these two processes."

Jan 1, 1989

By W. A. Cole

This report covers the preliminary phase of an investigation of clays, shales, and certain rocks in Wisconsin to determine the feasibility of processing lightweight aggregate in the State. The study was extended to include rotary-kiln testing of a limited number of shale samples, and to an appraisal of the Maquoketa shale resources in eastern Wisconsin. A total of 45 samples of clays, shales, and other argillaceous rocks of Wisconsin were tested. The lower Maquoketa shale is the only material found to date that offers possibilities as a source of material that can be processed in a rotary kiln for lightweight aggregate. Bedrock occurrences of the Maquoketa shale are found in the eastern and southwestern parts of the State. The populous southeastern region of Wisconsin presents a large potential marketing area for lightweight aggregate. For this reason special study was directed to the Maquoketa shale in the eastern district.

Jan 1, 1961

By T. M. Barczak

This report describes Bureau of Mines research to develop methods to evaluate loading on longwall roof supports to permit better design and more efficient utilization of these structures in compliance with the geological conditions in which they are employed. The resultant vertical and horizontal force acting on the canopy of a shield can be determined, either from a statically determinate solution assuming rigid-body mechanics and elimination of certain unknowns, or from an elastic solu-tion by analysis of the load-displacement relationship of the shield structure. A two-dimensional rigid-body model is presented that determines resultant shield forces by measurement of leg, canopy capsule, and lemniscate link forces. An elastic solution is presented, in the form of an elastic stiffness model with two degrees of freedom, which describes the load-displacement relationship from the stiffness of the shield structure as determined in the Bureau's Mine Roof Simulator (MRS). The ability of both models to determine resultant forces acting on the shield canopy are evaluated from full-scale tests in the MRS. More advanced numerical models are also discussed as part of the Bureau's continuing effort in the evaluation of roof support structures.

Jan 1, 1987

By Charles L. Kimbell

In broadest overview, UN global industrial production indicators released and shown in table 2 suggest that the extractive sector of the world's mineral industry in aggregate registered a very slight upturn in 1991 relative to its 1990 performance. It also shows a continued rebound in the industry from the recessionary period of the mid-to late-1980's. These same indicators as calculated in late 1991, however, reflected a very minor downturn in extractive mineral industry operations between 1989 and 1990. This latter downturn represented a notable revision from the data reported in the immediate previous edition of this chapter, which suggested a tiny upturn. The apparent slight 1991 upturn in extractive sector industrial output generally was not mirrored in the performance of the processing sectors of the global mineral industry. Although the aggregate index for the chemicals, petroleum, coal, and rubber products manufacturers (see table 3) showed a notable gain in 1991, similar indices for nonmetallic mineral products and for base metals registered declines between 1990 and 1991. Examination of regional performance indices shows that the difficulties experienced in 1990 in maintaining output levels within the countries that formerly constituted the CMEA were reinforced by trends toward reduced gains in output levels, if not actual reductions in output, in several other areas. Generally speaking, the traditional developed market economy countries recorded downswings in overall industrial activity in 1991, particularly after midyear, whereas developing market economy countries logged gains. The developed market economy country downturns, however, were not nearly as significant as were the downturns recorded for the former centrally planned economy states - those that before 1992 were either constituent Republics within the U.S.S.R. or the latter's CMEA partners.

Jan 1, 1993

By J. Dean Warner

In 1984, as part of a project to evaluate Alaskan occurrences of certain critical and strategic minerals, the Bureau of Mines investigated a columbium-bearing regolith on upper Idaho Gulch, near Tofty, AK. The regolith is derived from weathering of a dolomitic marble and consists mostly of iron oxide minerals with accessory apatite, zircon, xenotime, rutile, monazite, and the columbium minerals aeschynite, columbite, and ilmenorutile. Two regolith lenses contain 340,000 lb of columbium resources at an average grade of 0.07 pct. Calculated composite concentrates from two regolith samples (approximately 200 lb each) contained 53 and 57 pct of the columbium at grades of 0.97 and 0.86 pct, respectively. In each case the grade could be improved to 1.1 pct Cb with a sacrifice of 9-pct recovery. The regolith's mineralogy, trace-element geochemistry, and similarity to descriptions of other columbium-enriched regoliths suggest that the underlying marble may be a carbonatite. The lack of associated alkalic igneous rocks and the stratiform nature of the regolith, however, may be interpreted as evidence for sedimentary origin of the marble. The marble and regolith are a lode source for some of the minerals in the Idaho Gulch placer deposit.

