Search Documents

By E. L. Garton

The Bureau of Mines for a number of years bas been conducting an investigation of crude petroleum from producing fields in the United States and the Western Hemisphere and has published a series of reports on these fields. Analyses of crude-oil samples from many oil fields of Oklahoma are given in Bulletin 2915. Analyses of 21 representative crude oils from various producing zones of the Oklahoma City field are given in this report. A close study of the analyses reveals very few differences in the general characteristics and chemical properties of these oils.

Jan 1, 1932

By E. C. Pattee

A mobile spectroscopic laboratory was completed by the Bureau of Mines in 195 to provide a rapid, inexpensive means of field testing samples for beryl¬lium and other associated metals of possible commercial importance. Spectro-copes have been used in laboratories for many years in various types of research and routine analyses, but this spectroscope is probably the first mobile unit. The laboratory provides for spectroscopic, radioactivity, fluorescent, and limited chemical tests of samples. The unit has been a valuable reconnaissance tool. It has been used to search for beryllium, cesium, columbium, tantalum, rubidium, and lithium in Idaho, Washington, and Montana. Several very low grade deposits of these elements were found, and occurrences of other important elements were identified; however, none are of economic importance. The spectroscope permits the detection of elements by analysis of visible light produced when elements in a small powdered sample are volatilized in an electric arc., A total of 70 elements can be detected; 29 can be detected at or below 0.01 percent, Electric power for the arc is supplied by a gasoline motor-driven generator, Equipment is housed in an aluminum van, mounted on a 4-wheel-drive vehicle for easy maneuverability on mountain roads, A trailer with crushing, pulverizing, and splitting equipment permits the reduction of samples to a small representative pulp.

Jan 1, 1963

By A. Gene Collins

The Bureau of Mines undertook research to determine the bromide and iodide content of Mississippi and Alabama oilfield waters of the Tertiary and Cretaceous Period to determine genetic relationships of the ions, to determine their origin, and to determine their genetic relation to petroleum. The 280 samples were analyzed after a pretreatment to remove interferences. The iodide was oxidized to iodate and was titrated with thiosulfate. The bromide was oxidized to bromate and was determined iodometrically. A computer was used to calculate the correlation coefficients of iodide to bromide and to other ions. The other ions are sodium plus potassium, calcium, magnesium, chloride, bicarbonate, and sulfate. The mineral content of the samples ranged from 52 to 1,760 mg/l for bromide and from 2 to 65 mg/l for iodide. The mean bromide-to-chloride and iodide-to-chloride ratios were 0.0065 and 0.0002. The correlation coefficient matrix and linear plots indicated a definite bromide-to-calcium relationship for the brines investigated.

Jan 1, 1967

By R. V. Mrazek

The heat of formation of vanadium trichloride was determined at 298.15° K. Measurements were made in a solution calorimeter in which an aqueous hydrochloric acid-potassium dichromate solvent was employed. Data are presented for the heats of solution of vanadium trichloride and the vanadium trioxide "backup" compound, and for appropriate dilution reactions needed to preserve stoichiometry. The resulting heat of formation of vanadium trichioride (VCI3) at 298.15° K was found to be ?H°298.15° K = -138.89 ±0.37 kcal/g mole.

Jan 1, 1968

By W. L. Hunter

This report describes results of beneficiation and smelting studies conducted by the Federal Bureau of Mines on chromite samples from the Emma Belle and Seiad Creek prospects in the Seiad Creek area, northern California. Samples were chosen from this area because the ore is typical of disseminated types that represent a sizable domestic reserve. The two samples were similar in composition, and both responded in like manner to gravity beneficiation. As the ore was banded, considerable coarse gangue was rejected in laboratory sink-float from a minus-3/4-inch, plus-6-mesh fraction without excessive chromium loss at a medium density of 3.32. An average of 85.6 percent of the chromium was recovered in the sink product, which analyzed 35 percent chromic oxide (Cr203). Tabling yielded concentrates containing 49 percent or more Cr203; however, recoveries, ranged from only 33 to 45 percent. A combination of tabling and electrostatic separation of the table middlings showed that the chromium recovery could be increased to about 73 percent; the composite concentrate averaged 53 percent Cr203.

