Search Documents

By A. W. Deurbrouck

This report describes the preparation characteristics of the significant coalbeds from which samples could be obtained in Webster County, W. Va. In 1964, approximately 825,000 tons of coal was produced in the county, of which 732,000 tons was mechanically cleaned in three preparation plants. The Sewell coal bed accounted for 94 percent of the coal produced. Twelve samples were collected from five coalbeds. Four of the samples would require upgrading to meet metallurgical requirements; two others of just over 8.0 percent ash would require some upgrading. In general the coalbed samples collected in the county were of medium-sulfur and medium-to low-ash content as received or after removal of the sink 1.58-specific-gravity material.

Jan 1, 1966

By C. M. McKinney

This report presents analyses of crude oil from most of the fields in the United States producing 2,500 barrels per day or more. The purpose of the report is threefold : 1) To present detailed analyses of crude-oil samples from as many al possible of the important fields in the United States. On January 1, 1947, there were 340 fields producing 2,500 barrels & day or more. Analyses for 283 of these fie1ds are presented. Fifty-seven fields have been omitted because the Bureau of Mines did not have analyses or the crude oils being produced. As one sample was not representative of the promotion from several of the fields, two analyses are given for each field of this kind. (2) To compile these analyses, many of which have not been published previously in a single report. Since the publication of Bulletin 291 in 1928, there has been no report showing analyses of crude petroleum from fields throughout the United states, but a number of separate reports according to area or state have been issued. Many of these are out of print. (3) To provide a means of ready comparison of the properties of crude oils from different areas of the United states.

Jan 1, 1948

By Basil Dimitriades

The roles of hydrocarbons and nitrogen oxides in smog formation were investigated by the Bureau of Mines. Samples of automobile exhaust with varying HC and NOx levels were irradiated in a smog chamber under conditions that resulted in smog levels similar to those observed in the atmosphere. Results were used to define the patterns that describe the dependence of a number of smog manifestations on HC and on NOx. Using these dependence data and some simplifying assumptions, estimates were made of the ranges within which HC and NOx must lie in order to obtain specified levels of air quality.

Jan 1, 1970

By W. W. Weller

Low-temperature heat capacities of scandium sesquioxide (Sc203) and a mixture of cerium sesquioxide (Ce203) and cerium dioxide (CeO2) were measured over the temperature range from 50° to 298° K. The entropy of scandium sesquioxide at 298.15° K was evaluated directly as S°298.15 = 18.4 ± 0.1 cal/deg mole. That of cerium sesquioxide was extracted by combining the heat-capacity data for the mixture with those for pure cerium dioxide; the result was S298.15 36.0 ± 1.0 cal/deg mole.

Jan 1, 1963

By A. C. Fieldner

The Bureau of Mires in its investigations of gas masks for use in mines and allied industries has studied and developed various types of masks for protection against noxious uses and furies that may be present in atmospheres encountered in mines, metallurgical works, chemical and other industries. As a result of these investigations, the Bureau issued a schedule5 of tests under which manufacturer who voluntarily submit masks for examination and test, are issued an approval certificate for masks that meet the Bureau's specifications. In the Bureau's schedule, masks arc classified by types of gases removed, as type A masks for protection against acid gases; B; organic vapor; C, ammonia; D, carbon monoxide; E, smoke, dust, and mist; F, special gases; combination types, and type N, for protection in air against all gases, vapors, and smokes. The purpose of this paper is to describe the physical and chemical tests that were conducted on a type N mask, the protective principles and construction of the essential elements of the canister and attachments, and the uses and limitations of this type of mask. The mask tested is known as the all-service mask, manufactured by the Mine Safety Appliances Co., Pittsburgh, Pa;, and was approved (approval No. 1403) by the Bureau on July 1, 1924, for protection from all classes of poisonous vapors, gases and smokes in air.