Jan 1, 1986

By Jack D. Ramsdell

Electrorefined, magnesium-reduced, and sodium-reduced titanium samples were evaluated for recrystallization behavior, effect of cold rolling on tensile properties, and bend ductility. Curves were determined for the softening of 2.5 to 80 percent reduced cold-rolled metal that was annealed over a temperature range of 300° to 800° C. Upon annealing, coarsening of the grains was found to occur for reductions in thickness of less than 20 percent in titanium made by all three processes. The presence of metallic impurities greatly inhibits coarsening for reductions in thickness below 20 percent, but for reductions in excess of 20 percent grain size is essentially constant at each annealing temperature. The three grades of titanium did not harden excessively from cold rolling; both tensile and bend ductility were good for reduction in thickness up to 80 percent. Upon annealing, softening occurs between 400° and 600° C., and, based on microstructure and property studies, full annealing is accomplished after 30 minutes at 700° C. for the magnesium-reduced and electrorefined titanium and at 800° C. for the sodium-reduced titanium.

Jan 1, 1960

Improve the safety of salt mine workers by providing a means for quickly identifying areas within the mine that?s how an increased potential for gas and salt outbursts. Approach Outbursts occur in salt mines when a high-pressure pocket of gas is intercepted during the mining process, resulting in a sudden and sometimes catastrophic expulsion of gas and salt. In one case, the amount of gas released through such an event caused an explosion that resulted in five fatalities. The U.S. Bureau of Mines has designed and developed a gas outburst prediction system that can quickly determine the potential instability of areas within rock salt mines. The determination is based on noise measurements obtained from samples of the salt as they are dissolved in water. This system improves upon technology currently available because it provides information in only a few minutes instead of in several days. In addition, present prediction systems are not only time consuming, but expensive because they require laboratory conditions and highly trained personnel to operate them and determine results.

Jan 1, 1989

By J. E. Pahlman

As part of its goal to minimize the requirements for mineral commodities through conservation and substitution, the Bureau of Mines is conducting research to determine the resistance of alumina refractories to corrosion by alkali-containing slags that could result from burning of the abundant Western lignites in metallurgical operations. Static corrosion tests were performed at 1,000° to 1,350° C and dynamic tests were performed at 1,400° to 1,600° C to investigate the stability of refractory specimens in slag environments. In general, the degree of refractory attack increased with decreasing alumina content in the refractory and with increasing alkali content of the lignite ash. The parabolic kinetics observed in static tests suggested that a reaction product layer is formed through which ionic diffusion must occur to sustain the reaction with the refractory material. The linear kinetics observed in dynamic tests in high-viscosity slags indicated a shearing of the reaction product layer by viscous slags. The observed lesser attack of refractories by low-viscosity slags can be explained on this basis. Two 99-percent-alumina refractories and two 90-percent-alumina refractories formed an expanded protective layer with the more viscous slags but not with the less viscous slags. Corrosion of 90-percent-alumina refractories increased exponentially with temperature. In refractories with the same nominal alumina content, those that contain a combination of a-Al203 and mullite (3A1203?2Si02) have better corrosion resistance than those containing a combination of a-Al203, cristobalite (Si02 mineral), and mullite. In alkali environments (1,300 to 1,400° C), 90-to 99-percent-alumina refractories are recommended for use as furnace linings.

Jan 1, 1980

The initial results from the magnetic sludge factorial experiment are summarized in Table 2. For ease in interpretation, the four separate variables are identified with the high and low level of each variable being represented by + and - signs, respectively. Several important relationships are evident from an inspection of the data in Table 2. For example, magnetic sludges were obtained only during the high temperature tests. Secondly, with the exception of the last three tests, there is an apparent correlation between settled sludge volume (or sludge settling rate) and pH. Data on residual dissolved Fee+ indicate that precipitation of iron is not complete at pH 8 and room temperature (Tests l, 3, 5, and 7). Although this should not have any confounding effect on the interpretation of the results, it is an important observation and an aspect of the overall conceptual process that should be considered carefully during any future developmental work. The data in Table 2 were employed more fully in the calculation of main effects and variable interactions for each of the three responses. For this purpose, a codified design and calculation matrix, shown in Table 3, was used. The derivation of this matrix is described by Davies.(9) The positive or negative signs for variable interactions are obtained simply by algebraic multiplication of the signs for each single variable involved in the interaction. Main effects and interactions are calculated by multiplying the response values (Table 2) by the corresponding effect elements (Table 3), summing the results, and dividing by 8. The resulting value for single variables is also sometimes designated as an average effect, since (for tyro levels of the variable only) it is simply the difference between the average response of all trials carried out at the first level of the variable (factor) and that of all trials at the second level. If the effect of one variable changes at different levels of another variable, the two variables are said to interact. The relative importance of the variable or variables in question is reflected by the absolute magnitude of the calculated main effect or interaction. First-order (two variable) interactions are usually easy to interpret in terms of the physical behavior of the system. Second- and higher-order interactions are often less readily understood, and are often of minor significance in any case. The main effects and interactions derived from the present study in the manner described above are listed in Table 4. It should be noted that

