Search Documents

By W. D. Walker

This information circular is offered to the coal-mining industry for use as a guide in selecting, placing, and caring for fire-fighting equipment in coal mines. Its purpose is to suggest minimum requirements for fire protection underground, and it is presented with the hope that it will aid in establishing adequate standards that will provide reasonable protection against underground fires in coal mines. Potentially, a coal mine is a hazardous fire area. Coal itself is a combustible substance, easily ignited. In addition, large quantities of other combustible materials must be present in the area of operations; these include materials for roof support, track ties, doors, ventilation stoppings, lubricants, etc.

Jan 1, 1953

By R. Barany

Thermodynamic calculations pertaining to the minerals gibbsite, kaolinite, halloysite, and dickite have been hampered by the lack of adequate heat and free energy of formation data. Previous data for gibbsite were highly uncertain, and there were no data for the other three substances. By use of hydrofluoric acid solution calorimetry, the Bureau of Mines derived heat of formation values from the elements and from the oxides for the four substances, and the data were combined with known entropy values to obtain the corresponding free energies of formation. The results show that gibbsite and halloysite are thermodynamically unstable with respect to the oxides (a- alumina, a- quartz, and liquid water) at 298.15° K,, while kaolinite and dickite are only moderately stable (to about the same degree), The instability of halloysite, in comparison with kaolinite and dickite, results in a 60°-lower equilibrium decomposition temperature.

Jan 1, 1961

The value of raw nonfuel mineral materials production totaled an estimated $19.7 billion in 1978. The record 1978 value exceeded by 13 percent the 1977 value of $17.5 billion. This raw mineral output was the basis for approximately $200 billion worth of processed materials of mineral origin. Output of both metals and nonmetals increased about $1 billion each, above comparable figures for 1977. Of the 22 metals produced quantitative output of 11 increased and the value of 13 increased. Among the 48 nonmetallic commodities produced, the quantities for 35 increased, and the values for 40 increased.

Jan 1, 1979

By Robert A. Jankowski

The Bureau of Mines has recently identified five major factors that contribute to high respirable dust levels on the six U.S. longwall faces having the most difficulty complying with Federal dust standards: (1) a poorly structured cutting sequence, (2) a poorly designed external water spray system, (3) marginal waterflow to the cutting drums, (4) minimal controls at the stage loader and crusher, and (5) the lack of effective controls for dust generated during support advance. The results of this survey illustrate the need to address all the major sources of longwall dust generation and the need for mine operators to implement a variety of control procedures to assure compliance. The Bureau of Mines will continue to assist mine operators in implementing improved dust controls and will work to identify and evaluate controls for dust generated during support advance.

Jan 1, 1983

By Jr. Sillers

This is the sixth report of investigations in cooperation with the steel industry to establish the technological acceptability of electrolytic manganese in steelmaking processes. The bulk of the .electrolytic manganese used in these tests was produced by the Bureau Of Mines from domestic ores at its Boulder City, Nev., pilot plant by the process developed by the Bureau. Electrolytic manganese for the first series of tests made in 1940 was supplied by the Electro manganese Corp., Knoxville, Tenn. The first report dealt with the application of electrolytic manganese to the manufacture of stainless.steel;9 the second with tests in acid electric and acid open-hearth low and medium carbon-steel castings; the third with its use in rimmed and? killed low-carbon steels; the fourth with its application to the manufacture of stainless steel as well as the Timken 16-25-6 alloy for gas turbines; and the fifth with tests in acid and basic electric steel foundry practice and basic steel ingot production.

Jan 1, 1948

By Philip C. Good

Preliminary studies showed that direct hydrolysis of H2SiF6 to SiO2 and HF at elevated temperatures was subject to many mechanical difficulties, and that corrosion of construction materials was a serious problem. Elimination of SiO2 from the HF product was generally poor. An alternative procedure, hydrolysis of lime-neutralized H2SiF6 by steam at 950° to 1,100° C, yielded a product very low in SiO2. Condensates containing up to 300 g/1 HF were prepared.