Jan 1, 1925

By S. E. Khalafallo

The Bureau of Mines investigated the kinetics of reduction of wustite and magnetite with carbon monoxide. A mechanism was postulated wherein the interaction between gaseous and absorbed carbon monoxide appears to be the rate-determining process. This mechanism fully accounts for the experimental rate equation JL.h relates th velocity of reduction to the pressure of the reducing gas at constant temperature. It also explains the variability of the heat of activation of the reduction process with the state of aggregation of the oxide material. The integrated rate equation is in perfect agreement with the experimental reduction-time curves.

Jan 1, 1966

By Patrick D. Plumb

The Juneau Office of the U.S. Bureau of Mines has undertaken a study of the environmental permitting process for major mines in Alaska to identify the effects ecosystem management has had or could have on the permitting process. To date, ecosystem management affects major mine permitting in Alaska primarily through the NEPA environmental assessment process. In Alaska, only the Forest Service has instituted ecosystem management in an overt and organized manner, while other agencies are doing so less directly. In recent Bureau of Mines publications, the mine permitting process has been described using case studies of several recently permitted mines in Alaska. The insights into the permitting process and the conclusions of these reports are reviewed and summarized. Several ecosystem management issues were identified in the case studies, including the need for: effective communication between agencies; standardization and coordination of NEPA environmental impact assessment and environmental monitoring programs among agencies, and assessment and selection of alternatives based on risks to ecosystems regardless of jurisdictional boundaries or environmental media-specific regulations. Ecosystem management could be used as a way to systematize, organize, standardize, and coordinate permitting and monitoring requirements and management perspectives among government agencies and project proponents.

Jan 1, 1993

By Raymond M. Stateham

The Bureau of Mines used portable infrared scanners to examine the surface of pillars and faces in the Somerset mine near Somerset, Colo. Zones of temperature buildup, indicative of potential combustion, were detected with the scanners; their existence was verified by temperature measurements with conventional instrumentation. Temperatures of 32° to 6° C were measured on surfaces with normal temperatures of 26° to 35° C. The infrared instruments and techniques appeared to offer a rapid and efficient method for locating potential trouble spots in mines susceptible to fires caused by spontaneous combustion.

Jan 1, 1974

By Stephen Krickovic

Air quantity-pressure and methane concentration surveys were conducted by the Bureau of Mines in accessible portions of an area being pillared in a Pittsburgh coalbed mine in West Virginia. These included two mined-out and three active butt headings and a bleeder system. The particular mine workings were started in virgin coal directly from a set of main headings; the main reason for the study was the difficulty usually encountered in adequately bleeding the gobs under such conditions. Although the two separate return airways in each active butt heading and the North and 1 Left bleeders contained acceptable methane concentrations (0.01 to 0.78 percent in the butts and 0.73 to 1.0 percent in the bleeders) with significant total methane removal (109 cfm in butts and 631 cfm in bleeders), there were relatively large areas in the gobs with possible minimal airflows. This condition appears to have developed from lack of systematic regulation of the airflow across the gobs and appears to indicate the existence of considerably more methane in the probably low flow areas in the gob.

Jan 1, 1973

By R. F. Abernethy

A chemical method of determining microgram quantities of arsenic in coal was investigated by the Bureau of Mines to supplement a semiquantitative spectrographic method of determining arsenic in coal ash. In accordance with a method recommended by the International Organization for Standardization, 1-gram samples of coal are decomposed by wet oxidation with boiling sulfuric acid (H2S04) and nitric acid (HN03) to remove the organic matter. After heating to fumes of SO3 to remove HN03, the arsenic is separated as arsine by the action of zinc in H2S04 solution. The arsine is absorbed in dilute iodine solution in which the arsenic is determined colorimetrically by the molybdenum-blue reaction. Two modifications of the method for obtaining the arsenic in solution, in addition to the wet oxidation method, give satisfactory results. The modifications are (1) furnace ashing with MgO added to the coal, followed by treatment with H2S04, and (2) extraction of arsenic from the coal by dilute HNO3 without ashing. Float-and sink-tests show that arsenic is associated mainly with mineral matter in the three coals examined. High-temperature ashing tests show that very little arsenic is volatilized from coal ash below 1,000° C, but it is virtually all removed from the ash at 1,300° C.

