Search Documents

By S. H. Ash

California leads the Nation in the number of operating metal mines and the small number of persons employed at individual mines, which reached a minimum irk 1932 with an average of seven men. The mines are scattered over the entire State, which is the second largest in area (155,562 square miles) in the United States. The mines are situated at various altitudes, with portals ranging from approximately 300 feet below sea level to almost 12,000 feet above. Many of the mines can be reached only during the summer, while at others the heat of the regions adds so the difficulties during the summer months Supplied of explosives the use (or, probably more correctly, the misuse) of which constitutes one of California's gravest mining problems; are handled and stored under condition that contribute many hazards. The problem of providing medical care is serious and complicated, especially at small mines and more particularly in the almost inaccessible mountainous regions; instances in which a knowledge of first aid would have been beneficial but was lacking, or when first aid was instrumental in saving life or limb because it was available are too numerous to be mentioned.

Jan 1, 1936

By Elton L. Litchfield, Milton L. Weiss

Studies were made on the projectile impact sensitivity of explosives by subjecting explosive samples to the impact of metal projectiles fired from a 0.50- caliber gun . The projectiles , in the form of right cylinders , made plane surface to plane surface contact with the explosives . Pressures in the explosive were investigated with an expendable pressure transducer in some instances . The physical model of the projectile - explosive interaction describes , in principle , the duration of the peak shock pressure in terms of the projectile and explosive geometry and the steady- state penetration of the explosive . Of the explosives studied , liquid hydrogen- solid oxygen and liquid oxygen - solid or liquid hydrocarbon fuel were the most shock sensitive ( requiring an initiating shock of about 1.0 kb or 987 atmospheres pressure ) ; cast TNT was the least sensitive ( requiring an initiating shock of more than 110 kb pressure ) . Measurements of pressure in the explosive showed some moderate space resolution by the transducer and gave pressure distributions in agreement with expectations from the model of the shock processes . The appearance of the recovered projectiles and the calculated initiation shock pressures suggest that the solid explosives were initiated directly to high- order detonation , whereas the liquid explosives were probably initiated to low- order detonation-- with a subsequent , later transition to high- order detonation .

Jan 1, 1965

By D. S. DeLong, A. Giza, D. G. Fraser, V. A. Robinson, T. B. Whitmoyer, J. E. Sneckenberger

"A cotton dust animal exposure system has been modified to incorporate a microcomputer feedback loop to monitor particle concentrations. The loop's major components are a minature real-time aerosol monitor (miniram) to estimate concentrations and a microcomputer to read the miniram's data and to control a stepper motor that adjusts the amount of dilutant air mixing with respirable cotton dust. Ninety minute trials of this system indicate that the standard deviation of particle concentrations is within 0.68 Mg/m3 of the average concentration, insuring a near constant concentration of respirable dust throughout the exposure.INTRODUCTION Previous workWeyel et al. (1984) have determined that respirable cotton dust can be shaken from bulk cotton samples using acoustical energy. The particle generator designed to utilize this fact operates like a commercially available sonic sifter, but on a much larger scale.While this generator successfully resuspended trapped respirable cotton dust, the generator output concentration decreased exponentially with time. This disadvantage was solved by Frazer et al. (1986) by operating the generator with a sinusoidal voltage near the minimum resonance frequency of the generator. This adjustment enabled the generator to produce respirable cotton dust for six hours or longer.Frazer et al. (1987) utilized the modified acoustical generator to produce a cotton dust animal exposure system. The cotton dust concentrations were estimated by a miniram, a light scattering aerosol Monitor. The system operator used the miniram values to adjust the system's parameters to maintain the desired concentration level.PurposeThe objective of this study was to introduce a computerized feedback loop to the operator controlled cotton dust animal exposure system. The miniram's estimates were analyzed by a microcomputer to determine what adjustments in the flow of dilutant air were necessary to maintain the desired cotton dust concentration. These modifications were intended to improve system performance and ease the system operator's work burden."