Jan 1, 1968

By J. D. Davis

THIS report gives results of an investigation of the carbonizing properties of the following eastern Kentucky coals: Elkhorn No. I bed, No. 28 mine, Wayland, Floyd County; Elkhorn No. 2 bed, Turner No. 5 mine, Drift, Flood County; Leatherwood (Haddix No. 5) bed, Leatherwood mine, Leatherwood. Perry County; and Harlan bed, Path Fork mine, Path Fork, Harlan County. The carbonizing properties were determined by Bureau of Mines-American Gas Association (BM-AGA) tests at 800° and 900° C. and by expansion tests in the sole-heated oven. Plastic properties were determined by tests in the Gieseler and Davis plastometers. The coals were tested singly and as blends with 20- and 30-percent low-volatile Pocahontas No. 3 coal. The dry, mineral-matter-free, fixed-carbon content of the carbonizing samples ranged from 56.7 percent for Elkhorn No. 2 to 59.7 percent for Leatherwood, and the heating values on the moist, mineral-matter-free basis ranged from 14,420 B. t. u. per pound for Elkhorn No. 2 to 14,720 for Harlan. The percentage of ash ranged from 2.9 to 6.1. The fluidity of three coals, measurer. In the Gieseler plastometer, ranged from 230 to 670 dial divisions; the fluidity of Elkhorn No. 2 could not be determined by this method. Blending lowered the fluidity of each coal; the fluidity of the blends containing 20 and 30 percent Pocahontas No. 3 ranged from 16 to 53 and from 8 to 17 dial divisions, respectively. Agglutinating values determined on silicon carbide-coal mixtures in the ratio 15:1 ranged from 3.8 to 6.3.

Jan 1, 1952

By J. D. Marchant

The Bureau of Mines studied solid-state electromigration to determine the value of the technique as a method of purifying cerium metal. Cerium metal in bars 6 inches long and 1/2 inch in diameter was refined at 600° C by solid-state electrolysis to remove iron, copper, and manganese. Iron and manganese were electrotransported to the anode and copper was electrotransported to the cathode. The concentration of iron at the anode of a cerium bar was 800 times greater than the concentration at the cathode. The concentration of manganese at the anode was twice the value at the cathode. The concentration of copper was 170 times greater at the cathode than at the anode. A radiotracer technique was used to follow the iron migration in the cerium metal. Molybdenum, silicon, and aluminum impurities were not electrotransported.

Jan 1, 1967

By M. M. Barr

Rapid expansion of the titanium-metal industry focused attention upon ilmenite as a possible substitute for the more expensive and less abundant rutile in producing titanium tetrachloride. Most of the rutile available for this use is imported. Preliminary studies were undertaken to determine the chlorination characteristics of high-titanium slags produced by electric-arc furnace smelting of alluvial Idaho ilmenite at the Federal Bureau of Mines Northwest Electrodevelopment Experiment Station, Albany, Oreg. Low silicon, calcium, and aluminum contents of the slags enhanced their potential value for chlorination.

Jan 1, 1958

According to industry representatives, U.S. producers were listing unalloyed 95.5 percent aluminum ingot in October at 53-57.5 cents per pound, but reportedly much is being priced at 53 cents. New York dealers raised their October positions by about 3 cents to 56-56.5 cents, mainly to cover spot supply shortages. London Metal Exchange 3-month forward contracts traded up in October from 52.3 to 57.3 cents per pound and closed at 56.4 cents. ASBESTOS The Jaquays Asbestos Corp. has announced the imminent closure of its mine and mill in Globe, Arizona. This is the last asbestos producer in the State having operated continuously, except during the early thirties, since 1914. Cost of compliance with environmental regulations was given as the reason for closure.

