Search Documents

By C. A. Herbert

In summer, when hot, moisture-laden air enters a coal mine in the region east of the Mississippi River, the moisture is likely to condense on the roof and ribs because the incoming air is cooled below its dew point upon contact with the roof, ribs, and floor of the mine passageways. When the roof and ribs become wet owing to this condensation they are said to "sweat." In many mines, as soon as this sweating begins, shale or slate roof that appears solid and strong in winter begins to cut and fall. For a long time most mining men believed (many still believe) that the roof trouble was due to this sweating. However, from observation of conditions in one mine the operators concluded that the trouble was caused by expansion and contraction of the roof due to changes of temperature. This opinion was confirmed by experiments at several mines in cooling the air as it entered the mines. Methods used in these mines for cooling the air are described in this circular. MINE A At mine A the roof gave considerable trouble in the summer, and it was observed that where a spray of water from a leaking dam kept the roof wet and at a uniform temperature no difficulty was experienced with the roof, although it had cut and fallen on either side of that point. From this fact the company officials concluded that changes of temperature in the air rather than moisture caused the trouble and that if the incoming air were cooled to approximately normal strata temperature much of the additional roof trouble experienced during the summer would be overcome.

Jan 1, 1940

By Noel N. Moebs

The Bureau of Mines studied the feasibility of water diversion and overburden dewatering for underground coal mines in the Appalachian region. All relevant published literature pertaining to the occurrence and control of surface and ground water in underground coal mines was reviewed, and the impacts of mine water with respect to health and safety, production, environment, and costs were assessed and are described in this report. The report also identifies the sources of water inflow into underground coal mines, and gives a summary description and evaluation of techniques that can be used to reduce the amount of water entering these mines. Engineering practices currently used by operating coal mines in the Appalachian region to prevent the movement of ground and surface water into active coal workings were reviewed and are summarized. Major emphasis has been placed on the identification of geologic and hydrologic conditions of the site, the water control methods used, and an evaluation of their technical and cost effectiveness.

Jan 1, 1985

By V. F. Parry

The major industrial uses of char or semicoke produced by low-temperature carbonization of coal4/ are as fuel for generating electric power, for blending with metallurgical coking coal as a substitute for low-volatile coals, and for gasification to produce synthesis gas for chemical purposes. This paper discusses various methods for carbonizing coal, emphasizing processing of the noncoking coals to produce char for thermal power-plant fuel and for blending with metallurgical coking coals and tar for chemical use. Low-temperature carbonization is a relatively simple processing step involving heating coal to about 900° to 1,200° F. to decompose the coal into 4 main products: (1) Semicoke or char; (2) complex, partly oxygenated liquid hydrocarbons or tar; (3) fixed gases; and (4) water. If the coal is heated rapidly under conditions that prevent decomposition of the primary products, 68 to 87 percent of the net heat in the raw coal is left in the char and 10 to 23 percent of the potential heat appears in the primary tar. Fixed gases represent approximately 7 percent of the heat and approximately 2 percent is lost or dissipated in the reactions of decomposition. Considering the different ranks of coal in the United States, the yield of tar will vary from about 9 to 44 gallons per ton, therefore it is important that each coal be carefully considered if it is to be carbonized for industrial use.

Jan 1, 1955

By L. Crocker

The Bureau of Mines investigated processes for recovering a marketable lithium product from the montmorillonite-type clays of the McDermitt caldera. The clay deposit, located on the Nevada-Oregon border, is estimated to contain over 3 million short tons of lithium. Limestone-gypsum roasting and selective chlorination proved most successful for extracting lithium from the clays; 80-pct Li recovery was achieved using either technique. With both processes, lithium silicate in the clay was converted to a water-soluble compound-either lithium sulfate or lithium chloride. The lithium was then recovered as a carbonate by water leaching the calcine, concentrating the leach solution by evaporation, and precipitating the lithium with soda ash. The operating costs for the limestone-gypsum roast process were estimated at $2.02/lb Li2C03; selective chlorination operating costs were estimated at $3.85/1b Li2C03. The current selling price of Li2C03 is about $1.50/lb. A detailed flowsheet, material balance, and process evaluation are presented for the limestone-gypsum roast process. In addition, lithium reserves and resources are discussed and the McDermitt clays are described.

