Search Documents

By E. J. Murphy, A. P. Rowles, John C. Holtz

"INTRODUCTION The use of sheaths or hollow cylinders of flame-extinctive materials surrounding cartridges of permissible explosives has been developed during the last few years; the history of sheathed explosives in their salient development in Belgium was treated recently in a publication of the Bureau of Mines. 6/ This development is of great interest in explosives technology, for it holds possibilities of reducing further the ignition hazards that may cause many coal-mine disasters. The township interest in sheathed explosives in this country is attested by the passage of some State laws permitting the use of such explosives on shift 7/; inquiries are received in increasing numbers concerning the effects of sheaths on practical hazards as well as the general technology underlying their use."

May 1, 1943

By J. C. Hartley

The most important single operation in mining is the ventilation of underground areas in a manner conducive to the health and safety of employees. Adequate volumes of pure air must be supplied at the working faces, along the haulageways, and wherever men work, so as to dilute and carry away the methane liberated from the coal and adjoining strata, noxious gases evolved by the use of explosives, and the carbon dioxide exhaled by men and formed by oxidation of carbonaceous material, as well as any other gases, and also dusts which may be found in mine workings. A sufficient quantity of air must also sweep abandoned or worked-out areas of the mine to prevent the accumulation of gases, where sealing methods are not utilized to isolate old workings. Air, in a quantity adequate to meet the needs of the particular mine to which it is applied, is necessary, and supplying it can be made very expensive through failure to observe good practices in its direction and apportionment." Leaky stoppings, doors, and overcasts rob the working faces of air and add to the ventilating cost by burdening the fans with fugitive air,

Jan 1, 1944

By W. P. Diamond, B. M. Bench, C. M. McCulloch

Coalbeds exhibit a directional permeability, with the maximum permeability oriented parallel to the face cleat. Thus, the most efficient pattern of vertical degasification holes for a coalbed is dependent upon cleat orientation. Surface joints, infrared photolinears, and Ronchi grating photolinears were investigated as potential estimators of subsurface cleat orientation. Cleat orientations were masured in 18 mines, in the Pittsburgh coalbed in southwestern Pennsylvania and northern West Virginia to be used as a standard against which prediction techniques would be evaluated. Two cleat systems with a strong geographic segregation were measured in the study area: N 67° W - N 28° E (95° separation) for the north, and N 76° W - N 17° E (93° separation) for the south. Directional data obtained from the three techniques investigated yielded satisfactory regional predictions of cleat orientation. Analysis of surface joints was the only technique considered sufficiently reliable on a local basis. Prediction of cleat orientation is based on the pairing of the principal directional sets into all reasonable combinations of fundamental systems. The system or systems composed of the most dominant sets nearest to 90° separation are likely to be a reliable prediction of cleat orientation. The most dominant set of the system selected is likely to be the face cleat.

Jan 1, 1976

By H. F. Feldmann

This work was done to provide thermodynamic, electrical, physical, and compositional data on the seeded combustion plasmas of seven coals for the design of MHD generators. The systems were assumed to be at equilibrium, and the design data were generated by solving for the composition of both gas and liquid phases with a digital computer. The coals reported in this study include a western subbituminous, a Pennsylvania anthracite, and five representative bituminous coals. The data include dewpoint temperatures of both slag and seed. A Mollier diagram for each coal is given to allow graphical generator calculations.

Jan 1, 1970

By Jr. Driscoll

The thermoelectric properties of yttrium monoarsenide, yttrium monoanti-monide) and ternary materials from the Y-As-Se and Y-Sb-Te systems were investigated by the Bureau of Mines from room temperature to 1,000° C. The maximum calculated figure of merit for yttrium monoarsenide and yttrium monoantimonide was 2 x 10-5 ° C-1. YAs and YSb were semimetallic conductors with low Seebeck coefficients and electrical resistivities. The values of the Seebeck coefficient and electrical resistivity of the Y-As-Se and Y-Sb-Te materials were between those of the yttrium selenides and tellurides and of YAs and YSb, respectively. The maximum power factor calculated for the Y-As-Se materials was 2 X 10-5 watt/cm ° C2 which yielded an estimated figure of merit of 6 X 10-4 0 C-1. Most of the Y-As-Se compounds had high Seebeck coefficients and moderately low electrical resistivities. The Y-Sb-Te materials were degenerate semiconductors with power factors of 6 X 10-8 watt/cm ° C2.