Jan 1, 1978

The Florida phosphate industry currently produces more than 80 pct of the total U.S. marketable output of phosphate rock. Because phosphate is one of three principal nutrients used in formulating a complete fertilizer, it is imperative that an uninterrupted supply of this material be available to meet the agricultural requirements of the United States while maintaining a viable phosphate industry which is competitive in world markets. As a result of an evaluation made by the Bureau of Mines, five areas were identified that affect the overall production and projected growth of the phosphate industry in Florida. These areas relate to the technological ability of the industry to comply with environmental regulations and performance standards by using the best available technology. The most significant technical problem facing the industry is the management of the clay fraction rejected during the beneficiation of phosphate ores. Other areas of concern are environmental restrictions and regulatory requirements, issues associated with mining and reclamation of wetlands, reclamation of other disturbed lands, and consumptive water use. Each of these areas is reviewed, with major emphasis placed on the current state-of-the-art processes for treatment and management of phosphatic clays.

Jan 1, 1983

By Juel H. Stears

Research was done to determine if a hydraulically operated penetrometer developed by the Bureau of Mines could be used to estimate the roof-bolt anchorage capacity of mine roof rock. Tests were conducted both in the laboratory using cement cylinders and underground in shale rock. Hardness readings were measured by the penetrometer around the periphery of the bolt holes at the anchorage horizon. Roof bolts Nere then installed and subjected to an anchorage test. The results showed that the penetrometer readings could be used to determine the optimum stratum for roof-bolt anchorage but could not be used to make an accurate estimate of the anchorage capacity.

Jan 1, 1965

By Parry. V. F.

"INTRODUCTION Coal is a compressed mass of heterogeneous, macerated, metamorphosed plant remains that have collected in the earth's crust. Probably no two beds of coal have identical properties, and different parts of the same bed may vary considerably when measured by some of the many empirical tests that have been developed to classify or differentiate the properties of coal. Because of this great variability in properties, the commercial processing of coal to produce coke and byproducts has developed largely as an art based on experience, rather than as a science. Much empirical chemical research, however, has been and is being conducted on coal carbonization, and this work is of practical value in obtaining larger yields of gas and byproducts and in the improvement of the physical properties of the coke.Both ultimate and proximate analyses have been used for correlating purposes. 3/ In the United States the proximate analysis is used for the classification of coal according to rank and grade. The proximate analysis can be employed usefully in the coal—carbonization industry because separation of the combustible matter of coal into volatile matter and fixed carbon is, in fact, a small carbonization test conducted on 1 gram of coal heated in a platinum crucible.Small—Scale Laboratory Coking Tests,Many empirical tests have been devised for determining the coking properties and measuring the yield and quality of gas and byproducts obtainable from various coals. These tests, made on samples ranging from 25 grams (about 1 ounce) to 5 kilograms (11 pounds), furnish information that is roughly proportional in practical value to the size of the sample carbonized. However, the cost of the carbonization test also increases with the amount of the sample, so that for preliminary surveys of a number of coals, samples of 25 to 1,000 grams usually are employed."

Dec 1, 1939

By T. L. Johnston

A review of technical literature of the last quarter century discloses that much experimental work has been carried on in an effort to develop commercial processes for making sponge iron. In addition to the work that has been recorded, other work has been done the results of which have not been published. The degree of success or failure of these investigators does not detract from the fact that the problem has its challenging aspects and practical possibilities that encourage further investigation. The purpose of this report is to record information derived from recent experimental work that .had its 'objective the development and demonstration of one method of producing sponge iron. Work of other investigators was studied and applied wherever possible.

Jan 1, 1948

By Jasinder S. Jaspal

Most of the underground coal in the United States is mined via room-and-pillar mining methods with continuous miners. These machines operate intermittently because they have to wait for shuttle cars to interchange positions. To overcome this discontinuity in shuttle car haulage and to realize the full production potential of continuous miners, the U.S. Bureau of Mines developed a multiple-unit continuous haulage (MUCH) system through a research contract with Jeffrey Mining Machinery Div. (JMMD). The MUCH system consists of 12 rubber-tired vehicles and a bridge conveyor. The rubber-tired vehicles are connected by a unique mechanical linkage system to form a 250-ft train. The mechanical linkage permits the vehicles to track-retrack the preceding vehicle in both inby and outby directions. The cut coal cascades from one vehicle to another until it is discharged on the section conveyor belt. The MUCH system provides continuous haulage to the continuous miner. The MUCH system was initially surface tested by JMMD. Subsequent extensive testing was conducted by the Bureau at its test facilities at Bruceton, P A. Deficiencies found during testing were corrected. This report summarizes initial tests by JMMD and subsequent extensive tests and evaluation by the Bureau.