Jan 1, 1988

As a basis for recommendation and for instruction of bureau engineers the considered opinion of the bureau is expressed in "decisions" of its Mine Safety Board, approved by the Director. Ten of these decisions were discussed, in Information Circular 6091.3 Decision No. 11, approved by Scott Turner, Director, on February 28, 1929, is as follows: "In the interest of safety, the Bureau of Mines, Department of. Commerce, recommends that in coal mines, haulage and (or) hoisting be kept in intake air as far as possible." As in the case of previous mine-safety decisions, the subject matter covered by this decision has frequently come to the attention of the Bureau of Mines through the reports of its mining engineers on explosion disasters and in accident-hazard investigations.

Jan 1, 1929

By Peter F. Steidl

Seven degasification wells have been completed in the Pittsburgh coalbed at the new Emerald mine near Waynesburg, Pa. Funding was provided by the Bureau of Mines to perform stimulation treatments on five of the wells, to show that this is a feasible and economical means of degasifying part of a coalbed. The seven wells ranged in depth from 590 to 910 feet. Stimulation treatments used 25,260 to 42,660 gallons of foam and 7,400 to 12,800 pounds of 20/40-mesh prop sand. Pumping rates were 10.8 to 11.6 bbl/min and treating pressures were from 1,050 to 1,600 psig. On the day following stimulation, gas production ranged from a few hundred cubic feet per day to more than 100,000 cu ft/day.

Jan 1, 1978

The Bureau of Mines has reviewed those portions of the "Tariff Schedules of the United States Annotated 1963" that are of interest to the minerals industry. This study shows to what extent rates of duty were altered (increased or decreased), and provides a bridge where possible from the old Schedule A classification sys tem to the new TSUS system of statistical reporting of import data. In general the new tariff has corrected previous classification defects and inconsistencies, but the rates of duties have not been materially changed.

Jan 1, 1965

To improve the ventilation of large-opening under-ground stone mines by using stoppings made from stone left in place. Background Underground stone mines typically use large room-and-pillar openings with little ventilation control. Stone miners may be exposed to contaminants that include silica dust, diesel particulate matter (DPM), exhaust gases, nuisance dust, and face shot (blasting) fume gases. The health risks from breathing these fine particles and toxic organic materials are well documented. Although contaminants such as dust or diesel exhaust can be some-what controlled at the source, the escaping contaminants are often diluted and removed from work areas using ventilation with minimal controls. In many cases, current mine ventilation practices use trial-and-error techniques to improve ventilation. The growing realization of the importance of a healthy work environment along with increased regulations will require many stone mines to implement new ways to improve ventilation. In-place stone stoppings are one option. Mine air flows from one point to another because of a pressure differential between those points. This pressure differential is established using a mechanical fan in conjunction with separations (stoppings) between high-pressure (intake) and low-pressure (return) airways. The separation of intakes and returns is an important concept that is used in most other types of mines. Normally, air moves through underground stone mines with minimal control technology. Fans are placed in locations where they are thought to be most beneficial, and intakes are not separated from returns. In a few smaller underground stone mines, proper ventilation can be achieved with a few strategically placed fans. However, as these mines increase in size, moving adequate quantities of air through-out the mine becomes harder, and separation of intakes and returns becomes a problem. Building traditional mine stoppings to separate the intake and return airways in entries with a cross-section area often exceeding 800 ft2 is difficult. The stoppings must be able to withstand both the dynamic pressure from face shots and the static pressures created by the fans. Construction and maintenance difficulties, as well as high costs, are the main factors preventing these traditional mine stoppings from gaining wide acceptance by the stone mining industry.

Dec 1, 2002

By N. O. Johnson

This is one of a series of-Information Circulars dealing with mining and milling methods and costs at mines in various districts in the United States. The Hog Mountain gold mining district is of the northern edge of Tallapoosa County, in the east central part of the State of Alabama. The district is equally close to Goodwater and to Alexander City, both stations on the main line of the Central of Georgia Railroad. From Alexander City the mine is reached by 13 miles of graded road, traveling in a northeast direction. In dry seasons the road is good; in wet weather it is bad but passable. Improvements are being made constantly on the road, so that in the near future the gravel road should be good under all weathered conditions.

