Search Documents

By L. C. IlsLey

Permissible electric nine lamps are approved with the. understanding that if actively marketed they will be listed in Bureau of Mines publications so that state mine departments, compensation bureaus, mine operators, miners, and others interested in safety equipment for mines may know the permissible lamps available and the important safety features of each. The last list of permissible electric mine lamps was issued as Report of Investigations 33045 in June 1936, a supplement to Bulletin 332.6 All lamps described in Bulletin 332 are either obsolete or have been materially modified, as covered by extensions of the original approvals. These modified lamps and the new designs approved since 1930-totaling 12 cap lamps and 23 lamps of miscellaneous types-comprise the present list of actively marketed permissible electric mine lamps. This bulletin presents the Bureau's test requirements and procedure relative to permissible electric mine lamps and describes briefly the lamps, giving tabulated details of each.

Jan 1, 1942

Objective To reduce dust generated from soiled floors within enclosed operator cabs. Background Enclosed operator cabs are widely used on mobile excavation equipment in the mining and construction industries. They protect the operator from bad weather, noise, and airborne dusts. The inside cab environment usually must be kept at very low dust concentrations because of quartz dust generated from the excavation of silica-bearing rock. For cabs to be effective in controlling airborne respirable dust, they must have an efficient air filtration system, while providing a positive pressurization of the cab interior. Ideally, the recirculated and exterior makeup air filtration should provide at least 99% capture efficiency for dust particles as small as 0.3-µmaerodynamic diameters. Many of these enclosed cabs use heating units mounted or directed along the floor (see figure 1), which can cause dust entrainment problems. Prior studies by the National Institute for Occupational Safety and Health (NIOSH) of enclosed cabs have shown that these floor heaters can generate notable amounts of dust within the cab enclosure (see Technology News 486). Multiple-shift dust levels measured inside a drill cab increased on average from0.04 mg/m3 during the summer months to 0.68 mg/m3 during the winter months. Additional dust level measurements, made with optical particle counters during a nondrilling time period, verified that dust levels inside the cab increased from 0.03 to 0.26 mg/m3when the floor heater/fan was turned on. Dust levels within the cab also became greater than the ambient air dust levels outside of the cab when the floor heater was turned on during the nondrilling time period. This shows that the floor heater was a notable dust source problem. Cab floors are commonly soiled from operators tracking dirt inside the cab upon entering from the mine or construction site. Interior cab dust levels can be increased by (1) airflow disturbance of the soiled floor or (2) operator disturbance of the soiled floor. Approach During prior NIOSH surveys of surface coal mine drills, several drills with very low cab dust levels (#0.1 mg/m3) were observed to have floor sweeping compound spread out over the cab floor during the working shift. This initial observation led to a more controlled A-B study of the effect of the sweeping compound on the interior cab dust levels. This study involved dust sampling with and without sweeping compound inside the cabs of a bulldozer and two drills. Sweeping compounds commonly use sawdust or cellulose as the main bulk material, with oil or wax added for dust adhesion purposes. Sand is sometimes added to increase bulk density. Sweeping compounds with sand are commonly used to sweep up concrete floors. Those without sand (usually referred to as "gritless") are used to sweep up smooth finished floors. Most of the oils and waxes used for the adhesive ingredient are petroleum-base and can have an irritating odor. People sensitized to petroleum distillates could have allergic reactions to these sweeping compounds. A few companies offer non petroleum-base sweeping compounds, using either a natural oil or chemical additive for dust adhesion. During this study, it was decided that only the gritless sweeping compound (without sand) would be used, eliminating the addition of another potential silica source inside the cab. Since the sweeping compound would be applied on the enclosed cab floor for the duration of the shift, it was decided to use a canola oil-base sweeping compound to eliminate irritating odor from the petroleum-base sweeping compounds. The natural canola oil-base sweeping compound had a slight woody scent. The three pieces of equipment used in this study had notably different cab layouts. The bulldozer had a small cab with vents discharging air-conditioned or heated air from adjustable louvers at operator waist level and floor level. The bulldozer also had a cloth fabric seat and a carpeted floor. Drill A had a large cab with the heat directed from adjustable louvers at operator knee level and the air-conditioned air directed from cabin ceiling louvers. This drill had a vinyl fabric seat and a steel plate floor. Drill B had a small cabin with the heat directed across the floor (see figure 1) and the air-conditioned air directed down from the ceiling. It had a vinyl fabric seat and a worn rubber mat on a steel floor.

