Search Documents

By W. L. Parker, W. A. Selvig

"Introduction.Powdered or pulverized coal is extensively used as a fuel, the total annual consumption*** in the United States being about 12.000,000 tons, and growing steadily. As the coal is usually pulverized so that 70 per cent or more parses through a 200-mesh sieve, it presents difficulties in sieving, because such finely divided material tends to clog the meshes. A fineness test is desirable in order to judge the efficiency of the pulverizing apparatus, and as an indication of the particle size of the coal being burned.Committee D-5 on Coal and Coke, American Society for Testing Materials, has recognized the desirability' of a standard method for determination of fineness of powdered coal. The Bureau of Mines, in co-operation with this Committee, conducted sieving tests on two standard samples of powdered coal, which are described in this paper. As a result of this work a method for making fineness tests, by band sieving, is recommended as a standard method, while a rapid method, by machine sieving, is given for routine tests.Outline of Investigation.Preliminary trial tests were made by the bureau and tentative methods were formulated for making the sieving tests both by band and by machine.Each of two samples of powdered coal was carefully mixed, and portions were sent to the twelve laboratories mentioned later. These were requested to make duplicate sieving tests on the two standard samples, by the hand-sieving and machine-sieving methods, and to follow the tentative procedure exactly as outlined. All of the laboratories made sieving tests by hand shaking and eight of them made tests by machine shaking."

Nov 1, 1923

By T. E. Hill

The Bureau of Mines investigated the possibility of physically separating Missouri and Minnesota granites into commercially usable fractions of feldspar, quartz, and mica by mineral dressing techniques. The probability of r covering a feldspar fraction from raw granite suitable for commercial uses was developed through correlation of the iron oxide content by extensive petrographic studies. This probability evaluation also included Wisconsin granites and a high-feldspar iron ore concentration tailing from Missouri. Laboratory recoveries of feldspar and quartz were on the order of 80 percent. Mineral content of each fraction was generally over 95 percent, indicating excellent response to separatory techniques, Acid leaching of feldspar and quartz concentrates to remove iron oxide improved the grades chemically; however, occluded iron oxide particles in the leached products prevented attaining top grades of feldspar. Mica was removed as scrap grade at low recoveries. Each concentrate conformed to some category of commercial feldspar, quartz, or mica.

Jan 1, 1969

By G. R. Fitterer, E. A. Krockenberger, B. E. Sockman, R. B. Meneilly, J. F. Eckel, E. W. Marshall

"Steel manufacturers have noticed a decided tendency on the part of many of their customers to become more exacting in their steel specifications. Under these conditions, the steel must not only meet the specifications of physical properties (tensile strength, reduction of area, elongation, impact strength, grain size, normality, etc.) and the chemical analyses, but must also pass the inspection test of ""cleanliness.""By cleanliness is commonly meant the absence of oxide and sulphide inclusions. Other foreign particles such as furnace or ladle slag, ladle and runner brick, etc., must also be absent. The determination of cleanliness at present is usually made by microscopic inspection or macroetching.The rejection of steel for lack of cleanliness is increasing, out cleanliness is one of the most difficult requirements for the manufacturer to fill. The reason for this is that every steel inspector has a different conception of a. clean steel. A material which does not pass the examination of one inspector way be regarded as entirely satisfactory by the metallurgist of an¬other company. The cause of this confusion and disagreement concerning the definition of a clean or a dirty steel is simply that as yet no standardized procedure for the determination of impurities has been proposed and generally accepted, since many variables are encountered which interfere with the development of a satisfactory method. An idea of the complexity of this situation will be obtained from the following pages.A Survey of Proposed Analytical MethodsAlthough no analytical method has been accepted, many procedures have been proposed, as may be seen in Table 1. Therein are listed 16 of the better-known processes, pith references to the work of their originators, their mechanisms of determination, and their applicabilities. Among these is included the electrolytic method developed by one of the present authors, and some comparison between this and previously proposed procedures may be obtained by a study of the table. It appears that this new method Las many advantages over the others, and this paper presents a critical Study of its value."