Jan 1, 1960

By James A. Whelan

The Bureau of Mines sponsored research studies of variables in rotary drilling, done in the Department of Mineral Engineering, University of Minnesota. By studying carefully controlled drilling with good instrumentation, it was hoped to obtain a better understanding of rock failure during drilling and of the stresses in drill bits during drilling. Experimental procedures and equipment are described. From these studies it was concluded that 1. Thrust requirements, other things being equal, are proportional to the total length of cutting edge in the bit. 2. Data from penetrating a wedge into rock under thrust only are not directly applicable to rotary drilling. 3, In rotary drilling the initial wear on a bit greatly decreases penetration rate under any given set of conditions; however, after initial wear the effect of wear on penetration rate is reduced. 4. An increase in rotary speed increases the overall penetration rate but decreases the penetration per revolution. 5. An increase in thrust increases the overall penetration rate and the penetration per revolution. 6, Torque on a drill bit is proportional to both penetration rate and bit diameter. 7. For small-diameter holes full-hole drilling will save both drilling time and energy compared with pilot drilling followed by reaming; for large-diameter holes pilot drilling-reaming is advantageous in both respects,

Jan 1, 1962

"It is evident that the incidence of coal worker's pneumoconiosis (CWP) or black lung disease varies in different coal producing regions of the United States. Many people have hypothesized about the reasons for the differing occurrences. Because underground coal mining involves many mining methods under changing geological conditions, several factors may be involved in contracting CWP such as: the amount of quartz in the respirable dust, the trace elements in the respirable dust, the rank of the coal that produced the respirable dust (bituminous, anthracite), the amount and size of respirable dust, etc.Recognizing the uniqueness of underground coal mining and CWP, research investigations involving seam characteristics, mining system and worker position are being conducted in the center to establish standard procedures for characterizing some coal properties that may be involved in workers contracting CWP. This has been accomplished by the in-mine sampling of airborne dust at various worker locations and mining system configuration and by performing laboratory analyses of mined material (coal and rock) taken from the mines. (FIGURE 49 and 50)The investigations includes a method of classifying coal seams according to their potential to generate respirable dust. It includes statistical analyses of the size and locational variations of the elemental compositions of respirable coal mine dust in operating underground mines from seams located in the eastern, midwestern, and western United States, and is currently completing research which is investigating the relationship between the elemental compositions of respirable dust sampled near a continuous-mining machine and a laboratory-produced respirable dust."

Nov 1, 1988

By J. B. Gayle

In a modern blast furnace, production depends, to a large extent, on the rate at which the furnace gases can be forced through the charge. Since these gases must make their way through the voids between particles of coke, ore, and limestone, the size and size distribution of the stock-column materials are of considerable importance. Also, because the coke pieces support the weight of the overburden and provide the majority of the voids through which the gases pass, their ability to withstand the shattering and abrading forces to which they are subjected should be related to the maximum obtainable production for any particular furnace. Although the wide acceptance of this point of view is indicated by the ever-increasing demand for stronger and more uniform blast-furnace cokes, economic considerations demand that a quantitative evaluation of the relation between coke quality and blast-furnace performance be made available to the industry at the earliest possible date. The following studies of size-distribution patterns and breakage processes were, therefore, conducted as a part of a preliminary investigation intended as a basis for future studies of the relation between coke quality and blast-furnace performance. The major findings may be summarized as follows: 1. New evidence for the presence of two independent distributions of sizes in run-of-oven cokes has been obtained, and a method for characterizing and estimating the relative importance of the individual distributions has been demonstrated. This method has also been used to study the different types of degradation taking place during the tumbler test.