May 1, 2001

By T. L. Marchewka

As part of its program to conserve the Nation's natural resources by developing improved performance materials, the Bureau of Mines, U.S. Department of the Interior, in cooperation with the U.S. Department of Energy, has conducted an investigation of materials of construction able to withstand the high temperature and hostile environments encountered in coal gasification units. Refractory pipe liners are required when extremely hot gases or abrasive solids are transported between processing units in the gasification plants. One promising technique for producing refractory pipe (or refractory pipe liners) is centrifugal casting. For this study, the effect of processing variables such as workability, additives, reinforcement and spinning time, and centrifugal force were evaluated using four commercial refractory concretes. In addition, data on characteristics such as strength, density, abrasion, and spalling resistance of 5-inch-diam refractory pipe were developed. Techniques for forming large-diameter (19-inch) refractory pipe also were evaluated. The test results indicated that all four refractory concretes could be made into strong, homogeneous pipe, but that optimum casting parameters had to be determined for each specific composition. The investigation revealed that the major controlling factor in the production of the centrifugally cast pipe was the workability of the refractory concrete.

Jan 1, 1979

By K. O. Bennington

The thermodynamic properties of hedenbergite, of composition [(Ca0,9516) (Mg0,0583Fe2+0.7134 Fe3+0.0934 Mn0,1366) (Si206)], were experimentally determined at the Bureau of Mines. The standard enthalpy of formation determined by hydrofluoric acid solution calorimetry is AHf298 = -680.96±0.855 kcal/mol. The standard enthalpy of formation from the oxides is AR-96 = -24.55±0.485 kcal/mol. Low-temperature heat capacities were determined by adiabatic calorimetry from 12.3 to 300.1 K. The derived standard entropy is S-98 - 41.218±0.148 cal/mol-K. High-temperature heat capacities were measured with a differential scanning calorim¬eter from 397 to 1,147 K. These experimentally determined data were combined with data from the literature to calculate the Gibbs energies of formation and equilibrium constants of formation over the temperature range of measurements. Standard enthalpies of formation are given as a function of temperature. The standard Gibbs energy of formation at 298.15 K is AGf298 = -641.90±0.86 kcal/mol.

Jan 1, 1984

By H. W. St. Clair

This study was undertaken to provide a more adequate knowledge of the chemistry of the sulfide volatilization process for recovery of tin from low-grade Bolivian ores. The investigation was partly supported by the Department of State under its program for scientific cooperation with South American republics. The results of this investigation demonstrate the conditions under which cassiterite (Sn02) may be converted to stannous sulfide by reaction with pyrite or sulfur vapor, Quantitative data are given on the rate of sulfidization and on the vapor pressure of stannous sulfide.