May 1, 1933

By C. M. McKinney

The Bureau of Mines analyzed 626 crude oils from 546 oilfields in the United States that produced 2,500 BOPD or more during at least 1 of the last 3 years. Included also are crude oil analyses from eight fields that produced less but which were located in areas having few or no fields that produced 2,500 BOPD. The tables show the geographical and geological source, general characteristics. and determined and computed analytical data for each sample. The analyses were made according to the Bureau of Mines routine method and are directly comparable to other previously published analyses.

Jan 1, 1966

By R. W. Fatzinger

The accident-frequency rate for placer mining in 1942 is reported as 36.923 accidents per million man-hours worked. This figure places placer-mining accident frequency slightly higher than that given for quarrying-35.7-but considerably under the 78.0 for coal mining and 56.5 for metal mining.4 Placer mining is subdivided into four types of activity: Underground, surface, dredging, and hydraulicking. It is the purpose of this paper to present and discuss safety practices in dredging and hydraulic mining; therefore, the following considerations will be limited to these two types of placer mining.

Jan 1, 1948

By Guy A. Johnson

Combining contract and in-house research, the Bureau of Mines has developed and inmine-tested a novel device to improve the field-of-view of operators of off-highway mining equipment. This device utilizes a downward-looking, flat fresnel lens. The lens, plus louvers to reduce glare, is housed in a protective steel structure. The complete unit is called a blind area viewer. The viewer, when mounted on the right- front corner of the deck of most large haulage trucks, will increase a driver's direct field-of-view from about 35 pct (of where he/she has to drive) to about 80 pct. The improved visibility allows the driver to see possible collision hazards and roadway obstacles better, thus improving mine safety and increasing productivity. Economic analysis shows that the blind area viewers, which are now commercially available, pay for themselves in about a month on a 170-ton-capacity truck. The viewers are also applicable to other large mining equipment, such as front-end loaders, draglines, and downhole drills, or any place where seeing around a corner would be advantageous, such as along conveyor flights in processing plants during startups.

Jan 1, 1983

By Roy C. Bartholomae

This U.S. Bureau of Mines study found that the performance of the active noise cancellation hearing protector in a reverberant field was mixed. The performance varied when the conditions changed from ideal to nonideal. The active noise cancellation (ANC) component provided substantial additional noise reduction from 125 to 500 Hz for all testing conditions (broadband noise or pure tones both with and without safety glasses). While the ANC under ideal conditions provided additional attenuation from 500 Hz and below, under nonideal pink noise conditions the ANC amplified noise below the 125-Hz third octave band. There was a middle band of frequencies at which the ANC amplified noise levels ranging from 630 to 4,000 Hz. The results for pure tones showed that attenuations were higher but that they followed the same general trend.

Jan 1, 2010

By R. F. Abernethy

Analytical results, including ash fusibility data, are presented by the Bureau of Mines for 10 major constituents in coal ash from 373 samples of commercial U.S. coals. Determinations of Si02, Al2O3, Fe2O3, and P2O5 were made by colorimetric methods, Na2O and K2O by flame photometry, Ti02, CaO, and MgO by a spectrochemical method, and SO3 by a gravimetric method. In bituminous coal ashes the silicon, aluminum, and iron calculated as oxides often make up about 90 percent of the ash.

Jan 1, 1969

By Alan G. Mayton

A prototype end-cab shuttle car (SC) design has been developed to improve protection and address ergonomic concerns of the SC operator in low coal mines. The new design features an end cab transversely mounted to the SC and equipped with a closed-circuit video system. The end cab was retrofitted to a low-coal SC and evaluated in surface trials at the U.S. Bureau of Mines. During surface trials, test operators evaluated the end-cab SC relative to visibility; cab features-space, seating, controls, and operator position; tramming-inby, outby, and turning corners; and dumping. Trials were conducted using 12 test subjects; 6 were experienced SC operators. Results of the trials were promising. Of the experienced operators, the only operator with low-coal experience gave the new design the highest rating. Four experienced operators rated the end-cab design "better" to "much better" than a standard center-driven, side-cab SC for visibility when tramming, protection from roof and rib hazards, and no change in seat position with direction of travel. This report discusses research to modify a used 21SC JOY SC, retrofit the SC with the Bureau-developed end-cab, and evaluate the retrofitted end-cab SC in surface trials.

