Search Documents

By J. H. Heginbotham

As part of the total metallurgical system to recover metals from secondary resources, the Bureau of Mines conducted froth flotation research, using cationic reagents to recover glass from urban refuse. Batch flotation tests showed that high-quality cullet can be obtained from glass-rich aggregates derived from municipal incinerator residues and unburned refuse. This was confirmed by pilot plant operations treating 350 pounds of flotation feed per hour. Aggregates containing 85 to 90 percent glass were wet-ground to minus 20 mesh, deslimed in two stages, and fed to flotation cells. The glass was selectively floated using an amine collector, usually in an amount under 0.2 pound per ton of solids in the feed. The glass concentrates from the rougher cells were cleaned by refloating two or three times. Over 90 percent of the glass in the deslimed feed was recovered in the cleaned concentrates.

Jan 1, 1978

By R. V. Ramani, V. T. Burgos, J. A. McClay

The data for Test I1 describes an underground bituminous coal mine operating in a 72 inch seam, with an estimated production rate of 4,257,000 tons per year. The system includes 15 continuous mining sections, conveyor belt haulage, and a rail network for supply and personnel transportation. The following section includes the input data sequence, annual cost report, and cash flow analysis "report for this data set.

Jan 1, 1975

By Webster S. Anderson

Two series of tests were run with planer model 'BB": one at the Arickaree mine of the San Francisco Chemical Co., Rich County, Utah, and one at the Roslyn No. 9 mine of the Northern Pacific Railway Co., Roslyn, Wash. The tests at the Arickaree mine were started on June 25, 1958, and continued until September 30, 1958. Prior to these tests, an electrically activated remote-control system was installed, and other modifications were made on the planer. The tests showed that the planer in general and the remote-control system worked very well; however, the various cutting tools used would not consistently penetrate and cut the phosphate rock. This indicated that the cutterhead design had to be changed before the planer would operate efficiently in phosphate beds similar to the "A" bed in the Arickaree mine.

Jan 1, 1962

By E. O. Binyon

The Blue Metal corundum-andalusite deposit, in the Buckskin Mining district, Douglas County, Nev., was explored by the Bureau of Mines in 1945. The results of that work were presented in Report of Investigations 3895, exploration of the Blue Metal Corundum Property, Douglas County, Nev. published in August 1946. That report also describes the property in detail, giving location, ownership, history, geology, and data on beneficiation tests. Further exploration was carried on in April and Way 1947, the results of which are presented in this report. The work consisted of 175 feet of drift and crosscut, bringing the total to 398 feet of underground working, as shown in figures 1 and 2. The 23-foot drift, which was the last work of the initial project, was extended 99 feet northward along the shear zone, and three crosscuts, spaced at approximately equal intervals along the drift, were driven to country rock on the hanging and foot walls of the zone.

Jan 1, 1948

By B. W. Jong

The U.S. Bureau of Mines investigated anhydrous chlorination and caustic-acid leaching processes to recover Ni, Co, Mo, and W from waste hydroprocessing catalysts. In batch laboratory-scale equipment, the chlorination process extracted 61 to 99 pet of the metals. Final recovery was 65 to 99 pct. The caustic-acid leaching process extracted 81 to 98 pct of the metals. Final recovery was 36 to 99 pct. Chlorination processing included roasting, chlorination, hydrolysis of metal chlorides for recovering Mo or W, water leaching of Ni or Co from the spent charge, purification, and solvent extraction or precipitation of Ni or Co from the purified solutions. Caustic-acid leach processing included NaOH leaching, solvent extraction of Mo or W from the NaOH leach liquor, H2S04 leaching of the NaOH leach residue, purification, and solvent extraction or precipitation of Ni or Co from the purified solution. The estimated fixed capital cost for a commercial-scale plant processing 39,000 Ibid of waste Ni-Mo-AI catalyst was $8 million for the chlorination process and $9.6 million for the caustic-acid leaching process. The estimated operating cost was about $0.20 and $0.40 per pound of the waste catalyst, respectively, for the two processes.