Jan 1, 1954

By Seth C. Schaefer

The Federal Bureau of Mines studied the Gibbs free energies of formation of chromous fluoride (CrF2), chromic fluoride (CrF3), and chromium (II,III) fluorides (CrF2.40 and CrF2.45) with high-temperature galvanic cells employing calcium fluoride doped with 1 mole-pct yttrium fluoride as the electrolyte. Free-energy changes were obtained from open-circuit potential measurements for the following cells: Cr, CrF2 // CaF2 // NiF2, Ni (a) NiO, NiF2 // CaF2 // CrF3 , Cr203 (b) CrF2 , CrF2.40 // CaF2 // NiF2, Ni (c) and CrF2 ?45 , CrF3 // CaF2 // NiF2, Ni (d) with the following overall reactions Cr(s) + NiF2 (s) = Ni(s) + CrF2 (s) (1) 3NiO(s) + 2CrF3 (s) = 3NiF2 (s) + Cr203 (s) (2) 5CrF2 (s) + NiF2 (s) = 5CrF2.4O (s) + Ni(s) (3) and 3.64CrF2.45 + NiF2 (s) = 3.64CrF3 (s) + Ni (s) . (4) These results were combined with the best available literature values of ?Gf° of NiF2, NiO, and Cr203 to deduce Gibbs free energies of formation for the chromium fluorides expressed as follows: ?Gf°(CrF2) = -179.31 + 24.33 X 10-3T ± 0.43 kcal-mole. (5) (858.1 - 964.9 K) ?Gf° (CrF3) _ -226.16 + 1.82 X 10-3T ± 0.79 kcal/mole (6) (880.8 - 957.8 K) ?Gf°(CrF2.40) _ -213.65 + 32.14 X 10-3T ± 0.44 kcal/mole (7) (0053.9 - 936.8 K) and ?Gf°(CrF2.45) _ -176.17 - 12.67 X 10-3T ± 0.80 kcal/mole (8) (875.1 - 937.6 K). Free energies and equilibrium fluorine pressures for three univariant and one bivariant equilibria are illustrated.

Jan 1, 1976

By Lloyd Williams

1. This investigation shows that the Poplar Creek is the most important bed in Scott County from a production standpoint. Although the Poplar Creek bed contains the largest reserve, the Big Mary has a larger recoverable reserve. Estimates of reserves also have been made for the Pewee, Red Ash, Windrock, Upper Pioneer, Jellico, and White Oak beds. 2. Known measured and indicated reserves of coal, based on a minimum bed thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated to be 143 million tons as of January 1, 1954. Of this total, 74 million tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1956

By P. L. Sibrell

Previous research by the U.S. Bureau of Mines has shown that autoclave cyanide leaching of used automobile exhaust catalysts for recovery of platinum-group metals (PGM) is technically feasible. The purpose of this work was to investigate the chemistry of the dissolution of PGM in cyanide solutions in more detail. Where possible, samples of pure, elemental PGM powders or foils were used instead of automobile exhaust catalysts, because of their greater purity. Ultraviolet spectra revealed that Pt and Pd were solubilized as the square planar tetracyanometallate (II) complexes, while Rh was solubilized as the octahedral hexacyanorhodate (III) complex. This explained the poor recovery of Rh from solution by carbon adsorption, solvent extraction, and ion exchange observed in earlier research, because of the higher anionic charge and size of the octahedral complex. Leaching rate studies showed that the rate of solubilization was greatest for Pd, followed by Pt and Rh. Although the rate of chemical reaction was the controlling step for the dissolution of elemental Pt and Rh samples, the rate of pore diffusion was rate limiting for PGM in catalyst samples.

Jan 1, 2010

By J. R. Nettle

A method has been developed in the laboratory for successfully electro-refining titanium metal. Refining is accomplished in e fused-salt electrolyte using offgrade metal as the anode and collecting the purified metal at the cathode. The characteristics and requirements of the various alkali chlorides tested as electrolytes are discussed in relation to relative ease of purification and serviceability. The various types of cells designed and tested for electrorefining are illustrated and their method of operation discussed. The individual advantage of each cell and the purpose for which it was designed are reviewed. The magnitude of the cathode current density was found to depend largely upon the quantity of soluble titanium chloride in the electrolyte. The physical condition of the anode also greatly affected the cathode current density.

Jan 1, 1957

By James A. Powell

The theory of electromagnetic fields indicates such fields could be used to detect and locate trapped miners. To be useful, the hardware of the system must meet a number of requirements, including small size, intrinsic safety, and rugged construction. Such hardware has been built, and the system has been tested by the Bureau of Mines and its contractors. These tests indicate that the electromagnetic method provides a practical means to locate miners in emergencies.

