Search Documents

By G. T. Krempasky

This report covers the installation and evaluation of lb reinforced concrete sets, 6 in each of 3 mines in the Goeur d'Alene mining district, Shoshone County, Idaho, and is the second of a series to determine the feasibility of a more permanent type of mine support. Closure measurements, where applicable, were made periodically of the concrete-set installations and were compared to the initial cross section of the sets. A different method of blocking was used at each test site; at one test site the type of blocking was changed several times during the test. Results from each test site are reported separately. No attempt was made to compare the cost of the concrete installations with the cost of other types of support used in the district. Such an evaluation of permanent types of support would require a longer period of time. At this time, tests are not complete enough to determine the applicability of underground concrete supports. However, results to date tend to confirm the general opinion that precast concrete mine supports could be used to advantage in openings that require support and must have long life, especially where decay of timber is an important factor.

Jan 1, 1963

By Kenneth L. Rubow, Virgil A. Marple

"INTRODUCTION Respirable dust is defined as the dust which penetrates to the alveolated regions of the lungs. Due to the size selective nature of the particle removal mechanisms in the nasal passages and lung airways, criteria defining respirable particles must be a function of the particle size. Three criteria defining respirable particle penetration are shown in Figure 1. These criteria have been defined by the British Medical Research Council (BMRC), the American Conference of Governmental Industrial Hygienists (ACGIH) and German TBF 50-11 (1).The quantity of respirable particles in an aerosol can be measured by use of two-stage samplers. The first stage consists of a particle preclassifier with penetration characteristics corresponding to one of the respirable penetration curves in Figure 1. The large nonrespirable dust particles are removed from the airstream in the preclassifier and the smaller respirable dust particles pass on to some device which can measure their concentration (the respirable dust concentration).Instrumentation for the measurement of respirable coal mine dust has been limited by the severe conditions existing within the coal mine. The conditions of particular importance are the methane atmosphere, high humidity, and the general non-laboratory type environment. The most severe of these conditions is the methane atmosphere since any electronic or electric powered instrumentation must be intrinsically safe to operate in such an atmosphere.In spite of the difficulty of sampling respirable dust within the mines, many instruments have been developed for in mine use. Although these instruments operate under a variety of principles they generally fall within two categories: personal samplers and area samplers.A personal sampler is worn by the mines while he is performing his duties in the mine. These devices are generally small, light weight and require little power so as not to interfere with the miner's ability to work."

Jan 1, 1988

By Jos. R. Guiteras

This paper is one of o. series describing mining and milling methods and costs being published by the United States Bureau of Mines. It presents the results of a study of the Alice mine by the writer in December 1936. ACKNOWLEDGMENTS Acknowledgment is made to J. Fred Johnson, mining engineer off the American Smelting & Refining Co., for permission to visit the property; and to Arthur F. Johnson, general superintendent at the property, for his friendly cooperation in contributing the information contained in the paper.

Jan 1, 1939

By J. Robert Wells

The Bureau of Mines has developed a spectrochemical procedure for determining 19 impurity elements in high-purity titanium metal, titanium oxides, and titanium halides in which all samples are converted to titanium dioxide. Determination of these impurities was studied in the general concentration range of 0 to 1,000 p.p.m., but different determination limits were found for the various elements. The procedure is quantitative for 18 elements but semi-quantitative3 for beryllium and has an overall relative standard deviation of 15.8 percent. Two mixtures were used, one composed of graphite and lithium carbonate plus gallium oxide and the other of graphite and lithium carbonate plus germanium dioxide. Each mixture was blended mechanically with an equal weight of titanium dioxide. Lithium carbonate served as buffer-diluent. Gallium was the internal standard for 1 impurity element, germanium for 7, and titanium for the remaining 11.

Jan 1, 1962

By Joseph M. Singer

This research project had two main objectives: (1) To identify the smoke limits of gaseous fuel-air mixtures and (2) to obtain and evaluate basic chemical information on the formation of smoke in very rich flames near the smoke limit. Such information would do much to establish the circumstances for car-bon deposition in gas appliances and in other types of combustors. Based on tests with ethylene and propane, these studies showed the following: 1. Smoke limits are related to the yellow-tip limits of the fuel. Previous research established sufficient data to permit prediction of yellow-tip limits on gas burners using a wide variety of fuels. The present study of smoke limits deals only with ethylene-air flames, but the concept that was developed is probably applicable to other fuels.

Jan 1, 1962

By J. Patrick Ryan, Thor H. Kiilsgaard, Charles W. Merrill, E. T. McKnight

The U.S. Treasury stocks of silver have been reduced at such a rapid rate to meet industrial and coinage requirements that they face exhaustion in 3 or 4 years. Alleviation of the silver problem will require increasing supply or reduc ing demand. This paper examines poss ible long-range resource development and research programs and improved secondary recovery. The possible reduction or elimination of silver in coinage and development and introduction of substitutes in the arts and industry are also discussed.