Jan 1, 1936

By C. A. Herbert

Information Circular 6746 reviewed the fatalities in Indiana coal mines. for the fiscal year October 1, 1951 to September 30, 1933. Since then Indiana has changed its fiscal year to the period July 1 to June 30, but as most statistical data on accidents are arranged according to calendar years, the data in this paper are for the last 3 months of 1932 and the calendar year 1933, rather than for the new Indiana fiscal year. Tables 1 and 2 list the fatalities in Indiana coal mines3/ by cause and occupation for the last 3 months of 1932 and for the calendar year 1933. The fatalities for the small wagon mines employing fewer than 10 men are separated from those employing 10 or more men to call attention to the ex- tremely high fatality rate in small mines, largely because the State mining law does not apply to them nor do they come under the jurisdiction of the Indiana mine inspectors; as a result health and safety conditions are ex- tremely bad. During the last 3 months of 1932, 5 (approximately 42 percent of the total) fatalities occurred in the small mines, while for the calendar year 1933, 12 (approximately 32 percent) of the fatalities occurred in them. The Indiana Division of Mines and Kining estimates that these small mines have an annual production of approximately 325,000 tons, or about 4.5 percent of the total coal-mine production of the State. In other words, for these small mines the fatality rate per tons mined during 1933 was about 10 times as great as for the mines employing 10 or more men. Another lamentable feature in connection with the fatalities in small mines is that very few carry any compensation insurance and the owners are not worth enough financially for dependents of victims to collect anything under the common law; as a result, the dependents of those killed usually are left penniless and subjects of public charity.

Feb 1, 1935

By S. L. Windes

This report presents a tabulation of the physical and petrographic properties of Over 100 rock types from operating mines or mineral-investigation projects. The physical properties include the following: Apparent specific gravity Apparent porosity Compressive strength Flexural strength, (modulus of, rupture) Impact toughness Abrasive hardness Scleroscope hardness Modulus of elasticity (Young's modulus) Modulus of rigidity Specific damping capacity Longitudinal bar velocity

Jan 1, 1949

By G. T. Krempasky

In an attempt to develop a suitable precast concrete support for underground use, two different models (1955 and 1958) of a five-piece concrete set were designed, fabricated, and tested under adverse loading conditions. Model 1955 was designed to withstand an ultimate, uniformly distributed, vertical load equivalent to what a three-piece, 12- by 12-inch wood set of intermediate-grade Douglas fir would withstand. A design figure of 138,000 pounds for the vertical load was used on both the 1955 and 1958 models. In addition, the 1958 model was designed to withstand a uniform horizontal load of 7,000 pounds per foot and additional concentrated-point loading. The step- by-step design of each model is presented in the appendixes. A series of five destruction tests was conducted underground on the 1955 model, and results of the tests showed that the type and method of blocking were of major significance.

Jan 1, 1963

By Wallace W. Roepke

Four bit designs, two conical and two radial, were tested in coal against a 60° conical reference bit to obtain data on orthogonal cutting forces and primary respirable dust generation. One conical and one radial design were modified by the Bureau of Mines for these tests. Results were mixed: One radial bit used substantially lower overall cutting forces and specific energy than the other bits and was the only cutter lower on energy and most forces than the standard 60° bit. How-ever, it generated more specific and total dust than any other bit. The four bits were also tested for incendivity, with a 90° plumb-bob bit as the reference. The frictional ignition tests were designed to simulate both trimming top rock and cutting such rock during advance on-sump. Results of these tests were also mixed. The radial bits were substantially less incendive than the reference bit and caused no ignitions in either top trimming or sump modes. Only the modified mushroom-tipped conical bit caused ignitions. Bits similar to this modified design should not be used on drum-type miners in gassy mine areas; in-stead, the other types of bits tested should be used to reduce ignition potential to a minimum.