Jan 1, 1954

By Floyd G. Anderson

The Federal Bureau of Mines promotes the use of safe and effective dust-collecting devices for rock drilling in coal mines. To insure that such devices are available to the coal-mining industry, the Bureau issues certificates of performance for dust-collecting systems and certificates of approval for dust collectors and rock drills or other mining equipment with integral dust-collecting systems that meet the requirements of an established Schedule.4/ Investigations are conducted under the provisions of the current revision of this Schedule by engineers of the Branch of Health Research. This circular describes briefly the requirements and procedure for obtaining certificates of performance or approval and lists equipment that has been certified as permissible under Schedule 25 or its revisions as of January 31, 1961. The names and addresses of companies to which certificates have been issued are listed alphabetically at the end of this circular.

Jan 1, 1961

By J. Douglas Causey

The Bureau of Mines conducted mineral investigations of the Peace Rock and Deadwood River roadless areas in Idaho, in 1992. Literature research was done by the Idaho Geological Survey. The study areas contain black sand placers (thorium, columbium, tantalum, titanium, uranium, and rare earth elements), gold, and molybdenum prospects. Except for unrecorded placer gold, there has been no mineral production from the areas. No mineral resources were delineated, but a multi-million tonne molybdenum resource is in the Big Pine Creek area and a 142 million m' black sand deposit is in the Stolle Meadows, Peace Valley, and Deadwood River areas. The Deadwood mine produced zinc, lead, and silver. There are six mining districts in and adjoining the areas; Warm Lake, Deadwood, Garden Valley/Lowman, Banner, Summit Flat, and Grimes Pass. Few claims, mostly placer, were active in the study area in 1992. The study areas are underlain by granitic rocks of the Idaho batholith. Most of the deposits are alluvial accumulations of heavy minerals weathered out of the Idaho batholith. Stockwork and narrow veins along shears account for the base and precious metal concentrations. Eleven prospects were examined. Workings consist of drill holes, pits and adits. Geothermal resources (hot springs) occur mainly along the Middle Fork Payette River; Vulcan Hot Springs is a designated Known Geothermal Resource Area. Sand and gravel resources are of local interest.

Jan 1, 1993

Create two air splits along the longwall face to isolate the shearer-generated dust to the immediate face area, maintaining a cleaner split of air in the workers' walkway.

Jan 1, 1994

By Mark I. Copeland

The formation of A1203 dispersoids 0,14 and less in size in dilute iron-aluminum alloys by internal oxidation in wet hydrogen and dispersion strengthening of iron by application of the technique to iron powder were found to be feasible by the Bureau of Mines. In flowing H2-1.5 H20 gas, A1203 dispersoids 0.1w and less in size formed (at 650° to 750° C) in Fe-l and 2 Al sheet material but not in Fe-3 or 4 Al alloys. With higher temperatures and/or higher H2O/H2 volume-ratio gases, A1203 and FeA1204 dispersoids >0.14 in size formed in all the sheet materials- Minus 100-mesh Fe 2 Al powders were internally oxidized under conditions that promoted formation of fine A1203 particles in sheet material, and then the oxidized powders were hydrogen reduced, sintered, extruded, and evaluated. During internal oxidation, fine A1203 dispersoids formed within the powder grains, and coarse FeA1204 particles formed on the powder surfaces and grain boundaries. The FeA1204 content was essentially eliminated during sintering by reacting with the unoxidized aluminum that remained in the center of the larger internally oxidized powders. The tensile strength at 800° C depended upon the aluminum-oxygen weight ratio of these elements in the extrusions and reached a maximum of 17,000 psi. The stress-rupture strengths at 800° C of the better alloys were comparable with those of type 310 stainless steel.