Jan 1, 1971

By Tobias W. Goodman

The U.S. Bureau of Mines used a contact drilling strategy with short-collared assemblies in order to rotary drill long horizontal methane drainage holes in the Beckley Coalbed near Glen Daniel, WV. By decreasing the thrust, and increasing the rotation of the drill bit when in contact with the roof and floor rock, assemblies with 1-ft (0.3-m), 10-ft (3- m), and 144 (43-m) long collars were made in deflect and stay in the coalbed. Successful application of this procedure resulted in holes drilled full length in coal with the original assembly including bit. The test assemblies deflected away from the original bearings of the holes during drilling and arced. Four holes were drilled to depths ranging from 478 ft (145.7 m) before the strategy was developed, to 4,034 ft (1,230 m) when the strategy was applied. Total length of the holes in coal was 8,590 ft (2,618 m). After 577 days the total methane captured by the holes was 221,600,000 ft? (6,276,000 m3). The methane flow rate peaked at 805,000 ft3/d (22,798 m3/d), then decreased to stabilize at 670,000 ft?/d (18,974 m3/d) after 6 months.

Jan 1, 1989

By Nicholas G. Theofilos

Ecuador's real gross domestic product (GDP) increased 6% in 1976 despite persistent shortages of electrical power and essential fuels, which caused factory slow-downs and shutdowns. Petroleum export earnings, which made up more than 50% of total export value in 19716, totaled $565 million, a 9% increase over those of 1975. A new 60,000-barrel-per-day oil refinery at Esmeraldas was scheduled to go on- stream in mid- 1 97 7, operating entirely on Ecuadorean crude. Corpración Estatal Petró1era Ecualtoriana (CEPE) started construction of a 600-kilometer network of product pipelines which was scheduled to be completed in 1977 to coincide with the completion of the refinery.

Jan 1, 1980

Publicize the valuable information resources covering research conducted by the U.S. Bureau of Mines (USBM) and other federal laboratories that may be of interest to USBM customers. Access to this information is important for promoting further research and in transferring the technology to the end user. USBM Information Resources The USBM serves as the Nation's premier agency for mining- and minerals-related research. In sharing the benefits of this research with American industry and the American people, the USBM supports information systems outlining this vast array of technical knowledge. The USBM is dedicated to making its technology readily available and will continue to expand its electronic communications capabilities. The following resources provide instant access to USBM information. U.S. Bureau of Mines Bulletin Board. The Bulletin Board is a free service accessed by computer modem. All that you need are a computer, a modem, and communications software. The telephone number for the Bulletin Board is 202-501-0373; for information on using the system call 202-501-0406. Use X-modem protocol set to 1200, 2400, or 9600 baud, 8 data bits, and 1 stop bit (8,N,1). The information on the system can be viewed or downloaded. This service includes the following: announcements on Bulletin Board and other USBM activities; mineral news, features, and press releases from the Bureau's Office of Public Information; a list of recent publications and articles by USBM authors; mineral commodity data and Mineral Industry Survey reports; USBM Technology News, concise factsheets announcing milestones in USBM research and technology; a current list of computer products available from the USBM and the National Technical Information Service (NTIS); and a listing of cooperative research opportunities with the USBM.

Jan 1, 1995

By A. N. Styler

As part of its water-jet assisted rock cutting research, the Bureau of Mines has initiated a study into the mechanism of rock fragmentation by water-jet-assisted mechanical tools. The objective of this research is to increase coal extraction efficiency by seeking an improved understanding of the synergistic relationship between mechanical cutters and water jets, enabling the design of more effective cutterheads. Rock chips collected during laboratory traverse speed jet-assisted cutting tests were analyzed with respect to the size distribution of the chips and the forces measured during cutting. As the water-jet pressure was increased, the size distribution of the product became coarser with V-face type cutting tools producing less fine material than conical cutting tools. Fracture mechanics theory accounted for less than 10 pet of the energy consumed during fragmentation of the rock. The energy consumed by processes other than rock breakage decreased with the use of water jets and increasing advance rate.

