Search Documents

By R. J. Morrell

The Bureau of Mines conducted a series of laboratory experiments to test a cutting technique for hard rock using large-scale drag cutters. Cutting experiments were performed on rocks ranging in compressive strength from 10,000 to 27,000 Ib/in2, using large drag cutters from 3 to 6 in. in width. The tests were conducted on a special test apparatus, called a ripper tester, which made a curvilinear cut across the rock sample while measuring the cutting force acting on the drag cutter. The cutting method that evolved from these experiments is called ripper cutting, and its energy efficiency appears superior to all other large-scale mechanical fragmentation techniques. In addition, the method cre-ated very little dust, and the wear on the bits was negligible. A fragmentation system based on ripper cutting was then devised, and a large-scale test device was fabricated to allow full-scale laboratory testing of the system. The results of these tests will be published in future Bureau reports.

Jan 1, 1986

By Joe N. Magee

As part of the important program of promoting conservation and efficient utilization of petroleum, Bureau of Mines engineers are making studies of secondary oil-recovery projects throughout the United states and publishing reports setting forth the pertinent facts so that others may profit by the experience gained. This report presents the results of a study by engineers of the Bureau of Mines, stationed at Franklin, Pa., of secondary oil recovery in a part of the Cabin Creek field, Kanawha and Boone Counties, W. Va., where natural gas is injected into the reservoir to stimulate oil production. Most oil produced in the Appalachian region at present is obtained from stripper fields in which almost all natural energy has been dissipated. Secondary-recovery methods are used extensively in many oil-producing areas of New York, Pennsylvania, West Virginia, Ohio, and Kentucky for recovering oil not produced by primary-production methods. The part of the Cabin Creek field reported in this study is shown in figure 1 and has been designated by the operator as project 4. In 1944 the developed area of the entire field was approximately 4,200 acres, and the area of project 4 was about 600 acres. In the developed area of the project the oil reservoir is in the Berea sandstone and occurs at 2,914 to 3,410 feet.

Jan 1, 1952

By C. W. Smith

Research was conducted to evaluate the effectiveness of a well-point dewatering system in conjunction with a french drain to intercept waste impoundment leakage while reducing the volume of waste water requiring treatment. A well-point dewatering system composed of 585 production wells was installed around the perimeter of a leaking impoundment that previously used only a french-drain system for leakage control. The placement of the well-point system was designed to intercept and remove the leakage from the groundwater before the contaminant reached the french drain. Groundwater monitoring at this site revealed that after a period of approximately 40 days the well-point dewatering system had stabilized and effectively prevented the further spread of contamination to the french drain.

Jan 1, 2010

By Miller, ALEX U, Edward Thomas

In March 1937 the entire country was shocked by news of an explosion of gas in a New London (Tex.) schoolhouse, which resulted in the death of 280 pupils and 14 t eachers. The Government investigators of this disaster believed that the cause was the ignition and explosion of a large volume of explosive natural gas-air mixture that had accumulated in a poorly ventilated space beneath the first floor of the main school building and that this accumulation was due to leakage from gas lin suspended underneath the floor to carry the gas supply to the school.!i/ For some years there has been a potential explosion hazard in school houses and other buildings that are supplied with water from deep wells in certain parts of Illinois. Notwi thstand.ing the disaster at New London, Tex., and the fact that there had been gas ignitions at four water wells in different parts of the State, the explosion hazard in schools and other buildings was not fully recognized until a few months after the disaster in Texas, when an explosion occurred in the settling basin of the municipal water works of Clinton, Ill., and another in a pump house of the municipal water works in Normal, Ill, The explosion in the settling tank of the municipal water works in Clinton, Ill., occurred on August 12, 1937, and a.id considerable damage to the settling tank, but fortunately no one was injured. At the time of this explosion rapairs'and aJ.terations to the water plant were in progress, and 10 men were employed in the immediate vicinity of the settling tank. Two of these men were enlarging a hole in the concrete side with an air hammer for the installation of a larger discharge line.