Jan 1, 2010

By W. F. Netzeband

This paper, which describes mining methods and practices at the Rialto zinc-lead mine American Zinc, Lead & Smelting Co., in northeastern Oklahoma, is one of a series being prepared by the Bureau of Mines on mining methods, practices, and costs in various mining districts of the United States, The Rialto mine is in the SE1/4 SW1/4 sec. 20 and the NW1/4 sec. 29, T. 29 N., R. 23 E., Ottawa County, Okla. (fig. 1). The 200-acre property is southwest of and adjacent to the town of Picher in the central part of the Picher field of the Tri-State zinc-lead mining district (fig. 2). Other mines of the company adjoin the Rialto on the east and south. Zinc-lead ores have been mined almost continuously from the Rialto tract since 1916. The property was acquired by American Zinc, Lead & Smelting Co. late in 1951, and the mine was operated thereafter by the Nellie B Division of that company until the end of 1955, when it was subleased to the Residue Mining Co.

Jan 1, 1958

By Warren E. Morrison

A simplified energy model for the United States is quantified for a recent historical period. The basic model and calculated quantified structures are used for a number of analytical case studies that estimate midterm and long-range shifts in patterns of energy resources demand and required supply. Historical data series are presented for the years 1947 to 1965 in the form of integrated energy balances by source, form, and consuming sector. In case studies I to XII, conditional projections of historical trends of energy demand and required supply are made for the midterm period 1966 to 1980. The projections are carried out by correlation of major energy components with relevant independent variables such as major economic indicators. Simulations of the medium-range projections to 1980 are carried out by varying the assumptions for the determining variables to produce high-and low-range projections for the midterm period. Case studies XIII to XXII are long term contingency or technological forecasts to the year 2000. These cases assume technological changes or innovations that produce major shifts in the long term pattern of energy consumption and the mix of required resources. The domestic resource base is assessed in its ability to meet projected or forecast demand for energy resources under the midterm and longrun assumptions made in the various case studies. Various energy issues or problems identified from the analyses of the case studies are discussed, and possible alternative approaches to solutions to these issues or problems are suggested.

Jan 1, 1968

By G. B. Atkinson

The Bureau of Mines investigated a method for increasing the leaching rate of bulk superalloy scrap to facilitate recycling and recovery of critical metals such as Ni, Co, and Cr. Three superalloys were investi- gated, the cast-nickel-base superalloy IN-738, the wrought-nickel-base superalloy Rene-41, and the cast-cobalt-base superalloy Mar-M-509. Superalloys melted with 20, 30, 40, and 50 pct Al metal to form inter- metallic compounds were easily crushed to a convenient particle size and reacted rapidly with acid solutions which dissolved the metals. For example, leaching 1/2-in pieces of unalloyed IN-738 with excess 6N HC1 at 95° C for 2 h dissolved about 0.5 pct, while leaching 10 g of minus 20-mesh 30 pct Al-70 pct IN-738 with excess 6N HC1 at 95° C for 2 h dis- solved 96.2 pct.

Jan 1, 1983

By J. R. Thoenen

This circular is the third of a series summarizing the technical problems involved in the production and preparation of sand and gravel. The first, Information Circular 6668, published in December 1932, discussed the problems involved in prospecting and exploration. The second, Information Circular 6689 (March 1933), dealt with the development of gravel deposits. This is part I of a paper designed to present a study of problems arising in the excavation of sand and revel and their delivery to the treatment plant. Other circulars are planned which will discuss preparation of the material for market, plant storage, and miscellaneous subject. Definitions For the purpose of this circular, excavation is defined as the recovery of sand and gravel from developed natural deposits and their delivery to a plant for market preparation.