Feb 1, 1965

By D. E. Wolfson

This report describes the carbonizing properties of the principal coal beds of Allegheny County, Pa., which rank low in the high-volatile A bituminous classification. Seven coal samples from 3 coal beds were selected for study, as follows: 2 each from the Redstone and Pittsburgh beds and 3 from the Upper Freeport bed. Selection was based on estimated reserves. The samples of Upper Freeport and Pittsburgh coals were satisfactory chemically for producing metallurgical coke. The ash contents of the samples of Redstone coal were moderately high. One of the samples of Redstone coal was high in sulfur content, and it would be difficult to upgrade to meet present metallurgical standards.

Jan 1, 1959

By P. R. Moyer

"INTRODUCTION The Federal Explosives Act (55 Stat., 863), as amended, was passed by Congress on December 26, 1941, and became effective immediately; it amended the Act of October 6, 1917 (4o Stat., 385). The purpose of the Act was to regulate the manufacture, storage, use, and possession of explosives in order to prevent sabotage and to assure that explosives and ingredients would not fall into unauthorized hands. Under the provisions of the Act, the Director of the Bureau of Mines was authorized to administer its provisions under the supervisions of the Secretary of the Interior.EXPLOSIVES-CONTROL DIVISIONTo administer the Act, necessary personnel were employed in accordance with the appropriation made from a special presidential fund and later by Congress, and the Explosives Control Division was organized as a part of the Health and Safety Branch of the Bureau of Mines constituting the fourth division of that branch. A central office was established in Washington, D. C., and field offices were designated largely at the offices of the Health and Safety Branch throughout the country, and 50 explosives investigators were employed and assigned to work from these offices under the direction of the district engineers of the eight districts into which the United States is divided by the Health and Safety Branch. The territory assigned to each investigator was based on the approximate amount of explosives stored in that area; however, smaller territories were assigned to investigators stationed near the Pacific coast, which was indicated as critical by the armed forces."

Mar 1, 1947

By E. J. Lintner

This paper is one of a series being prepared by the United States Bureau of Mines describing clay mining and crushing methods and costs at various operations throughout the United States. These papers are designed to disseminate technical information regarding methods used. The cost tabulations represent local operating expenditures only and not total production costs. It is recognized that publication of total production costs might, in many instances, cause embarrassment to the individual operator as well as to the industry as a whole. On the other hand, operating costs are essential to a technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations may ensue. The author wishes to acknowledge the assistance of the following persons: L. W. Camp, general manager; S. Cooper, plant superintendent; and W. R. Riel, office manager.

Jan 1, 1936

Comparative tests of four coals used industrially for coke production have been made by three laboratories of the Federal Bureau of Mines, each using its standard equipment and procedures for evaluating coal for coking. Two of the coals were blends used in the western and eastern sections of the United States, the third was a strongly coking coal widely used for producing coke in Alabama, and the fourth was a blend typical of those used for producing foundry coke in the Birmingham district. The coals used and the cokes produced from them covered a wide range of chemical and physical properties. The tests used at all three laboratories for determining the physical properties of the cokes were made according to ASTM (American Society for Testing Materials) methods. The excellent agreement found for the physical properties of the cokes indicated that, for the coals tested, the BM-AGA (Bureau of Mines-American Gas Association) 18-inch circular retort used at Pittsburgh, Pa" the 14-inch slot-type oven used at Denver, Colo., and the 17-inch slot-type oven used at Tuscaloosa, Ala., were substantially equivalent for evaluating coals for production of coke. Thus, added value is given to data obtained previously and independently at these three Bureau laboratories. INTRODUCTION Laboratory equipment to produce coke for evaluation has not been standardized by the industry. The results obtained with anyone design of equipment have been regarded as showing only the relative values of coal to produce coke of the requisite quality. Few systematic studies have been made to correlate results obtained in different types of equipment. Results of one, in which the Bureau of Mines participated, were published recently.2/ This

Jan 1, 1961

By A. L. Engel

This report is a compilation of results of brief preliminary tests on sulfide ores that contained gold and silver and, in some cases base metals. It is a companion paper to a recent similar report on oxide ores. Simple treatment methods employing the least possible equipment sometimes produce satisfactory results on marginal ores and in small-scale operations. Investigations of typical ores from newly discovered or recently explored mining districts have been made in continuation of a long-established part of the hydrometallurgical and ore-dressing program of the Reno station, Bureau of Mines. The purpose of such investigations is to encourage the search for and development of mineral resources and particularly to assist in the economical exploitation of low-grade and marginal ores as well as the conservation and recovery .of values in products that were discarded from former operations because of inability to treat them profitably. Several of these investigations have been limited to preliminary tests of samples from prospecting operations, whereas same involved samples of old dumps or tailings piles. The test work in these cases was not extensive enough to warrant publication as individual reports, but is of considerable interest inasmuch as it indicates the possibilities as well as the limitations of treating the respective materials. The samples were representative of the districts from which they wore obtained, so this information should be helpful in the future development of these districts.