Jan 1, 1987

By R. V. Ramani, A. S. C. Owili-eger

The rapid depletion of shallower coal reserves dictate that mining in the future will be deeper and more complex with more difficult natural conditions. Consequently, an increase in methane emission is expected. It is becoming evident that more accurate predictions and better planning are necessary to design efficient methane drainage systems. This objective can be achieved by the utilization of the knowledge of the physics of gas flow through coal seams and rock strata and by the application of digital computers in the solution of methane flow problems. Although the methane emission models described here have not been adequately applied to existing field operations, good agreement between actual field measurements reported in literature and the simulation results indicates the potential of these models for initial flow quantity approximations and ventilation planning. This report has, therefore, introduced to the mine operator yet another application of computers as a planning tool. AREAS FOR FURTHER RESEARCH The study reported here is by no means complete. Extensive research efforts should be directed to the following areas: (a) Better understanding of the physics of gas flow through porous media which exhibit fracture permeability. (b) Determination of field parameters which control gas migration. (c) Investigation of the effects of the rate of penetration on the emission rate and fracture propagation.

Jan 1, 1974

By V. A. Marple, K. L. Rubow

"In our laboratory several impactors have been developed in the past which have penetration characteristics that approximate that of the ACGIH or the British MRC respirable curves. In these impactors the large nonrespirable particles are collected on an impaction plate of a multiple round nozzle stage where the nozzles are of different diameters. The principle for designing a respirable cut impactor is quite simple in that the respirable curve is divided into two or more segments and the nozzles are designed with the correct diameters and number of nozzles to have collection characteristics with 50% cutpoints at the center of each segment. The particles not collected on the impaction plates are then collected upon a filter. These particles represent the respirable fraction of the aerosol. Therefore the respirable curve is approximated in a stepwise fashion with the approximation becoming better as the respirable curve is divided up into increasing numbers of segments. It has generally been felt that three segments is satisfactory for most cases.A new version of the respirable impactor has recently been developed in our laboratory. This impactor approximates the ACGIH respirable curve in three steps at a flow rate of 30 liters per minute. However, unlike previous models where all of the particles larger than the three cut points designated by the three steps are collected upon one impaction plate, a separate impaction plate is now used for each of the three cut sizes. To approximate the respirable curve in three steps, the cut sizes must be 2.2, 3.5 and 5.8 microns diameter. Therefore, on each of these stages the particles collected will be the mass of particles that are larger than these three cut sizes. By determining the mass of particles collected on each of these three stages plus that on the after filter using Gravimetric techniques, some information can be obtained on the size distribution of the aerosol being sampled. Furthermore, the impaction plates of the three stages are rotated and the nozzles are placed in such a position such that a uniform deposit is obtained on each of the impaction plates. Therefore, the deposits collected are suitable for X-ray fluorescence analysis or other types of analysis where a uniform deposit is required."

Jan 1, 1988

By Roy Greenfield

During the detection phase, several procedures can be used to improve the signal-to-noise ratio (SIN) . • Subarrays of up to 10 seismometers should be used. The apparent failure to obtain improvement in SIN in the Westinghouse subarrav work is probably due to excessive noise in the electronics. The spacings needed for sensors in the subarray must still be established. • The sensors should be buried. Even burial to a few feet will probably give appreciable reduction of noise. A deeper burial will probably further reduce the noise; and, if the seismometers can be put below the weathered layer, the signal level will probably be increased. The reduction in noise by burial will be especially effective during high noise periods due to wind or rain. • Before attempting detection, the waveforms should be bandpass filtered. The bandpass should go from 25 Hz to an upper frequency of 100 to 200 Hz. Further measurements with a low noise system must be done before the signal-to-noise ratio can be determined for the 100 to 200 Hz range. Any narrow band noise should be removed by notch filters. • If noise levels differ among seismometers of a subarray, weights inversely proportional to the noise power should be applied to the seismometers. • Automatic methods of screening data for possible signal arrivals should be developed, but the final determination that the signal on a subarray output appears to be from a miner should be made by an analyst. Detection of "signal" on several subarrays should be required for positive identification. In the location phase, after detection: • If repeated signals are received, they should be coherently added (stacked) to give as good a SIN as possible for use in determining signal arrival times, to be used in location computations. The miner should, if possible, repeat the signal 25 to 50 times.

Jan 1, 1974