Jan 1, 1989

By James P. Ulery, Jon C. Volkwein

The U.S. Bureau of Mines investigated a method of using inert gas to prevent the formation of explosive gas mixtures in auger highwall mining of coal. A combination of gasoline and diesel engine exhaust gases was introduced into the auger drill hole using a short section of pipe located at the collar. Gas samples were taken and analyzed on-site with infrared detectors for oxygen, carbon dioxide, methane, and carbon monoxide. Evacuated bottle samples were also taken and analyzed by gas chromatography in the laboratory. These gas results were analyzed for explosibility. Coal samples from various depths were used to obtain the gas content of the coal using the modified direct method. Personal expo- sure to carbon monoxide was also monitored. The highest methane level observed was 9.55%. The levels of inert gas (carbon dioxide and nitrogen) were sufficiently high to prevent any ignition of the methane. Results showed that for all conditions during mining, gas concentrations were nonexplosive. The gas content of the coal was about 0.30 cm3/g. The maximum personal time-weighted average sample for carbon monoxide was 20 ppm. This system provides a safe, inexpensive, simple method for pre- venting explosions during auger mining.

Jan 1, 1993

By Arthur M. Hartstein

The Bureau of Mines, through contract with Ultrasystems, Inc., obtained data on the oxidative degradative behavior of a number of materials used in coal mines. Tests were performed using a stagnation burner arrangement. Materials examined included those used in typical coal mining operations such as (1) polyvinyl chloride-containing materials. (2) neoprene compositions, (3) rigid foams (urethanes/isocyanates), (4) miscellaneous materials (including jute, fiber glass, and polyethylene), (5) coal, (6) fluids (phosphate esters, organic esters, oil-water emulsions), and (7) composites. The composite comprised a mixture of a phosphate ester fluid with (1) coal, (2) a representative polyvinyl chloride sample, or (3) a neoprene-type composition. A number of decomposition products are identified that could represent a potential health hazard to miners including HC1, CO, SO2 and H2S, if they were generated to exceed toxic levels.

Jan 1, 1974

By James D. Sisler

Location and Age The main bituminous coal field of Pennsylvania lies in approximately twenty counties west of the mountain area which extends in a northeast southwest direction through the central part of the Commonwealth. The coal fields lie in a dissected peneplain, still in the youthful stage of erosion There are numerous V shaped valleys in the bituminous fields and the tributaries of the larger streams have rather steep gradients The main streams flow in rather narrow valleys with comparatively small flood plains. The coal beds of Pennsylvania are of Carboniferous age, and are confined to two systems, the Permain and the Pennsylvanian The latter system is divided into an upper or Pittsburgh series and a lower of Pottsville series The Peimain system is divided into an upper and lower series The Pottsville series of the Pennsylvanian is represented in western Pennsylvania by the Upper Pottsville only The upper or Pittsburgh series of the Pennsylvanian is represented by the Monongahela, Couemaugh, and Allegheny groups Geologic Structure. The rocks of the bituminous coal fields are folded into many anti clines and synclines extending in a general northeast direction across the western part of Pennsylvania The intensity of this folding in creases toward the mountain region West of Chestnut Ridge, which is in Fayette, Westmoreland, and Indiana counties, the folding is minor, and the coal beds have low dips East of Chestnut Ridge, v here folding is stronger, the basins are wider and the coal beds rise steeply on the flanks of the anticlines Geology. The bituminous coals of Pennsylvania are associated with shale, sandstone, clay, and limestone Each group has different proportions of these deposits, and the proportions vary at different localities within the same group.

Jan 1, 1928

By Oliver C. Ralston

OUTSTANDING TRENDS of the year included the following: 1. Concentration and beneficiation of iron ores to provide improved blast-furnace feed and extend ore reserves. 2. Successful development of pelletizing and sintering procedures for fine iron ores. 3. The realization that cyclone separation could replace existing classifiers in many grinding circuits. 4. The rapidly blossoming metallurgy of ultrapure silicon and improvements in zone melting. 5. The rapid increase in the use of liquid-liquid extraction and ion exchange in hydrometallurgy. 6. The industrial application of vacuum melting on the 100-ton scale. 7. The hope for developing a columbium (noibium) base alloy for high-temperature use. The technologic advancement in metallurgy that had the greatest effect on the American economy was the beneficiation of iron ores to give improved feed for blast furnaces and indirectly extend our ore reserves. This was not a sudden development but rather culmination of a decade of intensive effort.