Jan 1, 1967

By T. F. Tomb

Past experience has shown that the penetration characteristics of the 10-mm nylon cyclone used on approved personal sampling equipment are significantly different from those determined in the laboratory using a nonpulsating flow source. The Bureau of Mines has developed and recommended a modification to presently approved equipment that will alleviate this difference. However, as a result of this modification, a new relationship for converting respirable dust concentrations measured with approved personal sampling equipment to equivalent concentrations as measured with an MRE instrument will have to be established. This Bureau of Mines report describes the underground sampling program conducted to establish a new factor for converting respirable dust concentrations measured with personal sampling equipment, modified with a recommended pulsation damping device, to an equivalent concentration as measured with an MRE gravimetric dust sampler.

Jan 1, 1973

By Albert W. Deurbrouck

Twelve samples from six Barbour County coal beds were analyzed for this report. The samples collected were generally high sulfur content coals, frequently exceeding 3 percent in the raw-coal sample. Many of them could not be upgraded to acceptable metallurgical standards even by rigorous preparation procedures. The production of coal in the county in 1963 amounted to almost 3 million tons of which 44 percent was mechanically cleaned.

Jan 1, 1965

By X. C. Shi

Bacterial mutagenicity and mammalian cell chromosomal and DNA damage in vitro assays were performed on a diesel exhaust particulate material (DPM) standard in two preparations: as an organic solvent extract, and as an aqueous dispersion in a simulated pulmonary surfactant. U.S. National Institute for Standards and Technology DPM SRM 2975 expressed mutagenic activity in the Salmonella reversion assay, and for in vitro genotoxicity to mammalian cells as micronucleus induction and as DNA damage in both preparations: as an acetone extract of the DPM mixed into dimethylsulfoxide, and as a mixture of whole DPM in a dispersion of dipalmitoyl phosphatidyl choline. Dispersion in surfactant was used to model the conditioning of DPM depositing on the deep respiratory airways of the lung. DPM solid residue after acetone extraction was inactive when assayed as a surfactant dispersion in the micronucleus induction assay, as was surfactant dispersion of a respirable particulate carbon black. In general, a given mass of the DPM in surfactant dispersion expressed greater activity than the solvent extract of an equal mass of DPM.

Jan 1, 2009

By C. E. Coleman, Joseph D. Davis

During some distillation experiments conducted by the Bureau of Mines in cooperation with the Trent Process Corporation it was observed that amalgams of heavy petroleum oils and finely pulverized coal tended to produce a denser coke than that obtainable from the coal when retorted alone . Even anthracite coal when retorted with oil yielded a coke . This led the writers to believe that by mixing a lowrank coal ( sub-bituminous or even lignite ) - with asphaltic oil and retorting it, a coke suitable for domestic fuel could be made . Thus there was contemplated the production of domestic coke and the utilization of a low- grade oil in one operation . - In order to decide on the practicability of this process , it was necessary to know the value of products obtainable by such a method , as compared with those obtained by separate distillation . A laboratory method was therefore devised , and while it was realized that no small - scale testing apparatus for destructive distillation gives results that are directly applicable to commercial - scale operations , by keeping distillation conditions uniform for comparative tests , results were obtained valuable for purposes of comparison . The plan was to distill mixtures of coal and oil in a laboratory retort , and then distill the constituents separately under the same conditions . The comparative quantities of products yielded were thus directly obtained , and their quality was determined by analysis . The following are the main points investigated : ( 1 ) Quantity and quality of coke ; ( 2 ) Quantity of oils boiling below 221 °C . ( gasoline stock) and oils boiling at 221 to 300° C . ( kerosene stock) ; and ( 3) Quantity and quality of gases .

Jan 1, 1922

By Robert K. Guthrie, James W. Amyx, D. B. Taliaferro

"INTRODUCTION Secondary recovery of oil by water-flooding is practiced more extensively in North Texas than in any other section of the State, and the progress and experience of the operations in that area are of continuing interest to all branches of the oil industry. The first Bureau of Mines report on water flooding in North Texas 7/ chronicled the activities from December 7, 193f', when the Railroad Commission of Texas granted The Texas Co. the first permit to inject water into an oil-bearing sand, through 1944. This second report has been prepared as a supplement to Report of Investigations 3906 to show the progress and expansion of water-flooding. The format of this report is almost identical with what of report of Investigations 3906, except for a few miner changes. For the sake of brevity, certain basic information contained on the first report has not been repealed, and the reader is urged to consider the two reports as corporation writings.The North Texas area, as encompassed by the two reports, corresponds Railroad Commission of Texas Districts 7P and 9. Oil-development operations in the two districts, since oil was discovered in 1904, have resulted in the recovery of approximately 1,400,000,000 barrels of oil from a proved area that has been estimated to exceed 413,000 acres. During October barrels of oil was produces by primary and secondary-recovery methods from 1,746 flowing wells and 25,211 pumping wells, a daily average 6.6 barrels per well. Of this total volume of oil recovered in October 1947, 47,965 barrels (0.87 percent) was recovered from leases on which water-flooding operations were in progresses."