Aug 1, 1938

By Oliver Bowles

"The introduction into mines, quarries and manufacturing plants of machines and tools operated by compressed air has revolutionized methods of operation to an extent comparable only with that occasioned by the invention of explosives and the utilization of electricity. The use of compressed air in pneumatic tools, in rock drills, and for the operation of pumps and other machinery is well known to most miners and quarrymen, but its application as a substitute for explosives for breaking rock in a few granite quarries has received little publicity.In the region of Lithonia, a few miles from Atlanta, Georgia, is a dome of massive granite used widely for building stone and for paving blocks. The most remarkable structural feature of the granite is the absence of joints and sheeting planes. The term ""joints"" is applied to open fractures that commonly occur in rocks, usually vertical in direction or nearly so, and spaced from a few inches to several feet apart. On the Lithonia granite outcrop, however, one may walk over the bare rock surface for hundreds of feet without finding any indications of a joint, ""Sheeting planes"" are open fractures at various levels, approximately parallel with the rock surface. The presence of such planes when spaced several feet apart greatly facilitates quarrying, and where absent, as at Lithonia, the necessary fractures must be made artificially.The forcing of artificial sheeting planes is accomplished as follows: Two holes of about 3-inch diameter arc drilled close together and to a depth of about 8 feet. Two men work at these holes all summer, and sometimes part of a second summer. A very small charge of black blasting powder, not more than a spoonful, is placed in each hole, tamped with clay, and the charges are fired simultaneously with an electric battery. This starts a small fracture running outward from the bottoms of the holes. There is in most granites one direction of easy splitting known among quarrymen as the ""rift"", and as the rift direction in the Lithonia granite is horizontal the fracture follows a horizontal plane,"

Aug 1, 1920

By Maurice J. Peterson

THE VISUAL-ARC spectroscopic method of rapid qualitative analysis of complex inorganic compounds has been popularized in the past few years and is being employed by an increasing number of laboratories. The mineralogy and chemistry departments of several universities recently have added visual spectroscopy to their laboratory curricula. This revival of interest in a somewhat dormant analytical method has been stimulated through the publication of three papers 4 by members of the College Park staff of the Bureau of Mines. These virtually are the only recent sources of information on visual-arc spectroscopic analysis. They include data on the spectroscopic assembly, the analytical procedure, and the practical application of the method to determinative mineralogy and related fields. Requests for reprints of these papers continue to be received; at present only a limited number of copies are available for distribution. In order that these requests may be adequately answered, material from the three papers has been combined and, with some additional data, is presented in this bulletin. Numerous specific inquiries have been received regarding types of equipment available, problems in instrumentation, and information on the approximate sensitivity limits of the elements that can be detected by this method. Some of this material was not included in the original papers. Accordingly, the table of wavelengths has been revised to include the approximate visual-arc spectroscopic sensitivities, and a section on commercially available equipment has been added.

Jan 1, 1953

By D. E. Hirsch, J. W. Davis, Norman G. Foster, F. G. Schwartz

This investigation was undertaken to identify nitrogen , oxygen , and sulfur compounds (polar components ) found in catalytically cracked distillate fuel . It is significant that these compounds concentrate in the sediments and gum that form when the fuel is stored . The polar components were divided in three portions by elution from a chromatographic column filled with alumina . After the hydrocarbons were washed through the column with pentane , a benzene eluted extract was removed followed by an ether eluted extract and then an alcohol desorbed fraction . These extracts were individually distilled in a molecular still and the fractions were analyzed by gas chromatography , mass spectrometry , infrared spectrometry , and elemental and functional analyses . Naphthalene and its homologs , phenanthrene and its homologs , and other compounds such as methyl indene , C₂ quinolines , phenyl indan , and the benzothiophenes , appear in the benzene extracts . Quinolines are the major components of the lower boiling fraction of the ether extract , although carbazoles , acridans , and indoles are present in some concentration . Elemental and functional group analyses of the alcohol fraction indicated 10 percent of the distillate portion was nonhydrocarbon , and in this portion the average molecule contained more than one nonhydrocarbon element . Compounds of such complexity are not well known , and standards for positive identification are limited .