Jan 1, 1958

By F. E. Brantley

Optimum autoclaving conditions were determined for separation of iron and manganese values from pregnant leach liquor produced in extracting manganese from low-grade umber are. The umber was leached with a synthetic anolyte similar to a recycle solution, used in manganese electrolysis cell operations, that had been renewed with ferrous sulfate and sulfuric acid. The equipment used and results obtained are presented for the several conditions employed. The kinetics of the separation were studied. Rate equations were derived for the formation of solid ammonium-manganese sulfate, (NH4)2 Mn2 (S04)3.

Jan 1, 1968

By H. P. LeVan

The Bureau of Mines has developed a technically feasible continuous single-stage leaching and thickening system for extracting manganese from umber by a sulfuric acid-ferrous sulfate process; the cocurrent leaching and thickening system proved simpler to operate and control than the countercurrent leaching and thickening system developed earlier" Related tests investigated the use of a centrifuge to replace thickeners for separating the product liquor from are residues and compared several chemical agents for removing iron from the pregnant manganese leach solutions. Results of Some exploratory autoclaving tests are also given.

Jan 1, 1972

By Sean Gallagher, Thomas G. Bobick, Diane M. Doyle-Coombs, Richard L. Unger

The U.S. Bureau of Mines has developed an in-house facility to evaluate selected effects of whole-body vibration (WBV) levels experienced by underground mobile equipment operators, Vertical vibration data were collected from a coal haulage vehicle via a uniaxial accelerometer attached to the machine frame under the operator&apos;s seat. Data were analyzed and processed so a computer-controlled platform could approximate the vibration signals. Eight men (35.5 yr 2 6.5 SD) participated in a pilot study to evaluate the effects of shock and kBV on heart rate (HR), blood pressure (BP), and subjective discomfort. Subjects were exposed to vibration for 30-min periods while seated in a typical seat (backrest angle at 90° or 130°) &apos;that was plain steel or modified with 2 in foam padding. Subjects repeated the same protocol on a separate day, without the vibration. Results indicated the vibration significantly increased the HR (Q< 0.01), systolic BP, mean BP, the number of times subjects reported discomfort, and overall subjective discomfort rating (pc 0.85). When seated in the steel seat, the overall discomfort rating (E< 0,081) ad the number of times discomfort was reported (p< 0.05) increased significantly. Seatback angle had no significant effect on any of the dependent measures.

By S. J. Hussey

The Bureau of Mines investigated the applicability of carbon-in-pulp pro-cess for recovering silver from low-grade ores. The reasons for the research were (1) to illustrate a practical procedure for the process design of carbon-in-pulp adsorption circuits using leach slurries and simple equipment; and (2) to illustrate how equations of adsorption theory relating rate data and equilibrium adsorption curves can be helpful in process design. Carbon-in-pulp silver adsorption tests were made on Banner, Idaho; mine-run ore samples with silver contents ranging from 2.0 to 8.5 oz/ton and variations in cyanide leach extraction from 48 to 93 pet. The lower recoveries were attributed to the presence of complex silver sulfide minerals. Carbon-in-pulp batch adsorption tests provided rate data for the estimation of a silver equilibrium adsorption curve. Process design procedures in which the rate data were related to an equilibrium adsorption curvey by equations of adsorption theory were used to plan a four-stage pilot plant cascade. The pilot plant was successfully operated for 45 hr of countercurrent flow, producing a carbon product containing a mean silver loading of 571 oz/ton from a pregnant solution of 1.7 oz/ton of silver. Virtually all of the dissolved silver was recovered on the carbon.

Jan 1, 1978

By Fun-Den Wang

Finite-element structural analyses were performed to determine the stress distribution and displacements around a single rectangular coal mine opening in a multilayered rock system. The effects of changes in mechanical properties of roof and coal layers, roof layer and mine opening geometry, horizontal-to-vertical load ratio, and structural geologic features on the stress distribution about the opening were studied. Variability in the stiffness and relative thickness of the immediate roof layers can produce a considerable difference in the stress distribution about the opening as compared with that of a homogeneous material. Changes in opening width and horizontal-to-vertical load ratio have different effects on the stress distribution about the opening depending on the composition of the roof layers. In general, where a stiff layer exists in the roof at the surface of the opening, the stresses are higher in the roof and ribs around the opening. Horizontal changes in facies in the roof layers produced by structural geologic features can also greatly alter the stress distribution about the opening compared with the simple layered cases.