Jan 1, 1988

By M. Orchin

THIS PAPER is concerned with two aspects of the behavior of coal: (1) Dispersion by solvents atmospheric pressure and high temperature and (2) the destruction and regeneration of the coking properties of coal. Several pure polycyclic compounds and a coal-tar fraction were found to extract 95 percent of the organic material of a bituminous coal. About 20 percent of the extract was soluble in benzene, and this fraction contained the ?coking principle? of the coal. From an extensive chemical spectroscopic, and x-ray study of the benzene-soluble material, some conclusions could be drawn concerning the composition and structure of this fraction of coal. A possible commercial application of the extraction technique is in the preparation of low-ash carbonaceous material for the manufacture of electrode carbon.

Jan 1, 1951

By F. W. Wood

A program of research was conducted by the Bureau of Mines to investigate anomalies in electrical-discharge behavior during consumable-electrode arc melting of titanium and to study the effects of these irregularities on arc-furnace explosions. A major effort was devoted to an experimental survey of arc behavior and a qualitative definition of discharge phenomena.3/ An important conclusion was that the "glow" of industrial arc-melting terminology is not a glow discharge but a skittering arc in a displaced position. The conditions that permit displaced skittering were tentatively defined. The displaced skittering arcs tended to damage melting crucibles in two ways, and details of possible mechanisms leading to crucible rupture and explosive reactions have been proposed accordingly. However, no acceptable means of preventing crucible damage was discovered.

Jan 1, 1961

By G. L. Oldright

As sponge iron is much like porous, coarse sand, it is a tempting material to use in place of coarse scrap iron as a precipitant of metals, for scrap iron is relatively awkward to handle and exposes only a small amount of surface to pregnant solutions. The results of the experiments described in this bulletin are largely a record of the behavior of sponge iron as a precipitant of lead and copper under laboratory conditions comparable to those that would obtain in a commercial plant were it attempted to secure the maximum contact of surface between solution and precipitant. Physically, the study is largely one of the rates of diffusion of the metal ions in the solutions and through the metallic coatings surrounding the sponge iron particles. The practical objectives are to remove completely the valuable metals from solution and at the same time to obtain a precipitate of good grade. In order to fulfill this latter requirement, the precipitant should be almost completely consumed. These practical ends are usually secured by having the two substances involved pass each other counter-currently-that is, in such a manner as to have the strongest precipitant in contact with the most impoverished solution, and vice versa. EXPERIMENTS WITH LEAD SOLUTIONS In nearly all of the schemes involving the leaching of lead from its ores the metal has been put into solution as the chloride, and fairly concentrated liquors have been employed. The solubility of lead under such conditions is comparatively small at best; the hot pregnant liquors from which the metal is to be precipitated are then made nearly saturated with respect to lead, and only a very small amount of acid is used. Therefore it was not as necessary to learn the behavior of the sponge iron in precipitating lead from solutions of widely differing composition as to learn under what conditions, and with what mechanisms, this precipitation might be carried out most readily.

Jan 1, 1928

By Mark P. Meyer

This U.S. Bureau of Mines publication presents salient information in abstract form on 247 coal deposits in Alaska. Coverage includes currently producing deposits and deposits that appear to have commercial production potential. Data arc taken from coal properties identified by the U.S. Bureau of Mines minerals availability program and by a literature search. Infrastructural and institutional factors affecting coal development in Alaska are also discussed.

Jan 1, 1987

By Raymond G. Travis

This report describes coal-mining methods, power requirements, coal production and distribution, and coal resources of the Bull Mountain coal field in Musselshell and Yellowstone Counties, south-central Montana Investigations in the field, were conducted by Bureau of Mines engineers The report contains a short summary of the geology and geography of the field and discusses the following information secured during the field study: Method of mining practiced at each mine, including a description of each phase of the mining cycle. Coal produced and its distribution at each mine. Power requirements and the consumption of electricity per ton of coal produced by mines. Number of non employed by mines, and the production per man per shift underground and the over-all production per man employed. Estimates of future production and power requirements for the field as a whole. This information should be of benefit to any company or individual planning the development of now coal mines in the area or the expansion of present operations.