Jan 1, 1963

By H. Winkelmann

The author, who himself has worked inn the field with various types of torsion balances, expresses in the article his experience with the recently marketed Haff-Torsion-Balance. The advantages of practical work with Haff?s s torsion balance as compared with other types are mentioned. In spite of low weight and corresponding small dimensions (Model M = 23.5 kg., Model Al = 11.5 kg.) the sensitiveness is not less than that in the largest instruments. It is at 1.10-9, which is proved by calculations. A comparison with the corresponding values of other types of torsion balances (Eötvös, Askania, Gepege) is given. The mechanical features of the instrument are briefly described, and the balance is illustrated by a, cross section of it. -- W. Ayvazoglou. DETERMINATION OF THE ELEMENTS OF THE MAGNETIC AND GRAVITATIONAL FIELDS INDUCED BY AN INFINITELY LONG HOMOGENEOUS CYLINDER By G. A. Gamburzeff Gerlands Beiträge zur Geophysik, Band 19, Heft 2/3 Leipzig, 1928, pp. 210-230. The present work is a. contribution to the quastion of the reason for the magnetic and gravitational anomalies in the government of Kursk (Russia).

Jan 1, 1929

By Robert C. Dyni

This U.S. Bureau of Mines (USBM) report summarizes a field demonstration of pneumatic backfilling technologies conducted at the abandoned Hillside Coal and Iron Slope in Vandling, P A. Researchers demonstrated two pneumatic backfilling technologies recently developed under the USBM's Abandoned Mine Reclamation Research Program, the Pneumatic Pipefeeder and the High-Efficiency Ejector. Both systems had previously been evaluated at the USBM's subsidence abatement investigation laboratory near Fairchance, P A. The objective of the demonstration was to fill 100% of the abandoned tunnel with backfill stone to prevent further subsidence. The Pneumatic Pipefeeder was used for 21 days, at a rate of 63 to 124 t/ d (69 to 136 st/d), to fill 88% of the tunnel. The High-Efficiency Ejector was used for 2 days, at a rate of 125 to 132 t/d (138 to 146 st/d) to fill the remaining 12% of the tunnel. The backfill placed by both systems was tightly compacted. The major problem encountered was wear on the polyethylene pipeline from the abrasion of the high-velocity backfill. The use of heavier steel pipe minimized the problem. A cost analysis for the entire project is given.

Jan 1, 2010

To concentrate coarse mica particles using a dry beneficiation technique. Approach Concentrate coarse, II berated mica particles using a Bureau-designed system of crushers, screens, and a two-stage zigzag air classifier. How It Works Because mica has a flat plate-like crystalline structure, mica particles are significantly lighter than blocky gangue particles of the same size fraction. Thus an air classification technique can separate the flat, light mica particles from the heavier gangue particles. The ore, which Is first run through a standard jaw crusher, a roll crusher, and a hammer mill to liberate the mica, enters the rougher Zig-zag section through a rotating air lock. See photograph and diagram of a 2-stage air classifier. Airflow through the classifier can be varied according to the size of the particles being separated. The gangue material falls through the airstream of the rougher zigzag section and is discarded as tailings. The mica flakes are carried by the air-stream to the cyclone shown on the right side of the diagram, where they are collected. This rougher mica concentrate is fed to the cleaner zigzag section through another rotating air lock. The mica particles are again carried by the airstream but they are now collected In the cyclone on the left side. The cleaner concentrate leaves the left-side cyclone through a third rotating air lock and is rescreened to remove under-size material missed by the first screening. The final product of this pneumatic process is generally a high-grade mica concentrate. A generalized flow diagram for the pneumatic concentration method Is shown In the second diagram.

Jan 1, 1981

By O. C. Blade

Studies on more efficient utilization of petroleum have been made for 50 years by the Bureau of Mines. As part of this work, the Bureau has analyzed thousands of samples of crude oil by its standardized routine method, and many of these analyses have been published, sometimes in special compilations, other times in connection with reports of research on petroleum. This report is a finding index for all analyses published from 1921 to 1959, and brings up to date the information in Information Circular 7470 3 and in the appendix of Bulletin 490.4 The routine method of analysis and the equipment originally were described in a report by Dean and associates. 5 This report has long been out of print, but Bulletin 490, bringing the procedure and its modifications to date, was published in 1951. 6 Briefly, the procedure consists of testing, by standard methods, small samples of a crude oil for gravity, sulfur, color, viscosity, pour point, and (more recently) nitrogen; and, by a standardized procedure, distilling a portion of the crude oil and determining certain properties on the separated fractions and residuum. Careful records are made during the procedure, and the distillation data obtained are used to compute the approximate amounts of products present in the sample--such as percentages of gasoline, kerosine, gas oil, and lubricants. The principal data and results are recorded on a standard analytical report form. An analysis of a sample of crude oil from a recently developed field is shown in table 1. Compilations of these analyses, sometimes in tabular form and usually for specific geographic areas, are published from time to time. Analyses often are included in connection with other studies, such as engineering field reports.

