Search Documents

By Robert T. Beckman

The results of a preliminary investigation of compressive strength versus length-diameter (L/D) ratios of potash specimens and the statistical treatment of the data are summarized in this report. The purpose of the study was to evaluate a laboratory method for obtaining estimates of the strength of potash pillars during robbing operations. The specific objectives of this preliminary investigation were to test the method and the reliability (confidence limits) of the data, and to determine the number of additional specimens necessary for given confidence limits. The specimens were taken from three sites at two mines in New Mexico. The statistical analyses included the determination of the confidence limits for the data and the number of additional specimens necessary to obtain confidence limits of ±500 and 100 psi. The testing method was found acceptable, and estimates of the comprehensive strength, within 1500 psi, could be obtained by testing about 110 additional specimens from the three sites. The compressive strength of the specimens tested fits an empirical equation of the type

Dec 1, 1963

By David J. Kusler

This report describes a primary or direct, continuously sampling, and automatically averaging gravimetric method for analyzing gaseous mixtures of carbon dioxide, carbon monoxide) hydrogen, and (by volume measurement) nitrogen. The gaseous mixture is analyzed by passing it at a controlled and definite rate through a system that permits carbon dioxide and water retained by appropriate absorbents to be determined and the residual-gas volume (essentially nitrogen) to be measured. The accuracy and dependability have been established by comparison with very carefully conducted Orsat analyses. The method was developed for, and has been satisfactorily applied to, the analysis of blast-furnace top gas. It permits relatively attention free operation, using simple and low-cost materials usually found as basic equipment in the analytical laboratory. It provides, over a wide range of time or sampling intervals (from less than 1 to over 24 hours), the average composition, in terms of volume-percent, for those components usually determined in blast-furnace gas, if (as is usual) the flow rate of gas from the blast furnace is essentially constant over a selected analysis interval. Oxygen and methane are not determined; but, since these gases are normally absent or present only in traces, their analysis is seldom required.

Jan 1, 1959

By THEO L. JOHNSTON

In preparing for war , Japan built an iron and steel industry that ranked high with other industrial nations . Deficient in raw materials for making iron and steel , it had to acquire the bulk of its iron ore and much of its coal and scrap iron from foreign sources . Steel manufacture, and fabrication , however , were reserved mostly for the Home Islands , where modern integrated plants produced the implements of war . The vulnerability of relying on imports during the war was recognized early, and steps were taken to exploit iron-ore deposits and develop treatment processes on the Home Islands in order to be as self - sufficient as possible . Although the industry had expanded considerably, the capacity of the large plants still was insufficient for military requirements, so other meth- ods of producing iron and steel were adopted, which in some ways illustrate the desperate effort made to supply the war machine. In developing the iron and steel industry, modern practices of other countries were studied and followed with modifications to suit Japanese con- Aitions. German and American technical ability and equipment played a large part in the program; however, the Japanese had competent furnace technologists capable of obtaining proper equipment performance. For the most part, the standard practice consisted of smelting iron ores in blast furnaces and then refining the pig iron to make steel in open-hearth furnaces. Electric furnaces played an important part, especially in the manu- facture of alloy steels. Various other methods yielded minor but significant production. Among the various other treatment processes used, the production of sponge iron in rotary kilns 'probably was the most important in producing melt- ing stock for steel making. Of special importance was the fact that sponge iron made from low-grade ores contained critical metals, such as nickel and chromium, so that the results were more significant than was generally believed.'

Mar 1, 1948

By R. H. Church

As part of the research effort of investigating the effects of microwave energy upon the chemical and physical properties of different minerals and ores, the Bureau of Mines has conducted basic research into identifying those properties of minerals that are affected by microwave energy, namely, the dielectric constant and loss tangent. These properties were determined utilizing the theory of microwave propagation in a coaxial waveguide filled with a dielectric material and measuring the input impedance with an RF impedance analyzer that operates from 1 MHz to 1 GHz. By knowing the microwave frequency and filling the waveguide with a powdered mineral, the dielectric properties of the mineral sample were determined. From these dielectric properties, theoretical microwave heating characteristics of each mineral could be calculated. These same mineral samples were then irradiated by a 915 MHz 30 kW variable power microwave oven and dielectric heating studies were performed. A comparison of the theoretical heating characteristics and the results from actual dielectric heating studies was conducted to evaluate the dielectric property measurements on each mineral. This report presents the results of the Bureau's research in identifying the dielectric properties of low-loss minerals according to the mineralogical classification scheme along with their irradiation studies. Though far from complete, this study represents some of the more frequently encountered low-loss minerals.