Jan 1, 1983

By J. J. Taber

Gas and water permeabilities of a large number of samples from the Pittsburgh and Pocahontas coals were measured at various overburden and mean flow pressures. A wide variation in the air and water permeabilities was obtained for each type of coal. Overburden pressure has the most significant effect on the single-phase permeability. Considerable hysteretic effect was observed for both air and water permeabilities. Gas permeabilities are affected to a lesser degree by mean flow pressures above atmospheric. However, at subatmospheric mean pressures, appreciable increase in permeability occurs for low permeability samples. Air and water relative permeabilities were also measured for numerous samples of Pittsburgh and Pocahontas coals. Tests were performed under steady-state conditions for both drainage and imbibition cycles. Results indicate that the flow of gas is greatly reduced during the latter process, whereas it is largely undiminished over a wide water-saturation range during drainage. It is also shown that imbibition saturation distributions obtained from liquid-water imbibition as opposed to water-vapor adsorption produce gas permeability curves of radically different character. The effective permeabilities to both gas and water were significantly reduced with the application of overburden pressures in the range of 0 to 1,000 psig, but the general shapes of the relative permeability curves remained the same.

Jan 1, 1974

By Karl C. Dean

The Bureau of Mines stabilized 10 acres of windblown copper mill tailings at McGill, Nev., by a combination chemical-vegetative procedure. Legumes, winter wheat, wheat-grasses, and wild rye were seeded, and the area was subsequently sprayed with a resinous adhesive chemical to stabilize the sands until the vegetation could grow. During the year since treatment, the area has been well stabilized against wind erosion. The established vegetation appears to be capable of self-perpetuation and renewal without irrigation. The cost of stabilizing the area was $135.50 per acre.

Jan 1, 1969

By Fred W. Johnson

The first section of this circular has been prepared with a view to answering inquiries frequently received by the Bureau regarding laws governing the staking of claims and regulations covering requirements for holding them and obtaining title in fee to placer ground. These laws and regulations were summarized briefly in Information Circular 6796, "Placer Mining in the Western United States." These laws, however, are administered by the General Land Office, Department of the Interior, and it has been considered advisable to combine an authoritative résumé thereof by the Commissioner of that Bureau with information on small-scale placer mining previously published by the Bureau of Mines. The second section of this circular is largely a revised reprint of Information Circular 6611, "Small-Scale Placer Mining Methods", first published in April 1932 for the purpose of answering the many daily inquiries then being received on this subject. This circular has been reprinted repeatedly, and about 30,000 copies have been distributed, most of them in response to applications therefor. At present (June 1937) requests for this publication continue to be received daily.

Jan 1, 1938

By Richard F. Link

A statistical technique, useful to analyze assay and other data characterized by location in three dimensions, is described in this Bureau of Mines report. If present, trends in the data are defined for the purposes of improving ore estimation, predicting ore beyond existing workings, and aiding geological interpretation. The technique is to fit linear and quadratic polynomial equations to the data through the statistical method of regression analysis. The fitted linear equations have the geometric form of hyperplanes; the fitted quadratic equations have the geometric form of ellipsoids or elliptic hyperboloids of one or two sheets. To visualize these three-dimensional forms, contour maps of a series of plane sections through the fitted surfaces are plotted. Both the fitting of the polynomial equations and the plotting of the con-tour maps are done by electronic computer to facilitate calculations and to obtain accurate results. Computer programs are described in appendixes. Methods employed are illustrated by an example analysis) based on data from a part of the Fresnillo mine) Zacatecas, Mexico.

Jan 1, 1966

By C. T. Baroch

CESIUM-137 ISOTOPE began to displace cobalt-60 III the treatment of cancer during 1956. Production and Consumption.-Consumption of cesium and rubidium was approximately the same as in 1955. Production, however, decreased, as several companies shipped from stocks produced in previous years. South Africa was the source of most cesium and rubidium minerals used in the United States in 1956. Cesium and rubidium metals and compounds were produced from ore by: DeRewal International Rare Metals Co., Philadelphia, Pa.; Fairmont Chemical Co., Inc., Newark, N. J.; Foote Mineral Co., Philadelphia, Pa.; and Rocky Mountain Research, Inc., Denver, Colo. Most sales were to domestic consumers, but small quantities were exported to Australia, England, Germany, and Sweden. New production facilities were under construction in. 1956 by San Antonio Chemicals to produce mixed potassium, rubidium, and cesium carbonates. A plant capable of separating and packaging 200,000 curies of cesium-137 annually was under construction at Oak Ridge National Laboratory.6