Jan 1, 1951

By L. A. Panek, A. J. Barry, John A. McCormick

"INTRODUCTION During recent years, roof bolting has become widely accepted as a systematic method of supporting both coal- and metal-mine roofs. Today, over 2 million roof bolts are installed monthly. Most of the information on bolt installation procedure reported to date (1,2,3,4,5,6) 3/ has been obtained by trial and error by individual groups or operators. To insure good roof control, experience and field tests have indicated that roof bolts should be installed immediately after the exposure of new roof, and they should be preloaded enough to minimize sag of the roof over the opening. The question of the proper initial preload for roof bolts is under study, although it is a general practice to impose an initial load on a bolt of approximately 10,000 pounds. This created a problem of measuring bolt loads at installations in underground mines, which was partly solved by using a commercial-type torque wrench; a device that permits a direct reading of the torque applied to the nut on a roof-bolt assembly from which the corresponding load can be determined by referring to specifications furnished by the manufacturers. However, considerable apprehension was expressed regarding the accuracy of this measuring procedure because of variations in the manufacture of roof-bolting materials and the degree of care exercised in making bolt installations. In the process of loading a bolt, only a small part of the effort is expended in producing strain in the bolt - the larger part of the effort is used in overcoming frictional effects in the nut-bolt-washer assembly. These frictional effects are subject to many factors, such as condition of threads, type of lubrication, if any, the finish on the nut and bearing plate, and the alinement of the bearing plate on the bolt. The object of this investigation was to determine the accuracy with which the load developed in a slotted-type roof bolt installed in a conventional manner in shale or sandstone roof rock can be determined from the torque applied to the nut.This report is the first of a series relating to basic research in roof bolting in underground mines. A future report will cover results obtained using expansion-type bolts under similar conditions. Other reports will consider the efficiency of bolt anchorages, the long period stability of bolts, and the design of safe and efficient roof-bolting systems."

May 1, 1953

By R. L. Grant

[p(,ton~to'rs 'ar-IV uscG.. to explode 9crnli .... sible c}:plosivcs, dynamites, or other hiGh uxplosives. This ?,...!xplosion or detr)nation is brought about by th\.:J energy which i liberated as a cOl":"Lb' nation of concusBion and heat wl1en the ? detonator is fired. 'm Ot:18t? I'l(jrds~ liThe detonator is the key VI: ich unlocks the enerGY of a llgh? explosIve""? (8) :1/. Being sensitive nd latently dangerous, detonators ITl.ust lTIeet t\V0 primary requirerDentr: They must be ..;.afe to handle and IT. list? detonate' when (l,esired, the ... eby iIr.parting deton:l.tion to the explo8ivc cJ.1Cire-e.]

Jan 1, 1941

By David Schlain

This Bureau of Mines report describes a method for electrodepositing titanium diboride from a molten salt bath. Initially, the electrolyte is a mixture of LiBO2, NaB02, Na2 Ti03 , Li2Ti03, and Ti02? The cell is operated at 900° C in a dry, inert atmosphere with consumable anodes of titanium or hot-pressed titanium diboride (TiB2) powder. Agitation of the electrolyte is essential. Current densities may be 6 to 9 amperes per square decimeter (amp/dm2) with titanium anodes and 9 to 30 amp/dm2 with titanium diboride anodes. A current density of 6 amp/dm2 is equivalent to a plating rate of about 35 micrometers per hour. The adherence of the TiB2 deposit varies with the substrate material. It is most adherent on molybdenum and on 4130 steel that has been preplated with copper and nickel, less adherent on nickel, and still less adherent on Inconel and on 4130 steel without the preplate. Cathode and anode reactions are suggested.