Feb 1, 1948

The panic bars (and associated linkages and electrical circuitry) that are defined in this document are a machine operator-actuated control for the emergency deenergization of the tram motors on self-propelled, electric and diesel face equipment; including haulage equipment such as shuttle cars. There are nine basic types of panic bars (and several variations) that are recommended in this document, but all of the panic bars are characteristically of the "fire door" type that is frequently encountered on outside exit doors of many public and some commercial buildings. It is also the intent of the following panic bar designs that, when emergency brakes are added to the face equipment machinery for which they are required, that they be designed and hooked up so that actuation of the panic bar will result in automatic application of the emergency brakes (immediately following the deenergization of the tram motors). The following panic bar design requirements are a restatement of the proposed requirements defined in the Federal Register, requirements cited in 'Guidelines for the Design and Installation of Devices for Deenergization of Self-Propelled Electric Face Equipment/ Automatic Emergency Brakes" by C. E. Lester and J. D. Greenhalgh of MESA, and Bendix recommendations that were formulated as a result of discussions with personnel at the various machine manufacturers and underground coal mines that we surveyed, discussions with G. L. Judy (our consultant), etc:

Jan 1, 1974

By R. F. Stewart

A nuclear meter based on measurement of prompt capture gamma rays is being developed for monitoring the sulfur content of coal streams. Equipment has been built to measure sulfur rapidly, and methods have been devised to compensate for changes in moisture, ash, and bulk density of coal flowing through a bin. Pilot plant tests of the system with various additives to different coals show a precision and accuracy of 0.02 percent sulfur and 0.04 percent sulfur, respectively. Based on these results, a hardwired meter has been fabricated for testing in a commercial coal preparation plant.

Jan 1, 1974

By J. W. Town

The Bureau of Mines made continuous-circuit beneficiation studies to determine the optimum conditions for concentrating phosphate minerals from the intermediate-and marginal-grade ores of the Phosphoria Formation in southeast Idaho. Intermediate-grade ore was represented by a sample from Georgetown Canyon and marginal-grade ore from the Gay mine near Fort Hall. Two flow-sheets were developed: The first involved roasting, attrition scrubbing, sizing to remove a concentrate, grinding of the oversize, des liming, and flotation; in the other flowsheet roasting was eliminated. Controlled attrition scrubbing was used to remove clay and silt-size quartz particles imbedded in the phosphate pellets without breaking the pellets. The minus 35-plus 200-mesh fraction was removed by sizing as a finished acid-grade concentrate. The plus 35-mesh material was ground in a rodmill to minus 35 mesh and recycled to the attrition scrubber. The minus 200-mesh fraction was des limed at about 800 mesh to remove clay slimes and floated with 3 to 4 pounds of emulsion per ton of feed. The aqueous fatty-acid oil emulsion consisted by weight of 3 parts No.2 diesel oil, 3 parts crude tall oil, and 0.5 part water-soluble petroleum sulfonate.

Jan 1, 1967

By Bernard Porter

The densities of LiF, NaF, and KF, of binary mixtures of these alkali fluorides, and of binary mixtures of UF4, ThF4, YF3, LaF3, and CeF with each of tie alkali fluorides were measured as functions of the melt composition and temperature. Molar volumes at 1,000° C were calculated for all the mixtures. Binary systems containing LiF exhibited molar volume ideality. Binary fluoride systems containing either NaF or KF as the alkali fluoride exhibit positive deviations from molar volume additivity. However, molar volumes in the NaF-KF system are ideal.

Jan 1, 1966

By O. C. Blade

This report on the properties of motor fuels sold through service stations in the United states was made in accordance with a cooperative agreement between the American Petroleum Institute and the Bureau of Mines of the United states Department of the Interior. This paper is a continuation of a series made in cooperation with the Coordinating Fuel Research (CFR) Committee of the Coordinating Research Council (CRC). Inc. The first of this series of reports presented data on motor gasolines sold during the winter of 1935-36, and succeeding reports described motor gasolines sold during the summers and winters to and including the summer of 1941. No reports were made on motor gasolines sold during the winter of 1941-42 and during the summer of 1942. However, starting with the winter of 1942-431' the semiannual reports were resumed.