Jan 1, 1934

By A. H. Roberson, F. S. Wartman

For many years , it has been the common practice at most copper mines to recover copper in solution in effluent mine water by precipitating the copper with scrap iron.4/ The technique employed varies from simply throwing scrap iron or tin cans into the waste ditches to passing the water through elaborate launder systems containing detinned scrap and baled cans . In general , a considerable amount of low - cost copper has been recovered that otherwise would have been lost . Iron consumption usually varies from 1 to 1-1/2 pounds of iron for each pound of copper recovered . The grade of the precipitate may be as much as 90 percent copper.4/ ,5/ Where the consumption of iron is materially greater , its cost is likely to be the determining factor of profit . In times of emergency, when the demand for scrap iron for remelting increases the cost of the iron sharply, and the supply of tin cans is not large enough to meet requirements , recovery of the copper might not be economical . The three principal reactions that take place when an acid mine water containing iron and copper salts in solution is brought into contact with metallic iron are : (1 ) Copper is precipitated and an equivalent amount of iron is dissolved , CuSO4 + Fe Cu + FeSO4 ; ( 2) ferric salts are reduced to ferrous salts , Fe2 (SO4 ) 3 + Fe = 3FeSO4 ; and (3) the free acid in the solution reacts. with metallic iron to produce ferrous sulfate , H2SO4 + Fe = H2 + FeSO4 . = Because of the reported high.consumption of iron (5 to 6 pounds per pound of copper precipitated ), when copper in water from the Hornet mine of the Mountain Copper Co. ( California ) was precipitated upon scrap iron , a series of tests was made to determine . the . optimum treatment, time , and consumption of iron .

Feb 1, 1944

By Yael Miron

Coal mines that undergo self-heatings, and specifically mines that sustain both floor heave and self-heatings, would benefit from the use of sealants to minimize air ingress to susceptible areas. The U.S. Bureau of Mines(USBM) evaluated three sealant systems for this purpose, bentonite-water mixtures, silicate gel, and guar gum gel. The guar gum-based gel was the only sealant that possessed the desired properties of elasticity, ease of preparation, adaptability to the mine, and a long life. In addition, since the gel consists mostly of water, it could quench or cool nearby heatings. Optimal formulations were determined in laboratory tests, and then tested in the USBM Safety Research Coal Mine. Two formulations resulted in stable gels that lasted for at least 12 months in the mine. Semi continuous preparation of gel using an eductor was evaluated and appears feasible. Although guar gum gel is expensive, selective use to prevent heatings in specific areas would be cost-effective, both interms of productivity and enhanced mine safety.

Jan 1, 1995

By J. F. McIlwain

The Bureau of Mines investigated fumes generated by selected welding materials used in mines in order to help determine their relative hazard potential. The initial phases of the study have been completed. A welding-fume generation and collection apparatus was designed, assembled, and calibrated. Five brands of coated, AWS-type E308-16 stainless steel electrodes were tested. Total fume generation rates of 0.39 to 0.51 g/min were measured. Quantitative chemical analyses were conducted for all of the principal firms constituents. Two analytical schemes were used to determine levels of the Cr6+ and Cr3+ species contained in the welding fumes; comparable results were obtained. The Cr6+ was found to be the most hazardous constituent, leading to a maximum allowable total fume exposure of 1 mg/m3. Fume generation rates and fume constituent analyses will be derived for other groups of welding electrodes using similar procedures.