Jan 1, 1950

By Walter D. Holland

LFE Environmental performed an Industrial Hygiene survey of the Paraho Oil Shale Mining and Processing facility in Anvil Points near Rifle, Colorado, on August 6 and 7, 1975. This survey consisted of an investigation of the underground operations for diesel emission contaminants and of the above ground work areas for all inhalation contaminants other than silica dust. Samples were collected to investigate the following contaminants: respirable dust, total dust, NO2, NO, H2SO4, formaldehyde, CO2, S02 and CO. None of the determinations of contaminants in the underground operations indicate air concentrations exceeding their standards. The results for the samples collected above ground indicate only one operation where the employee's exposure exceeds the standards. It is a welding operation where the standards for total dust and lead are exceeded. Since the survey the employer has installed an exhaust ventilation system which has significantly reduced the welder's exposure.

Jan 1, 1976

By H. C. Miller

The success of any project in which gas is injected into oil-producing sands to increase the current rate or the economic ultimate production of oil or in which surplus gas from oil producing operations is stored temporarily in reservoir sands that have been wholly or partly depleted of their producible oil depends mainly upon an understanding of the underground movements of oil, water, and injected gas and the ability to control their speed and direction of migration through the reservoir sands. Many operators believe that injected gas always travels up the structure and drives oil to wells structurally higher than the injection wells, because the specific gravity of the injected gas is less than that of the fluid substances in the formation. Consequently, many injection wells are located on the flanks of oil-bearing structures with the idea of utilizing the energy of the injected gas to drive the oil to producing wells higher on the structure. It is true, under certain conditions of pressure and fluid depletion of the reservoir sands, that injected gas will move in an up-structure direction, but the theory that injected gas always moves up the structure is based on an erroneous conception of the laws that pertain to the expansion of gases. By definition, "a gas is distinguished by its property of infinite expansion and is limited in volume only by the walls of the vessel which contains it."3 The expansion of gas that is injected into reservoir sands also is limited by "walls" that surround the space influenced by the injected gas. The walls of the majority of undrilled or virgin oil-bearing reservoirs in California are the impervious shales overlying and underlying the productive strata and the "dams" or effective barriers of edge water around the rims of the reservoirs. When gas is injected into the sands of a producing reservoir, regardless of the location of the injection well on the structure or the degree of depletion of oil from the sands, one of the walls which confine the gas in the structure about the injection well is fluid. This wall will be edge water in a nearly depleted reservoir, where the drainage cones or regions of reduced pressure about injection and producing wells intersect; and, where there is no interference of drainage cones and the injection well is structurally above the edge water, the wall will be oil. In some producing reservoirs bottom water may be the lower wall of the space that confines the gas about injection wells, but the effect of bottom water on limiting the expansion of gas is the same as if the water was not present and impervious formation separated the producing from the underlying nonproducing strata. Therefore, since compressed gas always seeks regions of reduced pressure and its final volume is limited only by formation and fluid barriers and since the force exerted by the gas under pressure is equal in all directions, the course of migration of injected gas in reservoir sands in California and the

Jan 1, 1932

By R. A. Beall, S. L. Ausmus

The development of a completely water - free expendable graphite mold material , useful for reactive metal castings , has been detailed . Mixing and curing variables have been evaluated both by physical testing of the material itself and by castings of titanium , zirconium , and hafnium . The blend of powdered graphite , cornstarch , dextrin , cereal binder , linseed oil , and Carbowax -4000 is a successful mix when mulled in a carbon dioxide atmosphere , and properly cured and fired . The primary advantage of this material is its adaptability to standard foundry techniques ; i . e . , core blowing and hand ramming . Temperatures in the curing and firing cycles do not exceed 960 ° C , and no vacuum firing is required .

