Search Documents

By A. L. Service

Idaho has nearly 6 billion tons of potential sources of phosphorite, 10 to 31 percent P2O5' above and within 100 feet below entry level, the largest potential of any State in the United States. In 1963 Idaho ranked third after Florida and Tennessee in total mine and marketable production of phosphate rock; Montana ranked fourth. This report describes phosphate deposits, mines, and prospects in 10 districts covering most of the Idaho phosphate field. All mine production of phosphate rock in Idaho comes from surface mines and is processed to phosphate fertilizers, phosphoric acid, and elemental phosphorus. Producing districts are Fort Hall (Gay mine), Trail Creek (Conda and Ballard mines), and Crow Creek (Georgetown Canyon mine). FMC Corp. and J. R. Simplot Co. at Pocatello have the largest elemental phosphorus and fertilizer production facilities, respectively, in the State, followed by Monsanto Co. and El Paso Natural Gas Products Co. (formerly Central Farmers Fertilizer Co.). The only other major phosphate processing plant in the State is the phosphoric acid and phosphate fertilizer complex at Kellogg operated by the Bunker Hill Co. In 1963 a plant was constructed and put on line at Monsanto, Idaho, to recover vanadium from ferrophosphorus produced by electric furnace operations in the area. El Paso Natural Gas Products Co. completed construction of a fertilizer and phosphoric acid plant near Conda in 1965. There is a small fertilizer plant producing phosphate fertilizers for local consumption in Soda Springs.

Jan 1, 1966

By J. Wade Watkins

One potential peaceful application of nuclear explosives is stimulating the production of liquid or gaseous hydrocarbons from essentially nonproductive deposits of petroleum, natural gas, oil shale, and tar sands. Within the United States the appreciable difference between producible proved reserves and ultimate reserves and resources of hydrocarbon deposits is of such magnitude that much petroleum, natural gas, shale oil, and bitumen will not be produced unless significant technological progress is made in production techniques. The shattering effect of contained nuclear explosives and, to a lesser extent, the heat produced, have been considered as stimulative forces when the thickness, depth, and nature of such deposits permit considering the use of nuclear devices. Mechanical production problems would be less in an oil or gas reservoir than in an oil-shale or tar-sands deposit. Also, tar-sands resources in the United States may not be adequate to warrant serious consideration of applying nuclear-explosives stimulation. Gas reservoirs should present the least-radioactive-contamination problem. The technical feasibility of using nuclear explosives cannot be evaluated fully at present. Additional information is needed on the effects of pressure, heat, and radioactivity on the solids and fluids of hydrocarbon deposits, the nature and extent of induced fractures in different rock media, and the possibility of isolating and confining or removing radioactive contaminants. Final technical feasibility can only be determined by a field test. If technical feasibility is established, economic feasibility will depend upon the comparative cost of producing hydrocarbons by nuclear explosives and by conventional means. It is probable that an economic comparison would favor nuclear stimulation only where devices of relatively high yield could be used practicably and safely.

Jan 1, 1964

By K. P. Wang

Mining and metallurgy have had a long history in China, and resources there have always been considered promising. Under the People's Republic of China (PRC), a remarkable industrial renaissance is underway that should further gain momentum in the years ahead. Rapid development of minerals have not only brought the PRC prominence in industrialization, but also in world affairs. Chinese mineral developments, especially petroleum, have been increasingly in the news. Oil and gas may have great potential, but a very large coal industry is already in existence. The steel industry ranks fifth or sixth in the world. The PRC is also prominent in fertilizer, cement, and salt production. The export metals are well known. Also, the country is buying heavily in nonferrous base metals. The need to know and the intense interest in the subject have prompted this study. The world significance of Chinese minerals is pointed out. The history of growth and PRC's mineral supply position are reviewed. Evaluations are made of policy considerations and regional and technical factors affecting mineral development. PRC's mineral trade and efforts to obtain equipment, supplies, and know-how are assessed. Specific reviews are made of major mineral sectors, including coal and power, oil and gas, iron and steel, nonferrous metals, industrial minerals, and fertilizers and chemicals. The overall outlook is summarized.

