Search Documents

By R. V. Higgins

Many contributions to methods of forecasting the performance of waterfloods of a five-spot pattern have been made by investigators. In most of these forecasting methods, a previously selected sweep efficiency is used, and other simplifying assumptions are employed to obtain the objective. In this paper the calculated oil recoveries from several five-spot single- and multiple-layer stratified reservoirs were made with a minimum of assumptions, and because of the techniques used, no previously selected sweep efficiency was required. As a result, the accuracy of the forecast is increased. Permeability curves and continuously changing saturation gradients are used in every section of the pattern. By means of a potentiometric model, the flood pattern is divided into channels, the centers of which are the streamlines. The channels are divided into cells. As flood water enters, the permeability and saturation of each cell change with time. In this study the production from multiple-sand layers of different absolute permeability but with the same relative permeability-saturation relations are combined. The results are shown for a single- and 10-layer reservoir with a permeability variation of 0.60. The oil rate, water-oil ratio, and recovery are shown as functions of time for a 2- and 20-centipoise oil starting in primary phase and after fill-up.

Jan 1, 1962

By H. W. Wainwright

.1. The purification pilot plant and the equipment, solution, and gas cycle used for removing hydrogen sulfide and carbon dioxide are described. 2. As sulfur recovery is necessary in any large Fischer-Tropsch plant, pilot-plant runs were made at 300 p.s.i.g. to study the efficiency of tri-ethanolamine solutions in removing selectively hydrogen sulfide from gases containing varying amounts of carbon dioxide. 3. Aqueous solutions of TEA of 20, 30; 35, and 50 percent were investi¬gated. Data indicate that 30 to 35 percent is the optimum concentration if both selectivity and economy are considered. Slightly better selectivity is obtained with the.20 percent solution, but steam consumption is greater owing to the higher solution rates. Results from our pilot plant runs indicate that a 50 percent solution not only produces an acid gas of lower hydrogen sulfide content but also requires high solution rates to effect hydrogen sulfide purification. 4. Data from 37 runs using TEA are presented in tabular form. In addition, the data are correlated and presented in three sets of curves. By using these curves, it is possible to calculate the compositions of the purified and acid gases for various raw gas mixtures. 5. In cooperation with the Southern Natural Gas Co., investigations were carried out at 300 p.s.i.g. on the simultaneous removal of hydrogen sulfide and carbon dioxide, from gases using various concentrations of diethanolamine. 6. Data from 17 runs employing 20, 30, and 40 percent DEA are reported in both tabular and graphic form. 7. A comparison of the data from one DEA run made at 200 p.s.i.g. with those from the runs operating at 30O p.s.i.g. shows float the absorption capacity of the solution, and, hence, the steam requirements per gallon are about the sage for both pressures. .The only real advantage of the higher pressure is the additional volume of gas that can be treated. 8. The quantity of steam needed to reactivate fouled TEA and DEA solutions increased as the reactivator pressure was increased about 1,0 to 1.1 pounds of steam was required for each gallon of circulating solution when the reactivator was operated at 5 p.s.i.g. 9. A curve is included that shows the effect of the hydrogen sulfide con-centration in a lean 35 percent TEA solution on the hydrogen sulfide content of the purified gas and on steam consumption for reactivation. 10. Both TEA and DEA reduced the organic sulfur content of the raw synthesis gas considerably. Analyses of the lean amine solutions showed a gradual build up of sulfur compounds, indicating that the compounds formed by the amines and organic sulfur do not break down under the ordinary operating conditions of the reactivator. 11. Considerable operating difficulty was encountered in the pilot plant owing to foaming of the amine solutions. Laboratory experiments in which the effectiveness of certain antifoam agents was studied showed Alkaterge C to be most promising for the particular conditions studied.