Jan 1, 1964

By Dean H. Ambrose

This Bureau of Mines publication summarizes the status of mine electrical equipment reliability research. Failure rate data were estimated from theoretical, laboratory, and field studies. Tables are presented listing reliability characteristics of molded-case circuit breakers, undervoltage relays, ground check monitors, cables, motors, and control circuitry. Application of failure rate data is shown in tables listing maintenance scheduling intervals of components and components that are most sensitive to the probability of hazardous voltages on power distribution systems in the mines. Complete, accurate, and appropriate failure rates on mine equipment are of the utmost importance for reliability evaluations.

Jan 1, 1985

By David Schlain

IN 1942 the Bureau of Mines began to develop the Kroll process for use in the large-scale production of titanium. Titanium and titanium alloys are now commercial metals. These metals are relatively expensive, but It is now evident that they will have important industrial uses and that in many instances these will be related to their remarkable corrosion resistance. This bulletin presents the known corrosion properties of titanium and its alloys in useful form. In marine environments titanium is highly resistant to corrosion and does not pit, or undergo crevice corrosion, stress corrosion, or corrosion fatigue. Titanium is also highly resistant in many salt solutions, including most chlorides. It is very resistant to corrosion in nitric acid solutions. It is also resistant to white fuming nitric acid. However, it may react violently with red fuming nitric acid. In phosphoric acid solutions titanium has rela¬tively good resistance to corrosion, but it has less resistance to sulfuric acid and still less to hydrochloric acid solutions. Titanium corrodes very rapidly in hydrofluoric acid Solutions. It is very resistant to corrosion in many organic chemicals. However, it has only moderate resistance to formic acid solutions and poor resistance inn oxalic acid solutions. Titanium does not corrode in dichloroaretic acid but, corrodes rapidly in 100 percent trichloroacetic acid at 100° C. Titanium is resistant to barium, calcium, magnesium, ammonium, and sodium hydroxides. Titanium is inert in wet chlorine, bromine, or iodine gases. However, in dry chlorine gas titanium reacts rapidly enough to ignite. It also reacts rapidly with dry bromine gas, but, it is resistant to dry iodine gas. When titanium is exposed to red fuming nitric acid solutions with high nitrogen dioxide content and low water content, it corrodes, undergoes stress-corrosion cracking, and becomes pyrophoric. This occurs more readily with some titanium alleys, such as titanium-8 percent manganese. A fresh titanium surface immersed in water or in an aqueous solution and in contact with an oxygen-rich atmosphere under sufficientt pressure is unstable and will ignite spontaneously. Inherently an active metal, titanium has a tendency to become less active in environments containing oxidizing agents such as air, oxygen, chlorine, or ferric, cupric, or platinic ions. Titanium is more noble than most structural metals in roost, environments and its excellent corrosion resistance is generally not, affected by contact with these metals. However, some of the other metals corrode faster because of contact with titanium. Titanium undergoes anodic polarization readily, so that even when it is the less noble member of a galvanic couple it may corrode less because of the contact. Titanium alloys often have corrosion properties and electrochemical characteristics similar to those of commercially pure titanium. Titanium alloys containing noble metals, zirconium, molybdenum, vanadium, tantalum, or copper sometimes have better corrosion resistance than pure titanium.

Jan 1, 1964

By Horace C. Porter

Much has been written of the changes undergone by coal in storage and the deterioration of coal through exposure to the weather. In order to obtain definite information for the benefit of the Government departments and of all who store coal in large quantities, a series of tests was begun in the fall of 1909 under the supervision of J. A. Holmes, then chief technologist of the United States Geological Survey, and was continued by the Bureau of Mines after its establishment in 1910. The tests were confined to determinations of the loss in heating value of the coals and did not include a study of other deterioration; for example, in coking quality or the yield of by-products in coking. The Bureau of Yards and Docks of the Navy Department cooperated in tests of New River (W. Va.) coal, a variety largely used by the Navy. A preliminary report presenting a brief account of the early results of these tests has been published by the Bureau of Mines as Technical Paper 16.a The detailed report is presented in this bulletin, which gives a full account of the tests and the analytical data covering a period of five years' storage. Data of somewhat similar experiments for shorter periods with gas coal from the Pittsburgh bed, with Pocahontas coal on the Isthmus of Panama, and with Sheridan, Wyo., subbituminous coal, which is used for railroad and other purposes in the West, are included.

