Search Documents

By Robert E. Barieau

General expressions for evaluating practically all the thermodynamic properties of a fluid from a single equation of state are derived. Most of the formulas are expressed in terms of the compressibility factor, with this factor being an explicit function of the temperature and the molal density. Similar expressions are given using reduced variables.

Jan 1, 1967

By E. W. Felegy

Since 1920, the Bureau of Mines and, other agencies have conducted numerous investigations of methods of communication for use in mines in times of disaster or emergency. The results of these investigations have been reported in various publications (3, 4; 5, 6, 8, 9, 10, 11, 12, 13, 14, 15, 16). In November 1944, the Bureau of Mines resumed the study of emergency underground communications. Until March 1946, the program was directed toward reexamining methods of underground communication that indicated possibilities of success. Since April 1946, the principal interest of this investigation has been in methods of application of radio to communication in mines, low-frequency radio seeming to offer the most promise as a successful method of emergency mine communication. Results achieved in reexamining other methods and in the investigation or the application of low-frequency radio between November 1944 and September 1946 were reported previously in a publication entitled "Some Studies on Emergency Mine Communications".

Jan 1, 1948

By G. J. Conroy

Cable whip occurring during normal movement of a shuttle car can result in a personnel hazard and excessive tensions in the cable. This Bureau of Mines report discusses preferred payout and reel-in torque settings to reduce cable whip. A simplified adjustment procedure is described.

Jan 1, 1974

By R. A. Cortese

The U.S. Bureau of Mines has developed a flame-radiation-powered trigger device to explosively activate suppression barriers to quench gas and coal dust explosions. The major component of the device is a silicon solar panel, which converts radiation from the developing explosion into electrical energy to initiate an electric detonator, which releases an extinguishing agent into the advancing flame front. Solar panels that are rated to produce 20 W of electrical power when exposed to the sunlight are producing about 200 W when exposed to a full-scale dust explosion. The solar panel is electrically isolated from the detonator by a pressure-sensitive switch until the arrival of the precursor pressure pulse, which always precedes a deflagration. This combination of pressure arming and flame-powered photogenerator prevents false barrier activation and requires no external power supply.

Jan 1, 2010

By J. S. Dunning

The objective of this research by the U.S. Bureau of Mines was to determine the effects of AI additions on the sulfidation resistance of Fe-Cr-Ni alloys. A series of Fe-Cr-Ni alloys with and without -additions of 4 pet AI were tested in a wet S vapor atmosphere at 677 C. A study of the morphology and composition of corrosion scales indicated a different corrosion mechanism for AI-free alloys compared with AI-containing alloys. Aluminum-containing alloys formed a compact, tightly adherent layer at the metal-scale interface that reduced corrosion rates by a factor of 3 to 10 compared with that of AI-free alloys. The thin, adherent AI-containing scale limited inward diffusion of 0 and S to the base metal and outward diffusion of Ni from the base metal. Aluminum-containing alloys formed a three-layer scale in oxidizing-S environments, while AI-free alloys formed a less protective two-layer scale.

Jan 1, 1989

By George S. Rice

"It is well known that the lost coal left in the ground in mining, under such conditions that recovery is practically impossible, constitutes a large proportion of the coal in the beds worked. A recent estimate, in a paper on ""The World's Fuel Supply"" presented by Prof. L. P. Breckinridge, of Yale University, before the Annual Meeting of the. American Society of Mechanical Engineers, places the average loss in bituminous coal mining as one-third left in the ground.The bald statement that there is a loss of one ton of coal for every two recovered may seem to those not familiar with coal mining to imply inexcusable and wanton waste. Perhaps a better way of expression is in terms of total recovery rather than in terms of losses. Many mine superintendents and mine owners will readily concede that their total recovery may be only 60 to 75 per cent, but to state that they are wasting 25 to 40 per cent arouses antagonism. The suggestion is of willful waste, whereas the majority of the operators try to the best of their ability to get a high recovery under the adverse and complex conditions that confront them. These involve natural, commercial, and labor conditions, and the requirement in many cases of boundary pillars under railroads and buildings, which may be called for in the deed or lease, or in the absence of specific exemption in the deed or lease, the common law requirement that a surface owner is entitled to the support of the surface."