Jan 1, 1988

By R. L. Beatty

IN INDUSTRIAL and domestic daily life carbon monoxide is the most frequently encountered toxic gas. hazardous concentrations of carbon monoxide may be present in the vicinity of many industrial operations, such as metallurgical processes, coke ovens, and fuel- and synthesis-gas producers, and may be encountered in confined spaces, such as dwellings, garages, workshops, vehicular tunnels, and mining operations, in connection with the use of heaters, boilers, internal-combustion engines, after blasting operations, and after fires and explosions. Evaluation and control of the health and safety hazard caused by carbon monoxide depend primarily on the analytical detection of the presence of carbon monoxide and determination of its concentration in air and in various gaseous mixtures. The choice of method of analysis in any particular situation depends on such factors as required accuracy, range of concentration involved, convenience, speed of analysis required, quantity of sample available, qualitative composition of sample or atmosphere to be analyzed, and possible effects of interfering gases. Some of the methods described require only adequate understanding of operational techniques, whereas others require thorough appreciation and skill in applying the principles involved. The instruments and analytical procedures commonly used for detecting and determining carbon monoxide are described in detail, and reference is made to more specialized methods:

Jan 1, 1955

By R. L. Soderberg

This paper is one of a series on mining methods and costs being published by the Bureau of Mines. It describes briefly the mining methods employed since the start of operations in 1937, with emphasis on the diamond-drill blast-hole method of ore breaking and slusher-drift method of ore drawing at the Holden mine of the Howe Sound Co., Chelan Division, Holden, Wash. The Holden mine is in the north-central part of the Cascade Range, 11 miles up Railroad Creek from Lake Chelan. The nearest railroad is at Chelan Falls, 40 miles by boat and 4 miles by highway from the mine. All freight comes into the mine and all concentrates are shipped out via Chelan Falls. The altitude of the main haulage level is 3,500 feet. Railroad Creek Valley is covered with a dense growth of fir and spruce, while most of the surrounding mountains are rocky, with sparse timber growth.

Jun 1, 1948

By G. R. Hopkins

Although many small refineries were dismantled in 1934 the total number of plants, including a few under construction, increased from 604 at the beginning of the year to a new high of 638 on January 1, 1935. The capacity also reached a new record, the total of 4,072,400 barrels of crude oil daily being about 45,000 barrels higher than the previous high of January 1, 1932. The number of refineries increased materially in 1933, following construction in east Texas and the building of many small plants in the Rocky Mountain district and elsewhere. Most of the new plants of 1933 were built to provide an outlet for crude or because the ratio between crude oil and gasoline prices appeared conducive to profits However, low gasoline prices and increased costs in 1934 dispelled the hopes for profits; many plants were shut down, and some were dismantled. The number of operating plants declined from 454 on January 1, 1934, to 435 on January 1, 1935, but the number of inactive plants increased from 137 to a new high of 196 during the same period. As indicated above, new construction was at a minimum in 1934, and on January 1, 1935, only 7 plants were being built.

Jan 1, 1935

By A. C. Fieldner

Much activity is called for in the present period of hightened national effort, and wise direction of such a program must always be conditioned by positive knowledge gained in years of slow and painstaking study and development. Research and technologic investigations on coal by the Bureau of Mines have been described in a series of annual