Jan 1, 1950

By J. Mutmansky, C. Lee

"The size distribution of coal mine dust is one of its most important characteristics because the particle size is known to govern the region of deposition of dust within the human respiratory tract. In addition, dust characteristics, particle settling rate, transportability of the dust and the efficiency of dust control measures are all affected by the particle size. As a result, particle size distribution of the airborne dust in a coal mine is a fundamental property that impacts on the health of underground workers.This paper deals with some basic findings on the size distribution of cool mine dust based upon the results of data collection in six underground coal mines using continuous miners. All airborne dust sampling was performed on development sections using eight stage cascade impactors and permissible 2. O l / min pumps. Samplers locations were fixed in the sections with respect to the continuous miner and roofbolter or with respect to the intake and return airways • Sampling times varied from 45 minutes to 6 hours , depending upon the dust concentration. The first topic of analysis was the test to determine whether the commonly used lognonnal distribution is valid when applied to airborne coal mine dust. Secondly, the conventional method of representing the· distribution using two parameters, the geometric mean and the geometric standard deviation, is questioned. Since almost all size data were found to show some degree of bimodality, the two parameter lognonnal distribution may not represent the total airborne coal mine dust size , quite adequately. Bimodal lognonnal distribution was tested to be a good approximation in the case with two modes in the size distribution.The final topic discussed in this paper is the 'locational variation of the airborne dust size distributions within the continuous mining section. The size distributions varied considerably at the different sampling locations with the continuous miner and roofbolter producing the coarser distributions. Fine size modes in the range of 2 to 4µ m including mostly respirable dust particles were present in almost all samples • Second dust generating sources such as the shuttle car movement were found to be major causes of high respirable dust concentrations in some cases ."

Jan 1, 1988

By James R. Coldwell

Mining and processing cost analyses were conducted by the U.S. Bureau of Mines on massive sulfide copper-zinc and low sulfide vein gold deposit types that may be found in the Ketchikan Mining District. Reserves and recoverable metal values (RMV) needed to make these deposits economically viable were modeled. Methods for estimating ore grades and required RMV are presented. Economic modeling for massive sulfide deposits indicated the RMV necessary for a 15% Discounted Cash-Flow Rate-Of-Return (DCFROR) for an underground cut-and-fill mine ranged from $137/mt for a 6,100 mtpd on-site milling operation to $526/mt for a 450 mtpd off-site milling operation. On-site milling was always less costly than off-site milling. Economic modeling for low sulfide vein gold deposits indicated the RMV necessary for a 15% DCFROR for an open-pit mine, off-site mining operation ranged from $S4/mt at 2,900 mtpd to $71/mt at 360 mtpd, and from $49/mt at 2,900 mtpd to $100/mt at 360 mtpd for an on-site milling operation. Off-site milling was less costly than on-site milling until production exceeded approximately 1,700 mtpd. Then, economies of scale reduced operating costs enough to offset the higher capital costs required for on-site milling.

Jan 1, 1995

By S. J. Gasior

A method for destroying the caking properties of bituminous coal was developed by the Bureau of Mines. Coal is treated in a fixed bed by heating through its plastic range under controlled temperatures in mildly oxidative atmospheres composed of inert gas and/or steam containing about 1 volume-percent oxygen. High-volatile A (hvab) and high-volatile B (hvbb) and low-volatile bituminous (lvb) coals in the size range 1/8 to 1-1/2 inches were successfully treated at 0 (atmospheric pressure) to 300 psig in static beds 6 to 18 inches deep. Conditions of treatment depended on the coal and ranged from 80 to 200 minutes at 350° to 510° C. Char produced in this manner from hvab coal was gasified with steam at 800° C and 100 psig in a fixed bed in one series of tests and in other tests was exposed to hydrogen in a dilute co current free-falling-bed system at 750° C and 3,000 psig without agglomerating.

Jan 1, 1965

By Robert W. Freedman

In the Bureau of Mines study, a filter with a 20-by 20-inch-square cross section was inserted into the exhaust ducting of a 4-stroke-cycle, 90-hp diesel engine, and the efficiency of removal of total particulate was measured gravimetrically as a function of time. Removal efficiencies were close to 90 pct during the main portion of several extended runs employing several combinations of filter beds. Variations in engine load had little effect on collection efficiency. Particle size as measured by a Bureau-developed online instrument centered on 0.07 m based on number count. Removal efficiency increased rather sharply for both larger and smaller particles.

Jan 1, 1979

By John C. Edwards

A computer program, developed for the Bureau of Mines under contract, predicts in a quasi-steady-state approximation the ventilation and contaminant concentrations and temperatures when a fire occurs in a multi-level mine. For periods of time in which there is no significant change in the ventilation, yet a fire is producing fumes, a real-time fume concentration throughout the mine is calculated. Multiple and time-variable contaminant sources can be simulated. Recirculation paths that can develop provide a mechanism for increasing the fume concentration in the mine network and are identified by the computer program. This report contains a listing of the Fortran computer program as well as the required format of the input data. Two examples are provided of the real-time spread of smoke from a fuel-rich fire throughout a multilevel mine. The first example considers an operational exhaust fan as well as a booster fan. The second example evaluates the real-time smoke spread following a failure in the exhaust fan; recirculation occurs in this latter case.

Jan 1, 1982