Jan 1, 1968

By R. H. Nafziger

Bureau of Mines research has shown that very low-sulfur pressure vessel steels with improved mechanical properties can be prepared by two melting processes. Four pressure vessel steels having sulfur contents ranging from 0.0008 to 0.0040 wt-pct, were produced by the electric-arc furnace or by the electroslag processes. Calcium carbide was used as a desulfurizer in the electricarc furnace. Fluxes containing at least 40 wt-pct CaO provided sufficient desulfurization during electroslag remelting. Element recoveries were higher for electroslag remelting than for metal melted in the electric-arc furnace. Bar rolled from electroslag-remelted ingots generally possessed higher tensile strengths and ductility than bar rolled from it t melted in the electric-arc furnace. Charpy V-Notch upper shelf energies were also improved as a result of electroslag remelting. The primary failure mode during impact testing was was microvoid coalescence. Sulfide inclusions were minimal, especially in the electroslag-remelted material.

Jan 1, 1979

By Wesley T. Holmes II, Lloyd H. Banning

Electric - smelting studies were made on titaniferous materials obtained from the Klukwan and Snettisham , Alaska ; Choteau , Mont .; and Iron Mountain , Wyo . , deposits with the objective of determining the feasibility of producing pig iron and an enriched titania slag in one test series and pig iron alone in another test series . In addition , related studies were conducted to determine the amenability of Choteau crude ore to wet -magnetic separation and to determine the quality of steel that could be produced from the titaniferous pig iron . The continuous smelting tests were made in a three - phase , submerged - arc , electric furnace , and the laboratory steelmaking tests were made in a singlephase electric - arc furnace . A continuous , belt - type , wet - magnetic separator was used in conjunction with a ball mill and a spiral classifier in recovering titaniferous magnetite from the crude Choteau ore . Pig irons containing less than 0.05 percent phosphorus or sulfur were readily produced from the titaniferous materials ; iron recoveries ranged from 92 to 98 percent . The Choteau ore was ground to minus 65 - mesh to produce a concentrate containing 60 percent or more iron . The steel produced from the titaniferous pig iron was a high - quality product .

Jan 1, 1964

By BUREAU OF MINES

A complete list of permissible mining equipment, rescue apparatus and gas masks tested prior to July 1, 1928, was published in Bureau of Mines Information Circular 60772. The present list includes practically all equipment tested and, approved by the Bureau, up to and including Jan. 1, 1929. It covers electric air compressors, coal drills, mining machines, loading machines, conveyors, mine pumps, room hoists, mine telephones, rock-dusting machines, switches, electric cap lamps, flame safety lamps, electric hand and trip lamps, flash lamps, methane indicators and detectors, blasting units, storage barrery locomotives, tandem locomotives, power trucks, concrete mixers, self-contained oxygen breathing apparatus and gas masks. The system under which those devices were tested permits the manufacturer, after his equipment has passed certain tests prescribed by the Bureau of Mines, to mark his equipment with a seal shoring that it has been "approved" by the Bureau. These tests are designed to insure that the equipment has the minimum requirements for safety in use. The only object of the Bureau in making such tests and pub- lishing lists of permissible equirment is to safeguard the lives of workers and to help lesson the hazards of mining.

Jan 1, 1929

By K. K. Kelley, L. B. Pankratz, W. W. Weller

The heat capacity of columbium (niobium) carbide (CbC ) was measured over the temperature range from 51 ° to 298 ° K, and the entropy at 298.15° K was evaluated . Also , the heat content above 298.15 ° K of columbium carbide was measured to 1,800 ° K. The results were combined with the known heat of formation at 298.15 ° K to obtain values of the heat and free energy of formation over the temperature range from 298.15 ° K to 2,000 ° K.