Jan 1, 1952

By L. G. Marshall

This report presents a cross section of the sand and gravel operations in the Minneapolis-St. Paul area. The study covers individual operations, economic problems peculiar to the industry, glacial geology of the area and its effect upon the grades and types of products, and past, present, and future trends of the expanding population and its effect upon the industry.

Jan 1, 1963

By L. G. Marshall

This report presents a cross section of the sand and gravel operations in the Minneapolis-St. Paul area. The study covers individual operations, economic problems peculiar to the industry, glacial geology of the area and its effect upon the grades and types of products, and past, present, and future trends of the expanding population and its effect upon the industry.

Jan 1, 1963

By Clarence Hall, S. P. Howell, W. O. SNELLING

The explosives used in coal mines not only occasion accidents such as occur in the use of explosives elsewhere, but they frequently cause widespread disasters by igniting explosive mixtures of mine gas and air and of coal dust and air, or both. In addition, the firing of ex- plosives so shakes the walls and roofs of the mines as to cause falls, with their attendant casualities. Considering the large number of explosives and their wide range in composition and properties, it is obvious that certain of them should prove more suitable for use in coal mines than others. The problem is to determine which explosives are the most suitable for this purpose and the precise conditions under which they may be used with the greatest safety. Of course this problem could be worked out in actual mining, but experimental investigations when accompanying commercial opera- tions are hazardous and slow. To obtain the information sought, in the speediest and most economical manner, laboratory methods must be resorted to. The adoption of such methods began about 30 years ago with experiments in an iron gallery mounted on wheels, at Zwickau, Germany. This laboratory method of attacking the prob- lem has so commended itself that it has not only been repeated else- where in Germany but has at intervals been officially adopted, with many modifications and additions, by the Governments of Belgium, Austria, France, and Great Britain. Such was the status of coal-mine investigations in Europe when in 1904, an organization in the Geological Survey, which in 1907 be- came the technologic branch, was created to investigate the mineral- fuel resources of this country. At that time no division of the Na- tional Government had official cognizance of conditions existing in our mines, but through its system of collecting fuels for tests the technologic branch was forced to recognize that coal-mine accidents are a factor that must be reckoned with in determining the extent and availability of our mineral-fuel resources. This became so apparent, and it was so obviously a function of this branch to make a systematic research as to the cause and prevention of such acci- dents, that in July, 1907, experts were appointed especially to deal with this problem. As a result, not only was Bulletin 333, on Coal- Mine Accidents: Their Causes and Prevention, prepared and pub- lished, but through personal inspection of foreign testing stations, and a study of their reports and the critiques of their methods and operations, definite plans for the establishment of such a testing station in this country were formulated. In the latter part of 1907, four grave disasters occurred in close succession consequent on explosions in the Monongah mines in West Virginia, where 368 men were killed, the Darr mine in Pennsyl- vania, where 160 were killed, the Naomi mine in Pennsylvania, where 34 were killed, and the Yolande mine in Alabama, where 61 were killed. These frightful disasters so quickened the public con- science, and so plainly demonstrated that both humanitarian and economic needs demanded that steps be taken to prevent the re- currence of such accidents, that in 1908 Congress made a special appropriation for an investigation as to the "causes of mine ex- plosions." A similar appropriation was made in the following year. By act of May 16, 1910, the Bureau of Mines was created "to make diligent investigation of the methods of mining, especially in relation to the safety of miners, the use of explosives, the prevention of accidents," and other matters relating to mining. Therefore, these investigations are at present conducted in obedience to an organic act instead of being dependent solely upon special appropriations. The first appropriation became available July 1, 1908. Through the courtesy of the War Department a portion of the grounds and buildings of the arsenal at Pittsburgh was granted for the use of the technologic branch of the United States Geological Survey. Work was immediately begun in procuring and erecting the necessary instru- ments and appliances for carrying out the desired tests and inves- tigations and in adapting the existing buildings or in erecting new structures to contain the apparatus. The Pittsburgh testing station was officially opened and regular work was commenced on December 3, 1908, the apparatus and appliances having been tested, the force drilled in their use, and the equipment and methods inspected and passed upon by foreign experts.