Jan 1, 1941

By Allen S. Smith

Analysis of the helium content of a natural gas presents more than the usual difficulties encountered in applying the thermal--conductivity method because of the relatively small amounts of this inert gas present and the wide variation in the other constituents. However, the numerous advantages of this method and its adaptability to continuously recording and control instruments make it worthy of consideration. A specific application of the method described yields quantitative results only when used with gas mixtures of known qualitative compositions which vary within predetermined limits. Periodic analyses for the helium content of a producing gas well may be conveniently made by an absorption method3/ and a continuous analytical method is not necessary for this purpose. Natural gas containing 1.75 to 1.90 percent of helium produced from Government-owned wells is processed in the Amarillo (Texas) Helium Plant of the Bureau of Mines. The helium extracted in the plant is supplied to the Army and Navy, and the processed natural gas is sold to a commercial gas company4/. As complete recovery of the helium in the raw material is not economically practicable, the processed gas contains 0.1 to 0.3 percent of helium, depending upon conditions of operation;- Production is checked against the helium removed from the gas, which before the installation of the thermal--conductivity apparatus was calculated from the analysis of a cumulative sample of the processed gas. As conditions of operation affect the residual helium content to a large extent, a composite sample was an uncertain index of the efficiency of the process.

Jan 1, 1934

By Richard J. Kline

The underground mining industry is presently using the fluid network analyzer and digital computer to analyze ventilation systems. The availability of the digital computer and ventilation programs to mining companies has escalated its use, permitting the design and modification of new or existing mine ventilation systems to be projected completely and thoroughly with consistent precision. Because the analog computer has been analyzing ventilation systems accurately for many years, a comparison of the analog and digital methods was warranted. This report summarizes a detailed comparison for one mine, based on parallel analyses by the two computer systems.

Jan 1, 1972

By Christopher C. Jobes

This U.S. Bureau of Mines report describes a system to determine the position and heading of a mining machine during maneuvers in the face area of an operating mine section. The system is the first step in the development of a guidance system for automated mining machines. The position and heading algorithm is described, and a preliminary error analysis is performed. The sensors employed were linear position transducers mounted on a mining machine with their cables attached to points on a stationary reference. Four linear position transducers were used to provide a data redundancy that increased the reliability of the guidance system. The linear position information obtained from the transducers was processed mathematically via the position and heading algorithm to provide the desired position and heading information. The algorithm takes advantage of sensor redundancy to continually test the accuracy of the sensor data. The major sources of error were determined to be the linear position transducers, the analog-to-digital (A/D) converter used to interpret the data, and the sampling frequency of the measurement system. These sources of error were evaluated to determine their inaccuracies for use in calculating the overall system accuracy.

Jan 1, 1990

By C. T. Anderson

In July 1947, the U. S. Bureau of Mines, in cooperation with the Air Materiel Command, started an investigation of zirconium alloys with the object of determining the suitability of such alloys for high-temperature applications. This report covers the preliminary study of about 25 zirconium-rich alloy systems with respect to preparation, fabrication, tensile properties, metallographic structures; constitution, and heat resistance. Obviously, each system could not be investigated thoroughly, and this publication can be regarded only as a first approach. The more promising individual alloy systems will be studied in greater detail and reported in subsequent publications. The study of zirconium alloys on such a scale has been made possible by the U.S. Bureau of Mines developments in the past 5 years On producing zirconium metal. This basic process is similar to that developed by Kroll for producing ductile titanium metal and consists essentially of reducing zirconium chloride by means of molten magnesium. The Northwest Electrodevelopment Laboratory at Albany, Oreg., has produced several thousand pounds of ductile metal in this manner and has a pilot plant producing over 300 pounds of metal per week. Alloys were prepared by melting Bureau of Mines zirconium and the best available grade of alloying element in graphite, with suitable provisions for preventing oxidation. The ingots were quartered longitudinally and sheath-swaged at 850° c. to 3/8-inch diameter rod. Two of those rods were send to Wright Field for room-temperature and 1,200° F. tensile properties. The remaining two sections were used for metallographic, hardness, heat-treatment, and heat-resistance studies. The salient features of this investigation are summarized in table 1.

Jan 1, 1950

By James A. Wasson

The Mitchell and Berea sands were cored and logged in Fred Link well K-l, Lower Newport field, Washington County, Ohio. Core and reservoir fluid analyses and available field data were studied to determine if these sands could be successfully waterflooded. The results of the study indicate that there is insufficient oil in place to form an oilbank in either the western Mitchell pool or the Berea sand, and that no commercial recovery of oil by waterflooding can be obtained in these reservoirs.