Jan 1, 1964

By R. V. Ramani, W. Miola

"A relationship exists between the quartz contents in the underground coal nine airborne dust samples and those in the coal and host rocks that are mined [17, 18, 19] The prescribed method for quartz analysis in respirable airborne coal dust samples is the MSHA P-7 method. Accurate quartz analysis procedures are needed for bulk samples in order to predict the potential quartz content in airborne nine dust, which in turn will aid the design of quartz dust control procedures during mining. thereby reducing the airborne quartz dust in underground atmospheres. The requirements of this method are that the amount of quartz is the sample be less than 250ug, and the total sample weight less than 2,500 ug. Unlike with airborne dust samples, there are no limitations to the available mass of bulk samples. However, these are no standard procedures for the preparation of bulk samples for scanning or prescribed methods for quartz analysis. The NIOSH and MSHA methods are certified for roped* dust and the acceptance of these methods for bulk samples assumes that the bulk samples will be reduced to the conditions specified for respirable dust samples. An alternative method is X-ray diffraction, which provides higher average quartz values than those obtained from P-7 method for the same samples.An investigation was carried out to determine the optimal procedure for preparing the bulk samples for the IR and XRD analyses. In this paper, the investigations on the effects of calibration, particle sizes, matrix composition, interferrous, and behavior of the filter substances on IR, XRD and FTIR results are presented. The error introduced by the presence of kaolinite and a new sample asking procedure to reduce it are discussed. The problems experienced with conventional sample holders for scanning were eliminated with the design and development of a new hollow sample holder. Quantitative comparison of quartz determinations by IR, XRD and MR methods on coal, roof and floor rocks, and airborne dust samples are presented. The important factors affecting the results of quartz analysis methods are: 1) bulk sample preparation for obtaining representative and homogeneous analysis samples: 2) particle size distributions of the analysis samples and calibration standards; 3) qualitative matrix composition of the analysis sample; 4) matching calibration standards to analysis sample; 5) substrates for sample deposition during analysis sample preparation; 6) procedures for analysis sample mounting; 7) selection of proper portions of she response profile for insanity measurement; and 8) interferences of spurious phases with the critical analyses. The recommendations of this study are important to enable comparisons and interpretations of analysis and research results."

Nov 1, 1995

By E. J. Gleim

A list of permissible mine equipment, tested and approved by the Bureau of Mines previous to January 1, 1942, was published in Bureau of Mines Information Circular 7207.3/ The list of that date was complete as to equipment then available and in current use. Information Circular 7240,4/ published as a supplement thereto, listed equipment approved curing the calendar year 1943. The present list is another supplement covering approvals issued during the calendar year 1943. The items are numbered to indicate the consecutive order in which each type of machine or device was approved in its particular classification. Thus, Information Circular 7207 gave 19 drills and drilling machines on the Bureau's active list. No additional approvals were given in 1942, but the three issued in 1943 bring the total to 22. Item 102, under Loading Machines and Conveyors, also appeared in Information Circular 7207, and items 120 and 124 appeared in Information Circular 7240. These numbers are repeated here to show that approvals were granted during 1943 for additional voltages on machines previously listed for one voltage only. Equipment listed in these circulars is approved by the Bureau of Mines only when found upon inspection and test to comply with minimum standards of safety as outlined in schedules prepared on the basis of many years of experience in dealing with safety problems of the coal-mining industry. The use of such equipment in mines known to be gassy, as well as in those that may become so, is earnestly recommended in the interests of safety. This circular is published so that the industry may be kept

Jan 1, 1944

By S. H. Ash

THE INUNDATION of anthracite reserves in the Eastern Middle field of Pennsylvania affects the life of the anthracite industry in this field; it also influences the economic status of people, communities, and industries that depend wholly or in part upon anthracite for their livelihood. The trends of production and of employment in the anthracite-mining industry in this field are downward, and they probably will continue in this direction. The reserves have been depleted to the extent that the end of the active life of the industry as a. major economic factor is approaching. By removing the water in those pools where it can be done economically, the future of this industry may be extended somewhat.