Apr 1, 1921

By E. D. Regad, W. E. Wallace, P. S. Mike, C. A. Hill, V. Vallyathan, M. J. Keane

"Respirable-sized quartz, a well-established fibrogenic mineral dust, is compared with kaolin in erythrocyte hemolysis assays aher treatment with saline dispersion of dipalmitoyl phosphatidylcholine, a primary phospholipid component of pulmonary surfactant. Both dusts are rendered inactive after treatment, but the membranolytic activity is partly to fully restored aher treatment with phospholipase Ai. an enzyme normally associated with cellular plasma membranes and lysosomes. Phospholipid-coated dusts were incubated for periods of 2-72 h at a series of applied enzyme concentrations, and the adsorbed lipid species and hemolytic activity were quantitated at each time for both dusts. Surfactant was lost more readily from quartz than from kaolin, with consequent more rapid restoration of mineral surface hemolytic activity for quartz. Interactions of surfactant and mineral surface functional groups responsible for the mineral-specific rate differences, and implications for determining the mineral surface bioavailability of silica and silicate dusts, are discussed. INTRODUCTIONMineral particles depositing in the lung acinus will contact an aqueous coating containing surfactant molecules spread on the air-liquid interface and dispersed within this hypophase; the primary components of that surfactant are diacyl lecithin phospholipids (King and Clements, 1972; King, 1982). Adsorption of this surfactant can suppress the cytotoxicity of mineral dusts (Marks, 1957). Suppression of hemolytic activity, a measure of membranolytic potential and an indicator of bioavailability of the mineral surface, of respirable-sized quartz and kaolin clay dusts with the adsorption of dipalmitoyl glycerophosphorylcholine or dipalmitoyl lecithin (DPL) has been measured (Wallace et al., 1985). Such contact and adsorption of pulmonary surfactant in vivo may provide a first defense system of the lung against respired dusts."

Mar 1, 1992

By L. A. Readdy

Pilot Hole "X" was drilled to test the formations through which the ventilation shaft for the proposed U.S.B.M. demonstration oil shale mine would be drilled. The geologic formations encountered in this hole are discussed. Correlation of the geologic horizons encountered in this hole with those encountered in nearby drill holes was accomplished by the use of geophysical logs. Data on the geophysical interpretations are provided. The anticipated geotechnical characteristics of the geologic units encountered in Pilot Hole "X" are described.

Jan 1, 1977

By Ernest W. Johnson

In most underground iron mines in the Lake Superior district the active workings are at considerable depth. When additional openings into such. nines are needed, operating officials are eager to discover more efficient methods of constructing them. In recent years, openings into two mines in the district were made by the borehole method,-which employs chilled-iron shot as the cutting medium. Others were made by the churn-drill method, in which pilot hole is churn-drilled and subsequently reamed to a desired but relatively small diameter. Both methods are comparatively new and unique, at least in some phases and in their application.

Jan 1, 1946

By F. H. Nehl

Ion elutriation was used to extract silver cyanide complexes and free cyanide from aqueous streams containing up to 10 ppm silver and 5 ppm free cyanide. Screening tests selected nine of 350 different surfactants for further, larger scale experiments. The screening procedure used 0.1 g of each of the surfactants in 300 mL of synthetic wastewater. Air was sparged into the test cell at 50 cc/min. The foam was refluxed during the tests and was not sampled. Samples of the solution were taken at specified intervals and analyzed by wet chemical methods for free cyanide and by atomic absorption for silver content. The most effective surfactants lowered the silver and free cyanide concentrations to less than 0.5 ppm in 1 h or less. These surfactants were quaternary amine salts with one long chain (C12-C18) organic group and three methyl groups. Experiments using 3 L batches of wastewater or an ion elutriation cell continuously fed with solution draining from an inactive heap leach operation confirmed the results from the screening tests.

Jan 1, 2010

By B. J. Moore

This publication contains analyses and related source data for 352 natural gas samples from wells and pipelines in 18 States and 5 foreign countries. All of the samples were obtained and analyzed during calendar year 1974 as a part of Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economics. This survey has been conducted in the United States by the Bureau of Mines since 1917. In late 1965, the survey was expanded to include foreign gasfields. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4862 and 576.3 The results of the investigation of the occurrences of helium are published annually to make the information available as soon as possible to the gas industry and the public in general. Sixteen previous publications have presented the results of 10,479 gas analyses prior to 1974. The first three, Bulletins 486,4 576,5 and 617,6 contain analyses and related source data on

Jan 1, 1975

By Harold L. Gibbs

The purpose of this paper is to encourage petrographers to prepare thin sections, as the demand for microscopic examination of rocks, ores, and metallurgical products is becoming more general in .the mining metallurgical-fields. This paper has been written with the knowledge that the successful thin-section methods and the several new techniques herein described will be helpful to all engaged in this field of work. Detailed instructions for making thin sections by methods developed at the Salt Lake-City laboratory of the Bureau of' Mines are given in this paper. Several new techniques are described for making thin sections of loose grains and fine sands and for making good thin sections of highly altered and friable rocks. The methods described insure superior bonding of the rock to the glass slide, thus virtually eliminating any failures due to parting of the section from the glass slide, and permit fast mounting, grinding, and finishing, thereby materially lessening the time required to prepare thin sections.