Jan 1, 1976

By E. W. Dean

This report on the physical and chemical properties of typical crude oils of Oklahoma is the sixth in a series of preliminary chapters of a bulletin covering the producing districts of the United. States. Preceding reports* may be obtained on request. The details of the methods used in this survey in collecting samples, making laboratory tests, and interpreting results are discussed in the first three papers. If any errors or omissions are noted by readers, it is hoped they will be brought to the attention of the Bureau of Mines for correction before the appearance of the permanent report. Samples of Oklahoma crudes analyzed in this report were taken from those fields representing the major production of the State. The Oklahoma Geological Survey designates 172 different oil and gas fields in the State, S1 being in Osage County, 14 in Tulsa County, 14 in Okmulgee County, 9 in Washington County. The list of samples collected by the Bureau of Mines represents only 5 fields in Osage County - Bigheart, Burbank, Hominy, Osage Junction, and Pershing - yet these samples, together with those from adjoining fields, are representative of nearly all crude produced in the county. The sample 'from the Pershing field, for example, is representative of the crude produced in several fields in that part of the county - such as Nelagoney, Pawhuska, Wyomona - and the sample from the Skiatook,

Jan 1, 1922

By M. M. Fine

Chalcocite flotation concentrates (26-34 percent Cu and 6-7 percent S) were roasted in air to determine sulfur elimination as a function of temperature, airflow rate, and residence time. Fluosolids roasting was evaluated batchwise and continuously in a 4-inch fluid-bed reactor. Kiln roasting tests were carried out in a 4-inch ID by 6-inch-long rotary drum. Pelletizing the very fine concentrates prior to roasting was essential to minimize dust losses and accretions. Concentrate pellets, sized minus 10 plus 20 mesh and bonded with 2 percent bentonite, were excellent feed for fluosol¬ids roasting and limited dust losses to 10 percent or less. One-fourth-inch pellets were best suited to kiln roasting. Both techniques were capable of producing copper calcines analyzing well under 1 percent residual sulfur when operated at 900° C with average retention times of 3 to 4 hours. Calcined pellets were strong, porous, and readily reducible.

Jan 1, 1970

By O. C. Blade

This report on the properties of motor fuels sold through service stations in the United States was made in accordance with a cooperative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. This paper i8 a continuation of a series made in cooperation with the Coordinating Fuel Research (CFR) Committee of the Coordinating Research Council (CRC), Inc. The first of this series of reports presented data on motor gasolines sold during the winter of 1935-36, and succeeding reports described motor gasolines Bold during the summers and winters to and including the summer of 1941 Y. No reports were made on motor gasolines sold during the winter of 1941-42 and during the summer of 1942. However, starting with the winter of 1942-43, the semiannual reports were resumed.

Jan 1, 1951

By Herbert H. Einstein

Appendices A through M contain information that is the basis for many developments reported in the main text (Parts I through V); this information is, however, not needed in applying the research results. Specifically the appendices contain: A: Geology of Sampled Sites B: Comparison of Distribution Forms with Observed Trace Length Frequencies C: Joint Attitude Pole Diagrams D: Resistance and Deformability of Rock Discontinuities E: Resistance and Deformability of Joints - Details of Data Recording Procedure F: Documentation and Details for Simplified 2-Joint Wedge Analysis G: Generalization of the Stiffness Approach H: Inadequacy Due to Simplifying Assumptions in Wedge Analysis I: Rock Slope Reliability Analysis: State of the Art J: Resistance Derivations for Mechanical Model K: Supporting Derivations for Analysis Method DAYLITE L: Supporting Derivations for Simplified 2-Plane Reliability Analysis M: Plots of SLOPESIM Runs

Jan 1, 1979

By W. A. Selvig

[THE BUREAU OF MINES receives many requests for information regarding the low-temperature carbonization properties of American coals. This report presents in collected form the results of Fischer-Schrader bench-scale, low-temperature carbonization assays at 500° C. made by the Chemistry and Physics Section at the Pittsburgh station of the Bureau of Mines. Most of the assays were made of coals tested in connection with a survey of gas and coke-making properties of American coals,4 which was started in 1928 by the Bureau in cooperation with the American Gas Association. Other coals were assayed in connection with miscellaneous investigations. Since 1930 about 400 samples of coal were assayed from nearly every coal-producing State, Alaska, and British Columbia, Canada. The results of the tests on about two-thirds of the coals are scattered through more than 50 separate publications. This paper summarizes the data in the published reports as well as all unpublished data obtained to January 1, 1956. The report also includes a detailed description of the procedure used in making the assay.]