Jan 1, 1975

By Andrew B. Cecala

The U.S. Bureau of Mines has designed and evaluated total mill ventilation systems at two different mineral processing operations. Both systems have proven very effective at reducing respirable dust levels throughout the mill in a cost-effective manner. A 25,500-cfm system installed at a clay processing mill provided approximately 10 air changes per hour. This system reduced respirable dust concentrations by approximately 40 pct throughout the mill building. The second evaluation was performed at a silica sand operation. Tests were performed with 50,000 and 100,000 cfm of ventilation to the mill building, corresponding to 17 and 34 air changes per hour. Average mill-wide respirable dust reductions were 36 and 64 pct, respectively. Not only did these systems reduce respirable dust concentrations and increase visibility throughout the mills, they were also easy to install and required minimal maintenance. A total mill ventilation system provides a general purging of the mill air; the system should be viewed as a supplemental technique to assist other dust control systems in operation.

Jan 1, 2010

By Walter E. Lewis

This circular presents the method of making tests and apparent results of comparing performance of tungsten carbide insert bits and steel detachable bits by the Cleveland-Cliffs Iron Co. at the company's mines on the Marquette iron range of Michigan. The mines are at Ishpeming and Negaunee, Mich., and include the Cliffs Chaft, Mather "A", Cambria-Jackson, and Mather "B". There are four general characteristic types of high-grade iron ore on the Marquette range. B. H. Boyum2/ classifies the Cliffs Shaft as "hard-ore" and the Cambria-Jackson and Mather "A" as "soft-ore" types of deposit. Shaft sinking through Jasper, slate, and graywacke was in progress at this writing at the Mather "B", with completion at 3,100-foot depth in August 1949. The many different kinds of rock and ore at the mines of the Cleveland- Cliffs Iron Co. and the experimental work being carried on with carbide in- sert bits make it possible to compare, generally, the carbide insert and steel detachable bit. The type of "hard ore" at the Cliffs Shaft mine re- quired close study of the possible use of the insert tit, and their records are more complete than those of the "soft-ore" mines. History and development of tungsten carbide tips inserted in rock drill bits have been covered by R. W. Adamson, C. H. Vivian, R. C. Sullivan,5/ and others. Tungsten carbide insert rock bits have only recently been introduced to the domestic mining industry. Although unusual performance records are being reported at operations employing the insert bits, the general adaptability of the tool to all rock types and the advantages to be gained by using carbide insert tits remains to be demonstrated. Insert-bit performance is being observed at numerous mines and quarries throughout the United States The several mining operations at the Cleveland-Cliffs Iron Co. at Ishpeming, Mich., is one site where exhaustive comparative tests of insert and conventional steel detachable bits are currently in progress. Results to date are sufficiently impressive to be of general interest to the mining

Mar 1, 1950

By Harold L. Riley

This Bureau of Mines paper describes the methods and practices used at the Peck quarry of the Crab Orchard Stone Co., Inc., one of the leading producers of dimension stone in the Crossville, Tenn., area. The product is marketed under the registered trademark "Crab Orchard Stone". Another large producer of stone from the Crossville district sells its product under the registered trademark of "Tenn-Quartz". Both companies, and a number of other companies and individuals who quarry and process dimension stone from the same general geological formation, are members of the Quartzite Producers Association of Tennessee. The salable product is shipped throughout the country for use as architectural building stone. In 1959, 653,008 cubic feet of stone was produced in the Crossville area and was sold for $1,414,405. Terms and descriptions used in this report are those of the quarry and building trades. The offices, pitching sheds, wire saws, railroad siding, and storage areas of the Crab Orchard Stone Co., Inc., are on a side road 0.3 mile north from a point 2.2 miles east of Crossville, Tenn., on U.S. Highway 70. The quarry is on this same side road 2.0 miles south of Highway 70. Crossville is 62 miles west of Knoxville and 65 miles northeast of Chattanooga, Tenn.

Jan 1, 1962

By Will H. Coghill, Fred D. DeVaney, R. S. Dean

Part I CONTENTS

May 1, 1934

By L. C. IlsLey

The theory and practice followed by the Bureau of Mines in investigating electrical equipment4/ made for service in gassy mines are of particular interest not only to manufacturers but also to those organizations that deal with safety anal inspection at the mines. This publication purposes to discuss the theory upon which tests of equipment in explosive atmospheres are based and to consider inspection and other matters pertaining to investigations made by the Bureau in ascertaining whether a machine merits approval. The material in this report is taken from an earlier bulletin,5/ which is row out of print, and has been revised and brought up to date to make the information again available to manufacturers, inspectors, and others interested in the development of safe equipment.