Jan 1, 1959

By Oliver Bowles

"Rhodesian asbestos is of high quality and is much in demand by American consumers. Production in Rhodesia was first reported in 1909. The production for this and each succeeding year is shown in the following table:The serious curtailment in production for the years 1912 and 1913 was occasioned by transportation difficulties. In 1914 a railway was projected to Victoria and thereafter production increased greatly. Up to 1916 asbestos was obtained,from the Victoria district only, but thereafter the Bulwayo district became an important,producer with minor quantities from Gwelo.In the Bulawayo district the productive area is about 2 1/2 miles long, with Shebanie mine at the north-west end, the Nil Desperandum at the south end, and the Birthday claims between them."

Oct 1, 1920

By Dana C. Reinke

A job analysis is a written list of the tasks associated with doing a particular job. In drilling, describing the steps associated with adding rod to the drill steel would be an example of a task associated with the job. How to hammer casing or fish a lost drill bit out of a hole would also be job tasks. Develop a written list of job tasks. Ask drillers in your company if the tasks listed are correct and accurately reflect how to perform the job. While each driller may do the job a little differently, some tried?and?true methods are required to perform certain tasks safely and correctly. You may find a separate analysis is needed for different drilling jobs (e.g., a residential well or a monitoring well). Also remember to include the tasks of both the helper and the driller.

Jan 1, 2005

By H. W. Kilau

Thermodynamic calculations indicate that an electrochemical cell might serve as an analytical device for determining the composition of high-purity metals. An equation, readily derived, for the cell voltage, E, is as follows: [E I RT In F NFe unknown sample T of L NFe standard] The cell, however, must come to equilibrium, must be reversible, and must have no thermal effects or complicating side reactions whose magnitude is indeterminable. This Bureau of Mines investigation explores the feasibility of an electrochemical technique for the analysis of high-purity iron. Experiments were conducted using room-temperature aqueous cells and high-temperature molten salt cells. The room-temperature cells proved to be irreversible. The high-temperature cells utilizing FeCl2 and a eutectic mixture of KC1-LiCl were reversible, but did not attain a constant voltage necessary for analytical considerations.

Jan 1, 1963

By Kyei-Sing Kwong

The U.S. Bureau of Mines investigated the synthesis of advanced ceramics (SiC+AlN, SiAlON, SiC+A1203, and Si3N4+AlN) from natural clays (kaolin, halloysite, or montmorillonite) by an intercalation and heat treatment method. This process includes the steps of refining a clay, intercalating organic chemicals into its layered structure, drying the intercalated mixture, firing the treated structure at certain temperature ranges in controlled atmospheres to form desired compounds, and grinding the loosely agglomerated structure. Focus of this research is to economically process advanced ceramic structures from abundant natural resources. The advanced ceramic phases produced in this simple treatment are homogeneously distributed at the nanostructure level, and may potentially lead to cost effective manufacturing processes. The intercalation of clay was confirmed by X-ray and BET analyses. The evolution of chemical compositions during carbonization reactions and carbothermal reduction was investigated. The characteristics of refined clays and synthesized powders were studied. Advanced ceramic composites/solid solution have been produced from intercalated clays, without the presence of other compounds.