Jan 1, 1917

By E. P. Youngman

Tantalum is a rare element ; estimates indicate that there is less tantalum than gold in the earth's crust . After remaining a laboratory curiosity for many years , it was used to a limited extent and for relatively few years (1903- 1911) for incandescent electric-light -bulb filaments . Another wave of interest in tantalum appeared when its electrolytic-valve action was taken advantage of in charging storage batteries , especially for radio work . Tantalum chargers were eventually displaced by other types of chargers , but for a time they were manufac tured in sufficiently large numbers to create a demand for the metal and to bring about its production on a commercial scale in the United States . As tantalum became available in larger quantities and at substantially lower prices , and as high prices for platinum encouraged the employment of tantalum as a substitute , the metal was put to many new uses . Ferrotantalum was made and sold before the World War , and patents have been taken out for a number of special alloys for industrial purposes , but probably the largest use for the metal to-day is in vacuum tubes .

Aug 1, 1930

By Robert W. Ageton

The Bureau of Mines investigated the in situ vertical component of the rock stress in the rib of the haulage drift on the 6100-level of the Star mine, Burke, Idaho, using the flatjack and borehole deformation methods. The estimate of the vertical component of stress about 2 feet into the rib at a station along the haulage drift on the 6100-level of the Star mine by the flatjack method is approximately 5,875 psi, whereas the borehole deformation procedure at this station yielded a value of 5,500 psi for the same depth into the rib. The test zone is approximately 5,625 feet below the surface.No attempt was made to extrapolate stress estimates beyond the depth of the flatjack installation.

Jan 1, 1967

By W. H. Frederic, F. H. Gibson, R. F. Abernethy

This publication contains the quantitative values for phosphorus , chlorine , sodium , and potassium in United States coals . The samples tested were taken from commercial shipments and have been selected to represent the principal coal producing areas of the country . Due to combining the analytical results from two separate surveys , values for the four elements are not available for all samples .

Jan 1, 1965

By Pamela J. Watson

A novel technique has been employed by the U.S. Bureau of Mines to determine the zeta potential of particles for a far-reaching series of material types in a wide variety of baseline waters, both alone and with many different chemical additives. The materials tested ranged from naturally occurring Sioux Quartzite and Tennessee marble to commercially produced magnesium oxide bricks. The waters tested ranged from ultrapure distilled, deionized water to municipal tap water and mine-site water. The chemical solutions tested included inorganic additives, such as aluminum chloride (AICI3) and sodium chloride (NaCl); organic additives, such as dodecyltrimethyl ammonium bromide (DTAB); and nonionic polymers, such as polyethylene oxide (PEO). The results of precise zeta potential determinations have application in a large number of laboratory studies as well as in various mining and processing operations.

Jan 1, 1989

By Paul M. Tyler

Graphite is an essential war mineral and for that reason has received much attention from the standpoint of national defense. During the World War the situation with respect to graphite supplies, though it never became acute, caused considerable concern. Even in peace time, however, graphite has aroused more interest than the actual size of the industry seems to warrant. Despite this wide interest the facts of the industry do not seem to be generally known. Often there has been an almost total disregard of the essential' economic and technical problems involved. Long ago Bastin3 made the following statement; in a Government' report: "To-day there are more abandoned mines and mills in the United States than the number in operation * * *. In the number of times' some of these properties have changed hands in the course of a few years, there is a record of misrepresentation and disappointment that can hardly be equaled in any other branch of mining; and many properties have been notoriously associated with stock manipulation of doubtful character." According to one authority fully 600 graphite mines have failed in the United States, and the record shows that of all these properties scarcely a score have ever succeeded in operating for as much as a year or two. More than 40 mines have been worked at various times in the State of New York alone and at least that many in Alabama. Throughout the country, in fact, there are scarcely a dozen States in which efforts have not been made at some time to exploit graphite deposits. At the present time the list of mines that can be classed as at all active is reduced to less than ten. Failures inevitably occur in all lands of mining, but the disheartening feature of the record of graphite mining in this country is that so few ventures have even paid back the money put into them and. that none has been a conspicuous success.

Jan 1, 1929