Jan 1, 1954

By Wm. O. Vanderburg

This report on the mining and milling of tungsten ores is the second part of a general study of the domestic tungsten industry. The first part, comprising general information on tungsten, has been printed as Bureau of Mines Information Circular 6821. The purpose of these papers is to increase efficiency in the mining, preparation, and utilization of the tungsten resources of the United States. The tungsten industry forms so small a part of the vast mining and metallurgical operations of the illation that private metallurgists have not had enough inducement to give special attention to the recovery of tungsten minerals from the ores, and many of the small companies are financially unable to undertake research work. A study of the milling of tungsten ores reveals that further improvement is possible, especially in the treatment of slimes. Recent experimental work by the Bureau shows that the flotation process is applicable to certain tungsten ores. The future of the tungsten industry it the United States depends to a great extent on utilization of the low-grade deposits of the contact-metamorphic type.

Jan 1, 1935

By R. R. Sayers

The increasing use of hydrogen fluoride (annual consumption now exceeds 500,000 pounds (1)4/) directly and its occurrence as a byproduct of the utilization of fluorine compounds in the mineral industries, especially in metallurgical processes and in the refining of petroleum products, has aroused interest in its toxicity, and a brief review of the literature, with special reference to the hazard of poisoning in the mineral industries, seems to be opportune. Recently, residents in the vicinity of aluminum plants have been complaining of injury to livestock and vegetation as well as to their own health from the gases discharged into the air during operation of the plants, hydrofluoric acid gas apparently being the offender. The comparatively recent utilization of hydrofluoric acid in the alkylation process for the production of high-octane gasoline has raised the question of the hazard of poisoning in the petroleum Industry. In addition, the use of fluorine-containing refrigerants has extended the potential al exposure outside of industry (2).

Jan 1, 1945

By Jerry B. F. Champlin

NIOSHAn accelerated testing procedure developed by the Bureau of Mines for evaluating commercially available corrosion inhibitors is described. Ultra-sonic agitation of the corrodent solutions and the hot-finished mild steel test coupons was used to evaluate the effects of several variables on the effectiveness of two corrosion inhibitors. Small changes in the weight of the test coupons in both controlled and inhibited corrodents, before and after exposure, affected the precision and accuracy of the results. Minute amounts of oxygen in the systems were found to be causing the relatively large deviations in the corrosion developed in the controlled tests. Microscopic examination of the test coupons revealed that both surface preparation and internal strains resulting from fabrication methods materially affect corrosion behavior.

Jan 1, 1965

By Harry D. Jumper

This paper describing the methods of ruining a sand, gravel, and bowlder deposit 20 miles east of Los Angeles, and the classification and preparation of these materials for market, is one of a series being prepared for and published by the United States Bureau of Mines on methods and cost of mining sand and gravel. These papers are designed to disseminate technical information regarding, the methods used. The cost tabulations represent operating expenditures only and not total costs. It is recognized that publication of total costs might in many instances cause embarrassment to individual operators as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion anti study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations stall ensue. The description contained herein is typical of this industry in Southern California. ACKNOWLEDGMENT The author acknowledges tine assistance of L. L. Rogers, vice-president and manager of production and distribution for the Consolidated Rock Products Co., in the preparation of this paper.

Jan 1, 1933

By K. E. Hjelmstad

During an underground mine fire, air can be rapidly depleted of oxygen and contaminated with smoke and toxic fire gases. Any delay in warning miners could have disastrous consequences. Unfortunately, present mine fire alarm systems, such as stench, audible or visual alarms, telephones, and messengers, are often slow, unreliable, and limited in mine area coverage. Recent research by the U.S. Bureau of Mines has demonstrated that ultra low frequency electromagnetic signaling can be used for an underground mine fire alarm. In field tests of prototype equipment at five mines, electromagnetic signals from 630 to 2,000 Hz were transmitted through mine rock for distances as great as 1,645 m to an intrinsically safe receiver. The prototype system uses off-the-shelf components and state-of-the-art technology to insure high reliability and low cost. When utilized, this. technology would enable simultaneous and instantaneous warning of all underground personnel, regardless of their location or work activity, thereby increasing the likelihood of their successfully escaping a mine disaster. This report presents the theoretical basis for through-the-rock ultra low frequency electromagnetic transmission, design of the prototype transmitter and receiver, and the results of in-mine tests of the prototype system.