Jan 1, 1983

A construction material based on plasticized sulfur and mineral aggregate, that is superior in corrosion resistance and strength to portland cement concrete. The material can be used in the chemical, metallurgical, and fertilizer industries, and will also provide an attractive market for by-product sulfur resulting from compliance with pollution regulations. How It Is Made Sulfur concrete is thermoplastic material. Plasticized sulfur is mixed with sand and gravel aggregate heated to 375-400° F. The sulfur melts and acts as the binder or cement. The sulfur concrete is poured hot and sets at a temperature of 200° F. Full strength is attained in a few hours, compared to several days for portland cement concretes. Sulfur concrete even pours and sets in freezing weather. Although unmodified sulfur with aggregate will produce a sulfur concrete with good initial properties, it undergoes crystallographic modifications, and deteriorates with time, particularly when exposed to moisture or freeze-thaw conditions. The Bureau of Mines has developed plasticizers which, when reacted with the sulfur, give sulfur concretes with excellent moisture and freeze-thaw resistance. The plasticizers are based on mixtures of dicyclopentadlene (DCPD) and ollgomers of cyclopentadiene. About 5 percent by weight of the plasticizers is reacted with molten sui fur for several hours. The sulfur cement can be used directly or allowed to solidify for easier handling and storage.

Jan 1, 1981

By V. F. Parry, W. S. Landers

"INTRODUCTION The primary object of this investigation was to determine changes in physical and chemical properties of subbituminous lump coal while in storage for 8 months in a typical residence and to demonstrate how this fuel may be stored without degradation or spontaneous combustion. The second object of the study was to determine how the stored coal performed in a hand-fired furnace operated under practical conditions.The investigation revealed that if care is exercised in placing sub-bituminous lump coal in a closed bin, no significant slacking or degrada¬tion occurs, no hazards arise, and over-all indicated efficiencies of about 65 to 69 percent can be obtained under practical,firing conditions that the average home owner can meet.Owing to the war emergency, much attention is being given to the proper storage of coal, and campaigns are being conducted to increase the quantity of coal being stored to relieve transportation and production overloads. Ordinarily, coal dealers do not recommend storage of subbituminous coal in homes owing to deterioration of the coal and to possible hazards from spontaneous combustion. This practice has grown from some troubles that have been experienced, which can be traced to improper preparation, improper bins, and poor technique in placing coal in a bin. There is no good reason why subbiturninous lump coal cannot be stored safely in homes."

Jun 1, 1944

By R. A. Friedel, J. L. Shultz, A. G. Sharkey

The purpose of this investigation was to study the primary materials associated with the coal structure . Mass spectrometric techniques can be useful in studying the chemical structure of coal and various high- molecularweight materials derived from coal . Investigations of pyrolysis products and extracts of coal , and also whole coal , showed : 1. Aromatic hydrocarbons obtained by the vacuum pyrolysis of coal below 300 ° C possibly were sorbed material rather than decomposition products . 2 . 2 . Thirteen structural types having molecular weights from 78 to 400 were identified in pyridine extracts constituting one - quarter or more of the coal by weight . 3. Material extracted at room temperature with a methanol - benzene solvent and a vacuum pyrolysis condensate obtained at 450 ° C contain similar components . The extract and the condensate have approximately the same average molecular weights ( 200-300 ) . 4. Material extracted from coal at room temperature is altered even by mild thermal treatment . 5. Changes in various alkyl series occurring in thermally treated coal extracts can be followed quantitatively . 6. Similarities in the spectra of coal and graphite were indicated in an investigation using a mass spectrometer equipped with a spark source . Determinations on a coal - ash sample by this technique showed good agreement with data obtained by emission spectroscopy .

Jan 1, 1963

By W. G. Freeman

This study provides recommendations for improved safety in underground blasting procedures based on in-mine observations of blasting practices in 30 underground metal, non-metal, and coal mines, and the analysis of blasting accidents since 1970 and existing state and federal regulations pertaining to the storage and use of explosives. Results of these analyses and observations indicate that 1) blasting accidents have declined but are an important contributor to the hazards of underground mining; 2) existing regulations are essentially adequate; 3) greater emphases should be placed on human errors and unsafe practices and the enforcement of existing regulations; and 4) future revisions of these regulations and standards should be organized, and their intent coordinated to eliminate ambiguities.

Jan 1, 1980