Jan 1, 1967

By M. Carrales, C. J. Jirik, W. D. Dietzman

In view of the developments and recent interest in recovering heavy oil , this report was prepared to present general information on more than 2,000 heavy oil reservoirs in more than 1,500 fields in 26 states . Information given on each heavy - oil deposit includes the following items : Field and formation , location , average or range of depth , average API gravity of oil , average thickness of formation , areal extent of field , total productive wells drilled in field , discovery date of field , field status in 1963 , cumulative production to Jan. 1 , 1964 , and all known types of secondary - recovery operations initiated ( active and terminated ) in the reservoirs . The geographical location of heavy oil accumulations in the United States is shown by a map , and a brief discussion of 14 different areas is given in the text . As of Jan. 1 , 1964 , 75 percent of the heavy oil reservoirs in the United States had produced more than 10 billion barrels of oil and are estimated to contain over 90 billion barrels of oil in place . It is also estimated that if the deposits which have had little or no production history , such as the one in Missouri , were included , the total remaining heavy oil in place would be in excess of 150 billion barrels . To find economical ways of recovering this vast reserve of heavy oil , industry is developing technology in several types of thermal - recovery methods . Some of the general considerations and more suitable limitations in selecting a prospect to study for thermal - recovery techniques are : Lithology , depth , viscosity of reservoir fluids , gravity of oil , reservoir thickness , oil in place , and permeability and porosity .

Jan 1, 1965

By W. H. Coghill

Numerous investigators have studied grinding. Each has contributed his bit to a literature that is difficult to correlate. Too many of the results have been transformed into curves with so many "inflection points" and "counterflexures" that they obscure the issue. Some of the investigators have neglected the very essence of the problem, namely the power and the amount of material to which a known amount of work was applied. The purpose of this paper is to show the ease with which results can be interpreted when these quantities are duly recognized. Some grinding tests will be given for illustration. Grinding studies are of two kinds: (1) Study of the character of the ore and (2) study of the performance of the machines. Several ores may be crushed by a given machine, or several machines may be used on a given ore. The illustrations given in this report cover both objectives.

Jan 1, 1934

By L. O. Bacon

This Bureau of Mines report summarizes the results of laboratory work in the design of instrumentation for obtaining the dynamic tensile strength of rock at minimum loading. Minimum loading is defined as the lowest tensile loading by pulse reflection to cause fracturing. The instrumentation for obtaining dynamic tensile strengths of rock cores evolved into the use of a compressed-air pellet gun to impact one end of a rock core, suspended by wires, at increasing increments of air pressure. Maximum strain was measured on most or all of the impacts, and the strain at fracture of the core was obtained by extrapolating the pellet velocity-strain curve to the pellet velocity at fracture. Stress at tensile fracture was obtained from the maximum s train, and the dynamic Young's modulus was calculated from the rod velocity by using simple rod theory.

Jan 1, 1962

By George H. Holmes

The water situation in Nevada mineral and related industries is described in this report. It contains information on the sources and adequacy of supply to current operators, requirements and uses, quality and costs, geography, hydrography, precipitation and evaporation characteristics, and Nevada water laws. Also, information is given on the water requirements of one public utility powerplant, and the source and consumption of water in four major cities. Water distribution at 24 operations is shown on schematic waterflow diagrams. The mineral industries of Nevada in 1962 used 8.6 billion gallons of new' water and reused 3.8 billion gallons for a total usage of 12.4 billion gallons. The copper industry was the major water user. The 1962 value of all mineral production in Nevada was $85.5 million. The large amount of water required to maintain thin high production is obtained principally from ground-water sources in alluvial valleys and the permeable rock formations of some mountain ranges. Some water is also obtained from perennial streams and springs. Sources of water utilized by existing industry ire near most mineral industry operations; however, seven companies are forced to pipe water distances ranging from 2 to 8 miles. Although water supplies of presently operating companies are adequate at most operations, several companies resort to large-scale reuse of water as a matter of conservation and economics. Acquisition of water by new operators is possible but takes considerable negotiation. Water rights, surface and underground, are controlled by the State. The quality of the water is satisfactory for most purposes. Analyses of 19 samples, listed in the appendix, show the range in water quality at various plants throughout the State. Costs of delivering new water to current operations range from 2 to 26 cents per 1,000 gallons with an average of 10 cents per 1,000 gallons for power and maintenance. No firm costs for recirculating water were available; estimated costs range from 1.5 to 2.5 cents per 1,000 gallons. The mineral-product value of the entire Nevada mineral industry in 1962 was equivalent to $10 per 1,000 gallons of new water and $26 per 1,000 gallons consumed. Projection of the 1962 water requirements of the Nevada mineral industry indicates that the demand For new water will increase from 8.6 billion gallons in 1962 to 11.9 billion gallons in 1980, a 43-percent increase. Water requirements in the year 2000 are estimated as 14.8 billion gallons, an increase over 1962 water demand of 78-percent.