Jan 1, 1950

"SUMMARYThe K.M.A. reservoir was discovered to be oil bearing at a depth of 3,719 feet on March 11, 1931. Extensive development, however, was not begun immediately, because the discovery well had a low initial daily oil production, and market conditions for oil were unfavorable. Development of the field progressed slowly for the next 6 1/2 years. In the latter part of 1937, a wildcat well approximately 2 miles southwest of the discovery well was drilled on a magnetometer high and completed with an initial flowing production of 2,016 barrels of 43° A.P.I.-gravity oil in 12 hours. Rapid development of the southwestern part of the K.M.A. field was begun immediately and continued until over 700 wells were drilled and approximately 12,500 acres proved oil productive.Because of the large size of the entire K.M.A. field, this report is limited in scope to the southwestern part only, and the discussion that follows pertains to this area only. The closing date for production statistics is August 1, 1949.The K.M.A. structure is a complex anticline having a maximum closure of 250 feet, and the K.M.A. formation is composed of sediments that grade from limestone through sandy lime and limy sand to sandstone with thin streaks of shale. Two distinct members of the K.M.A. formation, zone I and zone II, are oil productive. Core analyses indicate the average porosity to be 16.5 percent for zone I and 16.1 percent for zone II. A relationship was established from core data, which showed the correlative permeabilities to be 42.1 millidarcys for zone I and 39.5 millidarcys for zone II, whereas the arithmetical averages of the permeabilities were 84 millidarcys for zone I and 216 millidarcys for zone II. Connate water saturations were 17.5 percent for zone I and 20.0 percent for zone II. The porosity-saturation method, using a thickness-correction factor, was employed to calculate the volume c 168.1 million barrels of stock-tank oil initially in place in the reservoir. Analyses of the reservoir oilIn that, although the initial reservoir pressure was 1,750 p.s.i., the original reservoir oil was saturated to only 1,300 at which pressure 1 barrel of stock,tank oil contained 525 cubic feet of gas in solution.A serious decline in reservoir pressure during the 2 years of rapid development alarmed the operators and caused them to consider a cooperative pressure-maintenance program. In the latter part of 1939, the K.M.A. Pressure Maintenance Association was organized, and the gasoline plants in the field agreed to process the wet gas and return the dry gas to leases having gas-injection wells. Approximately 27 percent of the cumulative volume of produced gas had been returned to the reservoir by August 1, 1949."

Jun 1, 1952

By L. Kaufman

A range of processing conditions and compositions have been evaluated in order to optimize the properties of TiB2-(Ni,Cu) composites for application as a non-sparking tool material for use in coal mining operations. Fifty billets containing from 70 to 9S weight percent titanium diboride were hot pressed at 3000 psi between 2400°F and 2650°F. Samples which were cut from these billets were used to measure hardness, bend strength and impact strength so that composition/processing optimization could be effected. Eight compositions selected on this basis were evaluated by incendivity tests in order to choose the best composition. The best results were obtained for an 85 w/o TiB2-12 w/o Cu-3 w/o Ni composite hot pressed at 2650°F and 3000 psi. This material appears to be the best choice for fabrication of coal cutter bits to be evaluated in field tests.

Jan 1, 1973

By T. A. Klinefelter

"INTRODUCTION During the development work on sponge iron by the Bureau of lines it was desired to produce a product of maximum density for the furnace. One means of doing this would be to make a plastic mixture of the ground ore and extrude as pellets or large slugs or brick shapes.If a pelletizing Process is employed, the pellets must be strong enough to resist breaking when rolled and tumbled in going through the rotary kiln. If a brick-making process is employed, the brick must be strong enough to withstand handling and considerable pressure when stacked in the kilns.The study had two objectives: first, to find a binder of sufficient strength throughout the early stages of curing and heat treating and, second, to determine the degree of curing and heat treatment necessary to prevent disintegration under normal working conditions.Although the investigation had as its primary objective the processing of sponge iron, the data should interest other industries in which non plastic or poor-bonding slimes are a problem."