Jan 1, 1972

Objective To reduce dust generated from soiled floors within enclosed operator cabs. Background Enclosed operator cabs are widely used on mobile excavation equipment in the mining and construction industries. They protect the operator from bad weather, noise, and airborne dusts. The inside cab environment usually must be kept at very low dust concentrations because of quartz dust generated from the excavation of silica-bearing rock. For cabs to be effective in controlling airborne respirable dust, they must have an efficient air filtration system, while providing a positive pressurization of the cab interior. Ideally, the recirculated and exterior makeup air filtration should provide at least 99% capture efficiency for dust particles as small as 0.3-µmaerodynamic diameters. Many of these enclosed cabs use heating units mounted or directed along the floor (see figure 1), which can cause dust entrainment problems. Prior studies by the National Institute for Occupational Safety and Health (NIOSH) of enclosed cabs have shown that these floor heaters can generate notable amounts of dust within the cab enclosure (see Technology News 486). Multiple-shift dust levels measured inside a drill cab increased on average from0.04 mg/m3 during the summer months to 0.68 mg/m3 during the winter months. Additional dust level measurements, made with optical particle counters during a nondrilling time period, verified that dust levels inside the cab increased from 0.03 to 0.26 mg/m3when the floor heater/fan was turned on. Dust levels within the cab also became greater than the ambient air dust levels outside of the cab when the floor heater was turned on during the nondrilling time period. This shows that the floor heater was a notable dust source problem. Cab floors are commonly soiled from operators tracking dirt inside the cab upon entering from the mine or construction site. Interior cab dust levels can be increased by (1) airflow disturbance of the soiled floor or (2) operator disturbance of the soiled floor. Approach During prior NIOSH surveys of surface coal mine drills, several drills with very low cab dust levels (#0.1 mg/m3) were observed to have floor sweeping compound spread out over the cab floor during the working shift. This initial observation led to a more controlled A-B study of the effect of the sweeping compound on the interior cab dust levels. This study involved dust sampling with and without sweeping compound inside the cabs of a bulldozer and two drills. Sweeping compounds commonly use sawdust or cellulose as the main bulk material, with oil or wax added for dust adhesion purposes. Sand is sometimes added to increase bulk density. Sweeping compounds with sand are commonly used to sweep up concrete floors. Those without sand (usually referred to as "gritless") are used to sweep up smooth finished floors. Most of the oils and waxes used for the adhesive ingredient are petroleum-base and can have an irritating odor. People sensitized to petroleum distillates could have allergic reactions to these sweeping compounds. A few companies offer non petroleum-base sweeping compounds, using either a natural oil or chemical additive for dust adhesion. During this study, it was decided that only the gritless sweeping compound (without sand) would be used, eliminating the addition of another potential silica source inside the cab. Since the sweeping compound would be applied on the enclosed cab floor for the duration of the shift, it was decided to use a canola oil-base sweeping compound to eliminate irritating odor from the petroleum-base sweeping compounds. The natural canola oil-base sweeping compound had a slight woody scent. The three pieces of equipment used in this study had notably different cab layouts. The bulldozer had a small cab with vents discharging air-conditioned or heated air from adjustable louvers at operator waist level and floor level. The bulldozer also had a cloth fabric seat and a carpeted floor. Drill A had a large cab with the heat directed from adjustable louvers at operator knee level and the air-conditioned air directed from cabin ceiling louvers. This drill had a vinyl fabric seat and a steel plate floor. Drill B had a small cabin with the heat directed across the floor (see figure 1) and the air-conditioned air directed down from the ceiling. It had a vinyl fabric seat and a worn rubber mat on a steel floor.

May 1, 2001

By E. C. Lane

This paper on the physical and chemical properties of crude oils from California fields is one of a series of reports on the oil-producing districts of the United States. The paper includes a short discussion of results, tabular data, and individual analyses of 16 California crude oils. Analyses of other oil from California have been published in Reports of Investigations 25954/, 26085/, 28466/, and 30747/. The samples were obtained by members of the San Francisco office of the Bureau of Mines. The collecting of the samples vas facilitated by the courtesy of representatives of oil companies in California.

Jan 1, 1937

By E. C. Lane

This paper on the physical and chemical properties of crude oils from California fields is one of a series of reports on the oil-producing districts of the United States. The paper includes a short discussion of results, tabular data, and individual analyses of 16 California crude oils. Analyses of other oil from California have been published in Reports of Investigations 25954/, 26085/ 28466/, and 30747/. The samples were obtained by members of the San Francisco office of the Bureau of Mines. The collecting of the samples vas facilitated by the courtesy of representatives of oil companies in California.