Jan 1, 1958

By W. P. Yant

The hazard to health from contamination of air by a noxious gas depends not only on the potential harmful response attending exposure, but also on the warning properties, which in effect may be termed the "accompanying warning response," This warning may be manifested as an odor, taste, irritation of the eyes, nose, or throat, or perhaps headache, vertigo, or nausea. These manifestations may be painful and even slightly harmful, but to a much lesser degree than the primary injury of exposure. The warning response mitigates hazards directly in proportion to the degree of Intolerability which accompanies injurious exposure, and accordingly its absence augments hazards. This accounts for the fact that the actual health hazards from a non-odorous or non-irritating gas or vapor of comparatively low toxicity sometimes equal or exceed the hazard from a considerably more toxic substance, but one which possesses a marked odor or produces eye, nose, or throat irritation in advance of harmful exposure. When a substance lacks the properties for giving warning, it is often possible to impart them by the addition of a small amount of another substance which has an exceedingly high warning intensity. The vapors of this substance, commonly termed a "warning agent" or "tracer gas," escape and mingle with the gas or vapor which lacks warning properties and thereby apprises persons of the latter's presence. The amount of the warning agent added is that which will give adequate warning in advance of serious physiological harm from the dangerous gas or vapor.

Jan 1, 1930

By Thomas J. Peters

Tungsten, silver, lead, zinc, and placer gold occur in the Cucamonga B RARE II area (no. B5174). A strata-bound, scheelite-bearing zone at the Blue Diamond prospect (fig. 1, no. 1) contains an estimated 16,000 tons (15,000 t) of identified, subeconomic resources averaging 0.16 percent tungsten trioxide (W03). There is a high potential for discovering additional tungsten resources at this property. The California-Hercules prospect (fig. 1, no. 5) ha; a mineral occurrence which contains an estimated 1,000 tons (900 t) of tactite averaging 1.3 oz silver per ton (45 g/t), 0.75 percent lead, and 0.72 percent zinc. Another occurrence, at the Blew Jordam Prospect (fig. 1, no. 4) has an estimated 100 tons (90 t) of tactite averaging 10 oz silver per ton (340 ,/t), 3.75 percent zinc, and 2.3 percent lead. There is a moderate potential for discovering silver, lead, and zinc resources at these prospects, which are in metamorphic pendants. There are a few lode gold prospects in the area (fig. 1, nos. 3, 11, 14) are on geologic structures which parallel the San Andreas Fault, northeast of the area. These deposits are not well exposed and have been historically unproductive. Placer gold in area B occurs locally in the beds of intermittent tributaries to Lytle Creek (fig. 1, nos. 10, 12, 13) in concentrations as high as $1.17 per cu yd ($1.53/cu m, at a gold price of $450 per troy oz). The deposits have no significant volume, but could be utilized for recreational panning and suction dredging. In the Cucamonga C RARE II area (No. C5174) placer gold occurrences locally contain as much as $1.23 per cu yd ($1.61/cu m). However, gravel containing the gold appears to be limited to stream beds, and does not occur in sufficient quantity to constitute resources. Recreational panning and dredging also may occur in this area.

Jan 1, 1983

By Paul Hatmaker

A primary, function of the Bureau of Mines is to encourage elimination of waste and the most profitable use of mineral raw materials. In line with this objective the Bureau has frequently stressed the importance of waste utilization at stone quarries. From time to tine studies both technical and economic in character have been made of problems pertaining to the most efficient use of natural, stone, particularly that which may be classed as a by-product of the higher grades of dimension stone. Every quarry producing ornamental or building stone yields large quantities of material that for one reason or another is unsuited for high-grade products, even though a great deal of work has been expended upon it more or less unavoidably. It is obviously good judgment to sell this odd-sized or off-grade stone at whatever price can be obtained rather than to spend more money to place it on the waste dump. In many cases, however, a really profitable side line has been developed.

Jan 1, 1933