Jan 1, 1976

By B. J. Moore

This publication contains routine analyses and related source data for 547 natural gas samples from 22 States and three foreign countries. Of this total, 340 samples were collected during calendar year 1967. The remaining 207 analyses are of samples collected during previous years, but releases granting, permission to publish the results were not received until 1967. All samples were collected as a part of a continuous survey of the free world for occurrences of helium in natural gas. The Bureau of Mines has conducted this survey in the United States since 1917, and in 1965 it was expanded to include foreign gasfields. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus which are described in Bureau of Mines Bulletins 4863 and 516.4 Nine previous publications have been made to present results of 7,618 gas analyses made by the Bureau of Mines Helium Activity prior to 1967. The first three, Bulletins 486,5 576,6 and 6177 contain analyses and related source data on 5,218 gas samples collected from 1917 through 1960. The other six

Jan 1, 1968

By Carlton E. Brown

Brown and Yant6/ recently described a microprojection method for determining the particle-size distribution and number concentration of samples of dust collected from the air by such samplers as the Owens jet dust counter7/ and the thermal precipitator8/. This method was developed to obviate or reduce the eyestrain consequent to the regular filar-micrometer method9/ and to save time and work. The article stated that work was in progress on a microprojection method for courting impinger dust samples; this article describes the method developed. ACKNOWLEDGMENTS The assistance of the personnel of the Ventilation Department of the Anaconda Copper Mining Co., Butte, Mont., in developing this method and particularly in suggesting a suitable material to use for the microprojector screen is sincerely appreciated. Much of the work was done in the laboratory of the Anaconda Copper Mining Co. on samples collected in Butte mines during a cooperative study with this Bureau.

Jan 1, 1938

By Carlton E. Brown

Broom and Yant6/ recently described a. microprojection method for determining the particle-size distribution and number concentration of samples of dust collected from the air by such samplers as the Owens jet dust counter) and the thermal precipitator8/ . This method was developed to obviate or reduce the eyestrain consequent to the regular filar-micrometer method9/ and to save time and work. The article stated that work was in progress on a micrcprojection method for counting impinger dust samples; this article describes the method developed. ACKNOWLEDGMENTS The assistance of the personnel of the ventilation Department of the Anaconda Copper Miring Co., Butte, Mont., in developing this method and particularly in suggesting a suitable material to use for the microprojector screen is sincerely appreciated. Much of the work was done in the laboratory of the Anaconda Copper Mining Co. on samples collected in Butte mines during a cooperative study with this Bureau.

Jan 1, 1938

By W. W. Agey

As a result of a field examination made during the Bureau of Mines intensive manganese program, three lots of ore were procured from the famous old Paymaster District, 7 miles from Midway Wells, Imperial County, Calif. This district is an old producer and shipped approximately 10,000 tons of 45-percent manganese ore during World War I. A 2-ton lot of ore was taken of a Bureau engineer from the exposure of a small fissure vein in conglomerate on the Turtle Group of claims; 1 mile east of the Pacific Coast Manganese Corp. claims. The vein material consisted of manganese oxides, calcite, and quartz in fairly coarse association.

Jan 1, 1949

By J. W. Thompson

The term "minerals" when employed in a conveyance in the State of West Virginia is understood to include every inorganic substance which can be extracted from the earth for profit, whether it be solid, as rock, fire clay, the various metals and coal, or liquid, such as salt, and other mineral waters and petroleum oil and gas. Horse Creek Land & Mining Co. v. Midkiff (West Virginia), 95 Southeastern 26, p. 27. TERM INCLUDES OIL AND OAS. The term "minerals" used to describe the interest in land granted or reserved bona fide includes petroleum oil and natural gas. Horse Creek Land & Mining Co. v. Midkiff (West Virginia), 95 Southeastern 26, p. 27. INJUNCTION TO PREVENT RElllOVAL. The removal of ore from the premises of another without his consent will be enjoined. Barnes v. Esch (Oregon), 169 Pacific, 512, p. 518. TITLE TO MEXICAN BULLION-JURISDICTION OF FEDERAL COURTS TO DETERMINE. Where bullion within the jurisdiction of the Mexican Government was seized, condemned, and sold for war supplies by the Constitutionalist forces in the revolution acting under authority from Gen. Carranza, claiming to be the provisional President of the Republic of Mexico, a United States district court of Texas, into which State the bullion has been imported from Mexico, has jurisdiction to try and adjudge as to the validity of the title acquired by and through the seizure, appropriation, and sale by the Carranza forces as against an American citizen claiming ownership of such bullion prior to its seizure.

Jan 1, 1919

By D. H. Platt

Data obtained from on-the-site observations have been compiled to describe the equipment and installation methods used for satisfactory suspension roof support in a large-diameter tunnel. Experimental roof bolting was undertaken from June 1950 until May 8, 1951, in the East Delaware tunnel, which is part of the Delaware aqueduct in Delaware and Sullivan Counties, N. Y. Revised suspension-roof-support plans and specifications were prepared during the spring of 1951 by the City of New York Board of Water Supply; these were approved by the State of New York Department of Labor April 13, 1951, and adopted by the City of New York Board of Water Supply on May 8, 1951.

Jan 1, 1952