Jan 1, 1912

By R. H. Nafziger

The Bureau of Mines evaluated 18 domestic titaniferous materials with widely varying compositions, mineralogy, and physical properties in electric-arc furnaces, Techniques were devised to recover both the titanium and iron values contained in these materials so that the reliance of the United States on foreign sources of higher grade ilmenites and rutile might be decreased. Most of the tested titaniferous materials responded well to lower grade or byproduct reductants, such as bituminous coals, charcoal, and coke breeze. Sufficient slag fluidity was realized by maintaining from 8 to 12 wt-pct iron in the slags; no contaminating fluidizers were required. Fluid slags containing up to 79, 70, and 54 wt-pct Ti02 were realized from east coast ilmenites, a rock ilmenite, and a titaniferous magnetite ore, respectively. A carbon-lined furnace shell is recommended for minimum slag contamination. Good results also were obtained during extended submerged-arc furnace tests.

Jan 1, 1980

By L. H. Adami

The heats of formation of anhydrous cadmium sulfate, cobalt sulfate, copper sulfate, nickel sulfate, and zinc sulfate were determined by hydrochloric acid solution calorimetry. The values at 298.15° K for formation from the metal, rhombic sulfur, and oxygen gas follow (cal/mole): CdS04J -222.0 ± 0.3; CoS04, -212.0 ± 0.4; CuS04) -183.4 ± 0.6; NiS04, -208.1 ± 0.2; and ZnS04, -233.1 ± 0.2. Corresponding heats of decomposition to form the metal oxide, sulfur dioxide, and oxygen were derived from these results; heats of decomposition to form the metal oxide and sulfur trioxide were also derived.

Jan 1, 1965

By J. E. Tiffany, J. J. McKitterick

"IntroductionThe Bureau of Mines is investigating the fundamental factors in breaking down coal at the face, which govern the production of lump coal in typical mines working, different coal beds. Tiffany and Nelson in 1923-21 conducted tests on methods of blasting and use of different explosives, in a mine working the Pittsburgh bed in Pennsylvania. They determined come of these factors quantitatively, and compared their results with those obtained when the regular mine practice was followed.Results of Previous InvestigationThe tests by Tiffany and Nelson showed that the use of the cartridge of smaller diameter than that used in mine practice, resulted in an increase of 5 per cent in the amount of lump coal passing over a 1-1/4-inch bar screen, with a reduction of 32 per cent by weight in amount of explosive required. On the other hand, they found that on reducing the weight of charge 20 per cent, and using the cartridge of larger diameter, the round would not throw down the coal satisfactorily.Experiments with ""snubbing"" showed a similar improvement in quantity of lump coal, end the coal that was blasted rolled forward into the working place. however, in recent tests at another mine where the coal Lad different physical characteristics, snubbing did not always result in the coal rolling forward, on account of clinging to the ribs, and was not found to be an advantage. Therein the writers of this paper recommend that tests be made before deciding upon the adoption of snubbing in a particular mine."

Aug 1, 1925

By F. N. Kissell, H. K. Sacks

This study examines the accuracy of area sampling for measuring the dust exposure of mining machine operators in coal mines. The specific objective of this research was to find locations where an area sampler might work better than earlier studies have indicated. The results show that fixed-location area sampling cannot accurately predict the dust exposure of a machine operator, even when the best fixed location is sought, the fixed location is quite close to the operator and the bias due to the dust concentration gradient is corrected. Industrial hygienists have known for many years that area sampling is unsuitable for measuring air contaminant exposures in the workplace. Near contaminant sources, the dilution air and the contaminants are not evenly mixed. Therefore, when workers are near contaminant sources, exposure measurements must be taken from the worker's breathing zone to be accurate