Jan 1, 2010

By Dennis McLaughin

This report contains a description of the contract activities performed by ENSCO, Inc. under contract No. H0178069. The purpose of this project was to enhance the Bureau of Mine?s Cableless Electronic Survey System use to aid in the drilling of long (approx. 2000 feet) boreholes in coal. This drilling is performed as part of the methane drainage program. The system that was ultimately developed was field tested 2nd demonstrated in actual in-mine drilling activities. The significance of this system as compared to previous drill survey systems is the fact that it surveys without having to be inserted and removed for each survey point. It is so designed that it can withstand the shock and vibration experience by the drill string during drilling. This means an increased productivity is now possible in that drill operators can determine drill bit positioning in a near real-time environment.

Jan 1, 1981

By Leland H. Johnson, D. O. Kennedy, John Hyvarenen

"SUMMARYA chronological list of accidents at metal and nonmetal mines and quarries (excluding coal mines) in the United States in which five or more lives were lost has been compiled. Many accidents were described in more detail because of their unusual features. Tables have been included to indicate the number of major disasters and fatalities by the principal product mined, by State, and by 10-year intervals prior to 1945. The number of men employed to indicate man-hours exposed is unavailable; therefore, a true picture of disaster data by principal product mined, by State, and by 10-year intervals is not possible. However, the data are presented to indicate the causes of major accidents and bring to the attention of those affiliated with metal and nonmetal mines and quarries the hazards involved and lessons that can be practiced to keep such accidents at a minimum.INTRODUCTIONThe Bureau of Mines was requested to compile a chronological list of accidents at metal and nonmetal mines and quarries (excluding coal mines) in the United States in which five or more lives were lost. Data have been assembled on accidents from all causes in these mines and quarries from the earliest available information (describ¬ing an underground mine fire in Nevada in 1869) to the last reported major accident (a fire at a company-owned bunkhouse in Arizona in 1945).The accounts of the accidents were taken from articles in the technical press and from published and unpublished reports of the Bureau of Mines. Many of the accidents have been selected for more detailed descriptions because of the unique circumstances and to show the variety of dangers involved.Tables are included to indicate the number of major accidents, with resultant fatalities, by the principal metal and nonmetal producing groups, by State, and by 10-year intervals previous to 1945. The interval 1869-1875 does not cover a 10-year span because of incomplete records previous to 1869.ACKNOWLEDGMENTSThe information contained in this report was obtained from the Engineering and Mining Journal from 1874 to 1947, the Mining and Scientific Press from 1908 through 1922, from various published and unpublished reports of the Bureau of Mines and from reports by State departments of mines. Daniel Harrington, retired chief of the Health and Safety Division; E. H. Denny, supervising engineer, District H; R. M. Loucks, mining engineer; and other engineers of the Division contributed much valuable information and assisted materially in the study."

Apr 1, 1949

By Samuel P. Polack

This report reviews investigations to determine the fire hazard in coal mining when using flammable petroleum hydraulic oils to actuate mining equipment and summarizes research by the Bureau of Mines and industry on fire-resistant hydraulic fluids. Tests were established to evaluate fire resistance and the necessary characteristics to assure adequate service when fire-resistant fluids are used to replace petroleum hydraulic oils. The research was conducted in the laboratory and field trials under actual operating conditions in underground mines. Bureau of Mines Schedule 30 became effective December 17, 1959; the first approval was granted on February 18, 1960, and the twelfth was granted on March 17, 1961. The approvals include nine ready-mixed (by the producer) fluids and seven concentrates to which water is added by the user according to instructions from the producer. Seven synthetic-type fire-resistant hydraulic fluids submitted by two producers are also approved. Over 100 coal mines are now using water-in-oil emulsion-type fire-resistant hydraulic fluids in varying degrees from a trial in one machine to all the hydraulic equipment in an entire mine.