Jan 1, 1937

By A. E. Gooch

The Bureau of Mines conducted research in an attempt to provide a more sound basis for recommending improved artificial support during deepening of the main shaft of the Lucky Friday mine in the Coeur d'Alene mining district of northern Idaho. Field measurements of closure across the short axis of the 13-by 26-foot shaft were as high as 16 inches. Elastic/plastic finite-element (F/E) analyses were made, reducing the values of large-scale in situ rock mass properties until field closure measurements generally corresponded to displacements in the F/E analyses. Resulting plots of rock mass displacements, stresses, and areas of plastic failure display the results of creating openings (shaft, in this case) in deep mines in difficult ground conditions requiring artificial support.

Jan 1, 1976

By K. O. Bennington

The thermodynamic properties of hedenbergite, of composition [(Ca0,9516) (Mg0,0583Fe2+0.7134 Fe3+0.0934 Mn0,1366) (Si206)], were experimentally determined at the Bureau of Mines. The standard enthalpy of formation determined by hydrofluoric acid solution calorimetry is AHf298 = -680.96±0.855 kcal/mol. The standard enthalpy of formation from the oxides is AR-96 = -24.55±0.485 kcal/mol. Low-temperature heat capacities were determined by adiabatic calorimetry from 12.3 to 300.1 K. The derived standard entropy is S-98 - 41.218±0.148 cal/mol-K. High-temperature heat capacities were measured with a differential scanning calorim¬eter from 397 to 1,147 K. These experimentally determined data were combined with data from the literature to calculate the Gibbs energies of formation and equilibrium constants of formation over the temperature range of measurements. Standard enthalpies of formation are given as a function of temperature. The standard Gibbs energy of formation at 298.15 K is AGf298 = -641.90±0.86 kcal/mol.

Jan 1, 1984

By David P. Lindroth

The objective of this research by the Bureau of Mines was to determine the technical feasibility and associated pilot data for drying minus 1/4-in coal with microwave energy at a frequency of 2.45 GHz. The drying data were obtained experimentally on three coal types: bituminous, subbituminous, and lignite. The experiments were performed with a custom-designed conveyorized microwave oven having a continuous power capability of 12 kW. Drying efficiencies near the theoretical maximum of 1.54 kg of water per kilowatt hour of energy input were achieved for two coals and two sizes; overall drying efficiencies averaged 77 pct.

Jan 1, 1986

By J. W. Town

As part of the Federal Bureau of Mines titanium resources examination program, samples from seven deposits in the Pacific Northwest were tested for amenability to various beneficiation techniques. The samples obtained by the Bureau's Office of Mineral Resources at Spokane, Washington represent a large potential source of titanium. This report summarizes the results of tests at the Bureau's Metallurgy Research Center, Albany, Oregon. Recoveries from tabling placer samples were about 50 percent at grades of 30 percent titanium dioxide. Flotation was the most effective method for concentrating the fine ilmenite in clay samples; recoveries of approximately 50 30 percent titanium dioxide. Flotation was the most effective method for concentrating the fine ilmenite in clay samples; recoveries of approximately 50

Jan 1, 1961

By Herbert H. Einstein

Appendices A through M contain information that is the basis for many developments reported in the main text (Parts I through V); this information is, however, not needed in applying the research results. Specifically the appendices contain: A: Geology of Sampled Sites B: Comparison of Distribution Forms with Observed Trace Length Frequencies C: Joint Attitude Pole Diagrams D: Resistance and Deformability of Rock Discontinuities E: Resistance and Deformability of Joints - Details of Data Recording Procedure F: Documentation and Details for Simplified 2-Joint Wedge Analysis G: Generalization of the Stiffness Approach H: Inadequacy Due to Simplifying Assumptions in Wedge Analysis I: Rock Slope Reliability Analysis: State of the Art J: Resistance Derivations for Mechanical Model K: Supporting Derivations for Analysis Method DAYLITE L: Supporting Derivations for Simplified 2-Plane Reliability Analysis M: Plots of SLOPESIM Runs

Jan 1, 1979