Jan 1, 1950

By Todd M. Ruff

The majority of fatalities that occur in road construction work zones in the United States involve a worker being struck by a piece of construction equipment or other vehicle. The Spokane Research Laboratory of the National Institute for Occupational Safety and Health, in cooperation with the Washington State Department of Transportation, is evaluating methods to decrease these accidents. One such method uses devices that assist equipment operators in monitoring blind areas around the equipment to prevent collisions with workers on foot or other objects. Several cameras and sensor systems are available for this application, and a study was conducted to evaluate these systems on various trucks used in road construction and maintenance. Tests were conducted using sanding trucks during the winter months, which allowed researchers to investigate the effectiveness and limitations of various technologies under the most extreme conditions. Tests were also conducted using dump trucks during the warmer months to study the effectiveness of the systems in highway work zones. Results show that many difficulties arise when using camera and sensor systems in cold, snowy climates. And, while the operation of these systems is more reliable during the warmer months, challenges still exist in using them on equipment in crowded work areas.

Jan 1, 2004

By Stephen R. Iverson

Mineral deposits examined in and near the Raywood Flats RARE II area have low potential for development. The Mill Creek Mine (fig. 1), has produced about 14,000 tons (13,000 t) of marble, and another 5.5 million tons (5.0 million t) of marginal marble reserves suitable for lime, chemicals, and cement production are estimated to remain at this deposit. However, nearly all the marble is outside the study area. The deposit is marginal because alternate sources of marble are closer to markets. A tungsten occurrence in the marble is too small and low grade to be considered a resource. Ten tons (9.1 t) of uranium- and thorium-bearing material have been mined from a pegmatite dike at the St. Patrick Mine. However, this occurrence also is too small and low grade to be considered a resource. More than 400 lode and placer claims have been located in or near the study area. There are no current claims or mineral, oil and gas or geothermal leases.

Jan 1, 1983

By J. M. Mutmansky, C. Lee

"Measurement of the size and elemental characteristics was performed on airborne coal mine dust samples collected by multi-stage cascade impactors as well as channel samples of the geologic materials. Size distributions were obtained using precise weighing techniques on the impactor substrates. Elemental analysis on the samples was performed by the proton-induced x-ray emission (PIXE) method, a rapid and non-destructive method of multi-element analysis.The various analyses were performed on 9 major and 21 trace elements. The results indicate the importance of intake air and shuttle car movements as sources of dust. The association of coal dust characteristics with channel samples was investigated using the coefficient of proportional similarity as a statistical measure. Results show a strong relationship between major elements and the geologic material being cut but a similar relationship between trace elements and geologic materials is not consistent.1. INTRODUCTIONThe most significant occupational disease in the coal industry is known ·as coal workers' pneumoconiosis (CW'P). While CW'P has existed for centuries, its mechanism of occurrence and association with coal dust has been well understood for only a few decades. In the 1930s, the significance of this disease led state and government officials in the USA to perform extensive epidemiological and environmental studies in the major coalfields. Study of these results plus later studies in the coal producing countries of Europe eventually led to the dust regulations that appear in the Federal Coal Mine Health and Safety Act of 1969.The impacts of the 1969 act were a productivity decline and increased production cost. Many analysts attributed this in large part to difficulties in complying with the new dust standards (Brezovic 1981). However, compliance was met in most continuous miner sections rather quickly. The remaining problem area is that of longwall mining where the procedures and layout of the minin~ system make it difficult to meet the standards."

Jan 1, 1989