Jan 1, 1966

By Richard L. Fischer

Constant-volume charges of precipitated PETN (pentaeythrite tetranitrate) at three specific gravities (0.50, 1.00, and 1.50) were used in laboratory tests to examine the effects of changes in explosive properties on free-surface displacement pulses and on crater dimensions. The tests were performed in large blocks of cement-mortar. The values for the detonation velocity, detonation pressure, specific energy, energy density, and energy release rate were calculated from the explosive loading density. Calculated explosive properties were correlated with free-surface displacement pulse measurements, strain energy, and measured crater dimensions. Increases in explosive properties resulted in increased free-surface displacement pulse parameters and crater dimensions. The loading density, detonation velocity, energy density, detonation pressure, and energy release rate were found to be best indicators of explosive performance. Simple acoustic relationships involving impedance ratios were examined and could not be used to predict peak displacement amplitude or strain energy. Data are presented in the customary English units as well as the International System of Units (SI).

Jan 1, 1970

By R. K. Koch

The normal spectral emissivities of liquid Ti, V, Zr, Mo, and Pt were determined at the fusion temperatures in an electron-beam furnace using a water-cooled copper hearth. The normal spectral emissivities were estimated above the melting points by using adjusted two-color temperatures as approximations of the true temperatures for substitution in Wien's equation. Simultaneous brightness temperatures were determined with a micro-optical pyrometer. The true temperature ranges covered were 1,668° to 1,885° C for Ti; 1,919° to 2,013° C for V; 1,855° to 2,367° C for Zr; 2,610° to 2,751° C for Mo, and 1,772° to 1,990° C for Pt. The spectral emissivities for titanium and zirconium decreased with increasing temperature. At an effective wavelength (?) of 658 mµ the emissivity of titanium ranged from 0.51 to 0.45 and zirconium, from 0.47 to 0.41. The emissivities of vanadium (? = 658 mµ) and molybdenum (? = 657 mµ) were constant at 0.41±0.02 and 0.33±0.01, respectively. The spectral emissivity of platinum (? = 658 mµ) was constant at 0.39±0.02 up to 1,900° C; above that temperature anomalous data were obtained. A mass spectrometric study indicated that platinum was reacting with back-streaming silicon vapors from the diffusion pump when the ambient pressure was greater than 2 X 10-5 torr.

Jan 1, 1973

By C. C. Hwang

The Bureau of Mines made time-dependent calculations to determine the size of a stationary source fire within a ventilated duct (or passage-way) necessary to ignite a combustible duct liner. The objective of this work was to gain more understanding of what occurs in duct fires and to determine critical conditions for ignition and propagation of mine fires. Heat transfer to the combustible surface includes both convective and radiated components, while the heat is conducted into the combustible and reradiated to the surroundings. The combustible is assumed to ignite when the net heat transfer to its surface is sufficient to raise the surface temperature to some minimum temperature, defined as the ignition temperature. A nondimensional parameter, which characterizes the source-fire intensity in the presence of ventilation flow, emerges as a parameter for a criterion of the critical conditions. The results of these calculations indicated that the minimum fire size necessary for ignition increases with the ventilation rate and duct cross section. These results are compared with experimental results obtained from fires in a 0.8-by 0.8-by Il-m-long duct and a full-scale gallery (2.4-by 2.4-by 65-m). Agreement between the theory and the experiment is good.

Jan 1, 1988