Jan 1, 1957

By L. E. Schultze

As part of the Bureau of Mines research program on recovering alumina from domestic resources, methods for extracting iron from aluminum sulfate solutions (obtained by leaching kaolinitic clay with dilute sulfuric ,acid) were investigated. In countercurrent extraction experiments at a l-gal/hr flow rate of aluminum sulfate leach liquor, the iron concentration 'was decreased from 1.4 g/l to 0.01 g/l after four stages of using a primary amine extractant. The iron-loaded amine solution was regenerated in five stages using 3[N] sulfuric acid or in four stages using 6[N] sulfuric acid. The aluminum sulfate solution obtained was suitable for the preparation of alumina meeting cell-grade standards of less than 0.01 pct iron.

Jan 1, 1979

By A. J. Barry

A method was developed for testing the anchorages obtained with 3/4-inch, expansion-type, headed bolt and shell assemblies. The apparatus is a modification of that used in testing -inch-diameter, slotted-type bolts. Four makes of expansion-type shells were used in 64 tests made in sandstone and shale roof. The results show that for 3 makes of shells the anchorage effectiveness is independent of the installed land, and for the fourth make of shell a better anchorage is obtained when instilled at a load of 8,000 pounds. The results also show that deformation of the expansion plug influences the majority of the anchorages obtained with two makes of shells. This deformation causes a larger increase in displacement for a given added increment of load. The data from 48 of the 64 tests were combined to establish a relationship between average displacement and increase in bolt load (above the installed load). This relationship can be used to evaluate the anchorage effectiveness of any 3/4-inch-diameter, expansion-type, headed bolt and shell assembly tested in the field.

Jan 1, 1956

By E. C. Lane

This paper on the physical and chemical properties of crude oils from California fields is one of a series of reports on the oil-producing districts of the United States. The paper includes a short discussion of results, tabular data, and individual analyses of 16 California crude oils. Analyses of other oil from California have been published in Reports of Investigations 25954/, 26085/, 28466/, and 30747/. The samples were obtained by members of the San Francisco office of the Bureau of Mines. The collecting of the samples vas facilitated by the courtesy of representatives of oil companies in California.

Jan 1, 1937

By E. C. Lane

This paper on the physical and chemical properties of crude oils from California fields is one of a series of reports on the oil-producing districts of the United States. The paper includes a short discussion of results, tabular data, and individual analyses of 16 California crude oils. Analyses of other oil from California have been published in Reports of Investigations 25954/, 26085/ 28466/, and 30747/. The samples were obtained by members of the San Francisco office of the Bureau of Mines. The collecting of the samples vas facilitated by the courtesy of representatives of oil companies in California.

Jan 1, 1937

By John Nagy

A study was made in the Bureau of Mines experimental coal mine of factors affecting gas ignition by a cutoff explosive charge. Experiments showed that, although gas could be ignited under some circumstances, the probability under normal mining conditions would be low. The use of permissible explosives, relatively short-delay intervals in firing adjacent holes, blasting to a 6-inch kerf, and reasonable care in the placement of the holes favor safe blasting and are current practice in mining. The experiments also showed that the weight of the charge is not a primary factor in the ignition of gas by a cutoff charge. The quenching action of a first charge on the igniting action of a second was verified in a supplementary study. Related experiments have shown that gas at the face may be ignited by a single charge of explosive when fired with a light coal burden. Permissible explosives were less hazardous under these conditions than nonpermissible explosives. The frequency of gas ignition in cutoff and single-charge experiments increased as the linear distance between the sheared face and the opposing mine rib increased.

Jan 1, 1960