Jan 1, 2010

By W. A. Selvig

"The tests described in this paper were conducted under the sponsorship of Subcommittee VII on Pulverizing Characteristics of Coal, a subcommittee of Committee D-5 on Coal and Coke, American Society for Testing Materials, with a view to evaluating various laboratory procedures for testing grindability of coal in connection with commercial pulverization of coal for use as powdered fuel. The subcommittee, at a meeting in New York City on February 21, 1934, selected for test four methods that had been developed during the past few years for testing grindabilitay of coal and were being used by coal-testing laboratories in the United States and Canada. These methods are:Bureau of Mines method, Cross method, Fuel Research Laboratory method, and Hardgrove method. Subcommittee VII agreed that the grindability tests should be made on five coals selected to cover a wide range of hardness. The Pittsburgh Experiment Station, Bureau of Mines, was asked to direct the investigation and to prepare representative samples of the coals. Laboratories of the fol. lowing institutions and companies agreed to cooperate by making grindability tests: Babcock & Wilcox Co., Foster Wheeler Corporation, Fuel Engineering Co., of New York, Fuel Research Laboratory of the Canada Department of Mines, and Northwest Experiment Station of the Bureau of Mines.ACKNOWLEDGMENTSHelpful suggestions in planning the investigation were made by A. C. Fieldner, chairman, Committee D-5 on Coal and Coke, A.S.T.M., and chief engineer, Experiment Stations Division, U. S. Bureau of Mines, Washington, D. C., and E. B. Ricketts, research engineer, New York Edison Co., New. York City.The coal samples were supplied through the courtesy of floats, Wheeler Corporation, New York City; Philadelphia & Reading Coal & Iron Co., Pottsville, Pa.; Pittsburgh Coal Co., Pittsburgh, Pa.; and Pocahontas Fuel Co., Inc., New York City."

Feb 1, 1936

By John C. Machisak

Employment and related injury experience of the coking industry in the United States for 1956 contained in this publication is summarized under three general sections: (A) General injury experience: Tables 1 to 9: Current and comparable statistics on operating data, number, frequency, and degree of severity of injuries and major accident agencies involved in the cause of injuries. Data are presented for the industry as a whole, for each type of oven, and for the States in which coke was produced. (B) Selected injury experience: Tables 10 to 15: Comparable injury data covering 5- and 10- year periods on the number and degree of severity of injuries and major accident causes.

Jan 1, 1958

By G. W. Reimers

Exothermic oxidation reactions of sulfide minerals can produce self-heating situations in underground mines. If the self-heating is unchecked and the resulting heat is not sufficiently dissipated, the result can be spontaneous combustion fires. This U.S. Bureau of Mines report describes laboratory tests conducted to measure the reactivity of pyrite following treatment with additives to counter its self-heating tendencies. Thermal gravimetric analysis (TGA) and isothermal oxidation procedures were used to obtain information on pyrite ignition and the behavior of pyrite during low-temperature oxidation to ferrous sulfate. The determination of treatment effectiveness was evaluated by adding 5 wt pct of the compound to the pyrite before milling. The resulting samples were then heated in moistened air and after 24 h, the amount of pyrite oxidation determined. Results of these tests indicated that several phosphate compounds reduced the oxidation of pyrite to sulfate to about 50 pct or less compared with the oxidation of untreated sample at 200° C. Cupric sulfate reduced oxidation to about 20 pet untreated sample at 200° C. Sodium, calcium, and potassium chloride reduced pyrite oxidation to levels of approximately 15 pct or less of the untreated sample. Using only 1 pct of sodium or calcium chloride was effective in slowing pyrite oxidation to less than 20 pct of the untreated sample.

Jan 1, 2010

This work presents: 1.) the results obtained from measurements of temperature profiles in pillars and at working faces of three coal mines located in Colorado and New Mexico, 2) a comparison of the experimental results with theoretical predictors based on linear heat flow models, and 3) temperature profile predictions based on a two dimensional coal mine model with an inclined crack located in the roof or wall of the opening. The thermal properties of the coal and shale samples taken from the mines were used as input data for the computer model. Good agreement was found between the measured profiles and the theoretical values obtained with the one dimensional model. The two dimensional model results show that a visible crack (0.01-0.07-ft thick) in a coal roof causes a surface temperature difference from 0.2 to 1°F at the edge of the crack for rock exposed to air from 1 hr to 288 hrs and with the air to rock temperature differences from 2°-6°F. A temperature difference of 0.3 °F was found between solid and broken rock in a shale roof with a 0.03-ft thick crack inclined 45° to the horizontal after a ventilating time of 48 hrs and the air to rock temperature difference of 2.1°F.

Jan 1, 1972

Significantly increase the amount of fresh air that sweeps the face in front of a continuous mining ma-chine, in order to prevent methane gas buildup. Approach Water sprays are mounted along the sides of a continuous miner and behind the cutter head to help push ventilating air along the required path, and prevent its short circuiting. How It Works A continuous miner is fitted with two sets of water sprays, one of which is used at a time. The set of sprays shown in the diagram, helps move the ventilating air forward along the left side of the miner and across the cutter drum from left to right. That air is then drawn into the exhaust air passageway located along

Jan 1, 1978