Jan 1, 1946

By Ronald H. Church

The Bureau of Mines tested & ground penetrating radar (GPR) system in the central Florida phosphate district. to determine the feasibility of utilizing GPR technology for subsurface cavity detection. The test area is located in karst topography where sinkhole development is prevalent. State regulations require subsurface drilling of damsites to identify underground anomalies; however, this method is not totally accurate in locating subsurface cavities that could lead to sinkhole development. An electromagnetic method of identifying anoma-lous subsurface conditions could reduce or eliminate the possibility of dam failure due to sinkhole development. The Bureau devised a GPR system that successfully penetrated over 50 ft of overburden and gave recognizable radar return signals characteristic of a rock-cavity interface.

Jan 1, 1986

By Laurence G. Trudell

Geology and oil-yield data are presented for a 58-square-mile area encompassing the U.S. Department of the Interior oil-shale leasing program tracts in the western Washakie Basin, Sweetwater County, Wyo. Lithology and oil yields of samples from three Bureau of Mines coreholes are evaluated and correlated with Kinney Rim surface sections measured and sampled by the U.S. Geological Survey. Minable sections of oil shale averaging up to 25 gallons of oil per ton crop out on Kinney Rim in the Laney Member of the Green River Formation. Thick oil-shale sections in the Laney Member that average 15 gallons per ton represent 155 million barrels of oil in place per square mile. In the lower part of the Green River Formation the Tipton Shale Member contains a 20-to 40-foot section averaging 15 gallons per ton. Beds of high-volatile C bituminous coal up to 6 feet thick are present in intertongued parts of the lower Green River Formation and upper Wasatch Formation.

Jan 1, 1973

By M. J. Ankeny

This is a study of 58 fatal haulage accidents investigated by Federal coal-mine inspectors during the period January - June 1951. The information presented in this circular was obtained by analyzing fatal haulage accidents in 33 bituminous-coal producing counties representing 11 States. The physical conditions represent a cross section off producing coal beds. Mining and transportation methods vary, from those of small hand-loading mines to those of large modern mechanized operations. These data are thought to be representative of haulage conditions within the bituminous-coal mining industry and are submitted to follow up the Information Circular 7604 ?Analysis of Haulage Fatalities in Bituminous-Coal Mines - 1950.? Coal-mine haulage ranks second as a cause of coal-mine fatalities, and the problem of haulage safety is complex. It is subject to constant change and is comprised of numerous influencing variables, which are not always obvious. The solution to this problem will not come through the application of any standard formula or mechanical approach since the inherent factors are strongly influenced by the human equation, and the chain of circumstances is further affected by expediency.

Jan 1, 1951

By J. E. Cleveland

The major health concern for uranium miners is the release of radon gas and the resultant ingrowth of the short lived daughters in the mine atmosphere. Present methods of control are the utilization of mine ventilation systems for dilution and control of ingrowth time to maintain working levels below those set by regulations. This study examined pressure cycling efforts on the radon emanation. The mechanical ventilation systems were altered to allow pressure changes throughout the mine to increase radon influx during the off shifts and thus deplete the sources of radon gas. Continuous radon working level and environmental monitors, developed by the Bureau of Mines, were employed to monitor radiation and physical parameters in the mine workings. The mine ventilation system was then varied to induce radon flows during off shifts, thus, depleting the radon sources during normal production shifts. Electro-static precipitators were also tested to determine radon daughter collection efficiencies. Both radon and radon daughter concentrations were monitored and evaluated. Major problems were found in the simple mechanical operation of cleaning these units.

Jan 1, 1982

By A. Landsberg

Kaolinitic clays are potentially a vast domestic resource for aluminum. Utilization of this resource could decrease or eliminate the nearly complete dependence of the United States on foreign raw materials for this important metal. Furthermore, processing of clay to aluminum through anhydrous chloride metallurgy could reduce the high electrical energy requirements of the conventional Hall-Heroult aluminum reduction process. Several anhydrous chloride processes have been proposed; however, unresolved technical problems have prevented their commercialization. In particular, an acceptable chemical means has not been found to extract aluminum from clay as a highly pure anhydrous aluminum chloride. This Bureau of Mines report identifies and discusses the important chemical problems involved in achieving an acceptably rapid, self-heating, selective chlorination reaction and the subsequent separation of iron chloride byproduct from the anhydrous aluminum chloride.

Jan 1, 1983