As mine haulage vehicles become larger, the danger to a driver during a fire emergency is increased by the greater height of the cab above ground. Also, property damage due to fires on bigger trucks can be substantial. To solve this problem, the Department of Interior's Bureau of Mines, through two research and development contracts with FMC Corporation, San Jose, California, has developed two reasonably priced, reliable automatic fire sensing and suppression prototype systems for large haulage vehicles. At the onset of the large mobile equipment fire protection contract effort, it was learned that fires were frequently experienced in open-pit mine haulage equipment, especially large trucks. As the size of equipment has grown, so has the hazard presented to an operator forced to leave his truck in a hurry when fire breaks out and his normal path to the ground is blocked by flames. His only recourse is to jump from the cab platform to the ground, and the one-story drop of 10 feet or more can severely injure him. It is with these factors in mind that a program was undertaken to provide a fire detection and extinguishing capability tor the large mobile equipment, especially trucks, used in open pit mines.

Jan 1, 2012

By Lucia Kuizon

The Cactus Springs Roadless Area Review and Evaluation (RARE II) study area (No. A5188) comprises 12,800 net acres (5,180 ha) in San Bernardino National Forest in west central Riverside County, California, about 20 air miles (32 km) southeast of Palm Springs. Mineral investigations are made by the U.S. Bureau of Mines on National Forest lands identified as Further Planning Areas in the RARE II program. The Bureau of Mines reviewed literature, mining claim records, and production files; examined the study area; and mapped and sampled mineral properties where appropriate.

Jan 1, 1983

By McMillan W. D.

Vermiculite is the name of a group of micaceous minerals characterized by their property of exfoliating when heated and thereby increasing many times their original volume. The resulting product has excellent heat-and sound-insulating properties, is used as a lightweight aggregate, and has numerous other industrial applications. Deposits of vermiculite occur in areas of pre-Cambrian rocks of the Llano uplift of central Texas, particularly in Burnet and Llano Counties. Because of the growing economic importance of vermiculite products, the Bureau of Mines undertook a detailed investigation of several deposits in Llano County. This investigation was completed in February 1947. The work comprised topographic surveys of five deposits, drilling with a 4-1/4 inch Parmanco power auger drill, and laboratory evaluation of samples. 342 drill holes, aggregating 4,905.5 feet, were completed, and 377 samples were taken. Laboratory evaluation of the vermiculite comprised expansion tests on both crude and beneficiated samples. The products obtained were compared with commercial-grade vermiculite from Montana.

Jan 1, 1949

By Donald W. Scott

Chemical thermodynamic properties for the ideal gas state from 0 to 1500 K are tabulated for all of the alkane hydrocarbons through C10. These properties are based on correlations of the extant data for the entropy, vapor heat capacity, and enthalpy of formation of individual alkanes and the equilibrium constants of alkane isomerization reactions.

Jan 1, 1974

By Albert L. Toenges

The introduction of mechanized mining in coal mines, which has speeded loading, has emphasized the importance of efficient underground transportation systems. The purpose of this investigation is to study and analyze various systems now in use, and to derive conclusions therefrom. This report may be helpful to operators who are planning new systems of transportation or who are revising present systems to increase their efficiency. This paper is the first of a series on this subject and describes some systems of transportation utilizing rail haulage. ACKNOWLEDGMENT The information used in preparing this report was obtained through the courtesy and cooperation of the officials of the companies whose mines were studied. The descriptions of the transportation systems at the mines included herein have been checked for accuracy, and publication of the data has been approved by the executives of the several operating companies.

Jan 1, 1940

By David T. Couillard

Task training is increasingly important in mining operations because of the ever-accelerating pace of technological innovations and the concomitant increasing complexity of mining equipment. This Bureau of Mines report describes two successful task training program In use in two open-pit taconite operations in northeastern Minnesota. The programs are different in approach, but both have improved safety and in- creased productivity while lowering costs. Methods of training both before and after passage of the 1977 Mine Safety and Health Act are described, and the impact of this act on task training at each operation is discussed. The report identifies four common principles that have contributed to the success of the two training programs and presents plans each operation has for improving future training through new technology.