Jan 1, 1974

By D. J. Bauer

Solvent extraction separation of light group rare-earth elements in a quaternary ammonium compound-chelating agent system was demonstrated in single-stage studies, Typical separation factor values obtained were 93 for lanthanum-praseodymium, 5.4 for praseodymium-neodymium, and 11.6 for neodymium-samarium. These values are significantly higher than those obtained using organophosphate extractants. Further studies in a 20-stage countercurrent mixer-settler resulted in the production of 99 percent lanthanum (oxide basis) at 96-percent recovery. Subsequently, 88 percent of the neodymium with a purity of 92 percent was recovered in the raffinate.

Jan 1, 1971

By Irven A. Jacobson

The thermal reactions of l-methylindole were studied in the temperature range of 525° to 627° C in a flow reactor. The major products consisted of 2-methylindole, 3-methylindole, indole, quinoline, hydrogen, and methane. 2-Methylindole is formed from 1-methylindole by an irreversible isomerization reaction. The 2-methylindole isomerizes in a reversible manner to 3-methyl-indole, the equilibrium favoring the 3-methyl isomer. Indole is formed directly from 1-methylindole. Quinoline is formed from l-methylindole, 2-methylindole, and 3-methylindole.

Jan 1, 1971

By C. C. Shale

A semicommercia1, high-temperature electrostatic precipitator and adjunct equipment are described, and operating characteristics at 1,470° F and 80 psig are presented for both positive and negative polarity. Removal efficiency for negative corona waS about 91 to 96 percent while that for positive corona was only about 75 to 77 percent. Results are compared with those from bench-scale investigations, and equipment limitations are discussed. Theoretical aspects of the precipitation process are related to the operating characteristics.

Jan 1, 1969

To improve mining safety and efficiency by providing a practical way of detecting faults and channel sands that disturb coal seams. Approach A seismic system using a shallow blasthole has been developed and tested. How It Works A small shock is caused in a shallow hole, sending seismic waves through the ground. These waves are reflected from the top of the coal seam, acid are detected by a line of geophones on the earth&apos;s surface. Dampening of the seismic signals by channel sands and other discontinuities in the seam is detected and recorded. See Figure 1. The seismic shock wave can be produced by exploding small charges, dropping a weight, firing a gas gun, or actuating a vibrator. Depending on the soil cover, the shock is usually generated in shallow vertical holes about 10 feet deep. Hole depth depends on the soil mantle thickness because it is preferable that the seismic shock originate below that layer.

Jan 1, 1976

By E. Morrice

Techniques developed by the Bureau of Mines for the preparation of high-purity rare-earth metals and their alloys by electrolysis of the oxides in fluoride media are summarized. Cerium, lanthanum, neodymium, praseodymium, dysprosium, gadolinium, and yttrium metals, the mixture didymium, and specific alloys of these metals and samarium with iron, nickel, chromium, and cobalt were prepared. Individual metals were electrodeposited in the liquid state on tungsten or molybdenum cathodes. Alloys were prepared by electrodepositing the rare-earth metal on a consumable cathode, at a temperature above the melting point of the eutectic formed between the rare-earth element and the cathode material. Cells were designed for electrowinning metal products in gram and pound quantities, and methods for continuous electrowinning of cerium and lanthanum were developed.

Jan 1, 1968

By W. C. Smith

The U.S. Bureau of Mines examined previous research on rib stability in an effort to develop a practical approach to understanding, characterizing, and controlling weak rib conditions in underground coal mines. Because success in stabilizing ribs depends on a basic knowledge of how weak ribs behave, the report reviews the mechanics of rib failure and the relationship of coal mine geology and pillar constraint to rib instability. Strategies for choosing an effective method of rib support are considered, and various rib support methods are discussed. Finally, the report documents techniques for monitoring ribs and use of models to assess rib stability; such monitoring and modeling can also help determine the most effective method for roof support.

Jan 1, 1992