Jan 1, 1989

By Albert L. Toenges

[During the past few years there has beer trend away from locomotive haulage of coal from the loading point to the preparation plant of bituminous-coal strip, miner to motorized. haulage. The question has arisen whether this is always economical, and the purposes of this investigation is to determine, if possible the economic limit for motorized haulage. The operators of strip coal mines and of open-pit ore mines have shown great interest in this problem, and it is thought that the findings of this investigation will. Provo helpful to them.]

Jan 1, 1938

This publication contains eight papers presented at a Bureau of Mines Technology Transfer Symposium in Charleston, W, on June 22, 1983, Five of the papers describe the results of Bureau-sponsored research on cabs and canopies for low-coal underground mining equipment. The other papers describe the efforts of three underground coal mining equipment manufacturers (FMC, Joy, and Lee-Norse) in the area of cab and canopy design.

Jan 1, 1985

By John Redington

This paper describing the milling practice at the Coniaurum Mine is one of a series of papers on milling methods, practice, and costs prepared in cooperation with an published by the United States Bureau of Mines. The 500-ton will of the Coniaurum Mines (Ltd.) is located at approximately the center of the company's property and a little more than a mile from the town of Schumacher, Ontario. The main shaft through which all the ore is heisted is adjacent to the mill so that the ore hoisted in a 3-ton skip is dumped directly into a 15-ton bin at the crusher.

Jan 1, 1931

By S. J. Pearce

The need for a simple, very sensitive, and accurate method for the determination of benzene in blood and urine vas evident throughout a recent study of chronic benzene (C6H6) poisoning conducted cooperatively by the United States Bureau of Mines, The Barrett Company, and the producers of benzene. A combustion method which will be described in a later publication, and a previously described/ adaptation of Smyth's method were developed and used during that investigation. The adaptation of Smyth's method gave satisfactory results when dealing with exposure conditions that produced chronic poisoning in a comparatively few days, but it was time-consuming; and lacked the accuracy necessary for a study of the absorption, distribution, and fate of benzene in the body during exposure to threshold concentrations of benzene vapor in air. The combustion procedure was satisfactory from the standpoint of sensitivity but was cumbersome, intricate, time-consuming, and required the use of special and somewhat expensive Physical and chemical apparatus. Following the termination of this study of chronic poisoning, possibilities ides for developing better methods occurred, and these have been investigated by the Bureau of Mines with the aid of Relief Works Division personnel microcolorimetric method for the determination of benzene in air has been described recently.6/ The present report deals rich the adaptation of this new colorimetric method to the determination

Jan 1, 1936

By Theodore M. Katz, W. Stephen Brightwell, David E. LeGrande, Joseph J. Hurrell, Jane A. Lipscomb, Nancy Lessin, Lawrence R. Murphy, Michael J. Colligan, Steven L. Sauter, Richard A. Lippin

Revolutionary changes in the organization of work have far outpaced our knowledge about the implications of these changes for the quality of working life and for safety and health on the job. This gap in knowledge is one of the 21 priority areas for research under the National Occupational Research Agenda (NORA)—a framework crafted by the National Institute for Occupational Safety and Health (NIOSH) and its partners to guide research into the next decade. This report was developed under NORA as the first attempt to develop a comprehensive research agenda for investigating and reducing occupational safety and health risks associated with the changing organization of work. Research and development needs identified in the agenda include (1) improved surveillance mechanisms to better track how the organization of work is changing, (2) accelerated research on safety and health implications of the changing organization of work, (3) increased research focus on organizational interventions to protect safety and health, and (4) steps to formalize and nurture organization of work as a distinctive field in occupational safety and health.

Jan 4, 2002