Jan 1, 1984

By Richard N. Appling

This compilation presents information obtained through investigation of manganese deposits and a reconnaissance of potential manganese-bearing areas of southwestern Oregon and Del Norte County, Calif., from October 1952 to September 1955. The report includes maps, assays, and preliminary examination data on 39 manganese deposits distributed throughout Curry, Coos, Douglas, Josephine, and Jackson Counties, Oreg., and 1 deposit in Del Norte County, Calif. On the basis of mineral content the deposits can be divided into three groups: 1 Manganese silicate deposits, manganese oxide deposits, and manganiferous iron de-posits. Generally the oxides occur along the coast in the Curry-Coos County area, the manganiferous iron deposits are in the Josephine-Douglas area, and the manganese silicates are found in both the Josephine-Douglas and Jackson County areas. The deposits are characteristically irregular in form and usually small. Most silicate and manganiferous iron deposits are in metasediments of Triassic (?) age; oxide deposits are in sediments varying in age from Jurassic to Eocene.

Jan 1, 1957

By Christopher J. Bise

The objectives for the research project, "Coal Mine Injury Analysis: A Model for Reduction Through Training," were to identify and develop a means to indicate deficiences in human performance, job skills, and/or knowledge at a given mine site that are amenable to alleviation through training or job redesign, and to provide ;I set of analytical tools and training resources that will enable mine training personnel to effectively incorporate the noted deficiencies into a personalized model training program. The findings of this research project are contained in Light separate volumes. Volume I represents the Executive Summary of the study and provides a broad overview of the project's individual areas of emphasis and deliverables. The additional eight volumes provide greater detail on the development of a Model Mine Training Program based upon Professional Database Analysis, Incident Reporting, Loss Control, Job Safety Analysis, Risk Assessment, Cost/Benefit Analysis, and Mine Safety Management.

Jan 1, 1993

By Robert W. Thomas

This paper describing the mining practices at the Ray mines at Ray, Arizona, is one of a series being prepared by the Bureau of Mines on mining practices, method and costs in the various mining districts of the United States. At the present time (1929) all mineral Production of the Ray district comes from the Ray Mines of the Nevada Consolidated Copper Co. The ore body is being worked from two shafts, designated as No. 1 and No. 2. An undercut block-caving method of mining is used, variations of which are employed to fit different conditions. The present method has been developed by making improvements as experience was gained or when conditions changed. Refinements in practice are continually being made. The Ray mine was the first in the Southwest to use a caving system of mining on a large scale.

Jan 1, 1929

By Paul V. Mullins

Review and evaluation of all available data on the vapor pressure of car-bon dioxide at the ice point, including previously unpublished results obtained by the Bureau of Mines, are presented. Suggested corrections and adjustments to all the data yield an average value of 26,136.4 mm mercury. Indicated agreement is within plus 1 part in 8,000 to minus 1 part in 11,000. A novel pressure bomb in which a sample of pure carbon dioxide is placed and sealed by a diaphragm fluid separator and its use as a reference pressure standard for extended and repeated use in the calibration of deadweight gages is described.

Jan 1, 1966

By Manuel Gomez

The Bureau of Mines used data from 31 core samples to develop prediction equations for evaluating chemical and carbonization properties of six seam units in a lignite deposit approximately 2 miles wide and 8 miles long in the Wilcox Formation of central Texas. Statistical response surfaces, based on core analyses, were computed for 14 parameters indicative of lignite quality. These computed surfaces, and their mathematical equations, can be used to predict values of the selected properties of the lignite seams at any desired surface coordinate position between core hole locations. The wide range of application shown by this study indicates that the methods of statistical regression analysis may be useful to evaluate large deposits of lignite or higher rank coal.

Jan 1, 1969