Jan 1, 1961

By Sarkis G. Ampian

Crystalline silica (quartz, cristobalite, and tridyrnite) is regulated by the Mine Safety and Health Administration (MSHA) and Occupational Safety and Health Administration (OSHA) because of its potential for causing debilitating but nonmalignant lung diseases. In 1987, the International Agency for Research Against Cancer (IARC) conducted a review of the health literature and concluded that crystalline silica was a probable human carcinogen. As a result of this finding, OSHA was required to regulate crystalline silica under its Hazard Communication Standard (HCS). The standard requires that all materials handled by OSHA-regulated facilities be labeled according to the requirements of RCS and that workers receive proper training on the handling of the material if the crystalline silica content equals or exceeds 0.1 weight percent (0.1 %). MSHA currently is considering enacting its own RCS. This will be similar to OSHA's RCS. If the standard is enacted, most mineral producers will have to determine the respirable monitor filter and bulk crystalline silica contents of their ores and products so that workers and/or customers will know whether they are in compliance with the 0.1% HCS and/or the OSHA permissible exposure level (PEL) of 50 µg for an 8-hour workday for respirable crystalline silica as determined from monitor samples. Two major concerns with the RCS are the widespread occurrence of crystalline silica in nature and the suitability of current technology for routinely determining crystalline silica concentrations at the 0.1 % RCS level. Most ores are extracted from silica-bearing deposits and it is a common constituent of rocks and soils. OSHA's RCS will have the greatest impact on the producers of crushed stone, diatomite, dimension stone, gravel, industrial sand, perlite, pumice, pyrophyllite, sand, and talc because these materials frequently are shipped directly from the mill to the customer. MSHA's RCS would affect nearly all mineral producers. Those producers that have crystalline silica present in concentrations near the 0.1 % cutoff point will have the most difficulty with the analysis. Crystalline silica can be quantified at the 0.1 % level by X-ray diffractometry in simple systems containing one, two, and possibly three minerals if (1) none of the accessory minerals has X-ray diffraction reflections that coincide or overlap with those of crystalline silica and (2) the standard has a particle size distribution and crystallinity similar to those of the sample. In some instances, it may not be possible to determine the crystalline silica content of a sample with any degree of certainty using the recommended regulatory protocol. In all cases, it is recommended that a qualified mineralogist identify the minerals in a sample prior to any regulatory analysis. Additionally, the uncertainty as to whether some silica polymorphs should be classified as crystalline or noncrystalline and the suitability of metastable high-temperature standards, such as cristobalite and tridyrnite, for regulatory analysis at ambient temperatures should be addressed further. This overview is written both to highlight these problems and to serve as a guide for analysts, regulators, and industry personnel who are involved in the crystalline silica issue. It also covers some of the difficulties and/or shortcomings in quantifying crystalline silica, such as the ubiquitous mineral quartz, in the workplace.

Jan 1, 1992

By T. G. Chapman

This paper has been abstracted from a forthcoming Bureau of Mines bulletin on the concentration of copper ores in North America. GENERAL DEVELOPMENTS IN CONCENTRATING COPPER ORES FROM 1912 TO 1932 During the east 20 years the milling of copper ores as practiced in the larger concentrators has chanced to such an extent that comparatively few of the machines in use at the beginning of this period remain in service today. Concentrating Practice in 1912. In 1912 the usual equipment for concentrating copper ores comprised jigs for the coarser sizes, tables and sand vanners for the intermediate sizes, and vanners for the finer crushed and ground material. Rolls operated in series under graded crushing conditions, were in common use for the liberation of the copper minerals; grinding by Chilean or Muntington mills ordinarily was confined to the coarser tailings of jigs and tables.

Jan 1, 1934

By Albert L. Toenges

The fuel requirements for industrial and domestic consumers in New England, in normal times, are supplied almost entirely by fuel oil, anthracite, and bituminous coal. A shortage of these fuels occurred during the war. This shortage was caused by: (1) The diversion of oil to military uses; (2) the use of railroad and boat facilities that ordinarily would transport coal for the transportation of war material; (3) the inability of coal mines to apply the increased demand for coal which resulted from the conversion from oil to coal by domestic and industrial consumers; and (4) the increased demand of war industries for coal. Because of this Critical fuel situation, an investigation was made of possible sources of fuel nearer to points of consumption in New England.

Jan 1, 1948

The analysis of in-mine grounding systems began with an extensive literature search which is still in progress. About a dozen articles have been found which deal directly with grounding problems on low voltage power systems or mine power systems. These systems have special grounding problems because normal load currents can be nearly as large as many types of fault currents. Information has been collected on the influence of cable spacing) conduit geometry, location of nearby conducting structures, etc., on the magnitude and path of fault current. Many other articles have been found which are less directly related to mine ground system analysis. The in-mine ground system analysis team has also inspected portions of two mine power systems to become familiar with the practices used in grounding. One electrical engineer and several other mine personnel have been interviewed concerning mine power system grounding practice. Already several aspects of the mine grounding system have been marked as requiring special attention.

Jan 1, 1975